Intermec SR61 SR61T Compliance Insert

1

SR61T Compliance Insert

For Users in the United States and Canada

The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of

accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void

the compliance of this product and may result in the loss of the user’s authority to operate the equipment.

FCC Digital Emissions Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the radio or television receiving antenna.

•

Increase the separation between the computer equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.

•

Consult the dealer or an experienced radio television technician for help.

Canadian Digital Apparatus Compliance

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Conformité aux normes canadiennes sur les appareils numériques

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.

Laser Compliance and Precaution

The SR61T

is registered with the CDRH as a Class II Laser Product (21 CFR Subchapter J, Part 1040). This product has a maximum output of

1 mW at 630-680 nm.

Note: There are no controls or adjustments provided for routine operation or maintenance of the SR61T.

For Users Outside of the United States or Canada

Laser and Imager Compliance and Precaution

This product complies with the following standards for laser and LED safety:

•

IEC 60825-1 / EN 60825-1 - Class 2 (1 mW, 630-680 nm)

•

IEC 60825-1 / EN 60825-1 - Class 1 LED Product (imaging options only, no laser label)

This product is provided with a set of laser safety labels illustrated on page 5 of this guide. If the appropriate label is not installed on the device,

locate the sheet of labels that was shipped with your device and place the appropriate label over the existing label.

Caution: This marking indicates that the user should read all included documentation before use.

Attention: Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse.

Caution: For power supply, use Intermec Model AE26. No user-serviceable parts.

Attention: Pour la source d’alimentation, utilisez Intermec modèle AE26. Il ne contient aucune pièce réparable par l’utilisateur.

Caution: There are no user serviceable parts inside the SR61T. Use of controls or adjustments, or performance of procedures

other than those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-680 nm.

Attention: La SR61T ne contiennent pas de pièces révisibles par l’utilisateur. L’utilisation de contrôles ou d’ajustements ou

l’exécution de procédures autres que celles spécifiées ici peuvent mener à l’exposition à de la lumière laser hasardeuse de plus de

1 mW à 630-680 nm.

Caution: This marking indicates that the user should read all included documentation before use.

Caution: For power supply, use Intermec Model AE26. No user-serviceable parts.

ATTENTION

Conforms with USA DHHS 21 CFR

Subchapter

ATTENTION

CAUTION