Kyocera ECOSYS FS-1370DN PRESCRIBE Commands Command Reference Manual Rev 4.9
Kyocera ECOSYS FS-1370DN Manual
View all Kyocera ECOSYS FS-1370DN manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera ECOSYS FS-1370DN manual content summary:
- Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 1
PRESCRIBE Commands Command Reference - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 2
or errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in the printer's firmware. Regarding Tradenames: PRESCRIBE is a registered trademark of Kyocera Corporation - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 3
printers, you need to acquire a multi-user license agreement which can be obtained from Monotype Imaging. Monotype Imaging retains all rights, title and interest to the Software Monotype Imaging does not warrant that the Software is free from all bugs, errors and omissions. 8. THE PARTIES AGREE THAT - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 4
This page is left blank intentionally iv - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 5
11 ACLI - Add CoLor by Index 12 ALTB A - [ALlocate TaBle] Assign user-defined character table --------- 14 ALTB C - [ALlocate TaBle] Convert character code 15 ALTB D - [ALlocate TaBle] Delete user-defined character table --------- 16 ALTB E - [ALlocate TaBle] End defining combination characters - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 6
82 DUPX - select/deselect DUPleX mode 84 DXPG - select DupleX PaGe side 85 DZP - Draw to Zero-relative Position 87 EMCR - Enable MaCRo depending on paper source 89 ENDB - END a two-dimensional Barcode string 91 ENDC - END carbon Copy 92 ENDD - END Dump 93 ENDM - END Macro 94 ENDR - END - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 7
PMZP - in Path, Move to Zero-relative Position 205 PNCH - PuNCH 207 PRBX - in Path, draw Round BoX 209 PRRC - in Path, at Relative position, draw aRC 211 PSRC - select Paper SouRCe 213 PXPL - PiXel PLacement 214 !R! - PRESCRIBE start sequence 215 RCLT - Rotated CoLlaTion 217 RDMP - Received - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 8
- Set Bottom Margin 264 SCAP - Set line CAP 266 SCCS - Save Current Code Set 268 SCF - Save Current Font 270 SCG - Save Current Graphics state 272 318 SPL - Set Page Length 320 SPO - Set Page Orientation 322 SPSZ - Set Paper SiZe 324 SPW - Set Page Width 326 SRM - Set Right Margin 328 SRO - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 9
Mailbox ALias 357 VMOB - Virtual Mailbox Output Bin 358 VMPW - set Virtual Mailbox PassWord 359 WIDE - set WIDE A4 mode 361 WRED - WRite EnD 362 XBAR error correction level by percentage 367 XBCP 3 - set error correction level 368 XBCP 4 - set data code word rows 369 XBCP 5 - set data code - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 10
Contents-vi - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 11
PRESCRIBE Command Reference - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 12
this section list all the printing system commands supported by the various models. Support for certain commands varies depending on the printing 287 SIR Set Image Refinement level 304 SPSZ Set Paper SiZe 324 STAK select paper STAcKer 335 STAT STATus 336 TRSM TRansparency Separate Mode - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 13
326 SRM Set Right Margin 328 STM Set Top Margin 338 Margins and page orientation are more fully explained in Section 1.3. of the Technical Reference manual. 3 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 14
17.3 cm 6.8 inch 2,047 dots 17.3 cm 6.8 inch Default value 6 lpi 0.423 cm 0.167 inch 10 cpi 0.254 Additionally, there are commands to download fonts to the printing system from user-defined character table 14 ALTB C [ALlocate TaBle] Convert character code 15 ALTB D [ALlocate TaBle] Delete user - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 15
SCCS Save Current Code Set 268 SCF Save Current Font 270 SETF SET alternate Font 288 SFA Set bitmap Font Attributes 290 SFNT Select current FoNT by typeface 294 TPRS Text PaRSing 351 Fonts are more fully explained in Chapter 4 of the Technical Reference manual. Cursor Movement - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 16
by removing some of the downloaded fonts or by simplifying the graphic. To determine current memory usage, refer to a status page. Command Function Page ARC draw filled-in ARC 28 BLK draw filled-in BLocK 40 BOX draw BOX 42 CIR draw CIRcle 52 DAP Draw to Absolute Position 73 DPAT - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 17
203 PMZP in Path, Move to Zero-relative Position 205 PRBX in Path, draw Round BoX 209 PRRC in Path, at Relative position, draw aRC 211 RPG Return to Previous Graphics state to a palette, and specify colors. In this manual, color commands are marked with COLOR under the command name. 7 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 18
PRESCRIBE Command Reference Command Function Page ACLI Add CoLor by Index 12 CID Configure color-Image Data 50 CMOD Color MODe 60 CPAL Control PALette 63 GRAY represent GRAY 124 GRRD GRaphic data ReaD 125 HUE adjust HUE 127 LGHT adjust LiGHTness 155 MCLR Match CoLoR 159 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 19
Overview of PRESCRIBE Commands by Function Command Function Page DAM Delete All Macros 72 DELM DELete Macro 76 EMCR Enable MaCRo depending on paper source 89 ENDC END carbon Copy 92 ENDM END Macro 94 MCRO define MaCRO 160 Debug Commands These commands can be used to check the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 20
systems. The commands below provides access to the optional equipment. Command Function Page APSG Assign Paper Source Group 27 ASTK Assign STacKer trays 32 BKLT print in BooKLeT binding 38 CSTK 357 VMOB Virtual Mailbox Output Bin 358 VMPW set Virtual Mailbox PassWord 359 10 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 21
or by pressing the panel keys. The User's Manual provides a full description of the control panel functions. Many PRESCRIBE commands can be embedded commands within word processing software. This support depends upon the emulation mode and the software. See Emulation of the Technical Reference - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 22
PRESCRIBE Command Reference ACLI - Add CoLor by Index COLOR Format ACLI index, color1, color2, color3; Parameters index: integer from 1 to 255 color1: value for red, integer from 0 to 255, in RGB color space value for lightness, number from 0.0 to 100.0, in L*a*b color space color2: value - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 23
File !R! RES; DAM; UNIT C; SFNT 'AntiqueOlive-Bd', 20; CPAL C; SPAL 1; CID 0, 1; ACLI 1, 0, 0, 255; ACLI 2, 0, 255, 0; ACLI 3, 255, 0, 0; MZP 1, 1; SCOL 1; TEXT 'This line is printed in blue.'; MZP 1, 2.4; SCOL 2; TEXT 'This line is printed in green.'; MZP 1, 3.8; SCOL 3; TEXT 'This line is printed - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 24
Command Reference ALTB A - [ALlocate TaBle] Assign user-defined character table Format ALTB A, table-id; Parameter table-id: number identifying the character table assigned to the resident font, from 1 to 65535 Function The ALTB A command assigns the user-defined character table to the current - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 25
= 0 to 65533, or in hexadecimal notation ($xxxx). Function The ALTB C command converts the character code given as source-character to the character code given as target-character in the user-defined character table. If the character table having the identical number already exists, the existing - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 26
-id: number identifying the character table, from 1 to 65535, to be deleted Function The ALTB D command deletes the character table defined by the user. If the table to be deleted is currently allocated to the resident font (see ALTB A), terminate the allocation by using ALTB R before deleting. It - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 27
] End defining combination characters Format ALTB E; Parameter None Function This command signals the end of defining combination characters in an already generated user-defined character table which was started by the ALTB S command. (page 20). The registered combined characters can be printed by - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 28
id, table-format; Parameters table-id: table ID number: 1 to 65535 table-format: 1 = 1-byte, character codes 0 to 255 2 = 2-byte, character codes 0 to 65533 Function The ALTB G command generates a user-defined table in either 1-byte or 2-byte format. If the same table ID number already exists, the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 29
table-id; Parameter table-id: number identifying the character table to be released Function The ALTB R command terminates the assignment of the user-defined character table for the current resident font. It is also possible to terminate the assignment of all userdefined character tables by using - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 30
table-id: number identifying the character table to define the combination character, from 1 to 65535 code: character code for which the combination character is defined. 1-byte code = 0 to 255; 2-byte code = 0 to 65533, or in hexadecimal notation ($xxxx). width: overall width of the combined - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 31
TaBle] define combined character by Table Format ALTB T, character-code, width, height, x-coordinate, y-coordinate; Parameters code: character code for which the combined character is defined, or hexadecimal notation ($xxxx), JIS code width: character width: the value from 1 to the character - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 32
PRESCRIBE Command Reference File !R! res; unit c; SFNT 'TimesNewRoman', 48; ALTB G, 1000, 1; ALTB A, 1000; ALTB S, 1000, 64, 1800, 1000; ALTB T, 77, 700, 700, 0, 700; CMNT M; ALTB T, 65, 700, 700, 630, 700; CMNT A; ALTB T, 85, 700, 700, 1050, 700; CMNT U; ALTB T, 73, 700, 700, 1570, 700; CMNT I; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 33
ALTF ALTF - change to ALTernate Font Format ALTF alternate-number; Parameter alternate-number: a number from 0 to 47 Function The ALTF command changes the current font to a font designated by an alternate number. The actual font assigned to this alternate number is set by a previous SETF - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 34
PRESCRIBE Command Reference File !R! RES; SFNT "Helvetica-Nr", 12, 1000; SFNT "TimesNewRoman-It", 11, 1001; SETF 1, 1000; SETF 2, 1001; MCRO BIBLIO; ALTF 1; TEXT %1, E; TEXT " ", E; ALTF 2; TEXT %2, E; TEXT " ", E; ALTF 1; TEXT %3, N; ENDM; ALTF 1; TEXT "Bibliography", N, U; TEXT, N; CALL BIBLIO, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 35
to print multiple copies of the same form, filled in with different text. The AMCR command closely resembles the CALL command; therefore, the user should refer to the section on the CALL command for further information. When the automatic macro is enabled using mode E, the following printing system - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 36
PRESCRIBE Command Reference File !R! RES; MCRO CROPMARK; UNIT C; MZP 2.46, 3.96; SCP; SCP; SCP; MRP -.635, 0; DRP -1.9, 0; RPP; MRP 0, -.635; DRP 0, -1.9; RPP; MRP 14.85, 0; SCP; SCP; MRP .635, 0; DRP 1.9, 0; RPP; MRP 0, -.635; DRP 0, -1.9; RPP; MRP 0, 21; SCP; SCP; MRP .635, 0; DRP 1.9, 0; RPP; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 37
sizes and types. If the automatic paper selection feature of the printer driver is used, APSG is disabled. To utilize paper source grouping, the paper source must be explicitly commanded by the printer driver. Example To set six paper cassettes into group 1 (cassettes 1 and 4), group 2 (cassettes - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 38
PRESCRIBE Command Reference ARC - draw filled-in ARC Format ARC inner-radius, outer-radius, start-angle, end-angle; Parameters inner-radius: inner radius of arc outer-radius: outer radius of arc start-angle: starting angle end-angle: ending angle Function The ARC command works in the standard - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 39
ARC File !R! RES; UNIT C; MAP 5, 8; PAT 52; ARC 1, 2, -45, 45; MAP 5, 10; PIE 2, 0, 10, 20, 30; ARC 0, 2, 0, 60; PAT 20; ARC 0, 2, 60, 180; PAT 10; ARC 0, 2, 180, 360; PAT 1; NEWP; PMZP 4, 2; PARC 4, 3, 1, 90, 270; PARC 5, 4, 1, 180, 360; PARC 6, 3, 1, 270, 90; PARC 5, 2, 1, 0, 180; STRK; MRP 0.6, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 40
PRESCRIBE Command Reference Printout Related Command PARC 30 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 41
resident font. The external characters should be generated and downloaded in the printing system as an external font by using the LDFC or LDFN command. For the print systems supporting 2-byte font system, if the user-defined font is a 1-byte code font, it is assigned to the current resident roman - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 42
groups so that the sorter can be shared among the multiple users. Each parameter represents the last tray in each group of must be equal to the number of the trays the sorter is equipped with. By the factory default, the trays are grouped as the following table: Group 1 2 3 4 5 Equiv. ASTK - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 43
ASTK File The following command sequence delivers print jobs to trays 4, 5, 6, and 7 (the second group). !R! FRPO S0, 1; CMNT Enter multiple sorter mode; ASTK 3, 7, 9; CMNT Create three groups; MID 2; CMNT Send the output to 2nd grp.; SSTK; CMNT Sort; EXIT; Related Commands CSTK, MID, MSTK, SSTK 33 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 44
five with no check digit 22 =Identicon two of five with no checksum 23 = Code 128 (manual mode change) 24 = Code 128 (auto mode change) 25 = Code 11 with only 'c' 26 = Code 11 with both 'c' and 'k' checksum 27 = Code 93 with both 'c' and 'k' checksum 28 = CODABAR with no check digit (narrow gap) 29 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 45
BARC 43 = CUSTOM CODE (Japan)1 44 = CODABAR with no check digit ( types that have bars in two different heights. Height of all bars in other cases. Default value is 1.52cm (0.6 inches, 180 dots). The unit of measurement is determined by the the table below. 1 FS-600/FS-7000/FS-9100/FS-9500 only 35 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 46
PRESCRIBE Command Reference Table 20 Characters that can be used Type Max Characters to be used Default 0 11 0123456789 0 1 13 0123456789 0 2 16 0123456789 0 3 13 0123456789 0 4 18 0123456789 0 5 22 0123456789 0 6 25 0123456789 0 7 29 0123456789 0 8 6 0123456789 0 9 8 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 47
1 - 20 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ 44 3 - 32 $+-./0123456789:abcdetn* and spaces Default 0 0 - Length of the bars For the UPC and EAN ( use the dot for the unit of width in order to avoid the translation error by the barcode reader. The example below specifies the width of the first bar - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 48
must be defined using the JOBS command. Used together with the FOLD command, the paper can be folded in the middle to form a booklet. Booklet printing is possible for command page in this manual. The document must have the same page size for all pages. If the double size paper for the document is - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 49
