Kyocera KM-1650 PRESCRIBE Commands Command Reference Manual Rev 4.8
Kyocera KM-1650 Manual
View all Kyocera KM-1650 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera KM-1650 manual content summary:
- Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 1
PRESCRIBE Commands Command Reference - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 2
or errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in the printer's firmware. Regarding Tradenames: PRESCRIBE is a registered trademark of Kyocera Corporation - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 3
model, refer to the User's Manual. Helvetica, Palatino and Times are to three printers. If you need to have access to the fonts on more than three printers, you the terms of this License and such failure is not remedied within thirty (30) is free from all bugs, errors and omissions. 8. THE PARTIES - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 4
This page is left blank intentionally iv - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 5
MPS Commands 10 PRESCRIBE Commands 11 ACLI - Add CoLor by Index 12 ALTB A - [ALlocate TaBle] Assign user-defined character table --------- 14 ALTB C - [ALlocate TaBle] Convert character code 15 ALTB D - [ALlocate area 55 CLSP - CLoSe Path 57 CMNT - CoMmeNT 59 CMOD - Color MODe 60 COPY - set - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 6
98 EXIT - EXIT from PRESCRIBE mode 99 FDIR - MP tray Feed DIRection 100 FILL - FILL closed path 101 FLAT - set FLATness 104 FLST - print Font LiST 105 FOLD - FOLD printed pages 107 FONT - change current FONT 108 FPAT - generate Fill PATtern 110 FRPO - Firmware RePrOgram 112 FRPO INIT - FRPO - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 7
- offset ReGiSTration 225 RPCS - Return to Previous Code Set 226 RPF - Return to Previous Font 227 RPG - Return to Previous Graphics state 228 RPP - Return to Previous Position 230 RPPL - Return to Previous PaLette 232 RPU - Return to Previous Unit 233 RTTX - RoTate TeXt 234 RTXT - print - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 8
264 SCAP - Set line CAP 266 SCCS - Save Current Code Set 268 SCF - Save Current Font 270 SCG - Save - Save Current Unit 283 SDP - Store Dash Pattern 285 SEM - Set Emulation Mode 287 SETF - paper STAcKer 335 STAT - STATus 336 STM - Set Top Margin 338 STPC - set STaPle Counter 340 STPL - - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 9
353 UOM - Unit Of Measurement per dots 355 VMAL - Virtual Mailbox ALias 357 VMOB - Virtual Mailbox Output Bin 358 VMPW - set Virtual Mailbox PassWord 359 WIDE - set WIDE A4 mode 361 WRED - WRite EnD 362 XBAR - print two dimensional barcode 363 XBCP 0 - select barcode type/reset all other XBCP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 10
Contents-vi - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 11
PRESCRIBE Command Reference - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 12
type ATtribute 162 MPTE MP Tray Empty 166 MTYP select Media TYPe 172 OTRY select paper Output TRaY 177 PSRC select Paper SouRCe 213 RCLT Rotated CoLlaTion 217 RES RESet 220 RESL select RESoLution 222 RGST offset ReGiSTration 225 RPU Return to Previous Unit 233 SCSZ Set - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 13
These commands are used to set the top, bottom, right, and left margins must be at least one line below the top margin. • It is not possible to specify The margins and page orientation can be reset by using the RES command. Command Top Margin 338 Margins and page orientation are more fully - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 14
, there are commands to download fonts to the printing system from an external source, and to generate fonts. Command Function Page ALTB A [ALlocate TaBle] Assign user-defined character table 14 ALTB C [ALlocate TaBle] Convert character code 15 ALTB D [ALlocate TaBle] Delete user-defined - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 15
MoDe 119 INTL InterNaTionaL characters 129 LDFC LoaD Font Character 147 LDFN C generate bitmap character for LoaDing FoNt 149 LDFN F create header for LoaDing FoNt 151 LDFN S LoaD truetype FoNt 153 RPCS Return to Previous Code memory then to return to that position stored in memory. - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 16
memory. Downloadable fonts can be particularly taxing on printing system memory, producing unexpected print results. It may be possible to correct the problem by removing some of the downloaded XPAT generate eXpanded fill PATtern 393 Path Mode Graphics Commands The following commands provide a - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 17
Overview of PRESCRIBE Commands by Function Command Function Page FILL FILL closed path 101 FLAT set FLATness 104 NEWP start NEW Path 176 PARC a color palette, assign colors to a palette, and specify colors. In this manual, color commands are marked with COLOR under the command name. 7 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 18
MODe 60 CPAL Control PALette 63 GRAY represent GRAY 124 GRRD GRaphic data ReaD 125 HUE adjust HUE 127 LGHT adjust LiGHTness 155 MCLR Match print barcodes with check digits added. Command BARC ENDB XBAR two dimensional barcode select barcode type/reset all other XBCP parameters, etc. - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 19
END Dump 93 RDMP Received-data DuMP 218 External Media Control Commands If an external storage, such as JEIDA Ver. 4 memory card or CompactFlash card, or a hard disk, is installed in the printing system, the following commands can be used to write data to or read from it. These commands do - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 20
trays 32 BKLT print in BooKLeT binding 38 CSTK select Collator STacKer 68 DUPX select/deselect DUPleX mode 84 DXPG select DupleX PaGe side 85 FOLD FOLD printed pages 107 JOG JOG output stacks for separation 145 MID Multi-tray ID MPS added MPS Storage 165 VMAL Virtual Mailbox ALias - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 21
or by pressing the panel keys. The User's Manual provides a full description of the control panel functions. Many PRESCRIBE commands can be embedded commands within word processing software. This support depends upon the emulation mode and the software. See Emulation of the Technical Reference - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 22
palette or the Pantone color palette. If an index number larger than the palette size is given, this command is also ignored. If a color is added to the existing index number, the current color for that index number is automatically replaced with the new color. To add a color in a palette, the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 23
File !R! RES; DAM; UNIT C; SFNT 'AntiqueOlive-Bd', 20; CPAL C; SPAL 1; CID 0, 1; ACLI 1, 0, 0, 255; ACLI 2, 0, 255, 0; ACLI 3, 255, 0, 0; MZP 1, 1; SCOL 1; TEXT 'This line is printed in blue.'; MZP 1, 2.4; SCOL 2; TEXT ' - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 24
PRESCRIBE Command Reference ALTB A - [ALlocate TaBle] Assign user-defined character table Format ALTB A, table-id; Parameter table-id: number identifying the character table assigned to the resident font, from 1 to 65535 Function The ALTB A command assigns the user-defined character table to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 25
ALTB C ALTB C - [ALlocate TaBle] Convert character code Format ALTB C, table-id, source-character, target-character; Parameters table-id: number identifying the character table to convert the character, from 1 to 65535 source-character: character code before conversion: 1-byte code = 0 to 255; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 26
character table Format ALTB D, table-id; Parameter table-id: number identifying the character table, from 1 to 65535, to be deleted Function The ALTB D command deletes the character table defined by the user. If the table to be deleted is currently allocated to the resident font (see ALTB - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 27
ALTB E ALTB E - [ALlocate TaBle] End defining combination characters Format ALTB E; Parameter None Function This command command. (page 20). The registered combined characters can be printed by specifying the character code which was assigned at the time of definition. Related Command ALTB S 17 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 28
PRESCRIBE Command Reference ALTB G - [ALlocate TaBle] Generate user-defined table Format ALTB G, table-id, table-format; Parameters table-id: table ID number: 1 to 65535 table-format: 1 = 1-byte, character codes 0 to 255 2 = 2-byte, character codes 0 to 65533 Function The ALTB G command - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 29
ALTB R ALTB R - [ALlocate TaBle] Release user-defined character table Format ALTB R, table-id; Parameter table-id: number identifying the character table to be released Function The ALTB R command terminates the assignment of the user-defined character table for the current resident - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 30
ALlocate TaBle] Start to define the combination character Format ALTB S, table-id, code[, width, height[[, x-coordinate, y-coordinate, [paint-mode]]]; Parameters table-id: number identifying the character table to define the combination character, from 1 to 65535 code: character code in units - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 31
JIS code width: character width: the value from 1 to the character width specified by ALTB S (page 20) height: character height: the value from 1 to the character height specified by ALTB S (page 20) x-coordinate: X coordinate of the reference point, integer value calculated in 1000 unit basis - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 32
PRESCRIBE Command Reference File !R! res; unit c; SFNT 'TimesNewRoman', 48; ALTB G, 1000, 1; ALTB A, 1000; ALTB S, 1000, 64, 1800, 1000; ALTB T, 77, 700, 700, 0, 700; CMNT M; ALTB T, 65, 700, 700, 630, 700; CMNT A; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 33
ALTF ALTF - change to ALTernate Font Format ALTF alternate-number; Parameter alternate-number: a number from 0 to 47 Function The ALTF command changes the current font to a font designated by an alternate number. The actual font assigned to this alternate number is set by a previous SETF - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 34
