Kyocera ECOSYS FS-2020D PCL Barcode Flash 3.0 User's Manual
Kyocera ECOSYS FS-2020D Manual
View all Kyocera ECOSYS FS-2020D manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera ECOSYS FS-2020D manual content summary:
- Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 1
PCL Barcode Flash 3.0 User Manual - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 2
is published as the 'Application Version' on the PCL Barcode Flash status page as well. Copyright © KYOCERA Mita Europe B.V. All rights reserved. No part of this manual may be duplicated or transferred in any form or manner, either electronically or mechanically, including photocopying, recording - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 3
User Manual PCL Barcode Flash Please read this manual before installing and using the software. Keep the manual somewhere close to the printer. 3 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 4
MANUAL 6 1.2 HOW TO USE THIS MANUAL 7 1.3 PURPOSE OF THE APPLICATION 8 1.4 ITEMS PROVIDED AS STANDARD 9 1.5 ABOUT PCL BARCODE FLASH 10 1.5.1 Overview 10 1.5.2 Terminology 10 1.6 THE MAIN FEATURES OF PCL BARCODE FLASH 12 1.7 SUPPORTED 61 3.5 EXAMPLES AND INSTRUCTIONS ON USE 64 3.6 BARCODE - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 5
3.6.38 ZIP + 4 Postnet 9 102 3.6.39 ZIP + 4 Postnet 11 103 3.6.40 Datamatrix 104 3.6.41 QR code 105 3.7 EXPANDING TYPEFACES 106 3.7.1 Checking Typefaces 106 3.7.2 Activating fonts using a PRESCRIBE command 107 3.7.3 Activating fonts using a PCL command 108 3.7.4 Examples 109 4 APPENDIX 110 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 6
on how to install and use the PCL Barcode Flash software for Kyocera Mita printers and multifunction devices. Instructions on the installation and configuration of the devices can be found in the relevant installation and user manuals. You will also find here additional information on programming in - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 7
manual This manual contains information on how to use PCL Barcode Flash, and in particular information on installing and programming it. Below, we refer to the "barcode solution" for short. The performance features and programming instructions in the additional Kyocera Mita manuals included in the delivery - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 8
of the application PCL Barcode Flash enhances Kyocera Mita FS and KM devices to include additional linear the PCL activation sequences follow industry-standard formats, there are usually no problems with integrating devices equipped with the Barcode Flash solution into existing environments - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 9
, please ensure that you have the following components: - a CD containing manual files (in PDF format) and sample prints - a Compact Flash card (pre-programmed with PCL Barcode Flash software) Please complete the registration card and send this to Kyocera Mita. This will allow us to keep you up-to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 10
Flash uses a special feature of Kyocera Mita FS and KM devices: the central a completely normal workgroup printer. The barcodes already available as standard with Kyocera Mita devices can still be the PRESCRIBE IIe Programming Manual (see appendix). 1.5.2 Terminology In this manual, in most cases we - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 11
Stack codes essentially consist of up to 90 rather flat linear codes "stacked one on top of the other", so that a data density several times higher can be generated without allowing the dimensions of the codes to become excessively large. Normally, data densities fifteen times higher are achieved - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 12
prior to purchase 1.7 Supported Barcodes 1.7.1 Linear codes (one-dimensional codes) 2/5 Interleaved with check digit 2/5 Interleaved without check digit 2/5 Industrial with check digit 2/5 Industrial without check digit 2/5 Matrix with check digit 2/5 Matrix without check digit Code 93 Code - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 13
UCC-128 UPC-A UPC-A + 2-character extension UPC-E UPC-E + 2-character extension MSI Plessey MSI Plessey + Mod10 check digit MSI Plessey + Mod10 + Mod10 check digit MSI Plessey + Mod11 + Mod10 check digit ZIP+4 Postnet 5 ZIP+4 Postnet 9 ZIP+4 Postnet 11 Australia 4-State 37-CUST Australia 4-State 52- - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 14
Kyocera Mita printers and multifunction devices. At the time of publishing (version 3.00, March 2008), the following devices are supported: FS-1010 FS-1050 FS-1020D FS-1030D FS-1100 FS-1300 FS-1800 FS-1800+ FS-1900 FS-1920 FS-2000D FS-3800 FS-3820N FS-3830N FS-3900DN FS-4000DN FS-6020 FS-6950DN FS - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 15
Note The following minimum requirements for the device used should be met so that PCL Barcode Flash can run without complications: Firmware as of April 2001 or newer Min. 16 MB RAM recommended. Less RAM may lead to errors. 15 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 16
the printer settings/printer environment: - PCL Barcode Flash supports printer Printer, etc.) if they are activated. - For technical reasons, it is not possible to use a number of API programs - the barcode solution is one of these - simultaneously. Therefore, solutions produced by Kyocera Mita - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 17