reading pages from right to left This command is not supported by some photocopier models. The following command sequence prints document in booklet mode, folding the stack in the middle. The printing system will require A4-R paper to be loaded. !R! RES; SPSZ 8, 5; UNIT C; BKLT 1; DUPX 2; FOLD; SFNT - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 50
-in BLocK Format BLK width, depth[, option]; Parameters width: width of the block depth: depth of the block option: B = Leave the cursor unmoved (Default) H = Move the cursor to the horizontally adjacent corner V = Move the cursor to the vertically adjacent corner E = Move the cursor to the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 51
RES; UNIT C; MAP 5, 5; PAT 20; BOX 4, 1; BLK 4, 1; MRP 0, 1.5; BOX 4, 1; BLK 4, 1; MRP .9, .6; SFNT "Helvetica-Nr"; TEXT 'OVERPRINTING'; MRP 0, 5; PAT 29; BOX 1, -4; BLK 1, -4, H; PAT 39; BOX 1, -3; BLK 1, -3, H; PAT 49; BOX 1, -2; BLK 1, -2, H; PAT 59; BOX 1, -1; BLK 1, -1, H; PAGE; EXIT; Printout - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 52
PRESCRIBE Command Reference BOX - draw BOX Format BOX width, depth[, option]; Parameters width: width of the box depth: depth of the box option: B = Leave the cursor unmoved (Default) H = Move the cursor to the horizontally adjacent corner V = Move the cursor to the vertically adjacent - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 53
BOX MAP 4, 0; SCP; SFNT "Helvetica-Nr", 10; BOX 4, 2, L; TEXT 'Text printed with option L'; RPP; BOX 4, 2, N; TEXT 'Text printed with option N'; PAGE; EXIT; Printout 43 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 54
PRESCRIBE Command Reference CALL - CALL macro Format CALL[ repeat-count] macro-name, parameter-value, ...; Parameters repeat-count: number of times the macro is to be executed macro-name: name defined by a MCRO command parameter-values: values given to the dummy parameters in the macro - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 55
File !R! RES; UNIT C; SLS .5; CMNT Requires BX and SCREEN macros; CMNT See ENDM command page; MAP 9, 3; CALL BX; MAP 7, 4; CALL 5 BX; MAP 5, 5; CALL 9 BX; MAP 8, 6; CALL SCREEN, 2.2, 1.7; MAP 8.6, 7; TEXT 'Narrow', L; TEXT 'screen'; MAP 5,9; CALL SCREEN, 8.2,1.2; MAP 8,10; TEXT 'Wide screen'; PAGE; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 56
paper sources, enabling to apply the different form overlay using the different paper The macro and paper source for each page on the paper fed from cassette to the page. Note that the same paper source as the previous line is applied to is not possible. The paper size and the page orientation - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 57
COPY; UNIT C; SFNT 'Helvetica-Bd',14; TEXT "Client's Copy", L; SFNT 'Helvetica', 9; TEXT 'Please retain this copy for future reference.'; MRP 0, .2; BOX 6, 1; MRP 0, .35; TEXT ' Registered Client'; ENDM; CCPY E; PSRC 1; AMCR E,COVER; TERM; PSRC 0; AMCR E,MAIL; TERM; PSRC 1; AMCR E,COPY; TERM; ENDC - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 58
PRESCRIBE Command Reference Printout 48 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 59
CDSK CDSK - Check hard DiSK Format CDSK; Parameter None Function The CDSK command verifies data in the hard disk (garbage collection). It deletes garbage jobs such as page image data that were accidentally generated in the hard disk and normally inaccessible for deletion. File !R! CDSK; EXIT; 49 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 60
Data COLOR Format CID color-space, encoding; Parameters color-space: 0 = Device-dependent RGB (Default) 1 = Device-dependent CMY 2 = Void 3 = CIE L*a*b encoding: Pixel encoding 1 = Indexed by Pixel (Default) 3 = Direct by Pixel Function The CID command creates a new color palette using the ID - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 61
CID File !R! RES; DAM; UNIT C; SFNT 'Helvetica-Bd', 20; CPAL C, 1; SPAL 1; CID 0, 1; CMNT RGB Color Space used; ACLI 1, 0, 0, 255; MZP 1, 1; SCOL 1; TEXT 'An RGB color palette is used.' CID 3, 1; CMNT L*a*b Color Space used; ACLI 2, 100, 75, 0; MZP 1, 2; SCOL 2; TEXT 'An L*a*b color palette is used - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 62
PRESCRIBE Command Reference CIR - draw CIRcle Format CIR radius; Parameter radius: radius of the circle Function In standard graphics mode, the CIR command draws a circle centered at the current cursor position. The line thickness used is designated by the SPD command. A circle can also be - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 63
CIR Printout 53 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 64
PRESCRIBE Command Reference CLIP - CLIP current path Format CLIP [clip-mode]; Parameter clip-mode: 1: EO clip 2: Non-zero winding clip Function The CLIP command sets the current path as the clipped path. After this command is issued, no painting is done outside the area of the path. Executing - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 65
CLPR CLPR - CLiP Rectangular area Format CLPR [x1, y1, x2, y2]; Parameters x1: x coordinate of the top-left corner of the rectangle y1: y coordinate of the top-left corner of the rectangle x2: x coordinate of the bottom-right corner of the rectangle y2: y coordinate of the bottom-right corner - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 66
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; SPD 1; PMRA 6, 9, 3, 0; PAT 1; PARC 6, 9, 3, 0, 360; CLPR 3, 6, 9, 12; STRK; PAGE; EXIT; Printout 56 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 67
CLSP CLSP - CLoSe Path Format CLSP; Parameter None Function The CLSP command closes an open path by adding a line segment extending from the end of the path to the beginning of the path. Simply ending a path at the path's starting point does not make it a closed path; such a path remains open until - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 68
PRESCRIBE Command Reference Printout Related Command NEWP 58 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 69
CMNT CMNT - CoMmeNT Format CMNT string; Parameter string: any character string Function The CMNT command adds a character string, typically a comment explaining the purpose of the following PRESCRIBE commands. The CMNT command statement will be ignored by the printing system. Although character - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 70
PRESCRIBE Command Reference CMOD - Color MODe COLOR Format CMOD mode; Parameter mode: color mode: 0 = Monochrome 1 = Color (Default) Function The CMOD command switches between monochrome and color modes. In monochrome mode, other color commands are still enabled, but printing is converted to - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 71
of copies Function The COPY command designates the number of copies for each page in a print job. This copy count value can be changed by sending the printing system another COPY command or by issuing a reset command. For best results, place the copy command near the start of a job or at - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 72
PRESCRIBE Command Reference Printout 62 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 73
already exists for another palette. The palette ID number is reset to 0 by RES command. Mode A deletes all existing palettes and brings the default palette back to the default state (ID 0). Note that non-active palettes are not deleted. Also, palette-id is not used when mode is A. Mode S deletes all - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 74
PRESCRIBE Command Reference CPTH - Character PaTH Format CPTH 'string'; Parameter string: any character string except from ASCII code 31 (hex 1F) and lower Function The CPTH command constructs a path which adds the outlines of characters to the current path. When stroked or filled, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 75
3R = PC Cyrillic* 3S = ISO 10 Swedish 4S = ISO 16 Portuguese 4U = Roman-9 5M = PS Math 5N = ISO Latin 5 5S = ISO 84 Portuguese 5T = ISO Windows Latin 5 6J = MS Publishing 6M = Ventura Math 6N = ISO8859/10 Latin 6 6S = ISO 85 Spanish 7J = Desktop 8G = Greek-8 8M = Math 8 8Q = PC Set 1 IBM - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 76
14R = PC Ukrainian 15U = Pi Font 16U = PC-857 17U = PC 852 18N = ISO-10646 18U = PC-853 Turkish/Latin 3 19L = Windows 3.1 Baltic† 19M = Symbol (Symbol-Set-SWM font only) 19U = Windows Latin 1 20U = PC-860 Portugal† 21U = PC-861 Iceland† 23U = PC-863 Canada-French† 24Q = PC-8 Polish Mazovia† 25U = PC - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 77
of alphabetic, numeric, and symbolic characters. The CSET command summons the symbol set to suit the various languages with the current font. The factory default symbol set is 0U (US ASCII). When the FSET command is used to select a font, the printing system selects a font based on a prioritization - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 78
: number from 1 to the maximum (bottom) Function The CSTK command is effective only when the optional sorter is installed to the printing system. It instructs the printing system to deliver printed pages to the sorter in the collator mode. Each tray specified receives all copies of one page. The - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 79
of the string is unlimited, except that the command as a whole may not be longer than 255 characters. Carriage-return and linefeed codes in the string are ignored. File !R! RES; SLPI 3; SFNT "Helvetica-Bd", 16; MAP 4, 1; CTXT 'NEWS!', L, U; SFNT "TimesNewRoman-It", 16; CTXT 'Unforgettable Holidays - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 80
PRESCRIBE Command Reference Printout 70 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 81
deletes all nonresident fonts and the font numbers assigned to scalable fonts by the SFNT command from the printing system's memory. This enables the user to make room for new fonts, macros, and graphics. File !R! UNIT P; SLS 16; SFNT 'Helvetica-Bd', 15, 2000, 277, 2, 0; SFNT 'Helvetica', 15, 2001 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 82
Function The DAM command deletes all macro definitions made by using the PRESCRIBE MCRO command from the printing system's memory. This enables the user to make room for new macros, fonts, or graphics. File !R! RES; UNIT C; CMNT Print ENDM file first.; SFNT "Helvetica-Bd"; MAP 5, 4; CALL SCREEN - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 83
DAP DAP - Draw to Absolute Position Format DAP x-coordinate, y-coordinate; Parameters x-coordinate: distance from the left margin y-coordinate: distance from the top margin Function The DAP command draws a line from the current cursor position to a position specified relative to the top and - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 84
PRESCRIBE Command Reference Printout 74 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 85
identifying the font to be deleted Function The DELF command deletes any designated non-resident font from the printing system's memory. This enables the user to make room for new fonts, macros, and graphics. The printing system's memory is large but not unlimited, and judicious use of the DELF - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 86
PRESCRIBE Command Reference DELM - DELete Macro Format DELM macro-name; Parameter macro-name: name defined by a previous MCRO command Function The DELM command deletes a specified macro definition from the printing system's memory to make room for new macros, fonts, or graphics, or so that the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 87
-.8; MRP 1, 0; ENDM; MCRO SCREEN %, width, depth; CMNT Draws box with rounded corners; CMNT Leaves cursor at previous position; SPD .08; SCP; MRP .25, .25; ARC .23, .30, 270, 0; MRP 0, -.25; DRP %1, 0; MRP 0, .25; ARC . - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 88
command. If you specify a value between 11 to 20 when no user pattern has been defined, the path will be stroked in solid black. The DPAT command does not affect the line drawn by the standard graphics commands such as DRP, BOX, ARC, etc. File !R! RES; UNIT C; MCRO DPAT; NEWP; SPD .2; SCP; SFNT " - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 89
DPAT Printout Related Command SDP 79 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 90
PRESCRIBE Command Reference DRP - Draw to Relative Position Format DRP x-coordinate, y-coordinate, ...; Parameter x-coordinate/y-coordinate: coordinates as measured from the current cursor position Function The DRP command draws a line from the current cursor position to a specified relative - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 91
DRP Printout Related Command PDRP 81 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 92
PRESCRIBE Command Reference DRPA - Draw to Relative Position specified by Angle Format DRPA length, angle; Parameters length: length of the line angle: angle in degrees, measured clockwise from the vertical Function The DRPA command draws a line of a specified length at a specified angle, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 93
DRPA Printout 83 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 94
2 = duplex mode, short-edge binding Function The DUPX command is effective only when the option duplexer is installed to the printing system. It instructs the printing system to select or deselect duplex printing and sets the binding mode. Portrait, long-edge Portrait, short-edge Landscape, long - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 95
printing system. It ends printing on the current page in the same manner as a form feed. However, unlike the form feed, it also selects the paper side, front or back, on which printing of the ensuing page is printed. The side parameter 1 prints the ensuing page begins on the front side - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 96
-down delivery; EXIT; This text prints right-side up on the front side of the page !R! DXPG 0; CMNT Ends current page (front side of the paper); EXIT; This text prints upside-down on the reverse side of the page !R! RES; EXIT; Printout This text points right side-up on the front - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 97
Function The DZP command draws a line from the current cursor position to a position specified relative to the top and left edge limits of the paper. The thickness of the line is designated by the SPD (set pen diameter) command. The coordinates and line thickness are measured in the value designated - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 98
PRESCRIBE Command Reference Printout Related Command PDZP 88 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 99
= print-side], [repeat-count] macro-name [, parameter...]; Parameters mode: E = enable automatic macro D = disable automatic macro paper-source: 0 = multi-purpose feeder 1 = cassette 1 (printing system's cassette) 2 = cassette 2 3 = cassette 3 4 = cassette 4 5 = cassette 5 6 = cassette 6 (bottom - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 100
Function The EMCR command allows separate auto macros to be assigned for each of the separate paper sources. In duplex printing, it is also possible to assign separate auto macros for both the the auto macro, use EMCR D. Note that EMCD D does not require other parameters such as paper-source. 90 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 101
18 is executed, it is used alone, without association with XBAR or XBUF. For details on two-dimensional barcodes, see Section 5.2. of the Technical Reference manual. 91 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 102
