Konica Minolta KIP 800 Color Series KIP 800 Series Hardware Operation Guide
Konica Minolta KIP 800 Color Series Manual
View all Konica Minolta KIP 800 Color Series manuals
Add to My Manuals
Save this manual to your list of manuals |
Konica Minolta KIP 800 Color Series manual content summary:
- Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 1
KIP 800 | Color Series Hardware Operation Guide Version A.0 - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 2
KIP 800 Series. This Hardware Operation Guide contains functional and operational explanations for the KIP 800 Series. Please read this Hardware Operation Guide carefully before using the Printer. Please keep this Hardware Operation Guide in accordance with the instruction manual,, may cause harmful - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 3
KIP 800 Series is an ENERGY STAR qualified multifunction device. The International ENERGY STAR ® Office Equipment Program is an international program that promotes energy saving through the penetration - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 4
of the printer. The following symbols are found throughout the USER'S Manual and have the following meaning: WARNING This WARNING mark means that there or serious injury if you ignore or do not follow the said instruction. CAUTION This CAUTION mark means that there is a possibility of injury or - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 5
the wall outlet as possible. 4. If you wish to move the printer, please contact your service personnel. 1. Do not remove the screw and do not open the cover if not instructed to do so in this User's Manual. If you ignore this warning, you may be burnt or receive an electric shock due - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 6
CAUTION Do not install the printer in a humidified room or a dusty room. Also, do not install the printer on an unstable floor as injuries may occur. 1. Unplug the printer before you move it. The power cord may be damaged and it may result in a fire or electric shock. 2. If you do not use the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 7
POWER CORD INSTRUCTION The installation of (or exchange to) a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 8
6. 2 Keeping the paper in the custody 1. 6. 3 Treatment against environmental condition 1. 7 Specifications for Scan Original (KIP 860 only) 1. 7. 1 Original - Standard 1. 7. 2 Special Documents 1. 7. 3 "Do Not Scan" Originals 1-1 Page 1- 2 1- 3 1- 4 1- 5 1- 5 1- 7 1- 8 1- 8 1- 9 1- 10 1- 11 1- 12 - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 9
must be leveled and the floor strength must be ample to sustain the weight of the equipment. 2,040mm (When connecting optional Auto Stacker) 1,200mm Rear KIP 800Series 650mm Left HardwCare Right Front 1,500mm 1-2 Chapter 1 Before Use - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 10
1. 2 Originals Prohibited from Duplication It may be illegal to duplicate or copy certain types of originals and you may be punished by local or regional laws, if copies are made of these types of originals. Please be aware of your local or regional laws and which originals they forbid you to - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 11
(1) KIP 800 Series is an Electro Photographic full color and B&W LED printer / MFP. (2) Selection from 3 models are available according to the requirement. - KIP 850 : 2 rolls digital printer model - KIP 860 : 2 rolls MFP model (Single footprint) - KIP 870 : 4 rolls digital printer model - KIP 880 - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 12
KIP 800 Series - KIP 850 : 2 rolls digital color and B&W printer - KIP 860 : 2 rolls digital color and B&W MFP (single footprint) - KIP 870 : 4 rolls digital color and B&W printer - KIP 880 : 4 rolls digital color (AC) Automatic (4 or 2 rolls) and manual bypass 220 to 240V (+6% to -10%), 20A - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 13
can vary by scanner model connected Bond/Plain paper - 70 to 90 g/m2 (Color and monochrome : 80mm /sec.) - 90 to 160g/m2 (Heacy media is used : 50mm / sec.) Film - g/m2 Gloss - g/m2 PLEASE SEE THE KIP 800 MEDIA GUIDE FOR DETAILS Standard Environment : 23oC and 60% Temperature 10 to 30 degrees - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 14
1. 4. 2 Scanner (KIP 860) Subject Scanning method Light source Scanning speed (600 dpi, normal quality) (max) Specification Contact Image Sensor (CIS) (5 pieces of A4 sized CIS) LED (R/G/B) Monochrome : 65mm/s Grayscale : 65mm/s Color : 22mm/s Setting of original Starting point of scan - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 15
