Intermec PM4i Cutter Kit (for EasyCoder PM4i) Installation Instructions
Intermec PM4i Manual
 |
View all Intermec PM4i manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PM4i manual content summary:
- Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 1
Installation Instructions Cutter Kit (for EasyCoder PM4i) - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 2
Intermec Printer AB Idrottsvägen 10 P.O. Box 123 S-431 22 Mölndal Sweden Service support: +46 31 869500 The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and/or service Intermec manufactured equipment and is not to be released, - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 3
Contents Preface Introduction iv Printer Firmware iv Installation Kit iv 1 Description General Information 2 Media 3 Measures and Weight 4 2 Physical Installation Installation Instructions 6 3 Fingerprint Control Activating the Cutter 10 Controlling the Cut Position 10 4 IPL - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 4
Preface Introduction This Installation Instructions booklet describes how to install a cutter in an EasyCoder PM4i printer. The installation instructions also describes how to control the cutter in Intermec Fingerprint and in Intermec Programming Language (IPL). Printer Firmware The printer must be - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 5
1 Description This chapter describes the cutter and provides essential technical data. Cutter Kit (EasyCoder PF4i-series) Installation Instructions 1 - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 6
factory-installed or field-installable option for the EasyCoder PM4i printer. The cutter automatically cuts off the media after printing according to instructions only operate when being completely closed. The cutter prevents an optional label taken sensor from working, even if it not necessary to - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 7
be careful not to cut through the labels themselves, because the adhesive will stick to the cutting blade and may cause malfunction. Avoid cutting soft plastic-based media. Minimum media thickness: 78µm Maximum media thickness: 175µm Cutter Kit (EasyCoder PF4i-series) Installation Instructions 3 - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 8
, the measures of the printer are: 150 mm (5.91 in.) 100 mm (3.94 in.) 154 mm (6.06 in.) 593 mm (23.35 in.) 747 mm (29.41 in.) 160 mm (6.30 in.) 644 mm (25.35 in.) The weight is increased by approximately 1.8 kg (4.0 pounds) 4 Cutter Kit (EasyCoder PF4i-series) Installation Instructions - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 9
2 Physical Installation This chapter describes how to physically install the cutter in an EasyCoder PM4i printer. Cutter Kit (EasyCoder PF4i-series) Installation Instructions 5 - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 10
Physical Installation Installation Instructions Install the cutter this way: • Turn the printer upside down on a soft piece of cloth or similar. • Remove the front door, which is held by two #T20 Torx screws. • Insert the cutter bracket between the printer's bottom plate and print mechanism so - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 11
3 Fingerprint Control This chapter describes how to control the cutter in an EasyCoder PM4i printer when running Intermec Fingerprint v8.00 (or later). Cutter Kit (EasyCoder PF4i-series) Installation Instructions 7 - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 12
position is controlled by the Feed Adjustment parameters in the Setup Mode or in setup files or setup strings. The following feed adjustment values are recommended for cutting: Type of Cutting 8 dots/mm printhead 11.81 dots/mm printhead Cut between labels w. gaps Start adjust: - 325 dots - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 13
4 IPL Control This chapter describes how to control the cutter in an EasyCoder PM4i printer when running IPL v2.00 (or later). Cutter Kit (EasyCoder PF4i-series) Installation Instructions 9 - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 14
The cutter is activated in the Setup Mode (Setup/Configuration/Cutter) or by the commands (cut) and c1 (enable cutter) or c0 (disable cutter). Application programs may have related facilities for operating the cutter. 10 Cutter Kit (EasyCoder PF4i-series) Installation Instructions - Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 15
- Intermec PM4i | Cutter Kit (for EasyCoder PM4i) Installation Instructions - Page 16
Intermec Printer AB Idrottsvägen 10, P.O. Box 123 S-431 22 Mölndal, Sweden tel +46 31 869500 fax +46 31 869595 www.intermec.com Cutter Kit (EasyCoder PM4i-series) Installation Instructions *1-960595-00* *1-960595-00*
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Installation
Instructions
Cutter Kit
(for EasyCoder PM4i)