PRESCRIBE Command Reference ENDC - END carbon Copy Format ENDC; Function The ENDC command ends definition of the CCPY E command sequence. For details, refer to the CCPY command. 92 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 103
ENDD ENDD - END Dump Format ENDD; Parameter None Function The ENDD command ends a hexadecimal dump initiated by the RDMP (Received-data DuMP) command and returns to the PRESCRIBE command mode. File See RDMP on page 218. Related Command RDMP 93 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 104
ends a macro definition and returns to the PRESCRIBE command mode. File !R! RES; DAM; UNIT C; MCRO BX; SPD .05; BOX .8, -.8; MRP 1, 0; ENDM; MCRO SCREEN %, width, depth; CMNT Draws box with rounded corners; CMNT Leaves cursor at previous position; SPD .08; SCP; SCP; MRP .25, .25; ARC .23, .30 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 105
Printout ENDM Related Commands CALL, DAM, DELM, MCRO 95 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 106
PRESCRIBE Command Reference ENDR - END Raster data Format ENDR; Parameter None Function The ENDR command declares the end of raster data. To declare the start of raster data, a RVRD command is used. File The following example prints an illustrated crown using the RVRD and ENDR. !R! RES; DAM; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 107
ENDR 5, 0, 160, 96, 80, 0; 5, 1, 24, 1, 136, 0; 5, 14, 134, 6, 23, 0; 5, 48, 65, 248, 32, 192; 5, 192, 129, 8, 16, 48; 5, 0, 64, 144, 32, 0; 5, 0, 32, 96, 64, 0; 5, 0, 16, 0, 128, 0; 5, 0, 32, 0, 64, 0; 5, 0, 16, 0, 128, 0; 5, 0, 8, 1, 0, 0; 5, 0, 6, 6, 0, 0; 5, 0, 1, 104, 0, 0; 5, 0, 0, 144, 0, 0; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 108
; Parameter level: 0 = off 2 = on Function The EPL command switches the Ecoprint on or off (default). Ecoprint is a standard feature of the print systems that enables the user to reduce the amount of toner placed on the page which saves on printing costs. With EPL 2;, the printing image appears - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 109
EXIT EXIT - EXIT from PRESCRIBE mode Format EXIT [, E]; Parameter None Function When the printing system receives the EXIT command, it exits from the PRESCRIBE mode and treats the following information as characters to be printed. If the parameter E is added (EXIT, E;), the printing system ignores - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 110
mode is cassette or manual feed. Printing on A4 and letter size paper can only be done widthwise in first mode. This command causes a page break. This command is irrelevant to paper cassettes and envelope feeders. The paper orientation setting is restored to the default - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 111
FILL FILL - FILL closed path Format FILL rule; Parameter rule: drawing rule: 1 = use even-odd rule 2 = use non-zero winding number rule Function The FILL command fills the area enclosed by the current path with the current drawing rule. It also fills all independent subpaths contained in a path - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 112
PRESCRIBE Command Reference File !R! RES; UNIT C; SIMG 1; CMNT Drawing clusters; NEWP; PMZP 10, 12; PDRP -5.7, -1.75; PCRP 0, 0, 0, -3.4, 3.1, -3.6; CLSP; PAT 2; FILL; PMZP 10, 12; PDRP -2.6, -5.35; PCRP 0, 0, 2.5, -2.5, 4.9, .1; CLSP; PAT 3; FILL; PMZP 10, 12; PDRP 5.7, -1.75; PCRP 0, 0, 0, -3.5, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 113
FILL Printout 103 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 114
number values produce rougher curves and lower number values create smoother curves which require greater computation. The number actually specifies the maximum error tolerance of a straight line segment approximation of any portion of the curve. The printing system resets the flatness to 1 when it - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 115
FLST FLST - print Font LiST Format FLST; Parameter None Function The FLST command prints a list of all resident and downloaded (user-defined) fonts in the printing system. The list provides information on each font such as font name, whether it is scalable or bitmap, font selection - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 116
PRESCRIBE Command Reference Sample of Font List Internal Scalable and Bitmapped Fonts List PRESCRIBE Font Name Scalable/Bitmap Password Selection [FSET] Font ID 106 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 117
). With the staple value given, the pages are stapled (two) and folded at its center in reference to the short edge of the paper. Folding and stapling File Paper sizes available for this mode include A4-R, letter-R, B4, A3 and ledger. The job is automatically delivered on the face-down output tray - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 118
SFNT command, or a nonresident font generated by the LDFC command or downloaded from the computer. If an undefined font-number is specified, the font however, ignore the font mode setting. Line spacing must be specified by the user in this case using one of the line spacing commands (SLS, SLPI, etc - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 119
Printout Related Commands ALTF, FLST, SETF FONT 109 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 120
For printing system models that support 600/1200 dpi resolution printing, the default resolution generated by the FPAT command is 300 dpi; however, 600/1200 dpi can be selected using the FRPO B8 command. See Section 6.2. of the Technical Reference manual - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 121
File !R! RES; DAM; UNIT C; FSET 1p08V0s0b5T; MCRO PATTERN; FPAT %1, %2, %3, %4, %5, %6, %7, %8; BOX 5, 1; BLK 5, 1; MRP 0, 1.55; TEXT 'FPAT %1, %2, %3, %4, %5, %6, %7, %8;', L; ENDM; MAP 2, 2; SCP; CALL PATTERN, 3, 3, 0, 0, 0, 0, 0, 0; CALL PATTERN, 255, 0, 0, 0, 0, 0, 0, 0; CALL PATTERN, 1, 1, 1, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 122
printing parameters stored in permanent memory. Each parameter is identified by a code consisting of a letter and a numeral, such as P1. Details parameters and their values are given in Chapter 6 of the Technical Reference manual. The FRPO command should be used only when it is necessary to change - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 123
Printout Related Command FRPO INIT FRPO 113 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 124
dependent parameters for the current interface as well as all non-interface dependent parameters. For a list of the factory default values, see Chapter 6 of the Technical Reference manual. The FRPO INIT command causes a page break. To activate the changes made with the FRPO INIT command, turn the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 125
FSET FSET - change current Font SETting by characteristic Format FSET spacing-pitch-height-style-weight-typeface; Parameters spacing: fixed or proportional spacing, followed by a terminator P: 0 = fixed font 1 = proportional font pitch: pitch in cpi, from 0.44 to 99.99 cpi (ignored in a - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 126
at the end of this section demonstrates this function. Font selection is made based on the characteristics of the font, the font's location in the printer, and the font's orientation. In the list below, the characteristics of font are listed in order of priority, from highest to lowest: Symbol set - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 127
All matches are next examined based on spacing. When the printer has reduced the matches to one font, it selects that font. Bitmap fonts have priority over scalable fonts. FSET enables the user to select a general class of font first, then specify characteristics (e.g. - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 128
PRESCRIBE Command Reference File !R! UNIT P; SFNT 'Swiss742SWC-Roman', 10; SLS 12; EXIT; First, this line is printed in a 10 point Swiss742SWC-Roman font. !R! FSET 14V; SLS 16; EXIT, E; Let's see if the height parameter is changed to 14 points by FSET 14V;. !R! FSET 1s3B; EXIT,E; Now this line - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 129
current font is changed by a FONT, ALTF, or RPF command, the printer automatically changes the designated attributes to the values of the new font. The default value of the FTMD command depends on the emulation mode. The printer does not automatically change any attributes not designated by the FTMD - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 130
Yes Yes Portrait or landscape Yes Yes Yes Yes Yes Default Font Modes Emulation mode 0 (Line Printer) 1 (IBM X-24E) or 2 (Diablo 630) 5 BOX .5, -.5; MRP 1, 0; FONT 37; TEXT 'Font 37, correctly spaced at 10 cpi', N; BOX .5, -.5; MRP 1, 0; FONT 52; TEXT 'Font 52, proportionally spaced', N; BOX - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 131
Printout FTMD 121 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 132
300 dpi resolution, and 1/600 inch in the 600 dpi resolution, and 1/1200 inch in the 1200 dpi resolution. For printer models that support 600/1200 dpi resolution printing, the default resolution generated by the GPAT command is 300 dpi; however, 600/1200 dpi can be selected using the FRPO B8 command - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 133
GPAT Printout Related Commands FPAT, PAT 123 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 134
= represents gray in K (black, default) 1 = represents gray in CMY the corresponding area can be represented by using either the same quantity of toner or only K toner for each of CMY. (If C = M = Y, the so on.) The graying process defaults to representation using K toner alone. However, a toggle - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 135
GRRD GRRD - GRaphic data ReaD COLOR Format GRRD format, width, height; ;ENDG; Parameters format: image format: B = Bitmap J = JPEG T = TIFF width: number from 0 to 65535 height: number from 0 to 65535 image: file name based on a specified format Function The GRRD command allows the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 136
PRESCRIBE Command Reference c:¥> echo !R! STR 300; MZP 1,1; GRRD J,0,0; > lpt1 c:¥> copy /b fluit.jpg lpt1 c:¥> echo ;ENDG; PAGE; EXIT; > lpt1 Printout 126 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 137
for hue adjustment: 0 = all colors 1 = R 2 = Y 3 = G 4 = C 5 = B 6 = M angle: angle of hue rotation in degrees: color = 0, - 180 to 180 (default = 0) color = 1 - 6, -10 to 10 (default = 0) type: object type Function The HUE command shifts all the pixels around the 'color wheel' to a different - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 138
G C B M If this command is issued to rotate a particular hue when all hues are rotated, the hues are controlled after they are reset to their default state. The HUE command is enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 139
. Depending on the current emulation, the printer selects one of the symbol sets of the emulated printer appropriate for the country as requested by the country-code value. For example, when the printer is set in the default emulation mode 6 (HP LaserJet), country code 0 (US ASCII) selects the ISO - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 140
to the code-set parameter specified, the printer selects a symbol set available to the current emulation. The default country-code value appears foreign characters not found in a current symbol set. (Default is US ASCII). It does not fully support all of the HP LaserJet symbol sets. To use one - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 141
INTL File !R! CMNT This file will not print correctly in the IBM; CMNT emulation (mode 1); RES; INTL 2, 2; SLM 1; STM 2; SFNT "Helvetica", 14; EXIT; Diese [pfel sind eine ]berraschung! !R! PAGE; EXIT; Printout 131 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 142
to 255 = tray ID (specified by JOBS) Character string = job ID or alias of virtual mailbox, must be enclosed by single or double quotation marks password: four-digit number specified by VMPW to secure the mailbox Function The JOBD command deletes the jobs stored in the hard disk. This command may - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 143
; To delete all temporary and permanent jobs in the hard disk: !R! JOBD; EXIT; To delete the jobs stacked in virtual mailbox number 3, which has the password of 9999: !R! JOBD 8, 3, 9999; EXIT; 133 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 144
over the mailbox number for virtual mailboxes which contain jobs. A Full!! is displayed next to the job size entry for virtual mailboxes containing jobs which caused an error during data is written to the mailbox. An error log indicating failure is also printed when jobs within such a mailbox - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 145
File To print a permanent job list: !R! JOBL 2; EXIT; JOBL 135 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 146
id (mode 8): mailbox ID from 1 to 255, or alias password (mode 8 only): password for the mailbox Function The JOBO command retrieves a temporary or permanent is corrupted in hard disk, an error is messaged on the operator panel display as follows: Hard Disk Error 99 98 Meaning The job does not - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 147
, if set previously by VMPW, is valid for all virtual mailboxes for which a password is set. An error will be displayed on the operator panel if no password or an incorrect password is specified. An error will result also if no virtual mailbox corresponds to the alias given or if no job is present - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 148
20 = staples the number of specified sheets. 0 = off 1 = center stitch and stapling 0 = off 1 = main position 2 = alternate position 0 = off 1 = blank separator 2 = duplicated separator number representing the paper source (tray) 0 = off 1 = on 138 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 149
JOBP printoption 13 Function Booklet Parameter 0 = off 1 = longitudinal feeding, left binding 2 = longitudinal feeding, right binding 3 = lateral feeding, left binding 4 = lateral feeding, right binding Effective to: Function The JOBP command implements printing a print job which was prologued - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 150
save-mode, copy, barcode, barcode-position[, share, 'job-name', 'user-name', 'time']; Parameters save-mode: save mode: 0 = electronic Must be 0 job-name: job name, character string up to 80 bytes user-name: user name, character string up to 80 bytes time: time stamp, character string up - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 151
barcode scanner manual.)' and information regarding the job which was thrown away is displayed in the error log. If JOBS-JOBT pairs are nested or if they are not paired properly, the job defined between the innermost JOBS-JOBT pair will be valid. The command is invalid if any of the job name, user - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 152
printer driver is being used) will be displayed on the message display instead of Processing. To print 25 copies of the job named Project-report1 with user 0, 'Invoice', 'Sales', '01/14/02 16:30:25'; UNIT C; MZP 5, 10; BOX 6, 6; PAGE; TEXT 'November Result'; PAGE; TEXT 'To Mr. Johnson'; PAGE; JOBT; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 153