PRESCRIBE Command Reference File !R! RES; SFNT "Helvetica-Nr", 12, 1000; SFNT "TimesNewRoman-It", 11, 1001; SETF 1, 1000; SETF 2, 1001; MCRO BIBLIO; ALTF 1; TEXT %1, E; TEXT " ", E; ALTF 2; TEXT %2, E; TEXT " ", E; ALTF 1; TEXT %3, N; ENDM; ALTF 1; TEXT "Bibliography", N, U; TEXT, N; CALL BIBLIO, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 35
filled in with different text. The AMCR command closely resembles the CALL command; therefore, the user unit of measurement, underline parameters, and fill pattern. When the automatic macro is enabled with mode mode set to D is encountered or the printing system is switched off. Note that mode - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 36
PRESCRIBE Command Reference File !R! RES; MCRO CROPMARK; UNIT C; MZP 2.46, 3.96; SCP; SCP; SCP; MRP -.635, 0; DRP -1.9, 0; RPP; 0; DRP -1.9, 0; RPP; MRP 0, .635; DRP 0, 1.9; RPP; ENDM; AMCR E, CROPMARK; PAGE; UNIT C; SLM 3.6; STM 5.2; EXIT; The text starts here. Printout Related Command CCPY 26 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 37
paper source for bulk printing. The MP tray cannot be assigned to a group. All 6 parameters must be given even though the printer has less than 6 cassettes installed. For missing cassette numbers, specify 0. The printing system will automatically switch between the paper cassettes in the group when - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 38
of arc outer-radius: outer radius of arc start-angle: starting angle end-angle: ending angle Function The ARC command works in the standard graphics mode. It draws a filled-in arc-shaped area extending from the inner radius to the outer radius, and from the starting angle to the ending angle - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 39
ARC File !R! RES; UNIT C; MAP 5, 8; PAT 52; ARC 1, 2, -45, 45; MAP 5, 10; PIE 2, 0, 10, 20, 30; ARC 0, 2, 0, 60; PAT 20; ARC 0, 2, 60, 180; PAT 10; ARC 0, 2, 180, 360; PAT 1; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 40
PRESCRIBE Command Reference Printout Related Command PARC 30 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 41
external characters for FoNt Format ASFN mode, font-number; Parameters mode: A = assign external characters R downloaded in the printing system as an external font by using the LDFC or LDFN command. For the print systems supporting 2-byte font system, if the user-defined font is a 1-byte code - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 42
's permanent memory while the power is off, or until it is changed by another ASTK command. It is ignored in the normal sorter mode (FRPO S0, 0;) but the printing system automatically sets up the previous tray group setting when the sorter is again switched to the multiple environment mode (FRPO - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 43
ASTK File The following command sequence delivers print jobs to trays 4, 5, 6, and 7 (the second group). !R! FRPO S0, 1; CMNT Enter multiple sorter mode; ASTK 3, 7, 9; CMNT Create three groups; MID 2; CMNT Send the output to 2nd grp.; SSTK; CMNT Sort; EXIT; Related Commands CSTK, MID, MSTK, SSTK 33 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 44
12 = EAN-13 (Truncated JAN) 13 = DUN-14 (Distribution Unit Number, EAN) 14 = DUN-16 (Distribution Unit Number, EAN) 15 = MSI with no check digit 16 = = Code 128 (manual mode change) 24 = Code 128 (auto mode change) 25 = Code 11 with only 'c' 26 = Code 11 with both 'c' and 'k' checksum 27 = Code 93 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 45
BARC 43 = CUSTOM CODE (Japan)1 44 = CODABAR with no check digit ( . Height of all bars in other cases. Default value is 1.52cm (0.6 inches, 180 dots). The unit of measurement is determined by the UNIT command. Minimum value 0.254cm (0.1 inch, 30 table below. 1 FS-600/FS-7000/FS-9100/FS-9500 only 35 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 46
PRESCRIBE Command Reference Table 20 Characters that can be used Type Max Characters to be used Default 0 11 0123456789 0 1 13 0123456789 0 2 16 0123456789 0 3 13 0123456789 0 4 18 0123456789 0 5 22 0123456789 0 6 25 0123456789 0 7 29 0123456789 0 8 6 0123456789 0 9 8 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 47
20 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ 44 3 - 32 $+-./0123456789:abcdetn* and spaces Default 0 0 - Length of the bars For the UPC and 200dots It is recommended to use the dot for the unit of width in order to avoid the translation error by the barcode reader. The example below specifies the width - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 48
binding: number representing binding mode: 0 = None 1 . Booklet printing requires the hard disk to be installed in the printing system. a = First page refer to the SPSZ command page in this manual. The document must have the same page printing is also possible by adding the DUPX command. To - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 49
to left This command is not supported by some photocopier models. The following command sequence prints a copy of a 12-page A4 document in booklet mode, folding the stack in the middle. The printing system will require A4-R paper to be loaded. !R! RES; SPSZ 8, 5; UNIT C; BKLT 1; DUPX 2; FOLD; SFNT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 50
-in BLocK Format BLK width, depth[, option]; Parameters width: width of the block depth: depth of the block option: B = Leave the cursor unmoved (Default) H = Move the cursor to the horizontally adjacent corner V = Move the cursor to the vertically adjacent corner E = Move the cursor to the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 51
BLK File !R! RES; UNIT C; MAP 5, 5; PAT 20; BOX 4, 1; BLK 4, 1; MRP 0, 1.5; BOX 4, 1; BLK 4, 1; MRP .9, .6; SFNT "Helvetica-Nr"; TEXT 'OVERPRINTING'; MRP 0, 5; PAT 29; BOX 1, -4; BLK 1, -4, H; PAT 39; BOX 1, -3; BLK 1, -3, H; PAT 49; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 52
box depth: depth of the box option: B = Leave the cursor unmoved (Default) H = Move the cursor to the horizontally adjacent corner V = Move the The size and thickness is measured on the basis of value established in the UNIT command. The cursor is moved as specified by the option. If the option - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 53
BOX MAP 4, 0; SCP; SFNT "Helvetica-Nr", 10; BOX 4, 2, L; TEXT 'Text printed with option L'; RPP; BOX 4, 2, N; TEXT 'Text printed with option N'; PAGE; EXIT; Printout 43 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 54
. If the repeat count is omitted, the macro is executed once. Only the first four characters of the macro name are significant. They must match the first four characters of a macro name defined by a previous MCRO command. A parameter value consists of the characters that occur between the delimiting - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 55
File !R! RES; UNIT C; SLS .5; CMNT Requires BX and SCREEN macros; CMNT See ENDM command page; MAP 9, 3; CALL BX; MAP 7, 4; CALL 5 BX; MAP 5, 5; CALL 9 BX; MAP 8, 6; CALL SCREEN, 2.2, 1.7; MAP 8.6, 7; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 56
CoPY Format CCPY mode; Parameter mode: E = enable CROPMARK macro printing the page on the paper fed from cassette #2. The third line applies to the second page , and so on. It is possible to add as many lines as required to match the number of pages of the document to print. CCPY E; PSRC 2; AMCR - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 57
CCPY File !R! RES; DAM; CCPY D; UNIT C; MCRO COVER; UNIT C; SFNT 'Helvetica-Bd',14; TEXT 'Registration Form', L; SFNT 'Helvetica', 9; TEXT 'Please provide your personal details:'; MRP 0, .2; BOX 6, 1; MRP 0, .35; TEXT ' Your Name'; ENDM; MCRO MAIL; UNIT C; SFNT 'Helvetica-Bd',14; TEXT 'Mailing - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 58
PRESCRIBE Command Reference Printout 48 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 59
CDSK CDSK - Check hard DiSK Format CDSK; Parameter None Function The CDSK command verifies data in the hard disk (garbage collection). It deletes garbage jobs such as page image data that were accidentally generated in the hard disk and normally inaccessible for deletion. File !R! CDSK; EXIT; 49 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 60
) 1 = Device-dependent CMY 2 = Void 3 = CIE L*a*b encoding: Pixel encoding 1 = Indexed by Pixel (Default) 3 = Direct by Pixel Function The CID command creates a new color palette using the ID which is assigned to the currently active palette. Note that the currently active palette is deleted by this - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 61
CID File !R! RES; DAM; UNIT C; SFNT 'Helvetica-Bd', 20; CPAL C, 1; SPAL 1; CID 0, 1; CMNT RGB Color Space used; ACLI 1, 0, 0, 255; MZP 1, 1; SCOL 1; TEXT 'An RGB color palette is used.' CID 3, 1; CMNT L*a*b - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 62
. The line thickness used is designated by the SPD command. A circle can also be drawn by using the path mode graphics. Refer to the PARC command. File !R! RES; UNIT C; SLS .5; SPD .01; MAP 10, 1; CIR .1; MRP 0, .1; CIR .2; MRP 0, .2; CIR .4; MRP 0, .4; CIR .8; MRP 0, .8; SPD .02; CIR 1.6; MRP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 63
CIR Printout 53 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 64
PRESCRIBE Command Reference CLIP - CLIP current path Format CLIP [clip-mode]; Parameter clip-mode: 1: EO clip 2: Non-zero winding clip Function The CLIP command sets the current path as the clipped path. After this command is issued, no painting - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 65
segments drawn in the standard mode graphics. Any painting operations outside the specified rectangle is erased and those segments within it are painted on the page. The coordinates are measured from the top and left edge limits in the units designated by the UNIT command. If the parameters are - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 66
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; SPD 1; PMRA 6, 9, 3, 0; PAT 1; PARC 6, 9, 3, 0, 360; CLPR 3, 6, 9, 12; STRK; PAGE; EXIT; Printout 56 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 67
