Intermec SG20 SG20T Tethered Scanner Compliance Insert

1

SG20T1D, SG20T2D, SG20T2DHC, SG20THP, SG20THPHC

Scanner Compliance Insert

Model SG20T

The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of

accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void

the compliance of this product and may result in the loss of the user’s authority to operate the equipment.

Laser Compliance and Precaution

The SG20T is registered with the CDRH as a Class II LASER Product (21 CFR Subchapter J, Part 1040). This product has a maximum output

of 1 mW at 650 nm.

Note: There are no controls or adjustments provided for routine operation or maintenance of the SG20T.

Laser and Imager Compliance and Precaution

This product complies with the following standards for laser and LED safety:

•

IEC 60825-1:2007/EN 60825-1:2007 : Class 2 (1 mW, 650 nm)

•

IEC 60825-1/EN 60825-1 - Class 1 LED Product (imaging options only, no laser label)

If applicable, this product will be provided with a set of laser safety labels illustrated on the last page (s) of this document. If the proper label

language is not installed on the device, locate and apply the appropriate label over the existing label.

敬告本产品的用户，请务必使用 Intermec Technologies Corporation 许可的附件和外围设备。如果使用推荐附件之外的其它附件，

或未经 Intermec Technologies Corporation 许可而擅自改装本产品，都可能会使本产品的符合性无效，并可能会导致用户失去操作

本设备的权利。

适用于中国用户

激光和成像器的合规性与安全防范

本产品符合下列有关激光和 LED 安全性的标准：

•

IEC 60825-1:2007/EN 60825-1:2007 : Class 2 (1 mW, 650 nm)

•

IEC 60825-1 / EN 60825-1 - Class 1 LED 产品 （仅提供成像选件，无激光标签）

Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future

reference.

Caution: There are no user serviceable parts inside the SG20T. Use of controls or adjustments, or performance of procedures other

than those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-670 nm

注意：该标记指示在使用之前用户应阅读所有包含的文档。请保留这份补充材料，以备日后参考。

元件名及有毒有害物质名称表

有毒有害物质名称

元件名

铅 (Pb)

汞 (Hg)

镉 (Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

电路板上的陶瓷元件和黄铜接头

X

O

O

O

O

O

塑料盖板上的黄铜嵌件

X

O

O

O

O

O

BeCu 连接器插脚

X

O

O

O

O

O

O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

Complies with 21 CFR 1040

with Laser Notice 50. This

device complies with

part 15 of the FCC Rules.

IEC 60825-1: 2007

EN 60825-1: 2007