the right file to the printer. Please observe the instructions in this regard at the Kyocera Mita customer service if a change between Type A and B or vice versa is necessary. Note Please note carefully the general tips on working with CF cards in your printer manual. This manual will also contain - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 18
Linedraw Code39_4 Code39_8 EAN_10mil EAN_13mil LetterGothic_10 LetterGothic_12 LetterGothic_17 USPS_ZIP OCR_A OCR_B OCR_B scal Startup ocr_a_9_land ocr_a_10_land ocr_a_9_port ocr_a_10_port ocr_b_12_ext_la ocr_b_12_land ocr_b_12_ext_po ocr_b_12_port Type B: /PRE/kmbc3-00-1 /PRE/kmbc3-00-1.inf /PRE/ - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 19
an overview of the partitions, print a partition list. Start printing this list using the front panel on the printer. Example of a partition list of Type A: The Device Information contains information on the physical size of the CF card and the memory used. The Partition Information lists print data - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 20
This information is technical in nature and the actual figures may vary depending on the software version. 20 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 21
it. To do this, you have two options: • Call the partition Barcode Init via the front panel on your printer, or • Send the PRESCRIBE sequence !R! FRPO I0, "KM BC 3.00.1"; EXIT; to the printer. If you are using a later version, the name of the newer partition must be used instead of "KM - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 22
page to hand. As a rule, the status page helps Support to help you resolve the problem more easily. The status page is divided into three sections: Font Information, Internal Barcode Information and Application Information: Font Information contains an overview of the group of barcodes and fonts - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 23
in the chapter entitled, HARDWARE INSTALLATION, there is a Startup partition on the CF card. All data on this partition is automatically loaded when the printer is switched on and is immediately available. Therefore, all additional data which you would like to make available to users must be copied - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 24
3 Programming 3.1 General Kyocera Mita printers and multifunction devices are equipped as standard with a number of linear barcodes which can be controlled exclusively using the Kyocera language PRESCRIBE. The PCL Barcode Flash software extends the number of barcodes supported to include important - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 25
instructions assume a basic knowledge of PCL programming. If you are not yet confident with using this, we recommend that you read the manuals "font numbers" of the barcodes supported individually. If you would like to the sequence is interpreted by the printer from this point on as barcode - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 26
(ASCII 32) as the stop character even if the base data contains only numeric characters. Barcodes, which permit the space character in the again. Send once again a (s#T sequence to the printer which includes the number of the font that the printer is to use for further text from now on. Some - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 27
in the case of barcode symbols. When a barcode is printed, the cursor moves to the lower right corner of the barcode symbol. See the PCL manual for how to position the cursor. Note In most cases, it is recommended after producing a barcode symbol in PCL that absolute positioning be carried out - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 28
are optional, i.e. you can omit these if your application does not require plain text, for example, or if the width and length in default form are already sufficient for the requirements of your application. Example: (s1p301h20v4b4s24670T instead of just (s24670T v parameter Height of the - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 29
p parameter Positioning of plain text 0 = Use default, cf. the defaults entered for the individual codes for this purpose 1 = no plain text Example: 2 = embedded beneath Example: 3 = half embedded beneath Example: 4 = beneath the barcode - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 30
h parameter Plain text font When you use the h parameter, this always requires a three-digit number, as you can see from the example above. First digit: Font style 1 = regular 2 = italics 3 = bold 4 = bold italics Second digit: Font size 0 = select automatically 1 = use previously selected size for - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 31
A Code 128 Subset B Code 128 Subset C UCC-128 EAN-128 Codabar Codabar + Mod16 check digit MSI Plessey MSI Plessey + Mod10 check digit MSI Plessey + Mod10 + Mod10 check digit MSI Plessey + Mod11 + Mod10 check digit ZIP + 4 Postnet 5 ZIP + 4 Postnet 9 ZIP + 4 Postnet 11 Australia 4-State 37-CUST - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 32