Read the original with this unit when you make scan or copy. (KIP 860 only) While scanning: emergency stop At Standby position: eject Starts can be loaded here. LED indicator indicates the following printer status. Color Green Green Orange Red Blue Blue light purple Condition Light Blink Light - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 16
1. 5. 2 Left side view 1 5 2 3 4 5 6 Name of part Function 1 Toner Cartridge 4 Toner Cartridges (cyan, magenta, yellow and black) supplies the toner little by little. 2 Media Feeding When the paper jam occurs, the media is fed by rotating this knob. Knob 3 Unlock Lever When the paper - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 17
1. 5. 3 Right side view 1 2 Name of part 1 USB Port 2 Power Switch Function Your USB flash memory storage can be installed here. 5VDC max. Turns on/off the Printer. 1-10 Chapter 1 Before Use - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 18
1. 5. 4 Rear view 1 2 3 4 5 6 Name of part 1 Fuser Knob 2 Upper Exit Unit 3 Fuser Cover 4 Breaker 5 Stacker Port 6 Inlet Socket Function Rotate this knob when removing the misfed paper in the Fuser Unit. It ejects prints upward or backward. Prints come from the opening on this. Open the Fuser - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 19
1. 6 Specifications for Print Media 1. 6. 1 Papers not available to use Do not use the following kinds of printing paper. Doing so may damage the print engine. Excessively curled (a diameter of 50 mm or less) Folded Creased Torn Punched 1-12 Chapter 1 Before Use - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 20
Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film CAUTION Do not use the paper with staple, or do not use such conductive paper as aluminium foil and carbon paper. The above may result in a danger of fire NOTE (1) Print image may become light if printed on a rough - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 21
tracing paper. "Void of image" occurs when you print with plain paper and tracing paper. "Void of image", "crease of paper" and other problems occurs when you print with plain paper and tracing paper. Necessary treatment 1. Install the humidifier in the room, and humidify the room air. 2. Remove - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 22
1. 7 Specifications for Scan Original (KIP 860 only) A scan original must satisfy the following specifications. Thickness Width Length 0.05mm to 1.60mm 210mm to 914.4mm 210mm to 6,000mm NOTE : 1. Image quality - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 23
1. 7. 3 "Do Not Scan" Originals It is impossible to use the following types of originals because they are likely to damage the scanner. Do not scan the following kinds of original, because you may damage the original or scanner itself! Sticked with paste Paste Torn Folded (Leading edge) So much - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 24
Not square Wet image Made of metal or fabric Rough surface (Carbon paper for example) Clipped or stapled Metal Wet Fabric Rough surface Clipped Stapled 1-17 Chapter 1 Before Use - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 25
The following kinds of originals can be read with using a carrier sheet. However, the image quality and feed reliability are not guaranteed. Patched Punched 1-18 Chapter 1 Before Use - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 26
Chapter 2 Basic Operations 2. 1 Turning on the Printer 2. 2 Turning off the Printer 2. 3 Replacing the Roll Media 2. 4 Placing Cut Sheet Media 2. 5 Replacing the Toner Cartridge 2. 6 Replacing the Waste Toner Box 2. 7 Copying (for KIP860) 2. 8 Stop of Scan or Copy (for KIP860) 2-1 page 2- 2 2- 4 - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 27
2. 1 Turning on the Printer 1. Plug the Printer to an exclusive wall outlet. NOTE Please confirm the outlet satisfies the following condition before plugging the Printer into. 220-240V (+6% to -10%), 20A, and 50/60Hz 2. Press "|" side of the Power Switch. Press this side 3. The Status Indicator - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 28
4. The Printer will get ready about 6 minutes after turning on. The Status Indicator stops blinking and lights green when ready. Make a copy or print from outer devices. 2-3 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 29
