Invacare 9153642053 Owners Manual
Invacare 9153642053 Manual
 |
View all Invacare 9153642053 manuals
Add to My Manuals
Save this manual to your list of manuals |
Invacare 9153642053 manual content summary:
- Invacare 9153642053 | Owners Manual - Page 1
's Operator and Maintenance Manual Pronto® M51™and M61™with SureStep® DEALER: This manual MUST be given to the user of the product. USER: BEFORE using this product, read this manual and save for future reference. For more information regarding Invacare products, parts, and services, please visit www - Invacare 9153642053 | Owners Manual - Page 2
. REFERENCE DOCUMENTS DOCUMENT M50/M51/M61 Service Manual MK5™NX™Electronics Manual (M51 Wheelchairs) MK6i™Electronics Field Reference Guide (M61 Wheelchairs) PART NUMBER 1125075 1110532 1141471 NOTE: Updated versions of this manual are available on www.invacare.com. Pronto® M51™and M61™with - Invacare 9153642053 | Owners Manual - Page 3
21 Reaching and Bending - Backward ...22 SECTION 4-SAFETY INSPECTION/TROUBLESHOOTING 23 Safety Inspection Checklists...23 Troubleshooting Guide ...25 Checking Battery Charge Level...28 SECTION 5-WHEELCHAIR OPERATION 29 Operating the Wheelchair...29 Adjusting the Speed ...30 Using the Horn...31 - Invacare 9153642053 | Owners Manual - Page 4
Rigging Supports 51 Walker servicing of your product. 3. Receiving updates with product information, maintenance tips and industry news. Register ONLINE at warranty.invacare Invacare Corporation and protected as required by applicable laws and regulations. Pronto® M51™and M61™with SureStep® 4 Part - Invacare 9153642053 | Owners Manual - Page 5
SPECIAL NOTES Signal words are used in this manual and apply to hazards or unsafe practices which THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. WHEELCHAIR USER As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user. - Invacare 9153642053 | Owners Manual - Page 6
from other chairs previously used. This power wheelchair has Invacare's SureStep technology, a feature that this wheelchair. Other general warnings listed within this document also apply. Wheelchairs should by corrosion should be replaced IMMEDIATELY. Wheelchairs that are used by incontinent users - Invacare 9153642053 | Owners Manual - Page 7
LABEL LOCATION LABEL LOCATION M51 Wheelchairs Serial label located inside the wheelchair frame M61 Wheelchairs Part No 1125085 7 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 8
Up, Depth and Height Adjustable, Footboard, Swingaway Front Rigging, Elevating Legrest 145 to 170 lbs 192 to 217 lbs Pronto® M51™and M61™with SureStep® 8 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 9
their unique conditions impact their individual results. Users should become familiar with the battery discharge indicator on the joystick to determine the range of their wheelchair. Refer to Battery Charger Operation on page 67 for more information about the battery discharge indicator - Invacare 9153642053 | Owners Manual - Page 10
Service Set‐up of the Electronic Control Unit is to be performed only by a qualified technician. The final adjustments of the controller may affect other activities of the wheelchair combustible materials. Contact your oxygen supplier for instruction in the use of oxygen. Operation Information - Invacare 9153642053 | Owners Manual - Page 11
or disengage the motor release levers until the power is in the Off position. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the Off position. Avoid storing or using the wheelchair near open flame or combustible products. Serious injury - Invacare 9153642053 | Owners Manual - Page 12
in this manual are based on the use of deep cycle gel cell or sealed lead acid batteries. Invacare strongly recommends their use as the power source for this unit. Carefully read battery/battery charger information prior to installing, servicing or operating your wheelchair. Charging Batteries - Invacare 9153642053 | Owners Manual - Page 13
Instructions DO NOT, under any circumstances, cut or remove the round grounding prong from any plug used with or for Invacare products addition, Invacare has placed RED/ORANGE warning tags on some equipment. DO NOT remove these tags. Rain Test Invacare has tested its power wheelchairs in accordance - Invacare 9153642053 | Owners Manual - Page 14