JOBS !R! JOBS 8, 3, 3, 15, 0, 'Service', 'Repair', '01/14/02 16:30:25'; UNIT C; MZP 5, 10; BOX 6, 6; PAGE; TEXT 'ABCDE'; PAGE; TEXT 'Domestic'; PAGE; JOBT; EXIT; 143 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 154
PRESCRIBE Command Reference JOBT - JOB Terminate Format JOBT; Parameter None Function The JOBT command terminates defining a job which is started by JOBS. The JOBT command is used in combination with JOBS to constitute a job definition. The printing system prints the job in the number of copies - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 155
command such as RES, FRPO and SEM which results in a reset of the printer. When JOG is issued with a job defined by JOBS and JOBT, jogging affects copies of the job defined between JOBS and JOBT (job name: My Trial, user name: Halle Berry, date: January 12, 2002) with the electronic sorting function - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 156
the function that starts the user program (Only in the case of "PRE") Up to 31 characters Function The LAPI command downloads the API program. As the specified command name has already been stored, the sending data will be invalid. Data downloaded with the LAPI command will be deleted (invalid) - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 157
-number: font number (integer from 1000 to 65535). Same for all characters in the font. Must not duplicate any resident bitmap font number. code: ASCII code of the character (0 to 255) height: height of the character bitmap, in dots (integer from 0 to 3999) width: width of the character bitmap - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 158
such as the one shown below, which is defined as the '+' symbol (character code 43) of font 1000. Details and another example appear in Chapter 4 of the Technical Reference manual. The resolution is valid only on a 600/1200 dpi printer model. File !R! LDFC 1000, 43, 39, 29, 1216, 0, 1216, 608 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 159
, height, width, y-offset, x-offset, cell-width; bit-map; Parameters font-number: font number (integer from 1000 to 65535) code: ASCII code of the character code (0 to 255 for European; 0 to 65533 for Japanese) or in hexadecimal notation ($xxxx) height: height of the character bitmap, in dots - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 160
downloaded font header already defined using LDFN F. Note that each character code defined must match the font number, symbol set (1- or 2-byte code), and other information of the font header already created. The bitmap data transferred at the end of this command is transferred under Kyocera error - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 161
must be enclosed in either single or double quotation marks. symbol-set: symbol set: numeric value = 1-byte code symbol set (1 to 65535 [619: Shift JIS code]) J = 2-byte JIS code spacing: spacing: 0 = fixed spacing 1 = proportional spacing width: font width (in dots set by resolution): 3 to 3000 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 162
codes from 32 to 127 1 = character codes from 32 to 127 and from 160 to 255 2 = character codes from 0 to 255 Function The LDFN F command creates a font header for downloading a font to the printer byte code) emulation Japanese character (2-byte code) emulation (linked using ASFN) A command error - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 163
Since there are two font headers for Japanese TrueType fonts, the printer automatically creates a font number increased by 1. name: font name: data symbol-set: font symbol set value: 1 to 65535 (619 = Shift JIS code) style: font style: 0 to 32767 stroke: stroke weight: -127 to +127 type - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 164
part of the font data length. The maximum number of fonts that can be downloaded is up to the memory available or 256 fonts (512 when format is are outside the given range. This command is ignored if even one parameter error occurs. Although symbol-set, style, stroke and type-face may be omitted, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 165
gamma control mode, the color bars below represent the lightness gamma variation using hue R as an example. The top color bar represents the default lightness variation (γ = 1.0) with its median indicated by the symbol. The left side represents the lower lightness range and the right side the higher - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 166
PRESCRIBE Command Reference Default contrast Contrast set to high Contrast set to low Varying the darkness contrast allows the difference between the . This mode is not held permanently in the printing system. For this reason, saturation is reset to its default state when the power is turned on. 156 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 167
margin. The MAP command is ignored in path mode graphics. File !R! RES; UNIT C; STM 2; SLM 2; SFNT 'Helvetica-Nr', 9; MAP 0, 0; BOX 40, 40; SPD .2; MAP 0, 1.4; TEXT '< = = = Margins'; MAP 0, 0; CIR .1; TEXT, L; TEXT ' MAP 0, 0;'; MAP 4, 0; CIR .1; TEXT, L; TEXT ' MAP 4, 0;'; MAP 0, 2; CIR .1; TEXT - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 168
PRESCRIBE Command Reference Printout Related Commands MRP, MZP, MRPA 158 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 169
mode of color matching. Color matching mode is changed according to the various conditions of emulation, paper type, and print quality. In monochrome mode, color matching is defaulted to 0 (none). Mode 0 does not perform color matching. Mode 1 automatically selects color correction mode depending on - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 170
name: character string starting with a letter dummy-sign: any character (default: % preceded by a space) comment: any character string Function ) command, or by switching power off. See the Technical Reference manual for information on the limitations about the usage of macros. The PCL5E command - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 171
, and macros stored in the EPROM. Memory card and EPROM based PCL macros cannot be deleted. Downloaded PCL macros, available for all FS-series printers, may be removed using the PCL reset or delete commands: &f6X or &f8X. Downloaded macros may also be sent to specific host buffers of the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 172
15 = Second side 16 = Thick 21 = Custom 1 22 = Custom 2 23 = Custom 3 24 = Custom 4 25 = Custom 5 26 = Custom 6 27 = Custom 7 28 = Custom 8 paper-weight 0 = Normal 1 = Heavy (Thick) 2 = Light (Thin) 3 = Extra thick 10 = Light 11 = Normal 1 12 = Normal 2 13 = Normal 3 14 = Heavy 1 15 = Heavy 2 16 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 173
all the parameter are omitted (MDAT;), all the attributes for the all media types are reset to the default. File To set the transparency paper type to the thick paper weight and the high fuser temperature mode, disabling the duplex printing, command: !R! MDAT 2, 1, 0, 1; EXIT; Related Command MTYP - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 174
's Manual. Note File This command is irrelevant to certain combination of photocopier models and option finisher models. To enable the multiple user mode (FRPO S0, 1;), to create three groups, to select the second group, and to deliver outputs in the fourth tray in the (second) group, send the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 175
, and the number of Quick Copy jobs in the hard disk. Files To set the maximum capacity for the permanent jobs to 600 MB: !R! MPSS 'CODE', 'PERMLIMITSIZE', 600; EXIT; To set the maximum capacity of the virtual mailbox to 800 MB: !R! MPSS 'VMB', 'VMBLIMITSIZE', 800; EXIT; To set the maximum number - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 176
the MP tray is empty. Function When the MP tray is configured as the default paper source, the MPTE command enables or disables the paper-empty message which is shown when the MP tray becomes empty. Mode 1 (default) enables the paper-empty message to display when the MP tray is empty. When Mode is - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 177
MRP MRP - Move to Relative Position Format MRP x-coordinate, y-coordinate; Parameters x-coordinate/y-coordinate: coordinates as measured from the current cursor position Function The MRP command moves the cursor from its current position to a specified relative position, measured in the units - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 178
PRESCRIBE Command Reference Printout Related Commands MAP, MZP, MRPA 168 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 179
MRPA MRPA - Move to Relative Position specified by Angle Format MRPA distance, angle; Parameters distance: distance to move angle: angle in degree, measured clockwise from the vertical Function The MRPA command moves the cursor from its current position across a specified distance using a - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 180
PRESCRIBE Command Reference Printout Related Commands MAP, MRP, MZP 170 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 181
only when the option sorter is installed with the printing system. It instructs the printing system to deliver printed pages in the mailbox mode. it also becomes full. When the bulk tray becomes full, the printing system pauses and displays a message which urges the user to remove paper. By removing - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 182
MTYP command automatically selects the paper source (tray or cassette) paper source which has the matching media type. To assign a paper type to the paper paper source) command section in this manual. To ensure that the paper paper in the cassette one (topmost cassette), first assign the plain paper - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 183
MP tray size to A4 and the MP tray type to Labels (See the user's manual for details.) !R! RES; PSRC 100; CMNT Sets the printer to automatic casette mode; CMNT Depending on the current media type; SPSZ 8; MTYP 4; CMNT Paper size = A4, media type = label; RES; EXIT; Related Commands PSRC, SPSZ 173 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 184
relative to the top and left edge limits of the paper, measured in the units designated by the UNIT command. to Zero-relative Position) command. File !R! RES; UNIT C; STM 2; SLM 2; SFNT 'Helvetica-Nr'; MZP 0, 0; BOX 40, 40; SPD .2; MZP 0, 4; TEXT '< = = = Edge limits'; MZP 0, 0; CIR .1; TEXT, L; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 185
MZP Printout Related Commands MAP, MRP, MRPA 175 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 186
with any painting operator that paints the path or draws a line along it (STRK, FILL). For a full description of path, refer to Chapter 1 of the Technical Reference manual. File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 1, -2, 3, 0, -1, 2, -3, 0; STRK; CMNT Stroking the path; NEWP; PMZP 10, 5; PDRP - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 187
OTRY OTRY - select paper Output TRaY Format OTAY tray; Parameter tray: 1 = printing system's face- command. The default value is 1: the printing system's face-down tray. If an optional device such as a stacker, a document finisher, or a sorter is installed, the tray value 2 instructs the printing - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 188
delivered face-down as usual, page 1 first. !R! PAGE; EXIT; PAGE 2 PAGE 2 next, and so on, stacking in the correct order. !R! PAGE; EXIT; PAGE 3 But on printers with two paper trays this file will be delivered to the face-up tray with the pages in reverse order, page 3 on top. !R! PAGE; EXIT; 178 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 189
PAGE PAGE - start new PAGE Format PAGE; Parameter None Function The PAGE command causes a page break without resetting the printer. Subsequent data will be printed on a new page with no changes made to page formatting parameters such as spacing, margins, font selection. If there is - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 190
PRESCRIBE Command Reference PANT - create PANTone color palette COLOR Format PANT color-number or 'color-name'; Parameters color-number: Pantone color number, integer from 100 to 5999 color-name: Pantone color name Function The PANT command can be used to specify the PANTONE uncoated color by - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 191
4 Warm Gray 4 Warm Gray 8 Cool Gray 4 Cool Gray 8 The PANT command may not work with certain printer models and versions. Set the print quality to Quick mode when this command is used with model FS-5800C. PANTONE colors cannot be used by the PANT command in KPDL emulations. !R! PANT 'Cool Gray - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 192
PRESCRIBE Command Reference PARC - in Path, draw ARC Format PARC x-coordinate, y-coordinate, radius, start-angle, end-angle; Parameters x-coordinate, y-coordinate: coordinates of the center of arc, measured from the left and top edge limits radius: radius of arc start-angle: starting angle, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 193
PARC Printout 183 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 194
between 1 through 60 if a resident pattern is selected. A full list of the printer's resident patterns appear on the following page. Pattern numbers 100 patterns are defined, the printer selects the No. 1 (solid black) resident pattern. Variable resolution support is valid for 600 dpi and 1200 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 195
PAT Resident Fill Patterns (300 dpi) 185 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 196
PRESCRIBE Command Reference PCRP - in Path, Curve to Relative Position Format PCRP x1, y1, x2, y2, x3, y3; Parameters x1, y1: coordinates of the first control point as measured from the current cursor position x2, y2: coordinates of the second control point as measured from the current - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 197
File !R! RES; UNIT C; NEWP; SPD .1; PMZP 3, 3; PCRP 4, 2, 5, 1.5, 6, 1.8; STRK; PAGE; EXIT; Printout Current positon (5, 1.5) (4, 2) (6, 1.8) File !R! RES; UNIT C; NEWP; SPD .1; PMZP 3, 3; PCRP 5.5, 1.5, 1.5, 5.5, 7, 7; STRK; PAGE; EXIT; Printout Current positon (5.5, 1.5) PCRP (1.5, 5.5) - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 198
x2, y2: coordinates of second control point as measured from the left and top edge limits of paper x3, y3: coordinates of end point as measured from the left and top edge limits of paper Function The PCZP command adds a Bézier curve segment to the path, starting from the current cursor position - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 199
File !R! RES; UNIT C; PMZP 3, 6; PCZP 11, 3, 2, 2, 9, 6; STRK; PAGE; EXIT; Printout (2, 2) PCZP (11, 3) (9, 6) Current position (3, 6) 189 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 200
PRESCRIBE Command Reference PDIR - set Print DIRection Format PDIR angle; Parameter angle: angle in degrees; in 90° increments in a counterclockwise direction 0 = portrait 90 = landscape 180 = reverse portrait 270 = reverse landscape Function The PDIR command rotates the coordinates of the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 201
Portrait (PDIR 0;) Landscape (PDIR 90;) PDIR Reverse Landscape (PDIR 270;) Reverse Portrait (PDIR 180;) File !R! RES; UNIT P; SFNT 'Helvetica', 8; UNIT C; MZP 10, 12; SPD .144; CIR .075; PDIR 270; TEXT ' ENDLESS VARIETY AND VERSATILITY'; PDIR 180; TEXT ' ENDLESS VARIETY AND VERSATILITY'; PDIR - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 202
PRESCRIBE Command Reference Printout 192 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 203