closes an open path by adding a line segment extending from the end of the path to the beginning of the path. Simply ending a path at the path's starting point does not make it a closed path; such a path remains open until it is closed UNIT C; NEWP; CMNT The 1 st path below is stroked without closing - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 68
PRESCRIBE Command Reference Printout Related Command NEWP 58 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 69
CMNT CMNT - CoMmeNT Format CMNT string; Parameter string: any character string Function The CMNT command adds a character string, typically a comment explaining the purpose of the following PRESCRIBE commands. The CMNT command statement will be ignored by the printing system. Although character - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 70
PRESCRIBE Command Reference CMOD - Color MODe COLOR Format CMOD mode; Parameter mode: color mode: 0 = Monochrome 1 = Color (Default) Function The CMOD command switches between monochrome and color modes. In monochrome mode, other color commands are still enabled, but printing is converted to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 71
another COPY command or by issuing a reset command. For best results, place the copy command near the start of a job or at the top of a page. If two or more copy commands are placed on the same page, the last one will be recognized. File !R! RES; SLM 0.5; UNIT P; SFNT 'Helvetica-Bd', 14.4; SLS - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 72
PRESCRIBE Command Reference Printout 62 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 73
for another palette. The palette ID number is reset to 0 by RES command. Mode A deletes all existing palettes and brings the default palette back to the default state (ID 0). Note that non-active palettes are not deleted. Also, palette-id is not used when mode is A. Mode S deletes all palettes that - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 74
PRESCRIBE Command Reference CPTH - Character PaTH Format CPTH 'string'; Parameter string: any character string except from ASCII code 31 (hex 1F) and lower Function The CPTH command constructs a path which adds the outlines of characters to the current path. When stroked or filled, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 75
CSET CSET - Change symbol SET by symbol-set ID Format CSET symbol-set-id; Parameter symbol-set-id: symbol set ID: 0D = ISO 60 Norway 0E = Roman Extension 0F = ISO 25 French 0G = HP German 0I = ISO 15 Italian 0K = ISO 14 JIS ASCII 0N = ECMA- - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 76
PRESCRIBE Command Reference 9R = Windows 3.1 Latin/Cyrillic 9T = PC-Turkish 9U = Windows 3.0 10G = PC-851 Latin/Greek 10J = PS Text 10N = ISO8859/5 Latin/Cyrillic 10R = PC-855 Cyrillic/Serbia 10U = IBM PC-8 11G = PC-869 Latin/Greek 11U = IBM PC-8 Danish/Norwegian 12G = PC-8 Latin/Greek 12J = - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 77
of alphabetic, numeric, and symbolic characters. The CSET command summons the symbol set to suit the various languages with the current font. The factory default symbol set is 0U (US ASCII). When the FSET command is used to select a font, the printing system selects a font based on a prioritization - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 78
(bottom) Function The CSTK command is effective only when the optional sorter is installed to the printing system. It instructs the printing system to deliver printed pages to the sorter in the collator mode. Each tray specified receives all copies of one page. The copies of the first page go - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 79
of the string is unlimited, except that the command as a whole may not be longer than 255 characters. Carriage-return and linefeed codes in the string are ignored. File !R! RES; SLPI 3; SFNT "Helvetica-Bd", 16; MAP 4, 1; CTXT 'NEWS!', L, U; SFNT "TimesNewRoman-It", 16; CTXT 'Unforgettable Holidays - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 80
PRESCRIBE Command Reference Printout 70 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 81
and the font numbers assigned to scalable fonts by the SFNT command from the printing system's memory. This enables the user to make room for new fonts, macros, and graphics. File !R! UNIT P; SLS 16; SFNT 'Helvetica-Bd', 15, 2000, 277, 2, 0; SFNT 'Helvetica', 15, 2001, 277, 1, .5; FONT 10; TEXT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 82
all macro definitions made by using the PRESCRIBE MCRO command from the printing system's memory. This enables the user to make room for new macros, fonts, or graphics. File !R! RES; UNIT C; CMNT Print ENDM file first.; SFNT "Helvetica-Bd"; MAP 5, 4; CALL SCREEN, 9.2, 1.7; MAP 7, 5; TEXT 'This - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 83
top and left margins. The thickness of the line is designated by the SPD (set pen diameter) command. The coordinates and line thickness are measured in the units designated by the UNIT . The DAP command is ignored in the path mode graphics. File !R! RES; UNIT C; CMNT Tree Diagram; STM 8; SLM 8; MAP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 84
PRESCRIBE Command Reference Printout 74 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 85
overflow occurs, the printing system gives an overflow warning message.) The amount of memory still available can be viewed on a status page, available by executing the STAT command. File !R! UNIT P; SLS 16; SFNT 'Helvetica-Bd', 15, 2000, 277, 1.5, 0; SFNT 'Helvetica', 15, 2001, 277, 1, .5; FONT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 86
Format DELM macro-name; Parameter macro-name: name defined by a previous MCRO command Function The DELM command deletes a specified macro definition from the printing system's memory to make room for new macros, fonts, or graphics, or so that the same name can be used for another macro. 76 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 87
File !R! UNIT C; MCRO BX; SPD .05; BOX .8, -.8; MRP 1, 0; ENDM; MCRO SCREEN %, width, depth; CMNT Draws box with rounded corners; CMNT Leaves cursor at previous position; SPD .08; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 88
black. The DPAT command does not affect the line drawn by the standard graphics commands such as DRP, BOX, ARC, etc. File !R! RES; UNIT C; MCRO DPAT; NEWP; SPD .2; SCP; SFNT "Helvetica-Nr", 10; TEXT 'DPAT %1'; PMRP 1.4, -.1; DPAT %1; PDRP 9, 0; RPP; PMRP 0, .7; STRK; ENDM; MZP 5, 5; FONT 13; CALL - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 89
DPAT Printout Related Command SDP 79 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 90
or negative. The DRP command is ignored in the path mode graphics. To add a line segment to a path, use the PDRP (in Path, Draw to Relative Position) command. File !R! RES; UNIT C; SPD .3; CMNT Cube; MZP 5, 10; DRP 4, 0, 2, -2, 0, -4, -4, 0, -2, 2, 0, 4; MRP 4, 0; DRP 0, -4, -4, 0, 4, 0, 2, -2; PAGE - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 91
DRP Printout Related Command PDRP 81 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 92
the current cursor position, with the thickness designated by the SPD command. This command is ignored if placed within a path. File !R! RES; UNIT C; MAP 2, 11; DRPA 2, 72; DRPA 2, 0; DRPA 2, 144; DRPA 2, 72; DRPA 2, 216; DRPA 2, 144; DRPA 2, 288; DRPA 2, 216; DRPA 2, 0; DRPA 2, 288; PAGE; EXIT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 93
DRPA Printout 83 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 94
binding Function The DUPX command is effective only when the option duplexer is installed to the printing system. It instructs the printing system to select or deselect duplex printing and sets the binding mode. Portrait, long-edge Portrait, short-edge Landscape, long-edge Landscape, short-edge - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 95
next side (the same as form feed) 1 = Select front side 2 = Select back side Function The DXPG command is effective only when the option duplexer is installed to the printing system. It ends printing on the current page in the same manner as a form feed. However, unlike the form feed, it also - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 96
printing on both sides of the page. !R! CMNT Initiates a PRESCRIBE command sequence; RES; CMNT Causes a page break and resets parameters; DUPX 2; CMNT Selects duplex mode, short-edge binding; SPO P; CMNT Selects portrait orientation; STAK 1; CMNT Select face-down delivery; EXIT; This text prints - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 97
position to a position specified relative to the top and left edge limits of the paper. The thickness of the line is designated by the SPD (set pen diameter) command. The coordinates and line thickness are measured in the value designated by the UNIT command. The coordinates should be positive or - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 98
PRESCRIBE Command Reference Printout Related Command PDZP 88 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 99
-name [, parameter...]; Parameters mode: E = enable automatic macro D = disable automatic macro paper-source: 0 = multi-purpose feeder 1 = cassette 1 (printing system's cassette) 2 = cassette 2 3 = cassette 3 4 = cassette 4 5 = cassette 5 6 = cassette 6 (bottom) 99 = envelope or universal feeder - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 100
PRESCRIBE Command Reference Function The EMCR command allows separate auto macros to be assigned for each of the separate paper sources. In duplex printing, it is also possible to assign separate auto macros for both the front and back sides of a page. The following commands are invalid within a - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 101
18 is executed, it is used alone, without association with XBAR or XBUF. For details on two-dimensional barcodes, see Section 5.2. of the Technical Reference manual. 91 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 102
PRESCRIBE Command Reference ENDC - END carbon Copy Format ENDC; Function The ENDC command ends definition of the CCPY E command sequence. For details, refer to the CCPY command. 92 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 103
