Intermec PM43/PM43c PM43 Full Roll Rewinder Installation Instructions
Intermec PM43/PM43c Manual
View all Intermec PM43/PM43c manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PM43/PM43c manual content summary:
- Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 1
PM43 Full Roll Rewinder Installation Instructions - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 2
Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista Powered are either trademarks or registered trademarks of Intermec Technologies Corporation. There are U.S. and foreign patents as well as U.S. and foreign patents pending. ii PM43 Full Roll Rewinder Installation Instructions - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 3
Rewinder Use these instructions to install the full roll rewinder on the Intermec PM43 printer. You will need these tools to install the full roll rewinder: • #T20 Torx screwdriver • Small wrench. The full roll rewinder must only be installed by an authorized service technician. Follow standard - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 4
contains wires and components with dangerous voltage (up to 380 V). Make sure that the printer is switched off and the power cord is disconnected before the cover is removed. To open position. 4 Lower the media cover and lift it off the hinges. 4 PM43 Full Roll Rewinder Installation Instructions - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 5
To remove the electronics cover 1 Use a T20 Torx screwdriver to remove the two screws that secure the electronics cover to the inside of the printer base. 2 Use a T20 Torx screwdriver to remove the two screws located on the outside of the electronics cover. 3 Remove the electronics cover, and put - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 6
To install the full roll rewinder 1 Open the media access door and pull up on the ends of the door until it snaps off of the printer base. 2 Remove the three screws that connect the tear bar to the printer and remove it. (x3) 6 PM43 Full Roll Rewinder Installation Instructions - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 7
3 Remove the five screws that attach the printer spine to the base. Remove One Screw from the Media Side of Base (x2) (x2) Remove Four Screws from the Electronics Side of Base 4 Lift the spine away from the printer base. PM43 Full Roll Rewinder Installation Instructions 7 - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 8
5 Attach the spine to the full roll rewinder with the five screws removed in Step 3. Attach the Spine with One Screw on the Media Side (x2) (x2) Attach the Spine with Four Screws on the Electronics Side 8 PM43 Full Roll Rewinder Installation Instructions - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 9
6 Connect the grounding strap to the printer spine with one of the screws. Make sure the M4 serrated washer is located between the extrusion from then insert it into the RWNDR connector on the main logic board. 8 Replace the electronics cover. PM43 Full Roll Rewinder Installation Instructions 9 - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 10
9 Attach the batch plate with the three screws you removed from the tear bar in Step 2. (x3) 10 Replace the media cover. 11 Open the full roll rewinder door and move the media roll guide out to the edge of the base. 10 PM43 Full Roll Rewinder Installation Instructions - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 11
12 Raise the media roll guide to the upright position and insert the cardboard core onto the media roll rewinder hub. 13 Close the full roll rewinder door. 14 Close the media cover. PM43 Full Roll Rewinder Installation Instructions 11 - Intermec PM43/PM43c | PM43 Full Roll Rewinder Installation Instructions - Page 12
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2012 Intermec Technologies Corporation. All rights reserved. PM43 Full Roll Rewinder Installation Instructions *931-098-001* P/N 931-098-001
Full Roll Rewinder
PM
43
Installation Instructions