2. 2 Turning off the Printer 1. Press " " side of the Power Switch. Press this side 2. The Status Indicator flashes light purple while the embedded controller unit is shutting down. It will turn off in few minutes. Status Indicator (blinking) NOTE The controller unit starts shutdown process after - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 30
3. If you completely shut the power supply due to a long vacation or the machine's transport, turn off the circuit breaker and then remove the power cable from the machine. 2-5 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 31
green lever (4) on each Flange (2), which releases the core of roll (3). Remove both Flanges (2). 3 4 2 2 2 3. With sliding the Slide Guides (5) left and right by hand, align them to the width guide lines that match the width of actual media to be loaded. (Sliding either left or right one of 2 Side - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 32
4. Insert both Flanges (2) deep into the core of new roll media until they stop. 2 NOTE (1) Insert Flanges (2) deep enough into the core of roll media until their inside rims surely touch the side face of roll media with having no gap. Inside Rim OK Inside Rim NG Gap Correct: Fully inserted - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 33
5. Turn down the lever (4) in either way until they completely stop, which lets the Flange to surely hold the roll media. 4 4 6. Fit both Flanges correctly into both Slide Guides (5) in the roll deck. 5 (See next page for more explanation) 2-8 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 34
NOTE (1) Note the position of leading edge. It should be on the bottom side when directed to the media feeding path. Correct Incorrect to media feeding path to media feeding path Correct: Leading edge is on bottom side Incorrect: Leading edge is on top side (2) The outside rim (7) of the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 35
7. Insert the leading edge into a slit under the Guide Plate (9) until it touches the feeding roller (10). Front Deck (Roll 1 / 3) Rear Deck (Roll 2 / 4) 9 9 10 9 10 Roll 1 10 Roll 3 10 9 10 Roll 2 10 Roll 4 2-10 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 36
8. Rotate the small green roller (11) in the direction of arrow by hand for allowing the feeding roller to surely hold the leading edge. Front Deck (Roll 1 / 3) Rear Deck (Roll 2 / 4) 11 11 Roll 1 10 10 Roll 3 9. Push the Roll Deck (1) back in. Roll 2 Roll 4 1 1 NOTE (1) Surely close the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 37
Table which indicate possible feed positions. Place a cut sheet in a required size on the table between its concerning size markings then i nsert it into Manual Feeder. When the leading edge touches the feeding roller, the machine automatically carries and sets the sheet at the proper position - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 38
(2) in the arrow direction until it stops. Pull and remove the empty Toner Cartridge. 2 2 NOTE The Toner Cartridge should be returned to your service technician or should be discarded according to your local regulations. WARNING Do not discard it as a flammable. Toner will explode if thrown into the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 39
in the direction of arrow for more than 3 revolutions. This will have a space in the toner supplying hole. 5. With directing the pointed tip (4) of the color label upside, set the new Toner Cartridge back into the original position and insert it deep into the machine until it stops. 4 Direct the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 40
6. Rotate the Toner Cartridge (3) in the arrow direction until it stops. 3 7. Close the Left Side Cover (1). When the Left Side Door is closed; The machine goes into "warm up" while processing toner supply. The machine gets "ready" when the toner refilling completes. 1 2-15 Chapter 2 Basic - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 41
2. 6 Replacing the Waste Toner Box 1. Follow the figures in below to assemble a new Waste Toner Box. Sticker (Large) Sticker (Large) Sticker (Small) Stickers (Small) Reference A sheet of Sticker (Large) still remains after assembling the new Waste Toner Box. This is to be used to close the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 42
handle the Waste Toner Box roughly. Otherwise the toner will come out from its open hole. (2) The Waste Toner Box should be returned to your service technician or should be discarded according to your local regulations. 2-17 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 43