ENDD ENDD - END Dump Format ENDD; Parameter None Function The ENDD command ends a hexadecimal dump initiated by the RDMP (Received-data DuMP) command and returns to the PRESCRIBE command mode. File See RDMP on page 218. Related Command RDMP 93 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 104
ENDM - END Macro Format ENDM; Parameter None Function The ENDM command ends a macro definition and returns to the PRESCRIBE command mode. File !R! RES; DAM; UNIT C; MCRO BX; SPD .05; BOX .8, -.8; MRP 1, 0; ENDM; MCRO SCREEN %, width, depth; CMNT Draws box with rounded corners; CMNT Leaves - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 105
Printout ENDM Related Commands CALL, DAM, DELM, MCRO 95 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 106
File The following example prints an illustrated crown using the RVRD and ENDR. !R! RES; DAM; DAF; UNIT C; SRO 1; MAP 5, 5; RVRD; 5, 0, 0, 7, 0, 0; 5, 0, 0, 24, 192, 0;5, 0, 0, 32, 32, 0; 5, 0, 0, 64, 16, 0; 5, 0, 0, 64, 16, 0; 5, 0, 0, 128, 8, 0; 5, 0, 0, 128, 8, 0; 5, 0, 0, 128, 8, 0; 5, 0, 0, 64 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 107
ENDR 5, 0, 160, 96, 80, 0; 5, 1, 24, 1, 136, 0; 5, 14, 134, 6, 23, 0; 5, 48, 65, 248, 32, 192; 5, 192, 129, 8, 16, 48; 5, 0, 64, 144, 32, 0; 5, 0, 32, 96, 64, 0; 5, 0, 16, 0, 128, 0; 5, 0, 32, 0, 64, 0; 5, 0, 16, 0, 128, 0; 5, 0, 8, 1, 0, 0; 5, 0, 6, 6, 0, 0; 5, 0, 1, 104, 0, 0; 5, 0, 0, 144, 0, 0; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 108
Level Format EPL level; Parameter level: 0 = off 2 = on Function The EPL command switches the Ecoprint on or off (default). Ecoprint is a standard feature of the print systems that enables the user to reduce the amount of toner placed on the page which saves on printing costs. With EPL 2;, the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 109
None Function When the printing system receives the EXIT command, it exits from the PRESCRIBE mode and treats the following information as characters to be printed. If the parameter E is added (EXIT, E;), the printing system ignores one carriagereturn/linefeed immediately following the command. File - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 110
command is enabled only when the MP tray's operational mode is cassette or manual feed. Printing on A4 and letter size paper can only be done widthwise in first mode. This command causes a page break. This command is irrelevant to paper cassettes and envelope feeders. The paper orientation setting - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 111
area enclosed by the current path with the current drawing rule. It also fills all independent subpaths contained in a path. An open subpath is implicitly closed before being painted (as done by a CLSP command). This command clears the current path after filling and moves the cursor to the end of - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 112
PRESCRIBE Command Reference File !R! RES; UNIT C; SIMG 1; CMNT Drawing clusters; NEWP; PMZP 10, 12; PDRP -5.7, -1.75; PCRP 0, 0, 0, -3.4, 3.1, -3.6; CLSP; PAT 2; FILL; PMZP 10, 12; PDRP -2.6, -5.35; PCRP 0, 0, 2.5, -2.5, 4.9, .1; CLSP; PAT 3; FILL; PMZP 10, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 113
FILL Printout 103 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 114
computation. The number actually specifies the maximum error tolerance of a straight line segment approximation of any portion of the curve. The printing system resets the flatness to 1 when it receives the RES command. File !R! RES; FRPO N8,0; CMNT 300 dpi; UNIT C; SPD 0.02; NEWP; CMNT 1st circle - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 115
on each font such as font name, whether it is scalable or bitmap, font selection sequence using FSET, font ID, etc. The resident fonts are identified by the letter I (internal) in the font ID; the downloaded fonts are identified by the letter M or D depending on whether the font is stored in the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 116
PRESCRIBE Command Reference Sample of Font List Internal Scalable and Bitmapped Fonts List PRESCRIBE Font Name Scalable/Bitmap Password Selection [FSET] Font ID 106 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 117
only when the optional document finisher having the booklet stitcher is installed to the printing system. This command is most conveniently used sizes available for this mode include A4-R, letter-R, B4, A3 and ledger. The job is automatically delivered on the face-down output tray of the document - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 118
by the LDFC command or downloaded from the computer. If an match the attributes of the selected font. The scalable fonts, however, ignore the font mode setting. Line spacing must be specified by the user in this case using one of the line spacing commands (SLS, SLPI, etc.). File !R! RES; UNIT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 119
Printout Related Commands ALTF, FLST, SETF FONT 109 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 120
For printing system models that support 600/1200 dpi resolution printing, the default resolution generated by the FPAT command is 300 dpi; however, 600/1200 dpi can be selected using the FRPO B8 command. See Section 6.2. of the Technical Reference manual - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 121
File !R! RES; DAM; UNIT C; FSET 1p08V0s0b5T; MCRO PATTERN; FPAT %1, %2, %3, %4, %5, %6, %7, %8; BOX 5, 1; BLK 5, 1; MRP 0, 1.55; TEXT 'FPAT %1, %2, %3, %4, %5, %6, %7, %8;', L; ENDM; MAP 2, 2; SCP; CALL PATTERN, 3, 3, 0, 0, 0, 0, 0, 0; CALL PATTERN, 255, 0, 0, 0, 0, 0, 0, 0; CALL PATTERN, 1, 1, 1, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 122
sets the various printing parameters stored in permanent memory. Each parameter is identified by a code consisting of a letter and a numeral, such as P1. Details of the parameters and their values are given in Chapter 6 of the Technical Reference manual. The FRPO command should be used only when - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 123
Printout Related Command FRPO INIT FRPO 113 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 124
parameters. For a list of the factory default values, see Chapter 6 of the Technical Reference manual. The FRPO INIT command causes a page break. To activate the changes made with the FRPO INIT command, turn the printer power off then on again or reset the printer using the control panel keys. File - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 125
FSET FSET - change current Font SETting by characteristic Format FSET spacing-pitch-height-style-weight-typeface; Parameters spacing: fixed or proportional spacing, followed by a terminator P: 0 = fixed font 1 = proportional font pitch: pitch in cpi, from 0.44 to 99.99 cpi (ignored in a - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 126
= ITCZapfDingbats 45358 = SymbolPS The typeface values for option fonts, if installed, can be obtained by printing a font list. To print a font based on the characteristics of the font, the font's location in the printer, and the font's orientation. In the list below, the characteristics of font - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 127
fonts to match based on symbol set (the highest priority). All matches are next examined based on spacing. When the printer has reduced the matches to one measured in cpi and points respectively, regardless of the current unit setting (UNIT). Terminators following each parameter (P, H, V, S, B, and - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 128
PRESCRIBE Command Reference File !R! UNIT P; SFNT 'Swiss742SWC-Roman', 10; SLS 12; EXIT; First, this line is stroke weight are changed. !R! FSET 4101T; SLS 14; EXIT,E; The FSET 4101T; command switches the typeface to CGTimes. All other characteristics remain unchanged. !R! FSET 0P; FTMD 15; EXIT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 129
current font is changed by a FONT, ALTF, or RPF command, the printer automatically changes the designated attributes to the values of the new font. The default value of the FTMD command depends on the emulation mode. The printer does not automatically change any attributes not designated by the FTMD - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 130
Default Font Modes Emulation mode 0 (Line Printer) 1 (IBM X-24E) or 2 (Diablo 630) 5 (Epson LQ-850) 6 (HP LaserJet) 8 (KC-GL) Font mode 15 0 Printer adjusted at each font change, but line spacing and page orientation are left alone; UNIT C; SLS 1; BOX .5, -.5; MRP 1, 0; FONT 47; TEXT 'Font 47, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 131
Printout FTMD 121 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 132
resolution. For printer models that support 600/1200 dpi resolution printing, the default resolution generated by the GPAT command is 300 dpi; however, 600/1200 dpi can be selected using the FRPO B8 command. See Section 6.2. of the Technical Reference manual (FRPO B8). File !R! RES; UNIT C; MCRO - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 133
GPAT Printout Related Commands FPAT, PAT 123 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 134
-mode; Parameter gray-mode: 0 = represents gray in K (black, default corresponding area can be represented by using either the same quantity of toner or only K toner for each of CMY. (If C = M = Y, the graying process defaults to representation using K toner alone. However, a toggle switch is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 135
is ignored. Width and height specifications are dependent on the current unit of measurement (UNIT). If the output image has a specified width of 0, the and ENDG. If space is inserted, the command is ignored. When monochrome mode is specified, the output is printed as a grayscale image. File The - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 136
PRESCRIBE Command Reference c:¥> echo !R! STR 300; MZP 1,1; GRRD J,0,0; > lpt1 c:¥> copy /b fluit.jpg lpt1 c:¥> echo ;ENDG; PAGE; EXIT; > lpt1 Printout 126 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 137
for hue adjustment: 0 = all colors 1 = R 2 = Y 3 = G 4 = C 5 = B 6 = M angle: angle of hue rotation in degrees: color = 0, - 180 to 180 (default = 0) color = 1 - 6, -10 to 10 (default = 0) type: object type Function The HUE command shifts all the pixels around the 'color wheel' to a different - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 138
