Jensen JPA285 Quick Start Guide
Jensen JPA285 - Amplifier Manual
 |
UPC - 043258301284
View all Jensen JPA285 manuals
Add to My Manuals
Save this manual to your list of manuals |
Jensen JPA285 manual content summary:
- Jensen JPA285 | Quick Start Guide - Page 1
Start Guide Need help? For technical assistance, call the Jensen customer support line at 1-800-323-4815. L RCA Cable R Remote / Power Antenna Turn-on Wire 300 WATTS PEAK POWER MOSFET POWER SUPPLY BRIDGED +L- - R+ CAR STEREO / SOURCE UNIT SPEAKERS (+) JPA250 2 / 1 CHANNEL AMPLIFIER AMP - Jensen JPA285 | Quick Start Guide - Page 2
Jensen al 1-800-323-4815. L Cable RCA R 300 WATTS PEAK POWER MOSFET POWER SUPPLY BRIDGED +L- - R+ ESTÉREO DEL AUTOMÓVIL / UNIDAD FUENTE Cable de Encendido de Antena de Potencia/Remoto ALTAVOCES (+) JPA250 2 / 1 CHANNEL AMPLIFIER AMP de la instalación. 3. Instale el amplificador en una - Jensen JPA285 | Quick Start Guide - Page 3
appelez le soutien client Jensen à 1-800- 323-4815. L Câble RCA R 300 WATTS PEAK POWER MOSFET POWER SUPPLY BRIDGED +L- - R+ STEREO VOITURE /INSTALLATION DE SOURCE Fil de temps de fermeture d'antenne / Puissance/A distance HAUT-PARLEURS (+) JPA250 2 / 1 CHANNEL AMPLIFIER AMP +12V REM GND
-
1 -
2 -
3
 |
 |
1.
Disconnect the negative (-) battery terminal.
NOTE: Check your vehicle's owner's manual before disconnecting the battery.
Disconnecting the battery in some vehicles may require an anti-theft code when
reconnecting for stereo operation.
Some vehicles may run rough after reconnecting
the battery and require service to have the on-board computer reset. Check with
your local dealer if you are uncertain.
2.
Run suitable AWG wire to where the amplifier will be mounted (run 1 foot extra than
you think you will need). Use rubber grommets where wires will pass through the
firewall or other areas of the vehicle. Make certain a fuse holder is placed within 18
inches of the vehicle battery
–
this is mandatory. Do not place a fuse in the fuse
holder at the battery at this time.
3.
Mount the amplifier on a flat surface. Since a flat surface in a modern vehicle is often
difficult to find, an alternative is to cut a piece of 1/2 inch wood slightly larger than
the amplifier mounting area (covered with automotive type carpeting). Mount the
piece of wood, and then mount the amplifier to the carpeted wooden mount.
4.
Ground the amplifier using the same AWG wire size used for the power cable. Make
sure the ground location is a clean, unpainted metal surface.
5.
Run the RCA and Remote turn-on lead to the amplifier from the head unit.
6.
Run speaker wires (16 AWG or larger) from your speakers to the amplifier.
7.
Place a suitable size fuse in the fuse holder at the battery.
8.
Ensure that the input level control is set to "MIN".
9.
Turn on the head unit and make appropriate amplifier adjustments.
JPA260/JPA285 2-Channel Amp Quick Start Guide
Need help?
For technical assistance, call
the Jensen customer
support line at 1-800-323-4815.
L
R
Fuse Block or Fuse Holder
Minimum Wire Size:
+12V - 8 AWG
Ground - 8 AWG
CHASSIS GROUND
(
+
)
BATTERY
-
()
Remote /
Power Antenna
Turn-on Wire
RCA Cable
CAR STEREO /
SOURCE UNIT
SPEAKERS
( )
( )
(+)
(+)
AMP
BRIDGED
L
R
+
-
-
+
GND
+12V
REM
JPA250
300 WATTS
PEAK POWER
MOSFET POWER SUPPLY