Intermec SR31T SR31T Scanner Compliance Insert

1

SR31T Scanner Compliance Insert

Model 1017ST01

For Users in English-Speaking Regions (en)

Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories

other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the

compliance of this product and may result in the loss of the user’s authority to operate the equipment.

For Users in the U.S.A. and Canada

Laser Compliance and Precaution

The 1017ST01 HP configuration is registered with the CDRH as a Class II LASER Product (21 CFR Subchapter J, Part 1040). This product has

a maximum output of 1 mW at 650 nm.

Note: There are no controls or adjustments provided for routine operation or maintenance of the 1017ST01.

Imager Compliance and Precaution

This product complies with IEC 62471: 2006-07 for LED safety.

The scan engine mounted in 1D and 2D configurations are classified as: Exempt.

The scan engine mounted in HP configuration is classified as: Risk group 1.

•

Exempt: No photobiological hazards based on the limits defined in the standard.

•

Risk group 1: Low-risk—does not pose a hazard based on normal behavorial limitations on exposure.

U.S.A. Digital Emissions Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the radio or television receiving antenna.

•

Increase the separation between the computer equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.

•

Consult the dealer or an experienced radio television technician for help.

Canadian Digital Apparatus Compliance

This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired

operation.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations ICES-003.

For Users in Europe

Imager Compliance and Precaution

LASER Safety—IEC 60825-1: 2007/EN 60825-1: 2008-05: Class 2 (1 mW, 650 nm) - applies to HP configuration only.

If applicable, this product will be provided with a set of laser safety labels illustrated on the last page of this document. If the proper label

language is not installed on the device, locate and apply the appropriate label over the existing label.

LED Safety—IEC 62471: 2006-07/EN62471: 2008: The scan engine mounted in 1D and 2D configurations are classified as: Exempt. The scan

engine mounted in HP configuration is classified as: Risk group 1.

•

Exempt: No photobiological hazards based on the limits defined in the standard.

•

Risk group 1: Low-risk—does not pose a hazard based on normal behavorial limitations on exposure.

Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future

reference.

Caution: There are no user serviceable parts inside the 1017ST01. Use of controls or adjustments, or performance of procedures

other than those specified herein, may result in hazardous laser light exposure of up to 1 mW at 650 nm.

Complies with 21 CFR 1040 with

Laser Notice 50. This device complies

with part 15 of the FCC Rules.

IEC 60825-1: 2007

EN 60825-1: 2007