Kenmore 9875 Owners Manual
Kenmore 9875 - 24 in. Laundry Center Manual
 |
View all Kenmore 9875 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenmore 9875 manual content summary:
- Kenmore 9875 | Owners Manual - Page 1
Owner's Manual and Installation Instructions ® 24-Inch Wide LAUNDRY CENTER Washer • Gas Dryer t----- I i .,,J IMPORTANT: Read and follow all safety and operating instructions before first use of this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PART NO. 3405594 PRINTED IN - Kenmore 9875 | Owners Manual - Page 2
WARNING: For your safety the informationin this manual must be followed to minimizethe risk of fire Follow the gas supplier's instructions. • If you cannot reachyourgas supplier,callthe fire department. Installation and service must be performedby a qualified installer,service agency,or the gas - Kenmore 9875 | Owners Manual - Page 3
34 OPERATING INSTRUCTIONS - DRYER 40 LAUNDRY TIPS 44 REMOVING STAINS 47 CARING FOR YOUR LAUNDRY CENTER 50 TROUBLESHOOTING - WASHER 54 TROUBLESHOOTING - DRYER 58 SEARS MAINTENANCE AGREEMENT 60 Please read this manual. It will help you install and operate your new Kenmore Laundry Center - Kenmore 9875 | Owners Manual - Page 4
this laundry center is installed and operated according to the instructions in this manual, Sears will repair or replace any of its mechanical effective for only 90 days. Warranty Service Warranty service is available by contacting your nearest Sears Service Center in the United States. This - Kenmore 9875 | Owners Manual - Page 5
not tamper with controls. • Do not repair or replace any part of the laundry center or attempt any servicing unless specifically recommended in the Owner's Manual or in published userrepair instructions that you understand and have the skills to carry out. • Do not use fabric softeners or products - Kenmore 9875 | Owners Manual - Page 6
INSTALLATION OVERVIEW For a complete list of tools and parts needed, see pages 6-12. A. SELECT LOCATION FOR YOUR LAUNDRY CENTER (pgs. 14-19) Laundry Tub Drain System (p. 15) Standpipe Drain System (p. 16) Floor Drain System (p. 16) Recessed Area/Closet Installation Instructions (pgs. 17-18) - Kenmore 9875 | Owners Manual - Page 7
B. INSTALL LEVELING LEGS (p. 20) [ o E Parts Needed: (supplied with laundry center) 2 rear leveling legs 2 front leveling legs C. REMOVE STYROFOAM PACKING (p. 20) Yellow card - Kenmore 9875 | Owners Manual - Page 8
D. CONNECT DRAIN HOSE (pgs. 21-22) Tools Needed: PUSH Parts Needed: (supplied with laundry center) Pliers that open _"_'- _-_ to 19/1_inches ! Flashlight (optional depending on installation) 1 yellow, single-wire hose clamp (top of drain hose) 1 silver, doublewire hose clamp (bottom of drain - Kenmore 9875 | Owners Manual - Page 9
F. CONNECT INLET HOSES TO WATER FAUCETS (p. 23) Tools Needed: Pliers that open to19"o inches _!_'OR _J Parts Needed: (supplied with laundry center) 2 water inle_ Bucket (optional depending on installation) Flashlight (optional depending on installation) G. SECURE CABLE BRACKET (p. 24) - - Kenmore 9875 | Owners Manual - Page 10
14.SECURE DRAIN HOSE (p. 24) Tools Needed: Parts Needed: (suppliedwith laundry center) Flashlight (optional depending on installation) I. LEVEL LAUNDRY CENTER (p. 25) Plastic strap Tools Needed: (_ open-%ened-incwhrench _Level Flashlight (optional depending on installation) Wood block 10 - Kenmore 9875 | Owners Manual - Page 11
J. INSTALL GAS LINE (pgs. 25-27) Tools Needed: Parts Needed: Do not use pipe joint compound Use pipe joint compound 8-inch or 10-inch pipe wrench Pipe joint compound resistant to LP. gas 3/8-inch male pipe flare (optional depending on installation) 1/2-inch to 3/8-inch pipe reducer - Kenmore 9875 | Owners Manual - Page 12
K. CONNECT EXHAUST (pgs. 28-32) | E Tools Needed: Parts Needed: Tin snips Flashlight (optional depending on installation) Flat-bladed screwdriver 4-inch rigid or flexible heavy metal vent 4-inch metal elbow(s) (optional depending on installation) ©0 ©0 4-inch outlet exhaust hood (4) 4- - Kenmore 9875 | Owners Manual - Page 13