POWERED WHEELCHAIR. Electromagnetic Interference (EMI) From Radio Wave Sources Powered wheelchairs and motorized scooters (in this text, both will be referred to as powered wheelchairs likely to cause EMI problems to your powered wheelchair. Pronto® M51™and M61™with SureStep® 14 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 15
powered wheelchairs and motorized scooters. FOLLOWING THE WARNINGS LISTED BELOW SHOULD REDUCE THE CHANCE OF UNINTENDED BRAKE RELEASE OR POWERED WHEELCHAIR the electronics of this wheelchair as manufactured by Invacare may adversely affect the EMI immunity levels. Part No 1125085 15 Pronto® - Invacare 9153642053 | Owners Manual - Page 16
only as a "basic" guide. The techniques that are discussed on the following pages have been used successfully by many. Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual. Invacare recognizes and encourages each - Invacare 9153642053 | Owners Manual - Page 17
WHEELCHAIRS wheelchair user to reach, bend and transfer in and out of the wheelchair wheelchair wheelchair manage your wheelchair. Keep in problem. The chair cannot reverse over the bump at this point. Continue forward and then turn around. While the wheelchair will cause wheelchair to feel unstable - Invacare 9153642053 | Owners Manual - Page 18
or traversing curbs or other impediments. Also, be aware of detachable parts such as arms or legrests. These must NEVER be used to move the wheelchair or as lifting supports, as they may be inadvertently released, resulting in possible injury to the user and/or assistant(s). When learning a new - Invacare 9153642053 | Owners Manual - Page 19
when it is necessary to move an unoccupied power wheelchair up or down the stairs. Invacare recommends using two assistants and making thorough preparations. Use only secure, nondetachable parts for hand-hold supports. It is strongly recommended to lift the wheelchair only by the rear frame and the - Invacare 9153642053 | Owners Manual - Page 20
as hand hold supports, transfer the wheelchair base to desired location. Refer to FIGURE 3.4. 7. Using non‐removable (nondetachable) parts, transfer the a wheelchair between floors. Serious bodily injury may occur. Transferring To and From Other Seats ƽ WARNING ALWAYS turn the wheelchair power Off - Invacare 9153642053 | Owners Manual - Page 21
you are transferring, with the rear casters pointing away from it. 2. After the wheelchair is positioned properly for transfer, verify that the motor release levers are engaged. Refer to FIGURE 3.6 Reaching, Leaning and Bending - Forward Part No 1125085 21 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 22
to tip over. NOTE: For this procedure, refer to For this procedure, refer to FIGURE 3.7. Position wheelchair as close as possible to the desired object. Point the front AND rear casters rearward to create the Reaching and Bending - Backward Pronto® M51™and M61™with SureStep® 22 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 23
SECTION 4-SAFETY INSPECTION/ TROUBLESHOOTING NOTE: Every six months or as necessary take your wheelchair to a qualified dealer for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair. To operate properly and - Invacare 9153642053 | Owners Manual - Page 24
TROUBLESHOOTING Inspect/Adjust Weekly ❑ Seat is secured to wheelchair any loose hardware on the wheelchair. ❑ Inspect seat positioning strap Inspect/Adjust Periodically ❑ Ensure wheelchair rolls straight (no excessive drag and armrests. ❑ Inspect charger AC power cord for damage. Replace if necessary. - Invacare 9153642053 | Owners Manual - Page 25
speed when seat is in elevated position. Troubleshooting Guide NOTE: For additional troubleshooting information and explanation of error codes, refer to the Electronics Manual supplied with each wheelchair. All Wheelchairs General Troubleshooting SYMPTOM Limited driving distance. PROBABLE CAUSE - Invacare 9153642053 | Owners Manual - Page 26
. Contact Dealer/Invacare. Contact Dealer/Invacare. Contact Dealer/Invacare for service. Engage motor lock. Contact Dealer/Invacare for service. Reprogram controller (Refer to electronics manual supplied with wheelchair). Have terminals cleaned. Contact Dealer/Invacare for service. About Joystick - Invacare 9153642053 | Owners Manual - Page 27
