Kenwood NX-410 User Manual 1

Kenwood NX-410 Manual

Get Kenwood NX-410 PDF manuals and user guides View all Kenwood NX-410 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood NX-410 manual content summary:

  • Kenwood NX-410 | User Manual 1 - Page 1
    NX-410/ NX-411 800MHz DIGITAL TRANSCEIVER 900MHz DIGITAL TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR NUMÉRIQUE 800MHz ÉMETTEUR-RÉCEPTEUR NUMÉRIQUE 900MHz MODE D'EMPLOI TRANSCEPTOR DIGITAL 800MHz TRANSCEPTOR DIGITAL 900MHz MANUAL DE INSTRUCCIONES © B62-2364-00 (K) 09 08 07 06 05 04 03 02 01 00
  • Kenwood NX-410 | User Manual 1 - Page 2
    ENGLISH 800MHz DIGITAL TRANSCEIVER 900MHz DIGITAL TRANSCEIVER NX-410/ NX-411 INSTRUCTION MANUAL Terminal Descriptions Universal connector It is possible to use a resin-based cover for the Universal connector. NO. Name Description Impedance I/O 1 SSW Ext/Int Speaker Switch
  • Kenwood NX-410 | User Manual 1 - Page 3
    have chosen Kenwood for your land mobile radio applications. This instruction manual covers only the basic operations of your NEXEDGE portable radio. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. SAFETY: It is important that the operator
  • Kenwood NX-410 | User Manual 1 - Page 4
    radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO
  • Kenwood NX-410 | User Manual 1 - Page 5
    The RBRC Recycle seal found on Kenwood lithium-ion (Li-ion) battery packs indicates Kenwood's voluntary participation in an industry program to collect and recycle Li-ion batteries after their operating life has expired. The RBRC program is an alternative to disposing Li-ion batteries with your
  • Kenwood NX-410 | User Manual 1 - Page 6
    PRECAUTIONS • Do not charge the transceiver and battery pack when they are wet. • Ensure that there are no metallic items located between the transceiver and the battery pack. • Do not use options not specified by Kenwood. • If the die-cast chassis or other transceiver part is damaged, do not touch
  • Kenwood NX-410 | User Manual 1 - Page 7
    . • In aircrafts. (Any use of the transceiver must follow the instructions and regulations provided by the airline crew.) • Where restrictions or warnings are powders, etc.). • While taking on fuel or while parked at gasoline service stations. • The orange seal on the reverse side of the transceiver
  • Kenwood NX-410 | User Manual 1 - Page 8
    transceiver on or near airbag equipment while the vehicle is running. When the airbag inflates, the transceiver may be ejected and strike the driver or passengers. • Do not transmit while touching the antenna terminal or if any metallic parts are exposed from the antenna covering. Transmitting at
  • Kenwood NX-410 | User Manual 1 - Page 9
    INFORMATION CONCERNING THE BATTERY PACK The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters. •
  • Kenwood NX-410 | User Manual 1 - Page 10
    • Do not charge the battery near fires or under direct sunlight! If the battery's protection circuit is damaged, the battery may charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame. • Use only the
  • Kenwood NX-410 | User Manual 1 - Page 11
    eyes out with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has
  • Kenwood NX-410 | User Manual 1 - Page 12
    CONTENTS UNPACKING AND CHECKING EQUIPMENT 1 SUPPLIED ACCESSORIES 1 PREPARATION 2 INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK 2 INSTALLING THE (OPTIONAL) ANTENNA 2 INSTALLING THE BELT CLIP 3 INSTALLING THE CAP OVER THE UNIVERSAL CONNECTOR 3 INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE OR
  • Kenwood NX-410 | User Manual 1 - Page 13
    LOW BATTERY WARNING 27 SIGNAL STRENGTH INDICATOR 27 COMPANDER 28 BUSY CHANNEL LOCKOUT (BCL 28 CONTROL CHANNEL HUNT 28 PTT ID 28 VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT 29 VOICE RECORDER 29 VOICE
  • Kenwood NX-410 | User Manual 1 - Page 14
    UNPACKING AND CHECKING EQUIPMENT Note: These unpacking instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Carefully unpack the transceiver 1 • Screws for belt clip (3 x 8 mm 2 Universal connector cap 1 • Dressing screw 1 Instruction manual 1 1
  • Kenwood NX-410 | User Manual 1 - Page 15
    REMOVING THE (OPTIONAL) BATTERY PACK 1 Match the guides of the battery pack with the grooves on the 3 Note: ◆ For battery pack charging procedures and useage, refer to the battery charger Instruction Manual. ◆ Before charging a battery pack that is attached to the transceiver, ensure that the
  • Kenwood NX-410 | User Manual 1 - Page 16
    secure it in place using the attached screw. MIC Universal connector cap INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE OR HEADSET 1 Insert the guide of the speaker/ microphone or headset connector into place over the universal connector. 2 Secure the connector in place using the attached screw
