Intermec IF2 Low-Level Reader Protocol Programmer's Reference Manual
Intermec IF2 Manual
![]() |
View all Intermec IF2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec IF2 manual content summary:
- Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 1
LLRP Low-Level Reader Protocol Programmer's Reference Manual - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 2
intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec Intermec Technologies Corporation. © 2009 by Intermec Technologies Corporation. All rights reserved. The word Intermec, the Intermec of Intermec Technologies - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 3
released as version -001. Version Number 002 Date 11/2009 Description of Change Revised to include information for new ETSI standard forRF products. Low-Level Reader Protocol Programmer's Reference Manual iii - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 4
iv Low-Level Reader Protocol Programmer's Reference Manual - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 5
12 ROSpec Preemption 12 Momentary Connections 12 Intermittent RFID Module Connections 12 Out-of-Band LLRP Configuration 13 Listen-Before-Talk 13 Client Termination 13 Network Layer Support 13 TCP 13 IPv6 13 TLS 14 Reader-Initiated Connections 14 Parse Errors 14 Vendor Extensions - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 6
Reset Event 17 ROSpecLoop Event 17 vi Low-Level Reader Protocol Programmer's Reference Manual - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 7
Overview of the Low-Level Reader Protocol This programmer's reference manual defines the architecture of the Low-Level Reader Protocol (LLRP) intended for use with Intermec RFID readers. LLRP Reader implementation provides control of RFID air protocol operation timing and access to air protocol - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 8
Capabilities Feature Device Manufacturer Name Firmware Version Can Set Antenna Properties Air Protocol Supported Has UTC Clock Capability Receive Sensitivity Support 1963 String matching platform version No EPCC1G2 only Yes No 8 Low-Level Reader Protocol Programmer's Reference Manual - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 9
among firmware releases; therefore, that documentation is outside the scope of this manual. Default AntennaConfiguration and AntennaProperties By default, the following configuration will be used for each supported antenna: • Maximum transmit power. • The default channel, as specified by the reader - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 10
based on the IM5R2 module, for example the IF61A, do not support AntennaEvents. LLRP Reader implementations based on the IM5R3 module, for example the IF61B Fixed Reader, fully-support AntennaEvents. Default ROReportSpec Configuration Default behavior related to ROSpec reporting is listed in the - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 11
ends, or when the operation count has been exhausted. The Intermec LLRP Reader implementation interprets AcessReportTrigger to generate a report at the end of any AISpec containing access results. Optional Feature Support This section describes the support of features marked as optional by the LLRP - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 12
supports recovery of undetected abandoned LLRP connections through the use of momentary connections, as described in section 18.1 of the LLRP v1.0.1 specification. Intermittent RFID Module Connections The LLRP Reader implementation handles cases where an RFID module has an intermittent - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 13
band through the defined LLRP protocol. No configuration of LLRP parameters or defaults are provided out-of-band (from a platform web interface or Intermec SmartSystems). Modification of parameters related to the LLRP Reader Service is allowed on a perplatform basis. A list of these parameters is as - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 14
IANA assigned manufacturer ID for Intermec, 1963. An XML file describing the extensions and their structure, conforming to the LLRP Toolkit (http://llrp.org) v1.0 XML schema, is available for download from the web interface on the IF61 Fixed Reader. Support for vendor extensions, their effectiveness - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 15
Reporting requires a valid license on some platforms. The following is a list of supported spacial ID custom parameters that are allowed within the SpecParameter choice. One or through the custom parameter IntermecTagSpeed (subtype 15). Low-Level Reader Protocol Programmer's Reference Manual 15 - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 16
Log custom event are useful only to Intermec Engineering. For example, a Low-Level Log may be requested by Intermec Engineering to optimize an RFID installation. ROSpec Looping A custom parameter is the SpecParameter choice of the ROSpec. 16 Low-Level Reader Protocol Programmer's Reference Manual - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 17
Event A pair of custom events are provided to notify the LLRP client that an internal LLRP reader reset event has occurred. In most cases, a reset event will be the result of a enable looping for ROSpecs, see "ROSpec Looping" on page 16. Low-Level Reader Protocol Programmer's Reference Manual 17 - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 18
18 Low-Level Reader Protocol Programmer's Reference Manual - Intermec IF2 | Low-Level Reader Protocol Programmer's Reference Manual - Page 19
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2009 Intermec Technologies Corporation. All rights reserved. Low-Level Reader Protocol Programmer's Reference Manual *937-017-002* P/N 937-017-002
![](/manual_guide/products/intermec-if2-lowlevel-reader-protocol-programmers-reference-manual-1c12fb4/1.png)
LLRP
Low-Level Reader Protocol
Programmer’s Reference Manual