TROUBLESHOOTING of-Neutral-at-Power-Up to Neutral. mode. Service Indicator Light Invacare/Dealer for service. Contact Invacare/Dealer for service. Contact Invacare/Dealer for service. Contact Invacare/Dealer for service. Wrong type of remote connected. Contact Invacare/Dealer for service. Part - Invacare 9153642053 | Owners Manual - Page 28
TROUBLESHOOTING Additional Troubleshooting Information for M61 Wheelchairs SYMPTOM Wheelchair manual and any service information that accompanies a battery and charger before operating the wheelchair. Move the wheelchair to a work area before opening battery box or installing service Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 29
by pressing the On/Off button. On/Off Button FIGURE 5.1 Turning the Power On/Off Using the Joystick to Drive the Wheelchair ƽ WARNING DO NOT operate wheelchair on an incline while in an elevated position. Otherwise, the wheelchair may tip over and injury or damage may occur. NOTE: For this - Invacare 9153642053 | Owners Manual - Page 30
and stop smoothly. To drive the wheelchair, perform the following: 1. Adjust speed control knob to the appropriate setting. 2. Turn the power On. Refer to Turning the Power On/Off on page 29. 3. bars in the speedometer will light. Pronto® M51™and M61™with SureStep® 30 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 31
or property damage. If such devices are used, Invacare shall not be liable and the limited warranty is wheelchair by 80%. If the wheelchair operates at maximum speed while in an elevated position, DO NOT operate the wheelchair. Have the wheelchair serviced immediately by a qualified technician. Part - Invacare 9153642053 | Owners Manual - Page 32
For this procedure, refer to FIGURE 5.5 on page 32. NOTE: This procedure applies to M61 wheelchairs only. 1. Make sure the wheelchair is on a level surface. 2. Press the mode button to switch from driving mode to elevate 5.5 Elevating the Seat Pronto® M51™and M61™with SureStep® 32 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 33
SECTION 5-WHEELCHAIR OPERATION SPJ+ and SPJ+ w/ACC Joystick Switches and Indicators NOTE: For the ) Joystick DETAIL "A" FRONT VIEW Charger/ Programming Input Service Indicator FIGURE 5.6 SPJ+ and SPJ+ w/ACC Joystick Switches and Indicators Part No 1125085 33 Pronto® M51™and M61™with SureStep - Invacare 9153642053 | Owners Manual - Page 34
limit mode limits the drive speed to a pre‐ programmed value, typically when the seat has been elevated and the wheelchair is required to drive at 20% speed. Speed Control Buttons The speed control buttons (tortoise button ( ) and on page 31. Pronto® M51™and M61™with SureStep® 34 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 35
occurs. Refer to Service Indicator Light Diagnostics on page 27 for a listing of the flash codes and what they indicate. Information Gauge Display Located on the front of the joystick housing, it provides the following information to the user on the status of the wheelchair ‐ 1. Power is on. 2. True - Invacare 9153642053 | Owners Manual - Page 36
any maintenance, adjustment or service verify that On/Off switch overall width of the wheelchair. Ensure that there is to the arm support tube. 2. Remove the arm from the arm support tube. 3. If necessary support tube. NOTE: Changing the width of the arms may also affect the overall width of the wheelchair - Invacare 9153642053 | Owners Manual - Page 37
screw that secures the armrest to the seat frame assembly and tighten securely. Height Adjustment Holes Armrest Lock Knob Arm Frame Assembly FIGURE 6.4 Adjusting Height Part No 1125085 37 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 38
armrest into the arm sockets. Installing 1. Slide the flip back armrest into the arm sockets on the wheelchair frame. 2. Install the quick release pin through the rear arm socket and flip back armrest. 3. /Removing Flip Back Armrests Pronto® M51™and M61™with SureStep® 38 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 39
. Height Adjustment Lever Flip Back Armrest Height Adjustment Lever Locked (Vertical) Unlocked (Horizontal) Armrest Release Lever Front Arm Socket FIGURE 6.6 Positioning/Adjusting Flip Back Armrests Part No 1125085 39 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 40