into a grounded 3-prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire,, or electrical shock. • A 1?.0-volt, 60-Hz., AC-only, 15- or 20-ampere fused electrical supply is required. • A time-delay - Kenmore 9875 | Owners Manual - Page 14
). • LIse at least the minimum installation spacings described on page 18. This will ensure you have an adequate clearance for service and proper operation including flow of combustion and ventilation air, and that you have a sufficient distance from combustible construction. Explosion Hazard - Kenmore 9875 | Owners Manual - Page 15
valves attached to the back of the laundry center. Laundry tub drain system: Needs a minimum 20-gallon laundry tub. I ! Support: Floor must be sturdy enough to support a total weight of 500 pounds (includes laundry center and load weight). Level floor: Maximum allowable slope under entire laundry - Kenmore 9875 | Owners Manual - Page 16
No. 285320; additional drain hose, Part No. 3357090; and connector kit, Part No. 285442 Parts listed are available from your local Sears store or Sears Service Center. Call 1-800°366-PART (1-800-366-7278). 16 - Kenmore 9875 | Owners Manual - Page 17
RECESSED AREA/CLOSET INSTALLATION INSTRUCTIONS Check governing codes and ordinances. This laundry center may spacings described on page 18. This will ensure you have an adequate clearance for service and proper operation including flow of ,combustion and ventilation air, and thai: you have - Kenmore 9875 | Owners Manual - Page 18
installation spacing (shown below) is in inches and is the minimum allowable. • Additional spacing should be considered for ease of installation and servicing. • If closet door is installed, the minimum air openings in top and bottom are required. Louvered doors with equivalent air openings in top - Kenmore 9875 | Owners Manual - Page 19
centers must be securely fastened to the floor. Order Mobile Home Installation Kit 346764 from your Sears store or Sears Service Center. Kit includes the neces- sary fastening hardware and detailed installation instructions. Exhaust system hardware is also available through your Sears store or Sears - Kenmore 9875 | Owners Manual - Page 20
B. INSTALL LEVELING LEGS To install rear legs: STEP 1. If you have not already done so, lay the laundry center on its side. Because of the weight of the laundry center, two people should lay it down. STEP 2. Push legs into holes in rear corners until they snap into place. To install front legs: - Kenmore 9875 | Owners Manual - Page 21
hose from coming off or leaking, it must be installed per the following instructions: IMPORTANT: To ensure proper installation, thi:s procedure must be followed exactly. is too long Hose kit, Part No. 285442 A problem with lint clogginq your drain Drain protector, Part No. 367031 Parts listed are - Kenmore 9875 | Owners Manual - Page 22
For standpipe or laundry tub drain systems: STEP 2. Open yellow, single-wire clamp with pliers and slide over hooked end of drain hose to secure the rubber and corrugated sections together. Hooked end E. CONNECT INLET HOSES TO LAUNDRY CENTER Proper connection of your inlet hoses will allow hot and - Kenmore 9875 | Owners Manual - Page 23
fill hoses: 6 ft. hoses, Part No. 76314 or 10 ft. hoses, Part No. 350008 Parts listed are available from your local Sears store or Sears Service Center. Call 1-800-366-PART (1-800-366-7278). 23 - Kenmore 9875 | Owners Manual - Page 24
G. SECURE CABLE BRACKET STEP 1. Cut the plastic strap securing the cable wire bracket to the power supply cord. Do not cut cable. Remove the power supply cord from the bracket. Discard plastic strap. H. SECURE DRAIN HOSE Securing the drain hose properly will protect your floors from damage due to - Kenmore 9875 | Owners Manual - Page 25