issued to rotate a particular hue when all hues are rotated, the hues are controlled after they are reset to their default state. The HUE command is enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other than NONE, the HUE is disabled. 128 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 139
manual, emulation by emulation. Depending on the current emulation, the printer selects one of the symbol sets of the emulated printer appropriate for the country as requested by the country-code value. For example, when the printer is set in the default emulation mode 6 (HP LaserJet), country code - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 140
default code-set value appears as the U7 parameter. The factory setting is 0. Symbol Sets Available with INTL Country-code 0 (Epson) Code-set (emulation) 1 (HP LaserJet)a 2 (Daisywheel) 4 (IBM/Line Printer current symbol set. (Default is US ASCII). It does not fully support all of the HP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 141
INTL File !R! CMNT This file will not print correctly in the IBM; CMNT emulation (mode 1); RES; INTL 2, 2; SLM 1; STM 2; SFNT "Helvetica", 14; EXIT; Diese [pfel sind eine ]berraschung! !R! PAGE; EXIT; Printout 131 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 142
virtual mailbox specified by mailbox-id 15 = Resets all virtual mailboxes to a clean state job-id or mailbox-id: an integer or character string that specifies the job ID or mailbox ID 0 = for modes 8, 9, and 15 only, affects all the mailboxes 1 to 255 = tray ID (specified by JOBS) Character string - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 143
with an ID of 28L016T50 from the hard disk: !R! JOBD 1, "28L016T50"; EXIT; To delete all permanent jobs in the hard disk: !R! JOBD 2; EXIT; To delete all temporary and permanent jobs in the hard disk: !R! JOBD; EXIT; To delete the jobs stacked in virtual mailbox number 3, which has the password of - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 144
PRESCRIBE Command Reference JOBL - print JOB List Format JOBL mode; Parameter mode: 1 = prints a list of temporary jobs in the virtual mailboxes containing jobs which caused an error during data is written to the mailbox. An error log indicating failure is also printed when jobs within such - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 145
File To print a permanent job list: !R! JOBL 2; EXIT; JOBL 135 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 146
Reference JOBO - JOB Output Format JOBO mode, 'job-id' or 'mailbox-id'[, password]; Parameters mode: 0 = normal 8 = virtual mailbox job-id (mode 0): job ID or page ID mailbox-id (mode 8): mailbox ID from 1 to 255, or alias password (mode 8 only): password for the mailbox Function The JOBO - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 147
which a password is set. An error will be displayed on the operator panel if no password or an incorrect password is specified. An error will result and jobs in the virtual mailbox can be printed. To output the job with job ID 4H90058I0 in the hard disk, with no barcode printed, in 7 copies: !R! JOBP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 148
binding 2 = short edge binding JOBO 1 = face-down 2 = face-up 3 = finisher tray JOBO 0 = off 1 = bottom left, angled 2 = top left, automatic angled or upright 3 = two centered JOBO 0 to 7 or 128 to 135 (printing page ID's) M or m = staples the maximum number of sheets. For example, 20 sheets - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 149
if the preceding job to print was assigned by JOBS. A JOBP command sequence is cancelled if the host interface of the printing system is switched from one to another after the timer has expired for the interface. Files To print the print job 'monthlyreport,' disabling the original barcode printing - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 150
of copies to print: 1 to 999 barcode (starting-mailbox when save-mode is 8): a number representing the page(s) barcode is printed1: 0 = On cover page only 1 = On whole pages 2 = None barcode-position (ending-mailbox when save-mode is 8): a number representing the position of barcode: 0 to 7 or 128 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 151
Files below on page 144. Among the e-MPS finishing functions, not all of them require a mode, the printing system indicates 'harddisk error 97' meaning that no more permanent jobs are storable. The printing system forcibly uses save-mode 0. With mode 0, 1, or 2, it is possible to print a barcode ID - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 152
error will be displayed. While jobs are being stacked on a virtual mailbox, a message indicating that jobs are being stacked on virtual mailboxes (when the VMB-compatible printer driver is saved in permanent mode. !R! JOBS 2,3,2,2,0,'Beauty- ', '01/14/02 16:30:25'; UNIT C; MZP 5, 10; BOX 6, 6; PAGE - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 153
JOBS !R! JOBS 8, 3, 3, 15, 0, 'Service', 'Repair', '01/14/02 16:30:25'; UNIT C; MZP 5, 10; BOX 6, 6; PAGE; TEXT 'ABCDE'; PAGE; TEXT 'Domestic'; PAGE; JOBT; EXIT; 143 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 154
in the cyclic manner. At execution, the JOBT command starts printing the job including stapling, job separation, job offset (if the relevant option device is installed). File The file below sorts and prints the defined job in 40 copies. The pages between JOBS and JOBT are output to virtual mailbox - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 155
of a command such as RES, FRPO and SEM which results in a reset of the printer. When JOG is issued with a job defined by JOBS and JOBT, function and deliver printed pages to the face-down tray of the optional stacker in offset mode or separation mode. (A barcode is output on the first page only - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 156
PRESCRIBE Command Reference LAPI - LoaD API Program Format LAPI Program type, PRESCRIBE command, function name; Parameters Program type: Type of the downloading program "PRE" PRESCRIBE command PRESCRIBE command name: Name of the PRESCRIBE command to be stored Alphanumeric string of 2 to 4 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 157
LDFC - LoaD Font Character Format LDFC font-number, code, height, code of the character (0 to 255) height: height of the character bitmap, in dots (integer from 0 to 3999) width: width of the character bitmap, in dots (integer from 0 to 3999) y-offset: distance from the baseline to the top - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 158
such as the one shown below, which is defined as the '+' symbol (character code 43) of font 1000. Details and another example appear in Chapter 4 of the Technical Reference manual. The resolution is valid only on a 600/1200 dpi printer model. File !R! LDFC 1000, 43, 39, 29, 1216, 0, 1216, 608 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 159
LDFN C LDFN C - generate bitmap character for LoaDing FoNt Format LDFN C, font-number, code, height, width, y-offset, x-offset, cell-width; bit-map; Parameters font-number: font number (integer from 1000 to 65535) code: ASCII code of the character code (0 to 255 for European; 0 to 65533 for - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 160
downloaded font header already defined using LDFN F. Note that each character code defined must match the font number, symbol set (1- or 2-byte code), and other information of the font header already created. The bitmap data transferred at the end of this command is transferred under Kyocera error - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 161
: 0 = 300-dpi bitmap 1 = 600-dpi bitmap 3 = 1200-dpi bitmap (Fine mode) name: font name (ASCII text string up to 31 characters long). This string must be enclosed in either single or double quotation marks. symbol-set: symbol set: numeric value = 1-byte code symbol set (1 to 65535 [619: Shift JIS - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 162
codes from 32 to 127 1 = character codes from 32 to 127 and from 160 to 255 2 = character codes from 0 to 255 Function The LDFN F command creates a font header for downloading a font to the printer byte code) emulation Japanese character (2-byte code) emulation (linked using ASFN) A command error - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 163
S LDFN S - LoaD truetype FoNt Format LDFN are two font headers for Japanese TrueType fonts, the printer automatically creates a font number increased by 1. name: symbol-set: font symbol set value: 1 to 65535 (619 = Shift JIS code) style: font style: 0 to 32767 stroke: stroke weight: -127 to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 164
to be downloaded to the printing system. A binary format is used to represent font data. The size of this data must match that given by parameters are outside the given range. This command is ignored if even one parameter error occurs. Although symbol-set, style, stroke and type-face may be omitted, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 165
The gamma and contrast can be set independently of each other. In gamma control mode, the color bars below represent the lightness gamma variation using hue R as an example. The top color bar represents the default lightness variation (γ = 1.0) with its median indicated by the symbol. The left side - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 166
enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other than none, this command is disabled. This mode is not held permanently in the printing system. For this reason, saturation is reset to its default state when the power is turned on. 156 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 167
specified relative to the top and left margins, measured in the units designated by the UNIT command. The coordinates may coordinates move the cursor outside the margin. The MAP command is ignored in path mode graphics. File !R! RES; UNIT C; STM 2; SLM 2; SFNT 'Helvetica-Nr', 9; MAP 0, 0; BOX 40 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 168
PRESCRIBE Command Reference Printout Related Commands MRP, MZP, MRPA 158 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 169