is tightened securely - otherwise injury or damage may result. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the Off position. Adjusting the Back Angle same back angle setting. Pronto® M51™and M61™with SureStep® 40 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 41
7.3. 1. To raise the headrest, lift the headrest up to the desired position. 2. To lower the headrest, push the release tab towards the front of the wheelchair. Lower the headrest to the desired position. Headrest Release Tab Headrest Tube FIGURE 7.3 Adjusting the Headrest (Semi-Recline Only - Invacare 9153642053 | Owners Manual - Page 42
seat installs the same way. NOTE: ASBA Seat installs the same way. FIGURE 7.4 Removing/Installing the Seat Assembly Pronto® M51™and M61™with SureStep® 42 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 43
Strap Mounting Screws NOTE: Office style van seat is shown. Standard van seat adjusts the same way. FIGURE 7.5 Replacing the Seat Positioning Strap - Van Seat Part No 1125085 43 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 44
Seat Frame Quick Release Pin Tab Seat Rail Spacer Locknut FIGURE 7.6 Replacing the Seat Positioning Strap - ASBA Seat Pronto® M51™and M61™with SureStep® 44 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 45
injury or damage may result. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the Off the wheelchair frame by depressing the button while sliding the pin out. 2. Remove the footboard assembly from the wheelchair frame. Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 46
result. Keep detent balls clean. 1. Position the footboard assembly onto the wheelchair frame so that the mounting hole in the wheelchair frame aligns with the desired mounting hole in the footboard assembly. 2. the mounting screw in place. Pronto® M51™and M61™with SureStep® 46 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 47
-release pin are fully released and beyond the outer edge of the tube before operating the wheelchair. Otherwise, injury and/or damage may result. Keep detent balls clean. 2. Adjust footboard 8.3 Adjusting the Footboard Assembly - Depth Part No 1125085 47 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 48
locks into place. NOTE: The footplate will be on the inside of the wheelchair when locked in place. 5. Repeat STEPS 1‐4 for opposite side of wheelchair. Hinge Pins Telescoping Front Rigging Support Front Rigging Release Lever Front Rigging Hinge Plate FIGURE 9.1 Installing/Removing Front Riggings - Invacare 9153642053 | Owners Manual - Page 49
footrest(s) onto the wheelchair. Refer to Installing/Removing Front Riggings on page 48. 8. Reinstall any accessories onto the footrest(s). Locknut Coved Washer Footrest Support Coved Washer Hex Bolt Lower Footrest FIGURE 9.2 Adjusting Footrest Height - Model PHWH93 Part No 1125085 49 Pronto - Invacare 9153642053 | Owners Manual - Page 50
bolt and locknut that secure the lower footrest to the footrest support. 4. Repeat STEPS 1‐3 for the opposite side of the wheelchair footrest, if necessary. Lower Footrest FIGURE 9.3 Adjusting Footrest Height until the spacer is secure. Pronto® M51™and M61™with SureStep® 50 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 51
appropriate mounting hole of the telescoping front rigging support with the front mounting hole in the seat frame tubes to achieve the desired depth as shown in FIGURE 9.6. NOTE: The footplate will be on the inside of the wheelchair when locked in place. Part No 1125085 51 Pronto® M51™and M61 - Invacare 9153642053 | Owners Manual - Page 52
support to the seat frame as shown in FIGURE 9.6. 5. If necessary, repeat STEPS 2‐4 on remaining telescoping front rigging support Bolts Seat Telescoping Front Rigging Support Hinge Locknuts Spacers Inner Mounting Rigging Supports - Office Style Seat Pronto® M51™and M61™with SureStep® 52 - Invacare 9153642053 | Owners Manual - Page 53
to achieve the desired depth as shown in FIGURE 9.7. • Replacing ‐ i. Remove the existing telescoping front rigging support from the wheelchair frame. ii. Insert the new telescoping front rigging support into the seat frame. iii. Align the appropriate mounting hole of the telescoping front rigging - Invacare 9153642053 | Owners Manual - Page 54