  • Kenwood NX-410 | User Manual 1 - Page 17
    GETTING ACQUAINTED a Selector knob Rotate to select a zone or channel/group ID (default). b Power switch/ Volume control Rotate to turn the transceiver ON/OFF and to adjust the volume. c Transmit/ Receive/ Battery low indicator If enabled by your dealer, lights red while transmitting, green while
  • Kenwood NX-410 | User Manual 1 - Page 18
    e Side 1 key Press to activate its programmable function {page 7}. The default is Squelch Off Momentary. f PTT (Push-To-Talk) switch Press and hold this switch, then speak into the microphone to call a station. g Side 2 key Press to activate its programmable function {page 7}. The default is
  • Kenwood NX-410 | User Manual 1 - Page 19
    DISPLAY Indicator 6 Description Monitor or Squelch Off is activated. Blinks when an incoming call matches your Optional Signaling. The current zone (left icon) or CH/GID (right icon) is added to scan. Scan is in progress. Blinks while scan is paused. A message is stored in memory. Blinks when a
  • Kenwood NX-410 | User Manual 1 - Page 20
    PROGRAMMABLE FUNCTIONS Following is a list of available programmable functions. Please contact your dealer for further details on those functions which have been programmed on your transceiver. • Auto Reply Message 2 • Auto Telephone 3 • Autodial • Autodial Programming • AUX • Backlight •
  • Kenwood NX-410 | User Manual 1 - Page 21
    • Voice Memo 2 • VOX 11 • Zone Delete/Add • Zone Down • Zone Up 1 Available only for Analog Conventional operation. 2 Available only if the VGS-1 optional board has been installed. 3 Available only for Analog Trunking operation. 4 Available only for Analog Conventional, Analog Trunking, and NXDN
  • Kenwood NX-410 | User Manual 1 - Page 22
    BASIC OPERATIONS SWITCHING POWER ON/OFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. Turn the Power switch/ Volume control counterclockwise fully to switch the transceiver OFF. ■ Transceiver Password If the transceiver is password protected, "PASSWORD" will appear on
  • Kenwood NX-410 | User Manual 1 - Page 23
    SELECTING A ZONE AND CHANNEL/GROUP ID Select the desired zone using / (default). Each zone contains a group of channels. Select the desired channel/group ID using the Selector knob (default). Each channel/group ID is programmed with settings for transmitting and receiving. • You can toggle the
  • Kenwood NX-410 | User Manual 1 - Page 24
    ■ Making Individual Calls (Digital) If a key has been programmed with Individual or Individual + Status, you can make calls to specific persons. 1 Press the key programmed as Individual or Individual + Status. 2 Press / to select a unit ID from the list. • You can enter the unit ID directly, using
  • Kenwood NX-410 | User Manual 1 - Page 25
    MENU MODE Many functions on this transceiver are selected or configured through the Menu instead of physical controls. Once you become familiar with the Menu system, you will appreciate the versatility it offers. MENU ACCESS 1 Press the key programmed as Menu. • The category list is shown. • When
  • Kenwood NX-410 | User Manual 1 - Page 26
    Display CLOCK ADJUST DIRECT CH1 SEL DISP FORMAT EXT MIC TYPE FIXED VOLUME FORCED SEARCH GPS POS DISP GROUP GROUP+STATUS GROUP+SDM HOME CH SEL INDIVIDUAL INDIV+STATUS INDIV+SDM LONE WORKER LOW TX POWER MAINTENANCE MONITOR OST OST LIST PLAYBACK PRI CH SEL RX AUDIO EQ RX AGC RX LOW CUT SCAN SCAN DEL/
  • Kenwood NX-410 | User Manual 1 - Page 27
    Display STACK STATUS SHORT MESSAGE TALK AROUND TX AUDIO EQ TX AGC TX NOISE SUPPR PASSWORD VIBRATOR VOICE MEMO VOX LEVEL VOX ZONE DEL/ADD Description Stack mode Status mode Short Mesage mode Talk Around ON/OFF TX Audio Equalizer mode TX Audio Gain Control mode TX Noise Suppressor mode Transceiver
  • Kenwood NX-410 | User Manual 1 - Page 28
    SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. To begin scanning, press the key programmed as Scan. • The icon appears on the display. • When a signal is detected on a channel,
  • Kenwood NX-410 | User Manual 1 - Page 29
    SCAN REVERT The Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of the following types of Scan Revert channels: • Selected: The last channel selected before scan. • Selected + Talkback: Same as "Selected", plus you can
  • Kenwood NX-410 | User Manual 1 - Page 30
    channel. 2 Press the key programmed as Selcall or Selcall + Status to enter Selcall mode. 3 Press / to select the station you want to call. • If Manual Dialing is enabled, you can directly enter the station ID using the DTMF keypad. 4 Press the PTT switch and begin your conversation. ■ Receiving An