the various conditions of emulation, paper type, and print quality. In monochrome mode, color matching is defaulted to 0 (none). Mode 0 does not perform color matching. Mode 1 automatically selects color correction mode depending on the printing data. Text or vector graphics data are processed using - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 170
character string starting with a letter dummy-sign: any character (default: % preceded by a space) comment: any character string switching power off. See the Technical Reference manual for information on the limitations about the usage of macros. The PCL5E command language, available in the mode - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 171
- important if resource protection mode is used. See also Resource Protection in the Technical Reference manual. Macro Downloaded Memory card Internal Location RAM Memory card ROM Property Temporary/Permanent Permanent Permanent The internal printer firmware manages the PCL macros, recognizing - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 172
ATtribute Format MDAT [media-type[, paper-weight, fuser-mode, duplex[, density]]]; Parameters media-type 1 = Plain 2 = Transparency 3 = Preprinted 4 = Label 5 = Bond 6 = Recycled 7 = Vellum 8 = Rough 9 = Letterhead 10 = Color 11 = Prepunched 12 = Envelope 13 = Cardstock 14 = Coated 15 = Second - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 173
whether the paper with that paper type is allowed for duplex printing or not. If the parameters paper-weight and fuser-mode are omitted, this command resets the three attributes back to their defaults. If all the parameter are omitted (MDAT;), all the attributes for the all media types are - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 174
the beginning of a file or program, or at the top of a new page. The selection of a tray group made by the MID command is effective until it is changed by another MID command (It is not reset by the RES command). If the printer receives an ASTK command or one of the FRPO commands - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 175
MPSS MPSS - e-MPS Storage Format MPSS 'job-type', 'limit', size; Parameters job-type: CODE = temporary or permanent job VMB = virtual number from 0 to 9999 in unit of megabytes number from 1 to 50 for QUICKLIMITCOUNT Function The MPSS command is used to allocate the limit values for the storage - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 176
is shown when the MP tray becomes empty. Mode 1 (default) enables the paper-empty message to display when the MP tray is empty. When Mode is 0, this message is disabled despite the MP tray is empty and the other paper source(s) is not empty. (showing Ready, for example). It is not reset by the RES - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 177
the cursor from its current position to a specified relative position, measured in the units designated by the UNIT command. The coordinates may be positive or negative. The MRP command works in the standard mode graphics only. To move to a relative position in a path construction, use the PMRP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 178
PRESCRIBE Command Reference Printout Related Commands MAP, MZP, MRPA 168 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 179
from its current position across a specified distance using a specified angle. The distance is measured in the units designated by the UNIT command. The MRPA command is ignored in the path mode graphics. To move to a relative position specifying angle in a path construction, use the PMRA (in Path - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 180
PRESCRIBE Command Reference Printout Related Commands MAP, MRP, MZP 170 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 181
is valid only when the option sorter is installed with the printing system. It instructs the printing system to deliver printed pages in the mailbox mode. In the mailbox mode, the printed pages are delivered to the trays in the reverse order of tray parameters. The printed pages are delivered first - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 182
, the printing system looks for the paper source which has the matching media type. To assign a paper type to the paper cassette, use the operator panel or the FRPO X0 - X7 commands. For the MTYP command to work, the automatic cassette switching mode must be set to on in the printing system. To do - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 183
MTYP File To print on the A4 label loaded on the printer's MP tray, set the MP tray size to A4 and the MP tray type to Labels (See the user's manual for details.) !R! RES; PSRC 100; CMNT Sets the printer to automatic casette mode; CMNT Depending on the current media type; SPSZ 8; MTYP 4; CMNT Paper - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 184
relative to the top and left edge limits of the paper, measured in the units designated by the UNIT command. The coordinates path mode graphics. To move to a zero-relative position in a path construction, use the PMZP (in Path, Move to Zero-relative Position) command. File !R! RES; UNIT C; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 185
MZP Printout Related Commands MAP, MRP, MRPA 175 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 186
line along it (STRK, FILL). For a full description of path, refer to Chapter 1 of the Technical Reference manual. File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 1, -2, 3, 0, -1, 2, -3, 0; STRK; CMNT Stroking the path; NEWP; PMZP 10, 5; PDRP 1, -2, 3, 0, -1, 2, -3, 0; GPAT .5; FILL 1; CMNT Filling the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 187
. If an optional device such as a stacker, a document finisher, or a sorter is installed, the tray value 2 instructs the printing system to deliver printed pages to its face-up tray; the value 3 delivers the pages to its face-down tray. The tray values of 5, 7, 11, 12, 13, 14, 21, 22, 31, 32, 41, 42 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 188
delivered face-down as usual, page 1 first. !R! PAGE; EXIT; PAGE 2 PAGE 2 next, and so on, stacking in the correct order. !R! PAGE; EXIT; PAGE 3 But on printers with two paper trays this file will be delivered to the face-up tray with the pages in reverse order, page 3 on top. !R! PAGE; EXIT; 178 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 189
PAGE PAGE - start new PAGE Format PAGE; Parameter None Function The PAGE command causes a page break without resetting the printer. Subsequent data will be printed on a new page with no changes made to page formatting parameters such as spacing, margins, font selection. If there is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 190
selected. The color is always assigned to index number 0. Colors may be added to the palette or changed. However, when a color is assigned to command. The colors corresponding to previously entered commands are deleted. The palette ID number remains valid (active) and does not change. A total of 45 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 191
4 Warm Gray 4 Warm Gray 8 Cool Gray 4 Cool Gray 8 The PANT command may not work with certain printer models and versions. Set the print quality to Quick mode when this command is used with model FS-5800C. PANTONE colors cannot be used by the PANT command in KPDL emulations. !R! PANT 'Cool Gray - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 192
coordinates of the center of arc, measured from the left and top edge limits radius: radius of arc start-angle: starting angle, to the current path. Coordinates and radius are measured in the units designated by the UNIT command; the starting and ending angles are measured counterclockwise from the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 193
PARC Printout 183 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 194
through 60 if a resident pattern is selected. A full list of the printer's resident patterns appear on the following page. Pattern numbers 100 through 105 patterns are defined, the printer selects the No. 1 (solid black) resident pattern. Variable resolution support is valid for 600 dpi and 1200 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 195
PAT Resident Fill Patterns (300 dpi) 185 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 196
PRESCRIBE Command Reference PCRP - in Path, Curve to Relative Position Format PCRP x1, y1, x2, y2, x3, y3; Parameters x1, y1: coordinates of the first control point as measured from the current cursor position x2, y2: coordinates of the second control point as measured from the current - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 197
File !R! RES; UNIT C; NEWP; SPD .1; PMZP 3, 3; PCRP 4, 2, 5, 1.5, 6, 1.8; STRK; PAGE; EXIT; Printout Current positon (5, 1.5) (4, 2) (6, 1.8) File !R! RES; UNIT C; NEWP; SPD .1; PMZP 3, 3; PCRP 5.5, 1.5, 1.5, 5.5, 7, 7; STRK; PAGE; EXIT; Printout Current positon (5.5, 1.5) PCRP (1.5, 5.5) - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 198
limits of paper x2, y2: coordinates of second control point as measured from the left and top edge limits of paper x3, y3: coordinates of end point as measured from the left and top edge limits of paper Function The PCZP command adds a Bézier curve segment to the path, starting from the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 199
File !R! RES; UNIT C; PMZP 3, 6; PCZP 11, 3, 2, 2, 9, 6; STRK; PAGE; EXIT; Printout (2, 2) PCZP (11, 3) (9, 6) Current position (3, 6) 189 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 200
orientation and does not affect the current page orientation. A bitmap font prints text according to the current page orientation (it adheres to the current font mode). The PDIR command does not cause a page break, so you can print text in four different directions on the same page as shown in the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 201
Portrait (PDIR 0;) Landscape (PDIR 90;) PDIR Reverse Landscape (PDIR 270;) Reverse Portrait (PDIR 180;) File !R! RES; UNIT P; SFNT 'Helvetica', 8; UNIT C; MZP 10, 12; SPD .144; CIR .075; PDIR 270; TEXT ' ENDLESS VARIETY AND VERSATILITY'; PDIR 180; TEXT ' ENDLESS VARIETY AND VERSATILITY'; PDIR - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 202