telescoping front rigging support to one of three depth positions. • Remove existing telescoping front rigging. 3. Secure telescoping front rigging at desired depth with existing two mounting screws, spacers, and locknuts. Securely tighten. Pronto® M51™and M61™with SureStep® 54 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 55
: The two telescoping front rigging supports can be positioned at different depths depending on the need of the user. Mounting Screws Spacer Locknut Spacer Locknut Telescoping Front Tube FIGURE 9.8 Adjusting/Replacing Telescoping Front Rigging Supports - ASBA Seat Part No 1125085 55 Pronto - Invacare 9153642053 | Owners Manual - Page 56
injury or damage may result. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the frame and push downward to engage the hook and loop straps. 3. M61 Wheelchairs Only ‐ Secure the joystick cable using the clip on the top shroud. Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 57
levers are fully engaged before driving the wheelchair NOTE: For this procedure, refer to FIGURE allows an attendant to maneuver the wheelchair without power. 1. Locate the motor release Push the motor lock handles towards the front of the wheelchair (drive position). NOTE: This allows the motors to - Invacare 9153642053 | Owners Manual - Page 58
locknut (FIGURE 10.3). Securely tighten. Locknut Mounting Screw Washer Washer Caster FIGURE 10.3 Replacing Front/Rear Caster Assemblies Pronto® M51™and M61™with SureStep® 58 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 59
tighten caster journal system and guard against flutter, perform the following check: A. Tip back the wheelchair. B. Pivot both forks and casters to top of their arc simultaneously. C. Let casters drop Washer FIGURE 10.4 Adjusting Forks Part No 1125085 59 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 60
service and before use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result. Make sure power to the wheelchair is Off before performing this section. The use of rubber gloves is recommended when working with batteries. Invacare ® 60 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 61
will not spill. It also helps to prolong the life of the battery. DO NOT tip the batteries. Keep the batteries in an upright position. Part No 1125085 61 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 62
-INCH (6PT) BOX WRENCH 1 DIAGONAL CUTTERS 1 Not Supplied Not Supplied Removing 1. Place the wheelchair in a well ventilated area where work can be performed without risking damage to carpeting or floor the Seat Assembly on page 57. Pronto® M51™and M61™with SureStep® 62 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 63
. Top Shroud BLACK Battery Connectors Rear Battery Joystick Cable Rear of Wheelchair Wheelchair Base Frame Battery Handle RED Battery Connectors BLACK Controller Connector Plug into of rubber gloves is recommended when working with batteries. Part No 1125085 63 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 64
[use tie‐wraps 11‐1/2‐inches long] (Detail "B" of FIGURE 11.3). 5. Position the batteries into the wheelchair. Refer to Removing/Installing Batteries from/ into Battery Tray on page 61. NOTE: New batteries MUST be Charging Batteries on page 66. Pronto® M51™and M61™with SureStep® 64 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 65
Controller U1 Battery Tie-wraps BLACK Connectors NOTE: Handles on batteries removed for clarity. U1 Batteries FIGURE 11.3 Connecting/Disconnecting Battery Cables Plug into controller Part No 1125085 65 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 66
the wheelchair at the same time. DO NOT attempt to recharge the batteries when the wheelchair batteries when the wheelchair is outside. DO NOT sit in the wheelchair while recharging the the individual instructions for each charger (supplied or purchased). If charging instructions are not supplied - Invacare 9153642053 | Owners Manual - Page 67
using the wheelchair. Basic concepts instructions are not supplied, consult a qualified technician for proper procedures. NEVER leave the charger unattended when the charger circuit breaker is tripping. Ꮨ DANGER Use of improper extension cord could result in risk of fire and electric shock. Part - Invacare 9153642053 | Owners Manual - Page 68