  • Kenwood NX-410 | User Manual 1 - Page 31
    to step 3). 3 Press / to select the station you want to call. • If Manual Dialing is enabled, you can enter a station ID by using the DTMF keypad, or Status mode. 5 Press / to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a status ID by using the DTMF keypad,
  • Kenwood NX-410 | User Manual 1 - Page 32
    . Ask your dealer for details. GPS REPORT To send your location data, you must first connect a GPS unit to the transceiver. GPS data can be manually transmitted by pressing the key programmed as Send the GPS data, or by accessing the Menu {page 12}. If set up by your dealer, GPS
  • Kenwood NX-410 | User Manual 1 - Page 33
    ADVANCED OPERATIONS DTMF (DUAL TONE MULTI FREQUENCY) CALLS ■ Making a DTMF Call Manual Dialing 1 Press and hold the PTT switch. 2 Enter the desired digits using the DTMF keypad. • If you release the PTT switch, transmit mode will end
  • Kenwood NX-410 | User Manual 1 - Page 34
    transceiver becomes disabled. The stun code is cancelled when the transceiver receives a call with a revive code. TRUNKING CALLS ■ Making a Telephone Call Manual Dialing (Analog) 1 Select your desired zone and telephone group ID. 2 Press the PTT switch to start the call. 3 Enter your desired number
  • Kenwood NX-410 | User Manual 1 - Page 35
    EMERGENCY CALLS If your transceiver has been programmed with the Emergency function, you can make emergency calls. 1 Press and hold the key programmed as Emergency. • Ask your dealer for the length of time necessary to hold this key before the transceiver enters Emergency mode. • When the
  • Kenwood NX-410 | User Manual 1 - Page 36
    SIGNALING ■ Quiet Talk (QT)/ Digital Quiet Talk (DQT) Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls from other parties who are using the same channel. Operator Selectable
  • Kenwood NX-410 | User Manual 1 - Page 37
    ■ Optional Signaling Your dealer may also program several types of optional signaling for your transceiver channels. DTMF Signaling: DTMF Signaling opens the squelch only when the transceiver receives a call containing a matching DTMF code. FleetSync Signaling: Refer to "SELCALL (SELECTIVE CALLING)"
  • Kenwood NX-410 | User Manual 1 - Page 38
    ■ VOX Operation 1 Connect the headset to the transceiver. 2 Press and hold the key programmed as VOX for 2 seconds. 3 To transmit, simply speak into the microphone. • The transceiver recognizes sound levels depending on the VOX Gain level. If it is too sensitive, it will transmit when there is noise
  • Kenwood NX-410 | User Manual 1 - Page 39
    BACKGROUND OPERATIONS Your dealer can activate a variety of transceiver functions to perform without any additional operation on your part. CLOCK If activated by your dealer, you can view the clock by pressing the key programmed as Clock. Note: Removing or leaving the battery pack uncharged for
  • Kenwood NX-410 | User Manual 1 - Page 40
    BATTERY SAVER The Battery Saver can be activated only on Conventional channels. This function decreases the amount of power used when a signal is not being received and no operations are being performed. KEY LOCK Press the key programmed as Key Lock to lock and unlock the transceiver keys. • The
  • Kenwood NX-410 | User Manual 1 - Page 41
    COMPANDER If programmed by your dealer for a channel, the compander will remove excessive noise from transmitted signals, to provide higher clarity of signals. Note: The COMPANDER is used only in analog operation. BUSY CHANNEL LOCKOUT (BCL) On Conventional channels, if BCL is set up by your dealer,
  • Kenwood NX-410 | User Manual 1 - Page 42
    VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT VOICE RECORDER The voice recorder allows you to record conversations and create voice memos. ■ Auto Recording If activated, the auto recorder will continuously
  • Kenwood NX-410 | User Manual 1 - Page 43
    end the recording at any time by pressing . • To delete the selected recording, press . To clear all the recorded data, press and hold . VOICE GUIDE When changing the zone and/or channel, an audio voice will announce the new zone and channel. Additionally, when changing a function setting, the new
  • Kenwood NX-410 | User Manual 1 - Page 44
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
© B62-2364-00 (K)
09 08 07 06 05 04 03 02 01 00
NX-410/ NX-411
800MHz DIGITAL TRANSCEIVER
900MHz DIGITAL TRANSCEIVER
INSTRUCTION MANUAL
ÉMETTEUR-RÉCEPTEUR NUMÉRIQUE 800MHz
ÉMETTEUR-RÉCEPTEUR NUMÉRIQUE 900MHz
MODE D’EMPLOI
TRANSCEPTOR DIGITAL 800MHz
TRANSCEPTOR DIGITAL 900MHz
MANUAL DE INSTRUCCIONES