PRESCRIBE Command Reference Printout 192 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 203
by the SPD command. Multiple pairs of coordinates may be specified. The printer then draws a connected series of line segments, proceeding from one point to the next. For example, PDRP 1, 2, 3, 4; is equivalent to PDRP 1, 2; PDRP 3, 4;. File !R! UNIT C; SPD .3; CMNT Cube; NEWP; PMZP 5, 15; PDRP - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 204
PRESCRIBE Command Reference Printout Related Command PDZP 194 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 205
a line to the current path from the current cursor position to a position specified relative to the top and left edge limits of the current page, measured in the units designated by the UNIT command. The cursor moves to the specified coordinates. The coordinates may be positive or negative. Negative - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 206
PRESCRIBE Command Reference Printout Related Command PDRP 196 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 207
. In addition, STRK or FILL is required. A complete ellipse path will be defined if the parameters in brackets are omitted. Executing this command will close current sub-paths. An error will result and the command has no effect if the bounding box is specified as a straight line or a point. 197 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 208
Command Reference Current cursor position (x-end, y-end) (x-start, y-start) Bounding box (x-diagonal, y-diagonal) N : C : P : File !R! RES; UNIT C; MZP 0, 0; BOX 2, 3; NEWP; PMZP 0, 0; PELP 2, 3, 2, 0, 0, 0, N; STRK; MZP 5, 5; BOX 2, -3; NEWP; PMZP 5, 5; PELP 2, -3, 2, 0, 0, 0, N; STRK; MZP 10 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 209
of the slices Function The PIE command is a standard mode graphics command which draws a pie chart centered at the the command must not exceed 255 characters. The printer automatically converts the slice sizes to angles totaling 360 File !R! RES; UNIT C; MZP 10, 10; PIE 3, 0, 10, 20, 30, 40; PAGE - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 210
PRESCRIBE Command Reference Printout 200 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 211
be noted that the x and y coordinates are measured from the top and left edge limits of the page, and not from the current cursor position. The coordinates and distance are measured in the units designated by the UNIT command. The angle is measured counterclockwise from the positive x axis. New - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 212
PRESCRIBE Command Reference File !R! RES; UNIT C; SPD 0.2; NEWP; PMRA 10, 19, 5, 45; PARC 10, 19, 5, 45, 135; STRK; PAGE; EXIT; Printout 202 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 213
a specified relative position in a path construction, measured in the unit value designated by the UNIT command. The coordinates may be positive or negative. File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 5, 0, 0, 5, -5, 0, 0, -5; GPAT .2; FILL 1; PMRP 4, 4; PDRP 5, 0, 0, 5, -5, 0, 0, -5; GPAT .8; FILL - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 214
PRESCRIBE Command Reference Printout Related Command PMZP 204 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 215
The PMZP command moves the cursor to a position in a path construction, specified relative to the top and left edge limits of the current page, and measured in the units designated by the UNIT command. The coordinates may be positive or negative. Negative coordinates move the cursor off the current - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 216
PRESCRIBE Command Reference Printout Related Command PMRP 206 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 217
62 = 4 (Europe) or 2 (U.S.), right 71 = 2 (Europe) or 3 (U.S.), top 72 = 4 (Europe) or 2 (U.S.), top Function The PNCH command lets the option finisher perform punching through the printed page with the number of holes depending on the country. mode selects either the standard or additional number - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 218
top sides of the page by logically aligning the page in reference to the punched holes. Note that the mode parameter is valid for a finisher with the dual mode punching system, such as the DF-71, only. It becomes invalid if it is specified in a finisher with the standard punch unit not switched - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 219
height: height of round box radius: radius of round box corners Function The PRBX command adds a round box path to the current path. This command close the sub-paths but does not stroke the path by itself. Therefore, STRK or FILL is required to follow this command. The parameter value for - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 220
PRESCRIBE Command Reference File !R! RES; UNIT C; SPD 0.125; NEWP; PMZP 1, 1; PRBX 11.7, 1.7, 0.5; STRK; MZP 1.5, 2.15; SFNT "Helvetica-Bd", 24; TEXT "CAUTION: HOT SURFACE!"; PAT 5; NEWP; PMZP 1, 4; PRBX 5, 2.4, 0.3; FILL; MZP 1.4, 4.7; SFNT "Helvetica- - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 221
to the current position, then adds the line and the arc to the current path. Coordinates and radius are measured in the units designated by the UNIT command; the starting and ending angles are measured counterclockwise from the positive x axis. For example, the following example draws an arc - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 222
PRESCRIBE Command Reference PRRC 1, 1, 180, 0; Negative values are acceptable for angle. For example, an angle of 315 degrees is the same as -45 degrees. File !R! RES; SPD 0.05; MZP 4.5, 5; NEWP; PRRC -1, 0, 1, 90, 270; PRRC 1, -2, 1, 0, 180; PRRC 2, 1, 1, -90, 90; PRRC -1, 2, 1, 180, 0; STRK; PAGE; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 223
beginning of a file or program, or at the top of a new page. The current paper source will remain selected if the specified cassette is not installed. File !R! RES; UNIT C; SFNT "Helvetica-Nr", 24; PSRC 1; TEXT "This page is fed from the default cassette."; PAGE; PSRC 0; TEXT "This page is fed from - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 224
intersection is default to HP PCL; and grid centered mode is used by Microsoft Windows. This command is ignored when used with DAP, DRP, DRPA, DZP, BOX, BLK, CIR, ARC, or PIE. This command has no effect for text or images. The printing system is reset to grid intersection mode by the RES command - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 225
manual. If !R! is used by mistake when the printer is already in the PRESCRIBE mode, the printer ignores the mistaken !R! and whatever follows, up to the next semicolon. File !R! SFNT 'Helvetica', 14; EXIT; Following these five lines, the printer enters PRESCRIBE mode to execute commands. !R! UNIT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 226
PRESCRIBE Command Reference Printout Related Commands EXIT, SCRC 216 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 227
instructs the printing system to stack the sets on the tray in alternating orientations. The RCLT command require a hard disk installed paper must be loaded into two separate cassettes. For example, Portrait (A4) and Landscape (A4-R) would be used when printing onto A4 paper. The MP tray can also be - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 228
PRESCRIBE Command Reference RDMP - Received-data DuMP Format RDMP; Parameter None Function The RDMP command causes all subsequent data to be printed in hexadecimal form (two hexadecimal digits per character) until an ENDD (END Dump) command is received, or until the printing system runs out of data - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 229
Sample RDMP 219 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 230
emulation, the RES command resets the printer environment in the same manner as the KC-GL DF instruction. Refer to section HP 7550A Emulation [KC-GL] (Mode 8) of the Technical Reference manual. The RES command does not: • delete permanent macros or permanent fonts from memory • delete positions or - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 231
RES Parameter Value after reset (Related FRPO parameter) LaserJet (PCL) IBM SFNT font)a Alternate font assignment None See Emulation of ← the Technical Reference manual. SETF Country code 0 (U6)† ← ← INTL Symbol set Roman-8 (U6/7) See Emulation with a parameter of 1 (default). 221 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 232
there is insufficient memory because a duplex unit is installed and duplex mode has been set or because the video memory size has been increased for page protection. Printing resolution cannot be switched from 300 dpi to higher resolutions for the following emulations: line printer, IBM ProPrinter - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 233
RGB. The top bar represents the default saturation variation. Default color balance (G) Color balance increased Color balance decreased Default color balance (B) Color balance increased Color balance decreased Varying color balance allows the output image results to vary. Issuing this command resets - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 234
Reference This command is enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other than none, this command is disabled. The RES command resets saturation to its default state. This mode is not held in the printing system. For this reason - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 235
unit. current unit. The mode. Since this command is PCL command-compatible (&l #U, & l #Z), the offset values are cleared to zero only by a software reset (E). In other words, the offset is only cleared by PRESCRIBE (RES and FRPO INIT commands) when the emulation is HP. An error - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 236
PRESCRIBE Command Reference RPCS - Return to Previous Code Set Format RPCS; Parameter None Function The RPCS command resumes use of a code set saved by a previous SCCS (save current code set) command. The RPCS commands return to the code sets in reverse order in which they were nested. File See SCCS - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 237