regards the complete sequence as a font call and not as a barcode call, so any unwanted fonts are activated and the printer attempts to print your base data instead of outputting the barcode. Warning If invalid values - i.e. values which differ from the validity ranges mentioned above - are - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 33
you would like to use one or more of the sequences mentioned in this section, you can either send these from the computer to the printer or - better in most cases - store them on the Compact Flash card in the "Startup" partition. Cf. the chapter on this partition. 33 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 34
3.3 Barcodes and Matrix codes with different parameters 3.3.1 Datamatrix Datamatrix code has a rectangular or square structure which is made up of individual square elements (black/white). The delimiting lines which are drawn on two adjacent sides and consist of alternate black and white elements on - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 35
the smallest square element of a symbol. "Symbol" refers to the combined modules in their entirety, mainly as squares or rectangles. PCL Barcode Flash supports Datamatrix only in accordance with the widely applied ECC200 procedure. Extended Channel Interpretation and Structured Append Mode are not - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 36
Rectangular symbols Symbol no . 25 26 27 28 29 30 Rows 8 8 12 12 16 16 Columns 18 32 26 36 36 48 Num. 10 20 32 44 64 98 Data capacity Alphanum. 6 13 22 31 46 72 Binary 3 8 14 20 30 47 Example of a rectangular Datamatrix symbol (symbol no. 29) Datamatrix codes can be called with both - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 37
large module sizes. If you do not enter a value, 10 is used as the default. v parameter: inversion 1 = Symbol is not printed inverted 2 = Symbol is printed v parameter, 1 or not inverted is used as the default. Examples: (s10h1v12b24820TData (s20b12,15h1v24820TData Activation with no - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 38
programming in PRESCRIBE, we recommend that you read the "PRESCRIBE IIE PROGRAMMING MANUAL". The BARC command is used. The syntax described in the PRESCRIBE manual for the BARC command is valid for the one-dimensional barcodes supported. As you will see below, the syntax for two-dimensional barcodes - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 39
The amount of base data has to be stated only if the base data is passed in the first of the ways mentioned below: 1. By means of an attachment after the semicolon that closes the BARC command, in this case the number of bytes has to be stated. 2. In inverted commas. 3. By means of an attachment - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 40
be the case, one of the lines would not be filled with useful data and the useful data would be disrupted by non-printable characters (e.g. printer control sequences) during programming. The advantage of the variant with 120 is therefore that in applications with SAP, the division of the useful data - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 41
3.3.3 QR Code This matrix code was developed by the company Denso and is particularly widespread in Japan, although more recently it has been used within the industry throughout the world. Like the Datamatrix code, the QR Code can also be printed in a variety of sizes and resolutions. QR Code - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 42
Binary: All 256 ASCII characters are accepted. Kanji: Practically all Kanji characters can be displayed. They must be available as two-byte characters in JIS X 0208 shift mode. If their encoding does not comply with the rules of the JIS Shift 0208 standard, instead of the symbol PCL Barcode Flash - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 43
in a number of respects. If PCL Barcode Flash is given the instruction in a print job to print model 1, it automatically switches to model 2. Extended Channel Interpretation (ECI mode) and Structured Append Mode are not supported by PCL Barcode Flash. Syntax in PCL The T parameter must always - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 44
standard p parameter: Error correction level Possible values: 1= 7% 2 = 15 % 3 = 25 % 4 = 30 % If you do not specify the p parameter, then 15 % is used by default. b parameter: Size of a module in dots relative to 600 dpi Permissible values: 1 - 1000, where it should be noted that a size of less - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 45
not specify the v parameter, then 1 is used by default, i.e. not inverted. Examples: (s4p10h1v12b3s24861TDaten (s12, manual. The command BARC is used. The syntax described in the PRESCRIBE manual for the command BARC applies in respect of the one-dimensional barcodes that are supported - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 46
The module size unit was previously specified using the UNIT command. We recommend that you use dots (pixels). Lowest symbol version Values from 1 to 40. For an explanation of the meaning of this parameter, cf. the explanatory notes on the h parameter in the section "SYNTAX IN PCL". Highest symbol - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 47
as address components, weight etc.). In contrast to the other 2D codes supported, the size of the individual modules as well as that of the below) that enable the reading device to locate it more rapidly. MaxiCode contains code words for the automatic correction of errors. All 256 ASCII characters - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 48