5. Set the new Waste Toner Box (4) back in the original position. See the following NOTE. 4 NOTE (1) Place the bottom corner of the box at the inside of the positioning step (5). 4 5 (2) Make sure the clear film windows (6) is not dirty. 6 2-18 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 44
6. Close the Left Side Cover (1). 1 2-19 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 45
original width. 1 1 3. Place the original on the Original Table with face up. Then insert it under the Scanner Unit along with Original Guides. When the leading edge touches the original feeding roller, the machine automatically carries and sets the original at the proper position. 2-20 Chapter - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 46
4. The KIP 860 will start the copy process. Reference Pressing START button may be required to start the scan according to the scanner's controller software. For further - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 47
The KIP 800 Series has 2 print delivery system, the print tray / rear stacking equipment. NOTE For the front stacking, gently lift ", remove all the prints on the print tray. For further information of switching front / back delivery, see KIP Multi-Touch User Guide. 2-22 Chapter 2 Basic Operations - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 48
2. 8 Stop of Scan or Copy (for KIP860) 1. If necessary, press the Scan Abort Button on the Scanner Unit to immediately stop the original while making a copy or scan. Scan Abort Button Pressing the button stops the current reading a document immediately. The current printing is stopped as well and is - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 49
Roll Deck Section Jam (Deck 1,2, 3, 4 Mis-feed) 3. 1. 2 Manual Feeder Section Jam (Registration Mis-feed) 3. 1. 3 Media Feed Section Jam Replacement 3. 3. 2 Toner Empty 3. 3. 3 Waste Cartridge full 3. 3. 4 Web Cleaner Empty 3. 4 Service Call Error page 3- 2 3- 3 3- 5 3- 6 3- 8 3-11 3-12 3-13 3-13 - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 50
displaying "Mis-feed" is shown below. Fuser Section Fuser Mis-feed Media Feed Section Registration Mis-feed Media Feed Section Separation Mis-feed Manual Feeder Section Registration Mis-feed Fuser Section Fuser Mis-feed Roll Deck Section Roll Deck Section Deck 2 Mis-feed Deck 1 Mis-feed Deck - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 51
3. 1. 1 Roll Deck Section Jam (Deck 1, 2, 3, 4 Mis-feed ) Roll Deck Section Roll Deck Section Deck 2 Mis-feed Deck 1 Mis-feed Deck 3 Mis-feed (for KIP870) Deck 4 Mis-feed (for KIP870) Clear the Paper Mis-feed using the following procedure: 1. Open the Roll Deck (1) in issue. And then rewind the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 52
the roll media correctly. Front Deck (Roll 1 / 3) Rear Deck (Roll 2 / 4) NOTE The outside rim of Flange should meet the black triangle marked on Slide Guide. Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding. OK NG Out of position Correct 4. Close the Roll - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 53
Section Registration Mis-feed 1. Pull out the mis-feed cut sheet from the Manual Feeder. NOTE The mis-feed cut sheet should be replaced with a new one if its leading edge has a torn or fold. Or it should be - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 54
3. 1. 3 Media Feed Section Jam (Registration Mis-feed, Separation Mis-feed) Media Feed Section Separation Mis-feed Media Feed Section Registration Mis-feed 1. Open the Left Side Cover (1). 1 2. Turn the Lever (2) to the arrow direction. 2 2 3-6 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 55
3. Remove the jammed media. 4. In case that the media is pinched by the roller and cannot be removed, rotate the Paper Feeding Knob (3) to feed the media to the Feeder Unit, and then remove it. 3 3 3-7 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 56
3. 1. 4 Fuser Section Jam (Fuser Mis-feed) Fuser Section Fuser Mis-feed 1. Open the Fuser Cover (1). 1 3-8 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 57
2. Holding the knob (2) on both sides, lift up the Separation Finger Assy (3) until the hook (4) catches the shaft (5). 3 2 2 4 5 3-9 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 58
3. Rotate the Fuser Knob (6) to the arrow direction to feed the media to the exit direction, and then remove it. 6 WARNING There are extremely hot parts inside the Fuser Unit. Do not touch any parts in the Fuser Unit, or you will be burnt. Also the mis-fed media can be very hot. Be careful not to - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 59