all gas connections. Failure to follow these instructions can result in death, explosion, or fire sea level at the B.T.U. rating indicated on the model/serial number plate. Burner input adjustments are not of the burner B.T.U. rating shown on the model/serial number plate is required for each 1,000 - Kenmore 9875 | Owners Manual - Page 26
not agree with the type of gas available, contact your local Sears store or Sears Service Center. Any change to the burner must be made by a qualified installer. • . • For mobile home installation, see page 19 for more instructions. • The laundry center must be disconnected from the gas supply - Kenmore 9875 | Owners Manual - Page 27
CONNECT LAUNDRY CENTER TO GAS; LINE STEP 1. Remove the red cap from the gas pipe. Move the laundry, center to its final position. STEP 2. Connect gas supply to laundry center. Use a wrench to tighten. For gas connections you must use, pipe joint compound resistant to the action of L.P. gas. Apply - Kenmore 9875 | Owners Manual - Page 28
possible. Avoid 90 ° turns. Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death or fire. WARNING: To reduce the risk of fire, this dryer must be exhausted outdoors. • Use a heavy metal vent. • Do not - Kenmore 9875 | Owners Manual - Page 29
Kit No. 3391335 (white) Side Exhaust Kit No. 3391336 (almond) Follow the instructions in the kit to avoid operational and personal hazards. These kits are available at your local Sears store or Sears Service Center. DETERMINE VENT LENGTH Maximum Exhaust Lengths: • Rear Exhaust. The maximum length - Kenmore 9875 | Owners Manual - Page 30
usually comes in 2-foot lengths. Use tin snips to cut the vent 3 inches longer than your measurement in order to make a connection. Finish Installation. See "REVIEW INSTALLATION" on page 33. 3O - Kenmore 9875 | Owners Manual - Page 31
laundry center is in its final location, check to make sure the laundry center is still level (see section "1':LEVEL LAUNDRY CENTER). Finish Installation. See "REVIEW INSTALLATION" on page 33. STEP 5• Place a clamp on each end of vent elbow. Install one end of elbow on vent, the other end to the - Kenmore 9875 | Owners Manual - Page 32
, you will find it helpful to install the exhaust vent by using a loop system• A kit is available from your local Sears store or Sears Service Center• NOTE: Vent systems come in many varieties• Select the type that best fits your installation. Three of the most common types of installations are - Kenmore 9875 | Owners Manual - Page 33
REVIEW INSTALLATION Take a few minutes to complete this checklist. It will help assure you that you have a proper installation and will increase your satisfaction with your Kenmore few minutes and read the Operating Instructions (pages 34-43) to fully Troubleshooting information on pages 58-59. 33 - Kenmore 9875 | Owners Manual - Page 34
can completely remove oil. Do not dry anything that has ever had any type of oi_ on it (including cooking oils). Failure to follow these instructions can result in death, explosion, or fire. STARTING YOUR WASHER STEP 1. Add measured detergent directly into washer basket. Then place a load of sorted - Kenmore 9875 | Owners Manual - Page 35
;ET WAI"ER LEVEL CONTROL Fhis control gives you the flexibility to _ave water when washing small loads. (our washer lets you select a water ;etting based on the size of your wash oad. , For normal loads, start with the MEDIUM LOAD Setting. Adjust up or down depending on your load. Clothes should - Kenmore 9875 | Owners Manual - Page 36
SETTING YOUR CYCLE SELECTOR CONTROL (TIMER) Use this control to choose the agitation time and to start the washer. Each cycle is designed with the wash and spin speeds that are appropriate lor the fabrics and soil levels in your wash load. • For heavy soil and sturdy fabrics, use the full time ( - Kenmore 9875 | Owners Manual - Page 37
:{INSE AND SPIN Nhen using extra detergent for heavily _oiled clothes, or washing spe('ial-care terns, yOLt may find an extra rinse and _pin is needed. 3TEP 1. Set WATER LEVEL Control. _TEP 2. Set WATER TEMP Control. 3TEP 3. Set the Cycle Selector Control Timer) Knob to a RINSE setting. , For fast - Kenmore 9875 | Owners Manual - Page 38