and secondary information and must appear in that order in the data. The primary information should contain information concerning the shipment. The secondary information should contain information for purposes of processing between consignor and consignee. Other data received from your carrier firm - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 49
outside of the USA. 4. Postal code 5. Country code 6. Service class Secondary information The secondary information often begins with the character string reason. All data should be entered in capital letters. The postal code may contain up to 9 digits in mode 2 (numerical) and up to 6 capital - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 50
8T Detailed explanation relative to this example: 1 = No. of symbol 1 = Number of symbols in this group 2 = MaxiCode mode 40670 = Postal code 840 = Country code 001 = Service class 1Z00004951 = Tracking number USPN = SCAC 06X610 = UPS Shipper number 159 = Julian day of pickup 50 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 51
1234567 = Shipment 1/1 = Package x of y 10 = Package weight Y = Address validation OTTO-HAHN-STRASSE 12= Ship to address MEERBUSCH= Ship to city DE = Ship to state Syntax in PRESCRIBE To control the MaxiCode from PRESCRIBE, the commands XBCP and XBAR are used. The rules for the content of - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 52
the other hand, a string must be entered in quotation marks. The postal code may contain up to 9 digits in mode 2 (numerical) and up to 6 capital letters or through 6, the entire entry XBCP 5,# is unnecessary. XBCP 6,#; Service class, which must comply with the specification. The Barcode Flash - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 53
standard in all printers and normally creates PDF417 therein. The Barcode Flash solution adds MaxiCode to the PRESCRIBE command XBAR. 3.3.5 PDF417 PDF417 is a matrix code invented by Symbol Technologies. PDF stands for 'Portable Data File'. In contrast to the other 2D codes supported, the individual - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 54
The level (degree) of error correction can also be selected by the user. Nine levels are available (0-8), whereby level 0 means 'no error correction desired'. Depending on the application and on the quality of the paper used, however, a higher level should be used. All 256 ASCII characters can be - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 55
Level 0 1 2 3 4 5 6 7 8 Error correction words 2 4 8 16 32 64 128 256 512 Example: (s3p24850T This entry means that you have selected level 3, in other words sixteen error correction words. The barcode module uses this regardless of the size of the useful data. However, you also have - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 56
Layout parameters The following applies for the parameters below: With these parameters, you can set four predefined values as subparameters. These must be separated by commas. You do not have to enter all four values if you do not wish to do so. You can also leave the b- and sparameters out - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 57
symbol with the proportion of 2 to 3 as standard. As the remaining rules for the layout of the symbol also apply, these values are always only approximations. The Barcode Flash solution always selects the most appropriate value here. 3. Y-value for the proportion of the symbol (cf. sub-parameter 2). - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 58
3.3.6 Australia 4-state barcodes The Australia Post 4-state barcode was introduced to improve sorting results and to enable the accurate selection of individual postal items. Australia Post uses a unique eight character Delivery Point Identifier (DPID), which is allocated to each delivery address in - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 59
eight numeric characters and the customer information, which have to be separated from one another by a comma. The customer information may contain the following characters: - The digits 0 to 9, the uppercase letters A to Z, the space character and the special character #. - The barcode customer - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 60
Please note that no plain text is printed with the Australia 4-state barcode. Note BARC 45, 46, 47 and 48 cannot be called from PRESCRIBE macros. 60 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 61
for you. The error messages are printed in plain text in a checked rectangle, e.g.: , or The following error messages exist: Data too long The base data. Change the base data or use a different barcode, which contains the character in its character set. If, for instance, the error message - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 62
. Comma expected In the Australia Post 4-state barcode the DPID has to be separated from the customer information by a comma. The base data did not contain a comma. Wrong DPID Only eight-character digits are accepted as the DPID In the Australia Post 4-state barcode. Wrong space The base data is not - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 63
