Intermec PM4i RFID Kit (Gen 2, 869&915 MHz) Installation Instructions
Intermec PM4i Manual
 |
View all Intermec PM4i manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PM4i manual content summary:
- Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 1
Installation Instructions RFID Kit (Gen 2, 869/915 MHz) for the EasyCoder® PM4i Printer - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 2
Printer Network Manager, IRL, JANUS, LabelShop, Mobile Framework, MobileLAN, Nor*Ware, Pen*Key, Precision Print, PrintSet, RoutePower, SmartSystems, TE 2000, Trakker Antares and Virtual Wedge are either trademarks or registered trademarks of Intermec Technologies Corporation. Throughout this manual - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 3
can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 4
, Switzerland. Mölndal 2005-11-14 Per-Ove Jacobsson Site Manager 1 /. Intermec assumes no responsibility regarding the CE Directive if the printer is handled, modified, or installed in other manners than those described in the manuals. iv RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 5
Contents About These Instructions vi Printer Firmware Recommendations vi Limitations vi Contents of Installation Kit 1 Step-by-Step Instructions 2 RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 6
use in the EasyCoder PM4i printer only. The device is country/region specific and must be ordered for the correct country/region. Use of this device in other regions than shown on the device home page/test label may violate applicable law. vi RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 7
Contents of Installation Kit I/O Board Paper Guide with RFID Antenna and cable IM5 Reader Module IM5 Data Cable IM5 Power Cable Bracket assy RSMA/SMA to MMCX Adapter Cable Dual Slot I/O Bus Cable RFID Label Two Hexagon Lock Nuts Five MRT 4x6 Screws Two MRT 4x16 Screws Spacer Screw (20mm - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 8
Step-by-Step Instructions The installation described in this section must only be performed by an authorized service technician. Intermec assumes no responsibility for personal injury or damage to the equipment if the installation is performed by an unauthorized person. Take precautions against - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 9
1 Open the printer's side door. 2 Turn the LSS adjustment screw counterclockwise to move the position of the Label Stop Sensor so that it does not obstruct the small hole leading into the electronics compartment. RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 10
the support shaft. Loosen the edge guide and remove both items from the shaft. 4 Route the antenna connection cable through the opening in the center deck. Slide the replacement paper guide (with antenna) and the edge guide onto the shaft. RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 11
down on its side, electronic compartment facing down. Remove the six screws (A-F). Replace screws E and F with the M4x16 screws supplied with the installation kit. 6 Put the printer back on its feet. Remove the four screws that hold the cover to the center section. Gently pull out the cover so - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 12
3 Slide the I/O board halfway into the empty slot next to the printer's CPU board (1). Connect the two using the I/O bus cable (2). I/O board with two M3 screws in the printer's rear plate (4). Mark the I/O board with the RFID label (5). RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 13
a 10 mm spacer and the original screw (2). 9 Connect the IM5 data and power cables to the IM5 reader module. RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 14
tie to attach the loose end of the adapter cable to the side of the IM5 reader module. XZ RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 15
the printer over on its side. Insert and fasten the screws in the empty holes in the bottom plate. 3 Store remaining components (the original paper guide and other hardware that had to be removed prior to installation) for possible future use. RFID Kit (Gen 2, 869/915 MHz) Installation Instructions - Intermec PM4i | RFID Kit (Gen 2, 869&915 MHz) Installation Instructions - Page 16
Intermec Technologies Corporation Corporate Headquarters 6001 36th Avenue West Everett, WA 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com RFID Kit (Gen 2, 869/915 MHz) Installation Instructions *1-960654-01* P/N 1-960654-01
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Installation
Instructions
RFID Kit
(Gen 2, 869/915
MHz)
for the EasyCoder®
PM4i Printer