end of draining. After Drain and Before Spin When the cycle changes from draining to spinning, you may hear a noise as the gearcase shifts. Kenmore's DUAL-ACTION" Agitator gives you flexible fabric care for even your largest loads. The best cleaning action in your washer takes place at the bottom - Kenmore 9875 | Owners Manual - Page 39
UNDER:STANDING WHAT HAPPENS IN EACH CYCLE PERMANENT PRESS Fill to selected level HEAVY DUTY Fill to selected level Wash selected time Wash selected time Partial Drain Drain no spin Pause cool down Fill for Wash no spin Drain - Spin Spin Fill to selected level IZ! Rinse Drain no spin Spin - Kenmore 9875 | Owners Manual - Page 40
including cooking oils). Items containing foam, rubber, or plastic must be dried on a clothesline or by using an air cycle. Failure to follow these instructions can result in death or fire. STEP 3. Set Cycle Selector Control (Timer) O; (see pages 41-42). STEP 4. Press PUSH TO START DRYER Button_. Be - Kenmore 9875 | Owners Manual - Page 41
:YCLE DESCRIPTION_UTOMATIC DRY CYCLES CYCLE DESCRIPTION TIMED DRY CYCLES he automatic drying cycles (NIT/DELICATE or PERMANENT RESS/NORMAL) save you time by roviding the best drying results the shortest time.This can help ou save money on utility bills and ._duce the risk of fabric damage. Ise the - Kenmore 9875 | Owners Manual - Page 42
USING AIR DRY Using this cycle gives you all the benefits of hang drying with a shorter drying time. Use the AIR DRY Cycle to get up to 20 minutes of drying time in room temperature air. Use this setting for items that will not tolerate heat such as plastics and foam rubber. Also use for airing and - Kenmore 9875 | Owners Manual - Page 43
the formation of small lint-like balls on the surface of garments. Pilling is the natural result of washing and wearing of garments. Kenmore dryers help prevent overdrying so you get outstanding fabric care. In the automatic drying and timed drying cycles, clothes are dried at the temperature - Kenmore 9875 | Owners Manual - Page 44
PREPARING CLOTHES FOR WASHING AND DRYING Follow these recommendations to help save on utility bills and prolong the life of your garments. WASHING AND DRYING TIPS • Close zippers, snaps, and hooks to avoid snagging other items. Remove heat-sensitive trim that can be damaged by drying. Tie string.,; - Kenmore 9875 | Owners Manual - Page 45
LOADING Proper loading of your laundry center zontributes to proper cleaning and iabric ca,'e and reduces machine noise. LOADING TIPS - WASHER , Drop items into washer loosely. Fill to the top of the basket (top row of holes). Do not wrap items around the agitator. Items should move easily through - Kenmore 9875 | Owners Manual - Page 46
small lightweight items from blocking airflow. USING DRYER FABRIC SOFTENERS Dryer fabric softeners are recommended for reducing static cling. Always follow package instructions carefully. • Put one fabric softener sheet on top of the load before starting the dryer. Do not add a fabric softener sheet - Kenmore 9875 | Owners Manual - Page 47
fabric instead of through it. • Meat tenderizer or enzyme presoaks help break down some protein stains so they are easier to remove. STAIN REMOVAL GUIDE Alcoholic beverage These stain.:; turn brown with age, so treat immediately. Sponge or soak fresh stains with cold water. Wash. If stain remains - Kenmore 9875 | Owners Manual - Page 48
Deodorants or antiperspirants Light stain: Treat with liquid detergent or your regular laundry detergent. Wash in hottest water safe for fabric. Heavy stain: Place face down on towel and treat with a paste of ammonia and color-safe bleach. Let stand for 30 minutes. Wash in hottest water safe for - Kenmore 9875 | Owners Manual - Page 49