Codabar. Codabar only allows the letters A,B,C and D as stop characters. Internal error These errors should not really occur. Should any occur, then please contact your Support representative. 63 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 64
instructions on use Do not set the toner density to the lowest contrast value. It is recommended that you set it to a density of 3 or higher. The setting can be made using the control panel or the PRESCRIBE sequence !R! FRPO D4,3;EXIT; The Toner can only be done manually by careful programming and/ - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 65
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 74 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 11 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 66
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 74 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 13 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 67
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 6 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 68
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 8 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 69
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 50 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 7 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 70
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 50 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 9 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 71
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 50 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 12 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 72
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 62 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 12 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 73
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 62 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 14 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 74
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 62 p parameter 3 b parameter 8,16,24,32 Additional properties: Size of base data: 17 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 75
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 2, 4, 6, ... ,98, 100 (even number) Character set: 0 to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 76
12 Interleaved 2 of 5 with check digit Type / properties: Linear code Activation sequence: (s24641T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 77
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 2, 4, 6, ... ,98, 100 (even number) Character set: 0 to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 78
3.6.14 Industrial 2 of 5 (25) with check digit Type / properties: Linear code Activation sequence: (s24651T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 79
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 2, 4, 6, ... ,98, 100 (even number) Character set: 0 to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 80
3.6.16 Matrix 2 of 5 with check digit Type / properties: Linear code Activation sequence: (s24661T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 81
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,18 Additional properties: Size of base data: 1 to 100 Character set: 0 to 9, A to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 82
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,18 Additional properties: Size of base data: 1 to 100 Character set: 0 to 9, A to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 83
39 + Mod47 with check digit without space character Type / properties: Linear code Activation sequence: (s24671T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 84
Code 39 + Mod47 with check digit with space character Type / properties: Linear code Activation sequence: (s24673T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 85
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,18 Additional properties: Size of base data: 1 to 100 Character set: All printable - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 86
22 Code 39 Extended + Mod47 check digit Type / properties: Linear code Activation sequence: (s24681T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 87
s24690T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12,18,24 Additional properties: Size of base data: 1 to 100 Character set: 0 to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 88
s24691T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12,18,24 Additional properties: Size of base data: 1 to 100 Character set: All - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 89
Base Data> For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 1 to 100 Character set: All printable characters from ASCII - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 90
Base Data> For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 1 to 100 Character set: All printable characters from ASCII - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 91
Base Data> For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 1 to 100 Character set: All printable characters from ASCII - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 92
Data> For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: 1 to 100 Character set: 0 to 9 Example: (s24704T1234567890 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 93