outside the current page. The thickness of the line is designated by the SPD command. Multiple pairs of coordinates may be specified. The printer then draws a connected series of line segments, proceeding from one point to the next. For example, PDRP 1, 2, 3, 4; is equivalent to PDRP 1, 2; PDRP - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 204
PRESCRIBE Command Reference Printout Related Command PDZP 194 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 205
PDZP PDZP - in Path, Draw to Zero-relative Position Format PDZP x-coordinate, y-coordinate; Parameters x-coordinate, y-coordinate: coordinates as measured from the left and top edge limits of the current page Function The PDZP command adds a line to the current path from the current cursor - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 206
PRESCRIBE Command Reference Printout Related Command PDRP 196 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 207
FILL is required. A complete ellipse path will be defined if the parameters in brackets are omitted. Executing this command will close current sub-paths. An error will result and the command has no effect if the bounding box is specified as a straight line or a point. 197 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 208
) N : C : P : File !R! RES; UNIT C; MZP 0, 0; BOX 2, 3; NEWP; PMZP 0, 0; PELP 2, 3, 2, 0, 0, 0, N; STRK; MZP 5, 5; BOX 2, -3; NEWP; PMZP 5, 5; PELP 2, -3, 2, 0, 0, 0, N; STRK; MZP 10, 5; BOX -2, -3; NEWP; PMZP 10, 5; PELP -2, -3, -2, 0, 0, 0, N; STRK; MZP 15, 0; BOX -2, 3; NEWP; PMZP 15,0; PELP - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 209
fractions.) The sum of the slice sizes should not exceed 9999. The total length of the command must not exceed 255 characters. The printer automatically converts the slice sizes to angles totaling 360 degrees. It draws the first slice starting at the position specified by the second parameter - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 210
PRESCRIBE Command Reference Printout 200 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 211
PMRA PMRA - in Path, Move to Relative position specified by Angle Format PMRA x-coordinate, y-coordinate, distance, angle; Parameters x-coordinate, y-coordinate: coordinates as measured from the left and top edge limits of the page distance: distance specified in increments governed by the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 212
PRESCRIBE Command Reference File !R! RES; UNIT C; SPD 0.2; NEWP; PMRA 10, 19, 5, 45; PARC 10, 19, 5, 45, 135; STRK; PAGE; EXIT; Printout 202 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 213
PMRP PMRP - in Path, Move to Relative Position Format PMRP x-coordinate, y-coordinate; Parameters x-coordinate, y-coordinate: coordinates as measured from the current cursor position Function The PMRP command moves the cursor from its current position to a specified relative position in a path - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 214
PRESCRIBE Command Reference Printout Related Command PMZP 204 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 215
off the current page. File !R! RES; UNIT C; STM 2; SLM 2; SFNT "Helvetica-Nr"; NEWP; PMZP 0, 0; SPD .2; PMZP 0, 4; FONT 13; TEXT '< = = = Paper edge limits'; PMZP 0, 0; PARC 0, 0, .1, 0, 360; PMRP 0, .333; TEXT ' PMZP 0, 0;'; PMZP 4, 0; PARC 4, 0, .1, 0, 360; PMRP 0, .333; TEXT ' PMZP 4, 0;'; PMZP - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 216
PRESCRIBE Command Reference Printout Related Command PMRP 206 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 217
PNCH PNCH - PuNCH Format PNCH[ mode]; Parameter mode: number of punched holes: 1 = 2 (Europe) or 3 (U.S.) 2 = 4 (Europe) or 2 (U.S.) 51 = 2 (Europe) or 3 (U.S.), left 52 = 4 (Europe) or 2 (U.S.), left 61 = 2 (Europe) or 3 (U.S.), right 62 = 4 (Europe) or 2 (U.S.), right 71 = 2 (Europe) or 3 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 218
with the standard punch unit only (e.g. the DF-75), the number of punched holes is uniquely determined according to the country of destination and paper size. Like stapling and other finishing operations, punching is done per one job at a time. Therefore, this command is invalid unless it is used - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 219
Format PRBX width, height, radius; Parameters width: width of round box height: height of round box radius: radius of round box corners Function The PRBX command adds a round box path to the current path. This command close the sub-paths but does not stroke the path by itself. Therefore, STRK - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 220
-Bd", 24; TEXT "CAUTION: HOT SURFACE!"; PAT 5; NEWP; PMZP 1, 4; PRBX 5, 2.4, 0.3; FILL; MZP 1.4, 4.7; SFNT "Helvetica-Nr", 12; TEXT "Barefoot Systems, Inc.", L; TEXT "4203 Charleston Avenue", L; TEXT "P.O. Box 150", L; TEXT "Edinburgh, CA 94039-1057"; PAGE; EXIT; Printout 210 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 221
PRRC PRRC - in Path, at Relative position, draw aRC Format PRRC x-coordinate, y-coordinate, radius, start-angle, end-angle; Parameters x-coordinate/ y-coordinate: coordinates as measured from the current cursor position radius: radius of arc start-angle: starting angle, measured - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 222
PRESCRIBE Command Reference PRRC 1, 1, 180, 0; Negative values are acceptable for angle. For example, an angle of 315 degrees is the same as -45 degrees. File !R! RES; SPD 0.05; MZP 4.5, 5; NEWP; PRRC -1, 0, 1, 90, 270; PRRC 1, -2, 1, 0, 180; PRRC 2, 1, 1, -90, 90; PRRC -1, 2, 1, 180, 0; STRK; PAGE; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 223
file or program, or at the top of a new page. The current paper source will remain selected if the specified cassette is not installed. File !R! RES; SFNT "Helvetica-Nr", 24; PSRC 1; TEXT "This page is fed from the default cassette."; PAGE; PSRC 0; TEXT "This page is fed from the multi-purpose tray - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 224
(3, 4), a different result is obtained depending on each pixel placement mode. Grid intersection is default to HP PCL; and grid centered mode is used by Microsoft Windows. This command is ignored when used with DAP, DRP, DRPA, DZP, BOX, BLK, CIR, ARC, or PIE. This command has no effect for text or - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 225
in the PRESCRIBE mode, the printer ignores the mistaken !R! and whatever follows, up to the next semicolon. File !R! SFNT 'Helvetica', 14; EXIT; Following these five lines, the printer enters PRESCRIBE mode to execute commands. !R! UNIT I; BOX 2, 2; BOX 1, 1, E; CIR 1; BOX 1, 1; PAGE; EXIT; 215 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 226
PRESCRIBE Command Reference Printout Related Commands EXIT, SCRC 216 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 227
Format RCLT; Parameter None Function The RCLT command instructs the printing system to stack the sets on the RCLT command is available when printing using A4, B5 and letter size paper. During printing, the same size paper must be loaded into two separate cassettes. For example, Portrait (A4 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 228
PRESCRIBE Command Reference RDMP - Received-data DuMP Format RDMP; Parameter None Function The RDMP command causes all subsequent data to be printed in hexadecimal form (two hexadecimal digits per character) until an ENDD (END Dump) command is received, or until the printing system runs out of data - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 229
Sample RDMP 219 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 230
printer environment in the same manner as the KC-GL DF instruction. Refer to section HP 7550A Emulation [KC-GL] (Mode 8) of the Technical Reference manual per page Cassette Cassette 1 (main cassette) (R4)a ← Paper tray Face-down (R0)a ← ← Paper size Cassette size (R2)a ← ← Top margin 1/2 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 231
FSET, or V3 (scalable SFNT font)a Alternate font assignment None See Emulation of ← the Technical Reference manual. SETF Country code 0 (U6)† ← ← INTL Symbol set Roman-8 (U6/7) See Emulation of US ASCII (U7 only when the FRPO C6 (panel keep) is active with a parameter of 1 (default). 221 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 232
, the image data currently remaining is forcibly output on paper. This does not affect the current unit of measure, been downloaded into RAM to be purged. The printing system's resolution setting enabled by this command is reset to default (FRPO printer, IBM ProPrinter, Diablo 630, EPSON LQ850. 222 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 233
individually corrects the gamma for each color. The color bars below represent color balance variations for each of RGB. The top bar represents the default saturation variation. The output result for an input value is maintained in linear form. The middle color bar is an example showing an increase - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 234
and all monitor simulation modes. If ink simulation is set to other than none, this command is disabled. The RES command resets saturation to its default state. This mode is not held in the printing system. For this reason, color balance is reset to its - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 235
coordinate (0, 0) for the physical paper feed direction, in current unit. #Z), the offset values are cleared to zero only by a software reset (E). In other words, the offset is only cleared error will result and the command has no effect if a command format other than the above is used. An error - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 236
PRESCRIBE Command Reference RPCS - Return to Previous Code Set Format RPCS; Parameter None Function The RPCS command resumes use of a code set saved by a previous SCCS (save current code set) command. The RPCS commands return to the code sets in reverse order in which they were nested. File See SCCS - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 237
RPF RPF - Return to Previous Font Format RPF; Parameter None Function The RPF command resumes use of a font saved by a previous SCF (save current font) command. The RPF commands return to the fonts in the reverse order in which they were saved. SCF and RPF are particularly useful in macros. File !R! - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 238
PRESCRIBE Command Reference RPG - Return to Previous Graphics state Format RPG; Parameter None Function The RPG command restores the graphics state most recently saved by a SCG (Save Current Graphics) command. The following items of graphics state revert to the state saved previously. • Path and - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 239
RPG Printout Related Command SCG 229 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 240
PRESCRIBE Command Reference RPP - Return to Previous Position Format RPP; Parameter None Function The RPP command moves the cursor to a position saved by a previous SCP (save current position) command. If the RPP command is executed by mistake when no previous position has been saved, the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 241
RPP Printout Related Command SCP 231 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 242
PRESCRIBE Command Reference RPPL - Return to Previous PaLette COLOR Format RPPL; Parameter None Function The RPPL command restores the color palette most recently saved by a SCPL (save current palette) command. A color palette restored using the RPPL command immediately becomes active. If the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 243
RPU RPU - Return to Previous Unit Format RPU; Parameter None Function The RPU command brings the unit of measurement (inches, centimeters, points, or dots; as specified by the UNIT command) back to the unit saved by the SCU (save current unit) command. File/Printout See SCU on page 283. Related - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 244
PRESCRIBE Command Reference RTTX - RoTate TeXt Format RTTX angle, 'string'[, U-option]; Parameters angle: angle of rotation in degrees string: character string U-option: Underline text Function Taking the normal output angle for text as zero, the RTTX command rotates a character string - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 245
RTTX Printout 235 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 246
margins. The length of the string is unlimited, except that the command as a whole may not be longer than 255 characters. Carriage-return and linefeed codes in the string are ignored. The RTXT command can be used both in the standard mode and path mode graphics. 236 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 247
File !R! RES; UNIT P; SFNT 'TimesNewRoman'; UNIT I; MCRO PF; MRP .15, 0; BOX .1, -.1; MRP .5, 0; BOX .1, -.1; MRP -.65, 0; ENDM; MAP 3, 3; TEXT 'Pass Fail', L, U; CALL PF; RTXT 'Unit test', L; CALL PF; RTXT 'Integration test', L; PAGE; EXIT; Printout RTXT 237 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 248
starts at the current cursor position. The SRO (Set Raster Options) command specifies the orientation of the raster image in either physical (default) or logical page direction. If the compression-mode value is zero [or omitted], the printing system simply transfers raster data in an uncompressed - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 249
RVCL RVCL - ReceiVe CoLor raster data COLOR Format RVCL [compression-mode,] length, data; Parameters compression-mode: 0 = uncompressed (Default) 1 = run-length encoded 2 = TIFF (Tagged Image File Format) [rev. 4.0] length: bytes of raster data data: binary raster data, 0H to FFH Function - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 250
PRESCRIBE Command Reference RVRD - ReceiVe Raster Data Format RVRD; number of data, data, ... ; Function The RVRD command declares the start of raster data. Raster data represents dot lines encoded as numeric values as shown below. Each dot line is divided into 8-dot segments. Each segment is - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 251
which follows. The subsequent data can be obtained by following the same procedure as explained in Defining Fill Patterns in Chapter 2 of the Technical Reference manual. 241 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 252
2 = Printable data 16 = Macro data 112 = File data 128 = API data (downloadable program) partition-name: Name of partition from which data is deleted Function The RWER D (by the RWER I command). ( See page 244.) A command error results and the command has no effect if parameters other than the above - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 253
disk is physically formatted when it is specified. This command has no effect if the media has been write-protected using KPDL or PJL. A command error results and the command has no effect if parameters other than the above are used. This command causes a page break and prints a format information - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 254
enabled (RWER I, E;), the printing system prints partition lists whenever data are written to external media. The setting made with this command returns to default when the power is turned off. A command error results and the command has no effect if parameters other than the above are used. 244 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 255
omitting parameter medium. Disk capacity, font cache capacity and data type are listed, with login file names for file data output in separate columns. A command error results and the command has no effect if parameters other than the above are used. 245 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 256
-type, 'partition-name'; Parameters medium: 0 = hard disk or RAM disk A = memory card E = EPROM data-type: 2 = Printable data 128 = API data (downloadable program) partition-name: Name of partition from which data is read, a maximum of 15 printable ASCII characters Function The RWER R command - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 257
or double quotation marks. length: font data length (number of bytes sent as binary data) value: font symbol set value (1 to 65535, 619: Shift JIS code) style: font style (0 to 32767) weight: stroke weight (-127 to +127) type-face: type face (0 to 32767) 247 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 258
The RWER S command allows outline fonts (in TrueType format) to be downloaded to the printing system and to be stored on the specified media as appends (P) for proportional fonts and (F) for fixed pitch fonts. A command error will result and the command has no effect if any of the parameters are - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 259
. This terminator is used when storing binary data to external media. See the RWER S command page (page 247) for example. WRED is set as the default terminator if parameter terminator is omitted. A command error results and the command has no effect if parameters other than the above are used. 249 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 260
= Macro data 112 = File data 128 = API data (downloadable program) partition-name: Name of partition to which data is written as a warning when this happens. A command error results and the command has no effect if The following example demonstrates how to send data from the computer to a memory - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 261
2, 'DATA123'; >PRN The message display will change from Ready to Processing, and then to Waiting. The printing system is now ready to receive data, so send the file from the computer to the printing system. 3. To do this, enter the following at the DOS prompt: C:\>COPY DATA123.DOC PRN 4. The message - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 262
PRESCRIBE Command Reference RWRF D - [Read/Write Resource File] Delete data on external device Format RWRF D, medium, data-type, "file-name"; Parameters medium: 0 = hard disk A = memory card data-type: "API" API program "FNT" Font data "MCR" Macro data "PRN" Printable data file-name: ASCII text - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 263
RWRF F RWRF F - [Read/Write Resource File] Format external device Format RWRF F, medium; Parameters medium: 0 = hard disk A = memory card Function The RWRF F command physically and logically formats an external device such as the hard disk. This command has no effect if the target device has - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 264
PRESCRIBE Command Reference RWRF L - [Read/Write Resource File] print resource file List Format RWRF L[, 'medium']; Parameters medium: 0 = hard disk A = memory card Prints a resource file list for all devices if omitted. Function The RWRF L command prints a resource file list registered in an - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 265
RWRF P RWRF P - [Read/Write Resource File] set hidden file Format RWRF P, medium, data-type, "file-name"; Parameters medium: 0 = hard disk A = memory card data-type: "API" API program "FNT" Font data "MCR" Macro data file-name: ASCII text string up to 15 bytes. Function The RWRF P command sets - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 266
PRESCRIBE Command Reference RWRF R - [Read/Write Resource File] Read Format RWER R, medium, "PRN", 'partition-name'; Parameters medium: 0 = hard disk A = memory card partition-name: Name of partition from which data is read, a maximum of 15 printable ASCII characters Function The RWRF R command - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 267
set Terminate string Format RWRF T[, 'terminator']; Parameters terminator: ASCII text string up to 4 bytes Set to default "WRED" if omitted. Function The RWRF T command changes a terminator (default: WRED). The terminator that was changed with this command is also available for the LAPI command - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 268
PRESCRIBE Command Reference RWRF W - [Read/Write Resource File] Write data to external device (API program) Format RWRF W, medium, "API", "program-type", prescribe-command-name, APIprogram-start-function-name, "file-name"; Parameters medium: 0 = hard disk A = memory card program-type: "PRE" - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 269
: ASCII text string up to 31 bytes Up to 28 bytes for font type 2 font-data-length: Number of bytes in font data to be downloaded symbol-set-value: 1 to 65535 (619 = Shift JIS code) font-style: 0 to 32767 stroke-weight: -127 to +127 typeface: 0 to 32767 259 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 270
exactly select a font. The length of the font data to be written must match the specified one. Failure to do so will result in an error, and disables you to write data. Specify WRED; command following . "WRED;" (five bytes) are not included in the font data length. To delete - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 271
RWRF W RWRF W - [Read/Write Resource File] Write data to external device (macro) Format RWRF W, medium, "MCR", macro-type, "macro-ID or macro-name", "filename"; Parameters medium: 0 = hard disk A = memory card macro-type: "PRE" prescribe macro "PCL" PCL macro macro-ID or macro-name: macro-ID - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 272
PRESCRIBE Command Reference RWRF W - [Read/Write Resource File] Write data to external device (printable data) Format RWRF W, medium, "PRN", "file name"; Parameters medium: 0 = hard disk A = memory card file-name: ASCII text string up to 15 bytes Automatically set by the system if omitted. - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 273
on the specified parameter. The color bars below show saturation variations using hue "R" as an example. The top color bar represents the default saturation variation. The symbol indicates the median. The left side represents the lower saturation range and the right side the higher saturation range - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 274
bottom margin Function The SBM command sets the bottom margin, as measured from the top edge limit of the paper in the units designated by the UNIT command. If an attempt is made to print below the bottom margin, the characters will be printed on - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 275
SBM Printout 265 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 276
2 = butt caps 3 = round caps Function The SCAP command determines the shape of line ends (or a line cap) in a path where they are finally stroked. The default caps is butt caps (2). Square caps have square ends which extend one-half of a line width beyond the endpoints of the line. Butt caps are - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 277
SCAP Printout 267 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 278
SCCS; Parameter None Function The SCCS command instructs the printing system to remember the code set of the current font. This command may be used in conjunction with a SCF (save current font) command to prevent the font from losing the current code set after a command operation has been made - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 279
SCCS Printout Related Commands RPCS, RPF, SCF 269 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 280
to eight font numbers can be saved in the printing system's memory by SCF commands (using a separate SCF command for each). The SCF command only instructs the printing system to remember the font. It does not move actual fonts in or out of memory. File !R! RES; SLM 1; STM 2; SFNT 'TimesNewRoman - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 281
SCF Printout Related Command RPF 271 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 282
no strokable path. The printing system holds as much graphics state information as the user memory area can accommodate; however, graphics state information larger than the memory area can cause a memory error. File !R! RES; UNIT C; NEWP; PMZP 5, 5; SFNT 'Helvetica-Bd', 72; CPTH 'Mary'; SCG; STRK - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 283
SCG Printout Related Commands FILL, RPG 273 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 284
PRESCRIBE Command Reference SCOL - Select COLor COLOR Format SCOL number; Parameter number: number from 0 to 255 (Default is 0.) Function The SCOL command selects a color from the currently active palette. If no color is assigned to the specified number, this command is ignored. - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 285
SCP SCP - Save Current Position Format SCP; Parameter None Function The SCP command instructs the printing system to remember the current cursor position, so that it can be retrieved later using the RPP (return to previous position) command. Up - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 286
PRESCRIBE Command Reference SCPI - Set Characters Per Inch Format SCPI number; Parameter number: number of characters per inch Function The SCPI command sets the number of characters per inch (even if the UNIT command designates a non-inch unit). When a proportionally-spaced font is used and - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 287
SCPI Printout Related Command SCS 277 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 288
PRESCRIBE Command Reference SCPL - Save Current PaLette COLOR Format SCPL; Parameter None Function The SCPL command saves the currently active palette, so that it can be retrieved later using the RPPL (return to previous palette) command. Palettes can be saved as many as there is enough memory - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 289
command recognition character, any character from ASCII code 33 (!) to ASCII code 126 (~) except the apostrophe ('), quotation mark !R! RES; UNIT C; GPAT .7; BLK 1, 1; BOX 1, 1, E; GPAT .5; BLK 1.3, 1.3; BOX 1.3, 1.3, E; GPAT .3; BLK 1.6, 1.6; BOX 1.6, 1.6, E; CMNT Now list the above commands; - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 290
PRESCRIBE Command Reference Printout 280 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 291
The character spacing can be set using either the SCS or the SCPI command. File !R! RES; SLM 1; STM 2; EXIT; This line has the default spacing. !R! UNIT C; SCS .3; EXIT; This line has a slightly wider spacing. !R! SFNT 'TimesNewRoman', 10; SCS .2; EXIT; This is a proportional font printed with fixed - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 292
Format SCSZ width, height, unit; Parameters width: width of custom paper size height: height of custom paper size unit: M = millimeters I = inches Function The SCSZ command sets the paper size when the user-defined size paper is used in the universal cassette. This command defines the width - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 293
SCU SCU - Save Current Unit Format SCU; Parameter None Function The SCU command instructs the printing system to save the current unit of measurement. Saving the current unit can prove useful when a macro containing a UNIT command changes the unit - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 294
PRESCRIBE Command Reference Printout Related commands SCF, SCP, UNIT 284 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 295
with a space, 0 must be specified for the first dash value (dash1). To end the pattern with a dash, the last space value may be omitted. The user-defined dash patterns are valid until another SDP command changes the current definition or until the printing system is switched off. 285 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 296
PRESCRIBE Command Reference File !R! RES; UNIT P; SDP 11, 2, 2, 5, 5; NEWP; UNIT C; SPD .2; PMRA 10, 10, 3, 0; DPAT 11; PARC 10, 10, 3, 0, 360; STRK; PAGE; EXIT; Printout Related Command DPAT 286 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 297
SEM SEM - Set Emulation Mode Format SEM mode; Parameter mode: 0 = Line Printer 1 = IBM Proprinter X-24E 2 = Diablo 630 5 = Epson LQ-850 system loses the mode set by the SEM command. Upon power up, it retains the default emulation, which is set by the P1 parameter of the FRPO command. If you - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 298
the SFNT (set font) command page. In some emulation modes, default assignments are given to low alternate numbers so that SETF commands can be embedded for some word processing software. See Emulation of the Technical Reference manual. File !R! RES; SFNT 'Helvetica', 10, 2000; SFNT 'Helvetica-BdOb - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 299
SETF Printout 289 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 300
PRESCRIBE Command Reference SFA - Set bitmap Font Attributes Format SFA hmi, vmi, F/P[, rotation, symbol-set, height, U/I, weight, typeface][, font-type]; Executable Parameters hmi: horizontal motion index; in a fixed font, the distance from the center of one character to the center of the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 301
codes. The printing system must be set to the HP transparency mode. See Emulation of the Technical Reference manual.) Function The SFA command specifies the attributes of the current bitmap font. It can be used to change the default is selected by word-processing software in the HP LaserJet - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 302
the font mode is 0 (the default value in the daisywheel emulation mode), be specified. The optional parameters are used to describe downloaded fonts for selection by embedded commands in the HP spaces between words. !R! FONT 1; EXIT,E; The printer remembers the spacing assigned to each font. 292 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 303
SFA Printout 293 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 304
selects the font which matches the type-face parameters. It enables the user to size its height, assign a font number and vary some of the name from the font table in Section 4.2. of the Technical Reference manual. Specify the full name exactly as it appears in the table, including case sensitivity. - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 305
use. If the number matches one already assigned to another font, the printing system ignores the SFNT command. symbol-set uses HP PCL matching code to change the font's symbol set. Unsupported symbol set values, if specified, are ignored. compression squeezes or expands characters in the horizontal - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 306
PRESCRIBE Command Reference This is 10-point Helvetica-Nr, with Roman-8 symbol set, compression is 2, and shear is .3. You can later recall this font by the FONT 3000; command. !R! PAGE; EXIT; Printout 296 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 307
SGPC SGPC - Set kcGl Pen Color COLOR Format SGPC pen-number, color; Parameters pen-number: number from 1 to 8 corresponding to FRPO G1 to G8 parameter color: 0 = Black 1 = Red 2 = Green 3 = Yellow 4 = Blue 5 = Magenta 6 = Cyan 7 = White Function The SGPC command sets the color of a pen 1 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 308
parameter is measured in the unit value specfied by the UNIT command. File !R! RES; SLM 1; STM 2; EXIT; This line has the default spacing. !R! UNIT C; SHMI .3; EXIT; This line has a slightly wider spacing. !R! SFNT 'TimesNewRoman', 10; SHMI .3; EXIT; Proportional fonts are not influenced. !R! PAGE - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 309
) commands can be used for pattern images. With operation modes 1 and 2, the SIMG command takes care of the source image's transparency only. The default operation mode is 1. The white pixels of the source image do not overlay on the destination. For example, you cannot pattern a character. With - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 310
the letter A is patterned only with its opposing quarters. operation mode = 6: Both source and pattern images are opaque, the entire letter A is patterned, and the full source image is overlaid onto the destination. Operation Modes 300 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 311
File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 2.5, 0, 0, 2.5, -5, 0, 0, 2.5, 2.5, 0; PAT 1; SIMG 4; FILL 1; MRP -1, 3.5; PAT 18; FSET 4158T3B0S1P108V; TEXT "A"; FILL 1; PAGE; EXIT; Printout SIMG 301 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 312
SIMP command creates a palette already defined by the system from either a single plane (monochrome) or 3-plane (8-color) RGB palette. The default palette is a monochrome palette. Colors and parameters specifiable by SCOL command for each palette are as follows: palette 1 (single plane) 3 (3-plane - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 313
File !R! RES; UNIT C; SIMP 3; MCRO SIMP; NEWP; SCOL %2; PDRP 2, 0, 0, 2, -2, 0, 0, -2; FILL 1; PMRP .5, .5; ENDM; CALL SIMP,0,0; CALL SIMP,0,1; CALL SIMP,0,2; CALL SIMP,0,3; CALL SIMP,0,4; CALL SIMP,0,5; CALL SIMP,0,6; CALL SIMP,0,7; PAGE; EXIT; Printout SIMP 303 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 314
The SIR command accesses different levels of Kyocera Image Refinement (KIR). The image refinement level remains in effect until the printing system receives a RES command or a different SIR command. The default value is On. Refer to the User's Manual for details about how to obtain the optimum - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 315
mode: 1 = Beveled join 2 = Mitered join 3 = Round join 4 = Notched join Function The SLJN command determines how two connected lines in a path are joined. The default join is beveled (1). Beveled join ends the lines with butt caps (Refer to the SCAP command) and fills the larger angle between the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 316
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; SPD .5; SCAP 3; CMNT Round-capped at the upper-left corner; SLJN 3; CMNT Round-joined at other corners; PMZP 5, 16.5; PDRP 3, 0, 0, 3, -3, 0, 0, -3; STRK; NEWP; SCAP 1; CMNT Square-capped at the upper-left corner; SLJN 2; CMNT Mitered-joined - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 317
SLM distance; Parameter distance: size of left margin Function The SLM command sets the left margin, as measured from the left edge limit of the paper in the unit value designated by the UNIT command. If the margin is moved to the right of the current cursor position, the cursor moves - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 318
PRESCRIBE Command Reference Printout 308 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 319
number of lines per inch (even if the UNIT command designates a non-inch unit). File !R! RES; STM 2; SFNT "Helvetica"; EXIT; These lines have the default spacing of six lines per inch. !R! SLPI 2; EXIT; These lines are spaced at two lines per inch. !R! PAGE; EXIT; Printout Related Command SLS 309 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 320
PRESCRIBE Command Reference SLPP - Set Lines Per Page Format SLPP number; Parameter number: number of lines per page Function The SLPP command sets the bottom margin for an exact number of lines per page based on the current line spacing. As long as you do not change the line spacing or use - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 321
SLPP Printout 311 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 322
SLS sets the number of inches (or other units) per line. File !R! RES; UNIT C; STM 5; SFNT "TimesNewRoman"; EXIT; These lines have the default line spacing of 0.423 cm (6 lpi). !R! SLS .6; EXIT; These lines are spaced at intervals of .6 centimeters. !R! PAGE; EXIT; Printout Related Command SLPI - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 323
join to the width of the lines connected to each other. The default miter limit value is 10. In smaller miter-limit values, say 3, the miter join automatically switches to the beveled join. This switching prevents the problem of a spike extending beyond the intersection of the path because a small - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 324
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; PMZP 5, 15; SPD .5; SLJN 2; CMNT Mitered join; PDRP 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2; SMLT 10; CMNT Miter limit is 10; STRK; NEWP; PMZP 5, 19; SPD .5; SLJN 2; CMNT Mitered join; PDRP 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2, 1.5, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 325
gamma]; Parameters monitor-type: 0 = None 1 = SMPTE 240M 2 = HDTV (sRGB) [default] 3 = Sony Trinitron 4 = Apple RGB 5 = NTSC 6 = KC-RGB 7 = system or switching emulation modes resets all custom parameters to the default states. The simulation provided by this command is enabled only when the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 326
This command is irrelevant to some color printing system models. At the time of release of this manual, the command is irrelevant to model FS-5800C; and monitor-name values of 0 and 2 are valid for model FS-8000C. Resetting the printing system and switching emulation mode reset all parameters to the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 327
SPAL SPAL - Select PALette COLOR Format SPAL id; Parameter id: palette ID number: 0 to 32767 (default is 0) Function The SPAL command selects the palette to activate from among the palettes that are currently available. If no palette is associated with the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 328
The printing system rounds off all decimal values to the nearest integer value. The SPD command affects graphics segments created by DZP, DAP, DRP, DRPA, BOX, CIR, and PIE commands. It also affects the width of the line and curve segments stroked as paths. A slant line drawn by the standard graphics - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 329
SPD File !R! RES; UNIT C; STM 2; SLM 2; SLS .6; SFNT "Helvetica-Nr"; SPD 0.01; DRP 5, 0; TEXT ' 0.01 cm', N; SPD 0.02; DRP 5, 0; TEXT ' 0.02 cm', N; SPD 0.05; DRP 5, 0; TEXT ' 0.05 cm', N; SPD 0.1; DRP 5, 0; TEXT ' 0.1 cm', N; SPD 0.2; DRP 5, 0; TEXT ' 0.2 cm', N; PAGE; EXIT; Printout 0.01 cm 0.02 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 330
PRESCRIBE Command Reference SPL - Set Page Length Format SPL length; Parameter length: distance from top margin to bottom margin Function The SPL command sets the bottom margin, as measured from the top margin position in the unit value designated by the UNIT command. If an attempt is made to - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 331
SPL Printout 321 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 332
(upright) L = landscape (lengthwise) Function The SPO command instructs the printing system how to orient the page, laying text For example, if you set a top portrait margin greater than the paper width, then switch to landscape orientation, the printing system resets the top manual for details. 322 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 333
is for an A4 cassette.; SPSZ 8; PAT 16, 300; UNIT C; MZP 4, 24; BOX 6, -6; MZP 7, 24; BOX 3, -3; BLK 3, -3; MZP 4, 24; TEXT, L; TEXT 'Portrait orientation'; SPO L; MZP 12, 10; BOX 6, -6; MZP 15, 10; BOX 3, -3; BLK 3, -3; MZP 12, 10; TEXT, L; TEXT 'Landscape orientation'; PAGE; EXIT; Printout 323 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 334
PRESCRIBE Command Reference SPSZ - Set Paper SiZe Format SPSZ size-code [, ratio]; Parameters size-code: 0 = Same as the size of the paper cassette 1 = Monarch (3-7/8 × 7-1/2 inches)1 2 size to cassette size × 98% ] 1 Inoperable if ratio is specified. 2 Not supported by some print systems 324 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 335
. size-code defaults to 0 at power-up and after a reset. Size codes 10 through 12, 19, and 30 are supported only by the printing system model that handles the A3 size paper. Support for other paper sizes and reduction ratios vary depending on models. For details, see the user's manual supplied with - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 336
in the other emulations. The SRM (Set Right Margin) command also sets the right margin, but it measures from the left edge limit of the paper. File !R! RES; UNIT C; SLM 1; CMNT Emulation mode is 1 (IBM); SFNT "Univers-MdCd", 18; SLPI 4; SPW 10; EXIT; Line with 1-cm left margin and 10-cm - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 337
SPW Printout Related Command SRM 327 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 338
SRM width; Parameter width: size of right margin Function The SRM command sets the right margin, as measured from the left edge limit of the paper in the unit value designated by the UNIT command. If an attempt is made to print beyond the right margin, the characters are printed on - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 339
SRM Printout Related Command SPW 329 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 340
max. 4200 dots Function The SRO command specifies the presentation mode which defines the orientation of the raster image. If the presentation-mode is 0 (default), the printing system creates the raster image along the width of the physical page regardless of the current page orientation. With the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 341
SRO presentation-mode = 0 The width and height of the raster area are defined based on the physical page regardless of the current page orientation. The current page orientation affects the position of the current point, however. Current point Width Height Current point Width Height Portrait ( - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 342
by this command is 255. These logical operations directory map to their raster operations (ROP3). Logical operation value is eset to the default of 252 by the RES command. An error results and this command has no effect if the ROP3 value is outside the range 0 to 255. File !R! DAM; RES; MCRO - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 343
CALL DBOX,2; CALL DBOX,3; RES; EXIT; Printout SROP 333 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 344
: number from 1 to the maximum (bottom) Function The SSTK command is effective only when the optional sorter is installed to the printing system. It instructs the printing system to deliver printed pages in the sorter mode. Each specified tray receives a complete set of pages, one copy of each. If - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 345
default value is 1: the printing system's face-down tray. If an optional device such as a stacker, a document finisher, or a sorter is installed, the stacker value 2 instructs correct order. !R! PAGE; EXIT; PAGE 3 But on printers with two paper trays this file will be delivered to the face-up tray - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 346
STAT [mode]; Parameter mode: 0 = prints a user status page (default) 1 = prints a service person status page Function The STAT command instructs the printing system to print a page of status information, starting on a new page. The status page lists the software version and release date as well - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 347
STAT Sample Status Page User status page Service status page 337 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 348
PRESCRIBE Command Reference STM - Set Top Margin Format STM distance; Parameter distance: size of top margin Function The STM command sets the top margin, in the unit value designated by the UNIT command. A top margin setting in a document file should be placed at the beginning of the file or - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 349
STM Printout 339 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 350
, printing 15 copies of the job: !R! STPL 3; STPC 5; JOBS 2, 15, 1, 0, 1, "Interim Report 1", "Steve", "09/22/02 19:24"; TEXT "This is Interim Report 1 ..."; PAGE; UNIT C; BOX 5,10; PAGE; JOBT; EXIT; 1 This value depends on the stapler to be used. 340 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 351
parameter (See above.) using a document finisher incorporating the stapler unit. With position 2 (top left), stapling is automatically straightened (vertical) when Legal size paper is used. Parameter values 50 to 54 are valid for certain copier models only. The number of sheets that the stapler can - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 352
current output stack which may be specified by STAK. (For the document finisher such as the DF-31, the MSTK command may be used to guide stapled pages to one of the output trays as desired.) STPL command causes a page break. File !R! STPL 3; CMNT Two staples on the left; JOBS 0,3,0,0; TEXT - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 353
, or 1200 dots per inch. The 200, 600, and 1200 dpi resolutions are available only for the printing system models that support the 600 or 1200 dpi printing resolution. The default value is 75 dots per inch. The STR command affects only PRESCRIBE raster graphics. It does not change the resolution of - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 354
not place a line or graphic on a page because PRESCRIBE pathconstruction commands only define the path. For the path to be drawn or filled as a line, box, character, etc., on the page, the STRK command must be issued. After stroking the current path, the STRK command clears the path and moves the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 355
STRK Printout Related Commands FILL, NEWP 345 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 356
underline thickness is one dot. The maximum underline thickness is 127 dots. The default values include: • Distance below baseline: 7 dots • Thickness of underline: 4 which is an independent character with ASCII code 95 (hex 5F). If your word-processing software writes underlines by backing up and - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 357
SULP Printout 347 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 358
command is relevant to the FS-1000 printer only. Note File To attribute the MP tray for thick paper and normal density: !R! TATR 0, 1, 3; EXIT; To reset the second paper cassette (option feeder) to the defaults: !R! TATR 2; EXIT; To reset all paper sources to the defaults: !R! TATR; EXIT; 348 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 359
location. The length of the string is unlimited, except that the command as a whole may not be longer than 255 characters. Carriage-return and linefeed codes in the string are ignored. 349 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 360