_lildew h/ash in hottest water safe for fabric. f stain remains, soak in warm water and color-safe bleach for 15 to 30 minutes. :{ewash. (Old mildew stains are almost mpossible to remove. Mildew fungus :testroys or weakens fabrics.) An alterlative to bleach is to treat with salt and emon juice and - Kenmore 9875 | Owners Manual - Page 50
flow to care for your laundry center properly and safely. Proper care of your laundry center (:an extend its life and help you avoid costly service calls. (;LEANING YOUR WASHER EXTERIOR Wipe up detergent, bleach, and other spills with a soft, damp cloth or sponge as they occur. Occasionally wipe the - Kenmore 9875 | Owners Manual - Page 51
CLEANING THE LINT SCREEN Remove Lint Before Every Load The lint screen is located on the back wall of your dryer. Clean it before every load. A screen blocked by lint can increase drying time. To clean:: STEP 1. Pull out the lint screen and its cover. STEP 2. Separate the cover and the screen by - Kenmore 9875 | Owners Manual - Page 52
often, dependir_g on dryer usage. Cleaning should be done by a qualified service person. To remove accumulated lint from exhaust vent: STEP 1. Disconnect exhaust vent Reconnect vent as described in the "INSTALLATION INSTRUCTIONS" of this Owner's Manual. To remove accumulated lint from inside the - Kenmore 9875 | Owners Manual - Page 53
WINTEFI STORAGE Install and store your laundry center where it will not freeze. Because some water may stay in the hoses, freezing can damage your laundry center. If storing or moving your laundry center during freezing weather winterize it. To winterize laundry center: 1. Shut off both water - Kenmore 9875 | Owners Manual - Page 54
are easily solved if you understand the cause. Check these tables for common laundry and washer problems. If you need further assistance, see page 62. Problem Possible Cause Solution Washer Leaks Household plumbing is leaking. Repair plumbing. Inlet hoses not tight. Inlet hose washers not - Kenmore 9875 | Owners Manual - Page 55
Problem Won't Drain/ Won't Spin/ Wet Loads (cont'd) Possible Cause Low voltage or . Washer Makes Load is unbalanced. Noise Laundry center is not level. Floor not strong enough to support laundry center. Gears engaging after drain and before spin. Upper part of agitator clicks during wash. - Kenmore 9875 | Owners Manual - Page 56
knob not pulled out. Was;tier at pause in PERMANENT PRESS Cycle (approximately two minutes). Machine is overloaded. Replace fuse or reset circuit breaker. If problem continues, call electrician. Do not use an extension cord. Turn timer to the right slightly and pull to start. Set and pull out knob - Kenmore 9875 | Owners Manual - Page 57
Problem Tearing Stains on Load Load is Wrinkle4 Load is Tangled/ Twisted Possible Cause Solution Overloading. Improper use of washer, Loads should move freely during wash. - Kenmore 9875 | Owners Manual - Page 58
Problem Not Drying Satisfactorily Dryer Will Not Run Possiible Cause Solution Lint screen is clogged with lint. Restri,3ted air movement. Exhaust vent or outside exhaust - Kenmore 9875 | Owners Manual - Page 59
Problem Lint in Load Possible Cause Lint screen is clogged. Improper sorting. Load is to fabric type (see "OPERATION"). Check quality of garment before purchasing. Follow fabric care label instructions carefully. Dry smaller loads that can tumble freely. Match dryer settings to fabric type (see " - Kenmore 9875 | Owners Manual - Page 60
What We Sell" is our assurance that you can depend on Sears for service. Your Kenmore Laundry Center has added value when you consider that Sears has service units nationwide, staffed with professional technicians trained on all appliances Sears sells. They have the knowledge and skills, tools
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
 |
 |
Owner's Manual and
Installation
Instructions
24-Inch Wide
®
LAUNDRY
CENTER
Washer
•
Gas Dryer
,-----.__...__
t-----
I
i
.,,J
IMPORTANT:
Read and follow
all safety
and operating
instructions
before first use of this product.
Sears,
Roebuck
and Co., Hoffman
Estates,
IL 60179
U.S.A.
PART NO. 3405594
PRINTED
IN U.S.A.