the male connector of the AC power cord from the wall outlet and then unplug the female connector of the AC power cord from the AC receptacle on the charger. ƽ WARNING DO NOT operate wheelchair with AC power cord attached to the wheelchair. Pronto® M51™and M61™with SureStep® 68 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 69
on AC Power Cord (Connects to AC Receptacle on Charger) Male Connector on AC Power Cord (Connects instructions for each charger (supplied or purchased). If charging instructions Only use a charger approved by Invacare when charging through the joystick on this wheelchair model. DO NOT use an - Invacare 9153642053 | Owners Manual - Page 70
independent charger is NOT supplied with the wheelchair. 1. Attach the battery charger connector to the charger port on the front of the joystick. 2. Plug the charger's AC power cord or extension into the grounded 110 Plugged Into The Joystick Pronto® M51™and M61™with SureStep® 70 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 71
securely - otherwise injury or damage may result. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the Off position. Removing/ to Disconnecting/Connecting the Joystick on page 74. Part No 1125085 71 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 72
lever to release the joystick mounting tube from the mounting bracket. 2. Remove the joystick from the wheelchair. 3. Remove the three hex mounting screws, spacers and locknuts that secure the mounting bracket to the on the opposite arm frame. Pronto® M51™and M61™with SureStep® 72 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 73
release the adjustment lock from joystick mounting tube. 2. Remove the joystick mounting tube from the wheelchair. 3. Remove the three hex screws that secure joystick mounting bracket, the threaded hole half does not fit over tube, rotate 180°. Part No 1125085 73 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 74
joystick connector with one hand and the controller connector on the wheelchair in the other and disconnect them by pulling them apart. Connecting of the joystick connector with one hand and the controller connector on the wheelchair in the other and align them. 2. Lightly push to engage the - Invacare 9153642053 | Owners Manual - Page 75
Joystick Cable SECTION 12-ELECTRONICS Joystick Office Style Seat Controller Connector Light Grey Collar Joystick Connector FIGURE 12.4 Disconnecting/Connecting the Joystick Part No 1125085 75 Pronto® M51™and M61™with SureStep® - Invacare 9153642053 | Owners Manual - Page 76
damage may result. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the the seat significantly increases the length of the wheelchair. When turning the wheelchair or swiveling the wheelchair seat, it is important to take note 76 Part No 1125085 - Invacare 9153642053 | Owners Manual - Page 77
anything other than its intended purpose of supporting an oxygen cylinder - otherwise, injury or damage may occur. DO NOT attempt to modify the oxygen holder to fit any other type of wheelchair. The oxygen holder was designed specifically for Invacare wheelchairs only. The installation of the oxygen - Invacare 9153642053 | Owners Manual - Page 78
Holder ƽ INSTALLATION WARNINGS After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely. The installation of the walker holder onto the back of the wheelchair seat increases the length of the wheelchair up to nine inches. When turning the - Invacare 9153642053 | Owners Manual - Page 79
'S CONTROL, AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS. A CHANGE IN OPERATING NOISE, PARTICULARLY RELATIVE TO MOTORS AND GEARBOXES DOES NOT CONSTITUTE A FAILURE - Invacare 9153642053 | Owners Manual - Page 80
SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS. A CHANGE IN are owned by or licensed to Invacare Corporation unless otherwise noted. ©2008 Invacare Corporation Part No 1125085 Rev J - 10/08
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
 |
 |
Owner’s Operator and Maintenance Manual
DEALER:
This manual MUST be given to
the user of the product.
USER:
BEFORE using this product, read this
manual and save for future reference.
For more information regarding
Invacare products, parts, and services,
please visit www.invacare.com
Pronto
®
M51
™
and
M61
™
with SureStep
®