3. 1. 5 Upper Exit Part Jam (Exit Part Mis-feed) Upper Exit Part Exit Part Mis-feed 1. Remove the Exit Tray 2 (1). 1 2. Open the Upper Exit Unit (2) and then remove mis-feed paper (3). 2 3 3-11 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 60
3. 1. 6 Original Jam (for KIP860) If an original is mis-fed while scanning, the UI screen shows "Original Jam". Follow the instruction below to remove the mis-fed original. 1. Lift up both sides (1) of the Scanner Unit 1 2. Remove a mis-feed original. 3. Gently press the Scanner Unit down - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 61
3. 2 Door Open "Door Open" is displayed in the UI screen when the door in each unit is opened. 3. 2. 1 Roll Deck (Deck 1 Open, Deck 2 Open) Close the Roll Deck securely to clear "Deck 1 Open" or "Deck 2 Open". Roll Deck 3. 2. 2 Left Side Cover (Left Side Cover Open) Close the Left Side Cover - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 62
3. 2. 3 Fuser Cover (Fuser Cover Open) Close the Fuser Cover securely to clear "Fuser Cover Open". Fuser Cover 3. 2. 4 Upper Exit Unit (Paper Exit Door Open) Close the Upper Exit Unit securely to clear "Paper Exit Door Open". Upper Exit Unit 3-14 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 63
3. 3 Other Operator Call 3. 3. 1 Roll Replacement When the printer is running out of a loaded roll media, the UI Screen will display "Out of Paper" sign. If there is no suitable roll media required for the current print job, the UI Screen will display "Out of Paper" sign as well. Please load the - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 64
". (The Printer is still available) "Out of Web" error will appear over a period of time, and the Printer becomes unavailable. Please call your service representative to replace Web Cleaner early. NOTE Web Cleaner can be replaced by a well trained technician only. 3-16 Chapter 3 Error Correction - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 65
, and its equivalent internal code) on the UI screen. Call the service staff immediately as these problems can be fixed by a well trained technician only. Before calling the service staff, try to turn on/off the Printer. If "Service Call Error" is indicated again, turn off the machine, unplug it - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 66
Chapter 4 Maintenance 4. 1 Scanner Unit (KIP 860 only) 4. 1. 1 Scan Glass, Feed Roller, Guide Plate 4. 1. 2 Sensor 4. 2 Touch Screen 4-1 page 4- 2 4- 2 4- 5 4- 7 Chapter 4 Maintenance - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 67
It is recommended to clean each Scan Glass, Feeding Rollers and Guide Plates as the scan/copy image may become defective if these parts are dirty. NOTE For ease of visual check, this document shows the Upper - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 68
3. Gently wipe the Scan Glass (2) and Feed Rollers (white) (3) with a soft cloth. Equal mixture of water and neutral detergent can be used. 2 3 NOTE Do not use organic solvent, glass cleaner and anti-static spray for the cleaning. 4. Wipe the Feed Rollers (rubber) (4) with a dry cloth. 5. Wipe - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 69
6. Wipe the Upper Guide Plate (5) and the Lower Guide Plate (6) with a dry cloth. 5 5 6 7. Gently press Scanner Unit down and firmly close it. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing only one side down. 4-4 Chapter 4 Maintenance - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 70
4. 1. 2 Sensor If Sensors are dirty, the original may be detected incorrectly. Perform cleaning or as needed. NOTE For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1. Turn off the Printer. 2. Lift up both sides (1) of the Scanner Unit. 1 1 4-5 Chapter 4 - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 71
3. Gently wipe Sensors (2) with a dry cotton bud. 2 2 2 2 2 2 2 NOTE Do not use water, organic solvent, glass cleaner or antistatic spray for cleaning. 4. Gently press Scanner Unit down and firmly close it. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing - Konica Minolta KIP 800 Color Series | KIP 800 Series Hardware Operation Guide - Page 72
4. 2 Touch Screen 1. Wipe the Touch Screen with a dry cloth. NOTE Do not use water, alcohol, organic solvent and glass cleaner for the cleaning. 4-7 Chapter 4 Maintenance
KIP 800
| Color Series
Hardware Operation Guide
Version A.0