s24710T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12,18,24 Additional properties: Size of base data: 15 to 21 Character set: 0 to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 94
(s24720T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12,18,24 Additional properties: Size of base data: 1 to 44, maximum size is - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 95
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter Additional properties: Size of base data: Character set: Start and stop characters: 1 to 32 0 to - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 96
3.6.32 Codabar + Mod16 check digit Type / properties: Linear code Activation sequence: (s24751T For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter p parameter b parameter - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 97
For an explanation on selecting the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12 Additional properties: Size of base data: 1 to 14 Character set: 0 to 9 Example - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 98
MSI Plessey + Mod10 check digit Type / properties: Linear code Limitation: Plain text is only output in the default typeface in a set the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12 Additional - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 99
Plessey + Mod10 + Mod10 check digit Type / properties: Linear code Limitation: Plain text is only output in the default typeface in a set position the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 100
Plessey + Mod10 + Mod10 check digit Type / properties: Linear code Limitation: Plain text is only output in the default typeface in a set position the stop character and the optional parameters, see chapters 3.2.1. and 3.2.6. Default - parameters: v parameter 29 p parameter 1 b parameter 6,12 - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 101
: Linear code, used in postal traffic within the U.S.A. Limitation: Plain text is not recommended. This code can only output plain text in the default typeface in a set position below the code. Activation sequence: (s24770T For an explanation on selecting the stop - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 102
: Linear code, used in postal traffic within the U.S.A. Limitation: Plain text is not recommended. This code can only output plain text in the default typeface in a set position below the code. Activation sequence: (s24771T For an explanation on selecting the stop - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 103
: Linear code, used in postal traffic within the U.S.A. Limitation: Plain text is not recommended. This code can only output plain text in the default typeface in a set position below the code. Activation sequence: (s24772T For an explanation on selecting the stop - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 104
3.6.40 Datamatrix Printing examples: The following text is printed out with different parameters as the DataMatrix symbol: 'Data Matrix is a two-dimensional matrix symbology which is made up of square modules arranged within a perimeter finder pattern that is used for finding the symbol and - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 105
3.6.41 QR code Printing examples: The following text is printed out with different parameters as the QR Code symbol: 'QR CODE IS A MATRIX SYMBOLOGY CONSISTING OF AN ARRAY OF NOMINALLY SQUARE MODULES ARRANGED IN AN OVERALL SQUARE PATTERN INCLUDING A UNIQUE FINDER PATTERN LOCATED AT THREE CORNERS OF - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 106
Expanding typefaces PCL Barcode Flash expands the integrated default printer typefaces to include Letter Gothic, Line Draw some Microsoft Windows standard printer drivers, and Kyocera Mita devices can now be used for this too. 3.7.1 Checking Typefaces It is possible to check that the typefaces work - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 107
pair of commands, CSET and FSET (CSET and FSET should always be used together as otherwise the font activation cannot be correctly recognised by the printer). The zero character is displayed as 0 and it should not be confused with the letter O! Barcode 3 of 9; 8.1 cpi; 12 point: FONT 830; or CSET 0Y - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 108
3.7.3 Activating fonts using a PCL command In the PCL emulation of Kyocera Mita devices, the fonts can also be selected using the corresponding PCL command. The Escape character (ASCII character 27 in decimal or 1B in hexadecimal is - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 109
3.7.4 Examples Print out a barcode 39 with PRESCRIBE: !R! FONT 831; TEXT "*0987654321*"; PAGE; EXIT; ("*" required as the start and stop character) Print out of a UPC barcode with ORC-A script embedded below in PCL: [cr][lf] [esc](8Y[esc](s1p12v0s0b0T(012345-GHIJAF([cr][lf] (012345-GHIJAF([cr][ - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 110
purchased from www.iso.ch It is generally recommended that you familiarise yourself with the following official manuals, which are normally included on CD as a PDF document with every Kyocera Mita device: - PRESCRIBE IIe Programming Manual (English) - PDF417 Two Dimensional Bar Code Implementation - Kyocera ECOSYS FS-2020D | PCL Barcode Flash 3.0 User's Manual - Page 111
111 v.3.0 EN 07-2008
PCL Barcode Flash 3.0
User Manual