Intermec IV7 IV7 Declaration of Conformity

Compliance

Statement

Insert

Device

Name:

RFID

Forklift

Mounted

Serial

Reader

Model

Number:

Model

IV7

The

responsible

party

for

the

compliance

of

this

device

is:

Intermec

Technologies

Corporation

6001

36

th

Avenue

West

Everett,

WA

98203

USA

(425)

348-2600

This

product

conforms

to

the

following

approvals.

The

user(s)

of

this

product

are

cautioned

to

use

accessories

and

peripherals

approved

by

Intermec

Technologies

Corporation.

The

use

of

accessories

other

than

those

recommended,

or

changes

to

this

product

that

are

not

approved

by

Intermec

Technologies

Corporation,

may

void

the

compliance

of

this

product

and

may

result

in

the

loss

of

the

users

authority

to

operate

the

equipment.

This

device

complies

with

Part

15

of

the

FCC

Rules.

Operation

is

subject

to

the

following

two

conditions:

(1)

This

device

may

not cause

harmful

interference,

and

(2)

this

device

must

accept

any

interference

received,

including

interference

that

may

cause

undesired

operation.

FCC

Digital

Emissions

Compliance

This

equipment

has

been

tested

and

found

to

comply

with

the

limits

for

a

Class

A

digital

device,

pursuant

to

part

15

of

the

FCC

Rules.

These

limits

are

designed

to

provide

reasonable

protection

against

harmful

interference

when

the

equipment

is

operated

in

a

commercial

environment.

This

equipment

generates,

uses,

and

can

radiate

radio

frequency

energy

and,

if

not

installed

and

used

in

accordance

with

the

instruction

manual,

may

cause

harmful

interference

to

radio

communications.

Operation

of

this

equipment

in

a

residential

area

is

likely

to

cause

harmful

interference

in

which

case

the

user

will

be

required

to

correct

the

interference

at

their

own

expense.

Canadian

Digital

Apparatus

Compliance

This

Class

A

digital

apparatus

meets

all

requirements

of

the

Canadian

Interference

-Causing

Equipment

Regulations.

Cet

appareil

numerique

de

la

classe

A

respecte

toutes

les

exigences

du

Reglement

sur

le

materiel

brouilleur

du

Canada.

This

device

contains

a

radio

frequency

transmitter

approved

by

the

Federal

Communications

Commission.

WARNING:

Per

the FCC

radio

frequency

(RF)

exposure

requirements,

(1)

Antennas

must

be

supplied

and

installed

as

recommended

by

Intermec

Technologies

Corporation

to

insure

compliance

to

RF

exposure

requirements.

The

antennas

approved

for

use

are

Intermec

part

numbers

805-622-002,

805-623-002,

and

805-626-001.

Correct

antenna

mounting

is

fully

described

within

the

Intermec

IV7

Quick

Start

Guide.

(2)

When

installing

and

using

Intermec

approved

remote

antennas

associated

the

RFID

tag

reader,

a

23

-cm

(9.1

-inch)

passing

distance

must

be

maintained

from

any

body

part

of

the

user

or

nearby

persons

and

the

remote

antenna.

The

antenna

must

not

be

touched

during

transmitter

operation.

(3)

Cables

attached

to

the

remote

antennas

must

have

a

minimum

length

as

provided

from

Intermec

to

insure

the

proper

losses

to

control

RF

exposure.

(4)

RF

safety

requirements

mandate

this

device

cannot

be

co

-located

with

other

transmitters.

578-100-127

Revision

C

Page

1

of

2

*578-100427C*

Intermec IV7 IV7 Declaration of Conformity

Intermec IV7 Manual

Intermec IV7 manual content summary: