Konica Minolta KIP 770 KIP 770 User Guide

Konica Minolta KIP 770 Manual

Get Konica Minolta KIP 770 PDF manuals and user guides View all Konica Minolta KIP 770 manuals
Add to My Manuals
Save this manual to your list of manuals

Konica Minolta KIP 770 manual content summary:

  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 1
    KIP 770 User Manual Version A.0
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 2
    you for purchasing the Multi-Function Printer KIP 770. This Hardware Operation Guide contains functional and operational explanations for the KIP 770. Please read this Hardware Operation Guide carefully before using the printer. Please keep this Hardware Operation Guide for future reference. 1. When
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 3
    the operator or operation of the printer. The following symbols are found throughout the USER'S Manual and have the following meaning: WARNING instruction. CAUTION This CAUTION mark means that there is a possibility of injury or physical damage if you ignore or do not follow the said instruction.
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 4
    you wish to move the printer, please contact your service personnel. 1. Do not remove the screw and do not open the cover if not instructed to do so in this User's Manual. If you ignore this outlet immediately. Do not throw the toner into a fire or other sources of heat, as it can explode. (3)
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 5
    result in a fire or electric shock. 2. If you do not use the printer for a long duration (holidays, company shutdown) turn off and unplug the printer from the outlet for safety. Do not pull the cord when you unplug the printer as you may damage the Power Cord. There are hot items inside of
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 6
    POWER CORD INSTRUCTION The installation of (or exchange to) a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 7
    Chapter 1 Before Use 1. 1 Installation Requirements 1. 2 Originals Prohibited from Duplication 1. 3 Features 1. 4 Specifications 1. 4. 1 General 1. 4. 2 Printer part 1. 4. 3 Scanner part 1. 5 Appearance 1. 5. 1 Front view 1. 5. 2 Rear view 1. 6 Specifications for the Scan Original 1. 7
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 8
    to the direct sunlight. Please draw curtains to block any sunlight. When you open the printer (Upper Half), do not expose the Photoconductive Drum to strong (intense) light as this (Front) 20cm/8" or larger with no option KIP 770 20cm/8" or larger 10cm/4" or larger 1-2 Chapter 1 Before Use
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 9
    1. 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original. You may be punished by the law if only you possess the copy of some kind of original. We recommend you to consider enough before you copy such original. [Originals prohibited from copying by
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 10
    space. (3) Various media source; roll media feeding (1 roll), cut sheet manual feeding, Paper Tray multiple cut sheet feeder (option). (4) A dedicated printer stand offers easy print handling with the print basket. The KIP 770 is also suitable for your office layout as a desktop MFP. (5) The
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 11
    ) Power consumption (Low power mode) Acoustic noise Ozone Dimensions Weight Environmental condition for usage Interface Rating input power Specification KIP 770 Console 1500w (US model) 1600w (Europe/Asia model) (Including Scanner & Controller Unit) Conformity with International Energy Star Program
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 12
    1. 4. 2 Printer part Subject Printing method Photoreceptor Print speed Print head Resolution of print head Print width Print length plain paper (after submission of the concerning plot data) Heat and Pressure Rollers Dry type non-magnetic mono-component toner 1-6 Chapter 1 Before Use
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 13
    Specification 1 Roll Deck (3" / 2" core roll* ) Manual Feeder (single cut sheet) Paper Tray (multiple cut sheet * : Universal Bond Paper Storage of consumables (Cut sheet) Plain Paper / Bond (Toner cartridge) Store the cartridge within the temperature range from 0 to 40 degrees Centigrade and
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 14
    1. 4. 3 Scanner part Subject Scanning method Light source Setting of original Starting point of scan Scan width Scan length Margin area Optical resolution Digital resolution Original transportation Transportable original thickness Specification Contact Image Sensor (CIS) (5 pieces of A4 sized CIS)
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 15
    Button 12 Start Button 13 Print Exit Cover 14 Initial Cut Button 2 14 8 2 Function You can turn on/off the KIP 770. Feed the original under the Scanner Unit along the Original Guides. This is a Touch Screen, and many kinds of user operation are available. PLEASE DO NOT push the LCD area too
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 16
    Cover 2 Original Guide 3 LAN Port 4 USB Port 5 Breaker 6 Inlet Socket 4 3 Function Open here to access toner supply system. These trays catch the original ejected from the Scanner Unit. Connect the LAN Cable to connect the KIP 770 to the network. (Do not connect a telephone line) Service Use, 5VDC
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 17
    1. 6 Specifications for the Scan Original A scan original must satisfy the following specifications. Thickness Width Length 0.05mm to 1.6mm *1 210mm to 914.4mm 210mm to 6000mm *2 *1. Image quality for an original with 0.25mm or thicker is guaranteed only in a standard size even the scanner
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 18
    Not square Wet Metal or fabric material Rough surface (Carbon paper for example) Clipped or stapled KIP KIP Metal Wet Fabric KIP KIP Rough surface Clipped Stapled KIP KIP 1-12 Chapter 1 Before Use
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 19
    The following kinds of originals can be read with using a carrier sheet. Image quality or the reliability of paper feeding for them is not guaranteed. Patched Punched 1-13 Chapter 1 Before Use
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 20
    1. 7 Specifications for the Printing Paper 1. 7. 1 Papers not available to use Do not use the following kinds of printing paper. Doing so may damage the print engine. Excessively curled (a diameter of 50 mm or less) Folded Creased Torn Punched 1-14 Chapter 1 Before Use
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 21
    Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film CAUTION Do not use the paper with staple, or do not use such conductive paper as aluminum foil and carbon paper. The above may result in a danger of fire. NOTE (1) Print image may become light if printed on a rough
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 22
    tracing paper. "Void of image" occurs when you print with plain paper and tracing paper. "Void of image", "crease of paper" and other problems occurs when you print with plain paper and tracing paper. Necessary treatment 1. Install an humidifier in the room, and humidify the room air. 2. Remove
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 23
    Chapter 2 Basic Operation 2. 1 Turning on KIP 770 2. 2 Turning off KIP 770 2. 3 Replacing Roll Media 2. 4 Initial Cut 2. 5 Toner Supply 2. 6 Cut Sheet Media 2. 7 Copying 2. 8 Stop of Scan or Copy 2. 9 Canceling Sleep Mode 2. 10 Dehumidifying Roll Media 2-1 3age 2- 2 2- 4 2- 5 2- 9 2-10 2-14 2-15
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 24
    and 15A In Europe : 220-240V plus 6% or minus 10%, 50/60Hz and 10A 2. Press " | " side the Power Switch on the right side of the printer to turn on the KIP 770. Power Switch Press " | " side. 2-2 Chapter 2 Basic Operation
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 25
    indicator on the upper left corner of UI screen lights in orange. 4. When the lighting status of Ready Indicator changes from "red" to "green", the KIP 7170 is ready for operation. Ready Indicator 2-3 Chapter 2 Basic Operation
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 26
    Power Switch on the right side of KIP 770. Press its " " side to turn off the KIP 770. Power Switch Press " " side. CAUTION The KIP 770 print engine and UI appear to be shut down when you turn off KIP 770. However, the controller PC embedded inside the KIP 770 is still operating and will shutdown
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 27
    2. 3 Replacing Roll Media When the printer is running out of a roll media, the UI Screen will display "Roll Replacement" sign. Follow the later procedure (or as noted in the UI's User Guide) to load a roll media. Please refer to your KIP IPS Touch Screen Operator's Guide for the UI screen. NOTE A
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 28
    4. Insert each Flange (2) into both ends of the roll media core to be installed. 2 NOTE (1) Fully insert Flange into the roll media core so that the inside rim of Flange evenly touches the side face of the roll media. Inside Rim Inside Rim Gap Correct: Fully inserted Wrong: not touching roll
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 29
    (1) Be careful of the winding direction of the roll media. This direction (2) The outside rim of Flange (2) should fit into the groove on the Slide Guide. Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding. 2 groove 2 groove 2-7 Chapter 2 Basic Operation
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 30
    edge will automatically go into the roll media's wait position. This is called "Auto Media Loading". 6 Reference Auto Media Loading becomes available while the printer is ready. 8. Trim the leading edge of the roll media with "Initial Cut" function if necessary. For Initial Cut, see the next page on
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 31
    Initial Cut is a function to trim the roll media with its leading edge cut off. (2) Initial Cut becomes available while the printer is ready. 1. Open the Manual Feeder Table (1). 1 2. Press the green button (2) on the right. 2 3. The leading edge of the roll media is automatically transported and
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 32
    Empty sign. Follow the later procedure (or as noted in the UI's User Guide) to Supply the Toner with a new one (genuine). When the UI screen shows "Adding Toner", follow the instruction to install a genuine Toner Cartridge. 1. Open the Toner Hatch (1) on the rear top. You do not have to remove the
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 33
    3. Put the dent area (3) under the holder (4) to firmly seat the bottom plate of the Toner Bottle (2) to the toner supply position. from front from right 3 4 2 4 from front 2-11 Chapter 2 Basic Operation
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 34
    Bottle. Pressing too much makes the lever (5) much heavier. 5. Slide the green lever (5) to the original position. Remove the Toner Bottle. from right 2 5 NOTE It is impossible to remove the Toner Bottle unless the lever (5) completely moves to the original position. Do not attempt to remove the
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 35
    6. Close the Toner Hatch (1). 1 7. Press [OK] button on the UI screen. OK 2-13 Chapter 2 Basic Operation
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 36
    on the table between its concerning size markings then insert it into the Bypass Feeder. When the leading edge touches the feeding roller, the printer automatically carries and sets the paper at the proper position. size marking NOTE (1) As a curly cut sheet will cause a mis-feed, straighten the
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 37
    face up. Then insert it under the Scanner Unit along with Original Guides. When the leading edge touches the original feeding roller, the machine automatically carries and sets the original at the proper position. 3. The KIP 770 will start the copy process. Reference Pressing START button may be
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 38
    2. 8 Stop of Scan or Copy 1. If necessary, press the Scan Abort Button on the Scanner Unit to immediately stop the original while making a copy or scan. Scan Abort Button Pressing the button stops the current reading a document immediately. The current printing is stopped as well and is ejected.
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 39
    the scanner unit. NOTE (1) It may take time for the machine to get ready. (2) Tapping on the UI screen can cancel the screensaver but the KIP 770 needs to recover temperature on Fuser Unit. It may need another waiting time to start warming up for printing. (3) Recommended Default Delay Times: 60min
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 40
    has too much humidity (65% or higher) to prevent the above kinds of print defect. You may be able to fix the above kinds of problem. The KIP 770 has a built-in Dehumidify Heater (option). To turn on the Dehumidify Heater, press the H side of the Dehumidify Heater Switch on the rear. (Press
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 41
    1 Mis-feed Error 3. 1. 1 J-0103 Roll Deck section 3. 1. 2 J-0203 Manual Feeder section 3. 1. 3 J-0104 / 0204 Media Feed section 1 3. 1. 4 J-0105 3. 2 Other Operator Call Error 3. 2. 1 Roll Replacement 3. 2. 2 Toner Empty 3. 2. 3 Scanner Open 3. 3 Service Call Error 3-1 3age 3- 2 3- 3 3- 5 3- 6 3- 8
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 42
    Please refer to the following figure to check the jam location. (Mis-feed Codes are described on the later pages.) Fuser Section J-0106 / 0206 Manual Feeder Section J-0203 Feed Section 2 J-0105 / 0205 Feed Section 1 J-0104 / 0204 Roll Deck Section J-0103 NOTE (1) Be careful not to get paper cuts
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 43
    3. 1. 1 J-0103 Roll Deck section Remove a mis-feed media in the Roll Deck if the UI screen will show J-0103. J-0103 1. Open the Roll Deck Cover. Rewind the roll onto the media core. 2. Rotate the roll media in the arrow direction and insert the leading edge of the roll media to the media path until
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 44
    the core (by glue or a tape), a small portion of the media may remain in the media path of the Roll Deck at a roll empty. The printer does not show any mis-feed error code against the portion. So please check for the portion in the media path through the square window
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 45
    if the UI screen will show J-0203. J-0203 1. Pull out the mis-feed cut sheet from the Manual Feeder. NOTE The mis-feed cut sheet should be replaced with a new one if its leading edge has a torn or fold. Or it should be
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 46
    3. 1. 3 J-0104 / 0204 Media Feeder section 1 Remove a mis-feed media in the Media Feeder section 1 if the UI screen will show J-0104 or 0204. J-0104 or J-0204 1. Press down the blue levers (1) on both sides to unlock and open the Upper Unit. 1 1 2. Remove the mis-feed media. 3-6 Chapter 3
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 47
    3. Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit. Push the entire unit down to the arrow direction. Hold here Hold here 3-7 Chapter 3 Error Correction
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 48
    3. 1. 4 J-0105 / 0205 Media Feeder section 2 Remove a mis-feed media in the Media Feeder section 2 if the UI screen will show J-0105 or 0205. J-0105 or J-0205 1. Press down the blue levers (1) on both sides to unlock and open the Upper Unit. 1 1 2. Remove the mis-feed media. 3-8 Chapter 3
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 49
    3. Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit. Push the entire unit down to the arrow direction. Hold here Hold here 3-9 Chapter 3 Error Correction
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 50
    edge area is coming to the Fuser and you cannot pull it out, or if the trailing edge remains deep to be caught in the printer, do not pull it by force. Leave it there and go to the next step. WARNING There are extremely hot parts inside the Fuser Unit
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 51
    3. Press down the blue levers (3) on both sides to unlock and open the Upper Unit. 3 3 4. Remove the mis-feed media. 5. Close the Exit Door. 3-11 Chapter 3 Error Correction
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 52
    6. Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit. Push the entire unit down to the arrow direction. Hold here Hold here 3-12 Chapter 3 Error Correction
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 53
    / 1300 / 1400 Door Open while printing If the Exit Cover or the Upper Unit is open while the printer is processing a print job, the UI screen will show J-1200 (Exit Cover) /J-1300 (Manual Feeder Table) / J-1400 (Upper Unit). 1. Hold the blue handle (1) and open the Exit Cover (2). 1 2 2 2. If it is
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 54
    4. Remove the mis-feed media. If the mis-feed media does not exist, go to the next step. 5. Close the Exit Door. 6. Put your hands on the rear rim of the scanner unit just as you hold the Upper Unit. Push the entire unit down to the arrow direction. Hold here Hold here 3-14 Chapter 3 Error
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 55
    7. Open the Roll Deck Cover. Rewind the roll onto the media core. 8. Rotate the roll media in the arrow direction and insert the leading edge of the roll media to the media path until it touches the feeding rollers (4). After that, the leading edge will automatically go into the roll media's wait
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 56
    3. 1. 7 Original Jam If an original is mis-fed while scanning, the UI screen shows "Original Jam". Follow the instruction below to remove the mis-fed original. 1. Lift up both sides (1) of the Scanner Unit 1 2. Remove a mis-feed original. 3. Gently press the Scanner Unit down
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 57
    Deck. For the roll replacement procedure, see [2.3 Replacing Roll Media]. 3. 2. 2 Toner Empty When the printer is running out of toner, the UI Screen will display "Toner Empty" sign. For the toner supply procedure, see [2.5 Toner Supply]. 3. 2. 3 Scanner Unit Open The UI screen shows "Scanner Unit
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 58
    above errors appear: 1. Turn off KIP 770, and turn it on after an interval of 30 seconds or more. 2. If the same error code appears, turn off KIP 770, and then unplug the printer from the wall outlet after an interval of two minutes for shutdown. Call your service personnel. 3-18 Chapter 3 Error
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 59
    Chapter 4 Maintenance 4. 1 Scanner Unit 4. 1. 1 Scan Glass, Feed Roller, Guide Plate 4. 1. 2 Sensor 4. 2 Touch Screen 4-1 3age 4- 2 4- 2 4- 5 4- 7 Chapter 4 Maintenance
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 60
    4. 1 Scanner Unit 4. 1. 1 Scan Glass, Feed Roller, Guide Plate It is recommended to clean each Scan Glass, Feeding Rollers and Guide Plates as the scan/copy image may become defective if these parts are dirty. 1. Turn off KIP 770. 2. Lift up both sides (1) of the Scanner Unit. 1 1 4-2 Chapter 4
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 61
    3. Gently wipe the Scan Glass (2) and Feed Rollers (white) (3) with a soft cloth. Equal mixture of water and neutral detergent can be used. 2 3 NOTE Do not use organic solvent, glass cleaner and anti-static spray for the cleaning. 4. Wipe the Feed Rollers (rubber) (4) with a dry cloth. 5. Wipe
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 62
    6. Wipe the Upper Guide Plate (5) and the Lower Guide Plate (6) with a dry cloth. 5 5 6 7. Gently press Scanner Unit down and firmly close it. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing only one side down. 4-4 Chapter 4 Maintenance
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 63
    incorrectly. Perform cleaning or as needed. NOTE For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1. Turn off KIP 770. 2. Lift up both sides (1) of the Scanner Unit. 1 1 4-5 Chapter 4 Maintenance
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 64
    3. Gently wipe Sensors (2) with a dry cotton bud. 2 2 2 2 2 2 2 NOTE Do not use water, organic solvent, glass cleaner or antistatic spray for cleaning. 4. Gently press Scanner Unit down and firmly close it. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 65
    4. 2 Touch Screen 1. Wipe the Touch Screen with a dry cloth. NOTE Do not use water, alcohol, organic solvent and glass cleaner for the cleaning. 4-7 Chapter 4 Maintenance
  • Konica Minolta KIP 770 | KIP 770 User Guide - Page 66
    © 2014 KATSURAGAWA ELECTRIC CO., LTD. No part of this publication may be copied, reproduced or distributed in any form without express written permission from Katsuragawa Electric Co., Ltd. 58
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
KIP 770 User Manual
Version A.0