Command Reference File !R! RES; UNIT C; MAP 2, 2; SFNT 'Univers-MdCd'; TEXT 'Check desired options:', L, U; FONT 2; BOX .1, -.1; TEXT 'Power steering', L; BOX .1, -.1; TEXT 'CD auto changer', L; BOX .1, -.1; TEXT 'Air conditioner', L; PAGE; EXIT; Printout Related Commands CTXT, RTXT 350 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 361
as 1-byte or 2-byte character code while printing using a text command. To parse such characters, the current font must supports 2-byte characters and a 2-byte symbol set such as Windows 3.1J (19K). The pursing method will automatically be shift JIS encoding (2) if the default font and symbol set is - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 362
1 is automatically set to the tray parameter. Function The TRSM command instructs printing system to insert blank or printed page between each transparency. The printing system loads transparency from MP tray and inserting paper from the paper source other than MP tray. When face-down printing, the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 363
UNIT - set UNIT of measurement Format UNIT code; Parameter code: I = inches C = centimeters P = points D = dots Function The UNIT command sets the unit of measurement used in other PRESCRIBE commands. The initial unit is inches. Other supported units of measurement can be calculated as follows - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 364
PRESCRIBE Command Reference Printout 354 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 365
command applies only to the printing system models that support the 600 dpi resolution. It defines the unit UNIT value be set to D. The default unit of measurement is 300 (dpi). BOX 100, 100;", L; UNIT D; UOM 120; BOX 100, 100; UNIT C; MZP 5, 9; TEXT "UOM 720; BOX 100, 100;", L; UNIT D; UOM 720; BOX - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 366
PRESCRIBE Command Reference Printout Related Command UNIT 356 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 367
is to be set for a virtual mailbox for which a password is set, that virtual mailbox's password is required. An error will be displayed on the operator panel if no password or the incorrect password is specified. (See the Technical Reference manual.) Note that if command syntax is incorrect, such as - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 368
by issuing multiple instances of this command. If no virtual mailbox corresponds to the alias given, an error will be displayed on the operator panel. (See the Technical Reference manual.) This command is irrelevant to photocopy virtual mailbox function. Note Files To stack jobs on virtual - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 369
fails or no virtual mailbox corresponds to the alias given. For error displays, see the Technical Reference manual. The master password is valid as the current password for all virtual mailboxes. Virtual mailboxes for which a password has been set are not shown on the VMB LIST page (See - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 370
PRESCRIBE Command Reference Files To set 9999 as the password for virtual mailbox number 3 for which no password is set: !R! VMPW 3, 0, 9999; EXIT; To set no password for the virtual mailbox with the alias MyMailbox for which the password 9999 had been set: !R! VMPW "MyMailbox", 9999, 0; EXIT; To - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 371
WIDE WIDE - set WIDE A4 mode Format WIDE mode; Parameter mode: 0 = Off 1 = On Function The wide A4 function widens the A4 printing width in order to prevent unnatural line breaks or clipping of graphics in cases where a document created as a letter-size document is output in A4 size. The WIDE - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 372
PRESCRIBE Command Reference WRED - WRite EnD Format WRED; Parameter None Function The WRED command terminates a sequence of writing data to the memory card or to the hard disk, using one of the commands listed below. The WRED command can be renamed to a string of ASCII characters if necessary. For - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 373
XBAR XBAR - print two dimensional barcode Format XBAR [data-length]; data-string;ENDB; or XBAR buffer-name;ENDB; Parameters data-length: length of data in bytes, terminated with a semicolon (;) If this value is omitted, data-string is counted all characters after the first semicolon until the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 374
PRESCRIBE Command Reference Files !R! XBAR; The Milky Way is a gravitationally bound collection of roughly a hundred billion stars. Our Sun is one of these stars and is located roughly 24,000 light years (or 8000 parsecs) from the center of our the Milky Way. The Galaxy has three major components. - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 375
type/reset all other XBCP parameters Format XBCP 0[, type]; Parameter type: two dimensional barcode type: 1 = PDF417 (only type currently supported) Function The XBCP 0 command selects a barcode type and resets all parameters to the defaults. File See XBCP 1 (page 366) command page. 365 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 376
Parameter element-width: narrowest bar and space width: More than or equal to 1 dot. If less than 1 dot, truncated to 1 dot. Default is 3 dots. Function PDF417 supports 8 different bar and space widths. The each width is a multiple of 1 to 8 times of the narrowest element width. The XBCP command - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 377
Parameter percentage: value between 0 and 400 Function PDF417 supports an error correction scheme. The XBCP 2 command specifies the error correction level as a percentage of the number of code word values for the data to be encoded. An illegal value defaults to 10. Note that XBCP 3, as explained on - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 378
PRESCRIBE Command Reference XBCP 3 - set error correction level Format XBCP 3, level; Parameter level: error correction level, integer from 0 to 8 Function The XBCP 3 command sets the error correction level by predetermined values. An illegal value defaults to 0. Note that the execution of - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 379
rows, ranging from 3 to 90 Function The XBCP 4 command sets the number of data code word rows in the PDF417 barcode. Illegal values make XBCP 4 ignored. XBCP 6 default provides default. Note that this command is not effective if XBCP 8 is issued. Precedence of XBCP modes is: 46, 4+8< 6. File - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 380
5 ignored.) Function The XBCP 5 command sets the number of data code word columns in the PDF417 barcode. There are also row indicator code words at each end of the row which are not counted as data code words. XBCP 6 default provides default. Note that this command is not effective if XBCP 8 is - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 381
and 1: 10 (XBCP 6, 1, 10) Function The XBCP 6 command determines aspect ratio of vertical height and horizontal width of the barcode. Illegal values default to 1: 2. Default is 1: 2. Note that this command is not effective if XBCP 4 and/or 5 is issued, however, this has the highest priority if both - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 382
PRESCRIBE Command Reference Printout Aspect ratio is 3:2 in vertical and horizontal directions. Aspect ratio is normal. 372 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 383
to element width, ranging from 1 to 10 Function The XBCP 7 command determines the bar height by a ratio to the narrowest element width. An illegal value defaults to 3. File To set the module height twice as high as the element width: !R! RES; XBCP 7, 2; XBAR;Visit Sea World, the world famous San - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 384
automatically set rows and columns so that it satisfies the requirement that the multiplication of rows times columns is less than or equal to 928. Default is disabled. Note that the XBCP 8 overrides XBCP 4 and/or 5 which set the number of rows and columns. However, this command is not effective if - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 385
XBCP 9 XBCP 9 - enable truncation Format XBCP 9; Parameter None Function The XBCP 9 command can generate a truncated PDF417 symbol that omits the right row indicator and the stop pattern. Default is non-truncation. 375 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 386
PRESCRIBE Command Reference XBCP 10 - enable file name Format XBCP 10, 'file-name'; Parameter file-name: string containing a file name Function A Macro PDF417 symbol contains an optional file name field. The XBCP 10 command enables this field and defines its contents. The string must be - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 387
block count Format XBCP 11; Parameter None Function A Macro PDF417 symbol contains an optional block count field. The XBCP 11 command enables this function. Default is not enabled. The execution of this command also automatically sets Macro PDF417 symbol mode. File !R! RES; XBCP 11; MZP 1,0; XBCP 18 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 388
PRESCRIBE Command Reference XBCP 12 - enable time stamp Format XBCP 12, time; Parameter time: total number of seconds since 00:00:00 AM January 1, 1970 Greenwich mean time Function A Macro PDF417 symbol contains an optional time stamp field. The XBCP 12 command enables this function. The - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 389
XBCP 13 XBCP 13 - enable sender ID Format XBCP 13, 'sender-id'; Parameter sender-id: string containing sender ID Function A Macro PDF417 symbol contains an optional Sender ID field. The XBCP 13 command enables this field and defines its contents. The string must be surrounded by single or - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 390
PRESCRIBE Command Reference XBCP 14 - enable addressee ID Format XBCP 14, 'addressee-id'; Parameter addressee-id: string containing addressee ID Function A Macro PDF417 symbol contains an optional Addressee ID field. The XBCP 14 command enables this field and defines its contents. The string - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 391
XBCP 15 command enables this function. Note that the execution of this command also automatically sets Macro PDF417 symbol mode. This function is disabled in default condition. File !R! RES; XBCP 15; MZP 1,0; XBCP 18,0; XBAR; ... ... EXIT; 381 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 392
. The XBCP 16 command enables this function. Note that the execution of this command automatically sets Macro PDF symbol mode. This function is disabled in default condition. File !R! RES; XBCP 16; MZP 1, 0; XBCP 18, 0; XBAR; ... EXIT; 382 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 393
XBCP 17 XBCP 17 - allow control of file ID Format XBCP 17, 'file-id'; Parameter file-id: string containing a file ID Function A Macro PDF417 symbol contains a required file ID. The XBCP 17 command allows control of this field. A random file ID is generated when XBCP 10 through 16 or XBCP 18 are - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 394
PRESCRIBE Command Reference Printout 384 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 395
PDF417 symbol mode directs the reader to separate large data and allows Macro PDF417 two dimensional barcodes with a single file-id. File To bar-code data 'abcdXYZ12345' as a Macro PDF417 using block indices 0, 1, and 2: !R! UNIT C; CMNT Set unit to centimeters; XBCP 17,"file-id"; CMNT Set file ID - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 396
PRESCRIBE Command Reference Printout 386 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 397
the current coordinate (like the MRP command described on the printing system's manual). The remaining pairs of positioning parameters are ignored if there are no positions the first barcode at 1 inch each from the left and right paper edge limits. The fourth line XBCP 19 moves the cursor 1 inch - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 398
-20-row PDF symbols at specified locations in Macro PDF mode. In example below, the first line XBCP command resets all XBCP parameters to the defaults and selects the barcode type for PDF417 (though it is the only type currently available); the second line XBCP sets the number of rows in - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 399
Printout 2 XBCP 19 File 3 To print multiple Macro PDF barcodes beyond the current page. In the example below, the fourth line XBCP 19 has no coordinating parameters specified. This allows the first segment barcode of the ensuing PDF data to be positioned at the current cursor position and the - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 400
PRESCRIBE Command Reference Printout 3 First page Second page 390 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 401
characters can include digits and special symbols such as hyphens. For example, F-1 and GRY-2 are valid buffer names. As the above Format instruction implies, the XBUF command sequence can have two other formats implementing the different functions as follows: XBUF buffer-name,; data-string;ENDB - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 402
PRESCRIBE Command Reference Files is used to delete all buffer name from the printing system memory. ... XBCP 0,1; XBUF PDF 1, 25; This is a PDF417 example. ;ENDB; XBUF PDF 2, 15; This is a test. ;ENDB; ... XBAR PDF 1; MRP 1,1; XBAR PDF 2; The sixth line prints PDF417 barcode containing the data - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 403
: number from 100 to 105 bitmap: dot pattern of the pattern, coded as a character string Function The XPAT command generates a new, expanded for creation of new patterns appear in Chapter 4 of the Technical Reference manual. File !R! RES; UNIT C; MAP 5, 5; XPAT 105;//?//?p@0p@0p@0p@0p@0p@0p - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 404
PRESCRIBE Command Reference 394 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 405
Index - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 406
40 cursor moving option, 40 Booklet binding, 38 Box, 42 cursor moving option, 42 Butt cap, , 157 Index-2 moving to, 157 Country code, 129 Cursor option, 42 Cursor position, 275 79 Data dump, 218 ending, 93 Destination image, 300 Downloading character, 147 Drawing rule (for fill), 101 Dummy sign - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 407
Gray pattern, 122 Grouping, 27 H Hard disk, 141, 246, 250, 256, 258 error codes, 136 I Image model, 299 International characters, 129 J Job, 136, 138, 140 , 145 K KCGL pen color, 297 KIR, 304 refinement level, 304 KPDL, 287 Kyocera Image Refinement, 304 L left, 307 Lightness, 155 Line, 73, 80, 82, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 408
Paper cassette grouping, 27 Paper size, 282, 324 customize, 282 enlargement/reduction, 324 Paper 80, 82, 167 Resetting the printer by emulation, 220 Resolution, 222 294 Sorter, 164, 334 addressing a tray group, 164 28, 182, 199 Status page, 336 user mode and service mode, 336 Symbol set, 65, 129 - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 409
data code word columns, 370 data code word rows, 369 error correction level, 368 error correction , 366 time stamp, 378 truncation, 375 type of paper, 348 Typeface, 294 U Underline, 346 distance and a job to store in a mailbox, 140 password, 359 printing a list of, 134 printing using command, - Kyocera ECOSYS FS-1370DN | PRESCRIBE Commands Command Reference Manual Rev 4.9 - Page 410
Rev. 4.9 2011.8
Command Reference
PRESCRIBE Commands