Intermec PM4i PM4i RFID Kit Installation Instructions
Intermec PM4i Manual
 |
View all Intermec PM4i manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PM4i manual content summary:
- Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 1
Installation Instructions RFID Kit for the EasyCoder® PM4i Printer - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 2
Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista Powered are either trademarks or registered trademarks of Intermec Technologies Corporation. There are U.S. and foreign patents as well as U.S. and foreign patents pending. ii EasyCoder PM4i RFID Kit Installation Instructions - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 3
later). The latest firmware versions are always available for download at www.intermec.com. • A #T10 and a #T20 Torx screwdriver. • A straight-slot screwdriver. Installing the RFID Kit The kit comes either factory installed or can be installed on-site by an authorized service technician. Before you - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 4
power cord and communication cables are disconnected. I/O Interface Board with IM4 Radio Module Upper Media Guide with RFID Antenna Dual Slot I/O Cable M3x5 Screw (x2) M4x5 Screw Contents of Installation Kit Spacer Screw Real-Time Clock 2 EasyCoder PM4i RFID Kit Installation Instructions - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 5
To install the RFID kit 1 Open the printer's side door. 2 Turn the LSS adjustment screw counterclockwise to move the position of the Label Stop Sensor so that it does not obstruct the small hole leading into the electronics compartment. EasyCoder PM4i RFID Kit Installation Instructions 3 - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 6
. Loosen the edge guide and remove both items from the shaft. Upper Media Guide Edge Guide 4 Route the antenna connection cable through the opening in the center deck. Slide the new media guide (with antenna) and the edge guide onto the shaft. 4 EasyCoder PM4i RFID Kit Installation Instructions - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 7
screws that hold the electronics cover to the printer. 6 Put the printer back on its feet. Remove the four screws that hold the cover to the center section. Gently pull out the cover so the console cable can be disconnected from the CPU board. EasyCoder PM4i RFID Kit Installation Instructions 5 - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 8
the Dual Slot I/O cable to the main board before sliding the RFID interface board into one of the unoccupied slots in the rear of the printer. Note: You must use the first available slot starting from the left (slot 1). 6 EasyCoder PM4i RFID Kit Installation Instructions - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 9
the board in slot number 2, use the cable's second connector. 10 Secure the board with two screws in the printer's rear plate. You can use the two M3x5 screws supplied with the kit, or use the ones left over when you removed the cover plate. EasyCoder PM4i RFID Kit Installation Instructions 7 - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 10
. If you are installing in slot 1, you can use the spacer screw that comes pre-installed on the main board. If you are installing in slot 2, use the spacer screw supplied with the kit. 12 Connect the antenna cable to the jack on the radio module. 8 EasyCoder PM4i RFID Kit Installation Instructions - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 11
console cable to the CPU board while putting back the cover over the electronics compartment. 2 Fasten the four screws in the center deck. 3 Tip the printer over on its side. 4 Insert and fasten the screws in the empty holes in the bottom plate. EasyCoder PM4i RFID Kit Installation Instructions 9 - Intermec PM4i | PM4i RFID Kit Installation Instructions - Page 12
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com RFID Kit for the EasyCoder PM4i Printer Installation Instructions *931-041-001* P/N 931-041-001
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
RFID Kit
for the EasyCoder®
PM4i Printer
Installation
Instructions