commands return to the fonts in the reverse order in which they were saved. SCF and RPF are particularly useful in macros. File !R! RES; UNIT P; MCRO SMALLPRINT; SCF; FSET 10V; TEXT %1, E; RPF; ENDM; SFNT 'Helvetica', 12; SLS 14; EXIT; Computer literature is littered with acronyms such as !R! CALL - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 238
is shown below. The RPG command does not affect other printing system parameters such as page orientation, unit of measurement, etc. (See RES on page 220.) File !R! RES; UNIT C; NEWP; PMZP 4, 2; PARC 3, 3, 1, 90, 270; PARC 5, 3, 1, 270, 90; CLSP; SCG; CMNT Saves the graphics state; STRK; CMNT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 239
RPG Printout Related Command SCG 229 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 240
been saved, the resulting cursor movement is unpredictable. The RPP command can be used in both standard mode and path mode graphics. File !R! RES; UNIT P; SFNT 'Helvetica-BdOb', 16; UNIT C; MAP 8, 8; CIR .2; MRP -.1, .1; CMNT Save this position seven times; SCP; SCP; SCP; SCP; SCP; SCP; SCP; MRPA - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 241
RPP Printout Related Command SCP 231 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 242
PRESCRIBE Command Reference RPPL - Return to Previous PaLette COLOR Format RPPL; Parameter None Function The RPPL command restores the color palette most recently saved by a SCPL (save current palette) command. A color palette restored using the RPPL command immediately becomes active. If the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 243
RPU RPU - Return to Previous Unit Format RPU; Parameter None Function The RPU command brings the unit of measurement (inches, centimeters, points, or dots; as specified by the UNIT command) back to the unit saved by the SCU (save current unit) command. File/Printout See SCU on page 283. Related - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 244
PRESCRIBE Command Reference RTTX - RoTate TeXt Format RTTX angle, 'string'[, U-option]; Parameters angle: angle of rotation in degrees string: character string U-option: Underline text Function Taking the normal output angle for text as zero, the RTTX command rotates a character string - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 245
RTTX Printout 235 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 246
margins. The length of the string is unlimited, except that the command as a whole may not be longer than 255 characters. Carriage-return and linefeed codes in the string are ignored. The RTXT command can be used both in the standard - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 247
File !R! RES; UNIT P; SFNT 'TimesNewRoman'; UNIT I; MCRO PF; MRP .15, 0; BOX .1, -.1; MRP .5, 0; BOX .1, -.1; MRP -.65, 0; ENDM; MAP 3, 3; TEXT 'Pass Fail', L, U; CALL PF; RTXT 'Unit test', L; CALL PF; RTXT 'Integration test', L; PAGE; EXIT; Printout RTXT 237 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 248
cursor position. The SRO (Set Raster Options) command specifies the orientation of the raster image in either physical (default) or logical page direction. If the compression-mode value is zero [or omitted], the printing system simply transfers raster data in an uncompressed binary format. A single - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 249
CoLor raster data COLOR Format RVCL [compression-mode,] length, data; Parameters compression-mode: 0 = uncompressed (Default) 1 = run-length encoded 2 = TIFF encoding, since it relies on the active palette, the correct palette matching the print data must be used. The end of raster data must - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 250
PRESCRIBE Command Reference RVRD - ReceiVe Raster Data Format RVRD; number of data, data, ... ; Function The RVRD command declares the start of raster data. Raster data represents dot lines encoded as numeric values as shown below. Each dot line is divided into 8-dot segments. Each segment is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 251
which follows. The subsequent data can be obtained by following the same procedure as explained in Defining Fill Patterns in Chapter 2 of the Technical Reference manual. 241 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 252
Function The RWER D command deletes data on any external media whether it is a memory card or the hard disk. This command has no effect if the media has was enabled (by the RWER I command). ( See page 244.) A command error results and the command has no effect if parameters other than the above are - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 253
RWER F command formats any external media whether it is a memory card or the hard disk. The hard disk is physically formatted when it is specified. This command has no effect if the media has been write-protected using KPDL or PJL. A command error results and the command has no effect if parameters - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 254
is a memory card or the hard disk. With the automatic printing of partition lists enabled (RWER I, E;), the printing system prints partition lists whenever data are written to external media. The setting made with this command returns to default when the power is turned off. A command error results - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 255
RWER L command explicitly prints partition lists for any external media whether it is a memory card, the hard disk, or the RAM disk. The lists of partitions for file data output in separate columns. A command error results and the command has no effect if parameters other than the above are used. - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 256
partition from which data is read, a maximum of 15 printable ASCII characters Function The RWER R command reads data from any external media whether it is a memory card, hard disk, EPROM, or RAM disk. Only data types 2 and 128 are allowed. Note that reading data of other data types, such as fonts - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 257
drive specification: 0 = hard disk or RAM disk A = memory card font-type: font type: 0 = TrueType font 1 of up to 11 characters; the extension .INF is added internally.) This string must be enclosed in either single or to 65535, 619: Shift JIS code) style: font style (0 to 32767) weight: stroke weight (- - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 258
downloaded to the printing system and to be stored on the specified media as font data. TrueType fonts particularly can be defined easily just by adding one parameter error occurs. The font data following the semicolon for this command must match the length given by length. An error will result and - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 259
RWER T command sets a terminator string for external media whether it is a memory card or the hard disk. This terminator is used when storing binary data ) for example. WRED is set as the default terminator if parameter terminator is omitted. A command error results and the command has no effect if - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 260
The RWER W command writes data to any external media whether it is a memory card or the hard disk. Although all data types may be written up A partition list will be printed as a warning when this happens. A command error results and the command has no effect if parameters other than the above are - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 261
display has changed to Waiting, and then send a WRED command, as follows: C:\>ECHO WRED; EXIT, E; >PRN The WRED command terminates writing to the memory card. Note that in W mode the ICCD command is accompanied by a form feed. If a partition name conflict occurs when writing a new partition to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 262
Reference RWRF D - [Read/Write Resource File] Delete data on external device Format RWRF D, medium, data-type, "file-name"; Parameters medium: 0 = hard disk A = memory card data-type: "API" API program "FNT" Font data "MCR" Macro data "PRN" Printable data file-name: ASCII text string up to 15 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 263
RWRF F RWRF F - [Read/Write Resource File] Format external device Format RWRF F, medium; Parameters medium: 0 = hard disk A = memory card Function The RWRF F command physically and logically formats an external device such as the hard disk. This command has no effect if the target - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 264
PRESCRIBE Command Reference RWRF L - [Read/Write Resource File] print resource file List Format RWRF L[, 'medium']; Parameters medium: 0 = hard disk A = memory card Prints a resource file list for all devices if omitted. Function The RWRF L command prints a resource file list registered in an - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 265
RWRF P RWRF P - [Read/Write Resource File] set hidden file Format RWRF P, medium, data-type, "file-name"; Parameters medium: 0 = hard disk A = memory card data-type: "API" API program "FNT" Font data "MCR" Macro data file-name: ASCII text string up to 15 bytes. Function The RWRF P command - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 266
. The data must be a printable data. When the file name is coexistent in both the hard disk and memory card that are installed in the printing system, the printing system will read the memory card first, then the hard disk. The partition name may be a maximum of 15 printable ASCII characters (20H - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 267
terminator: ASCII text string up to 4 bytes Set to default "WRED" if omitted. Function The RWRF T command changes a terminator (default: WRED). The terminator that was changed with this command is also available for the LAPI command to load the API program. Turning the power on again will return - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 268
Format RWRF W, medium, "API", "program-type", prescribe-command-name, APIprogram-start-function-name, "file-name"; Parameters medium: 0 = hard disk A = memory card program-type: "PRE" prescribe command prescribe-command-name: ASCII text string up to 4 bytes API-program-start-function-name: ASCII - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 269
font-style, stroke-weight, typeface; Parameters medium: 0 = hard disk A = memory card font-type: 0 = TrueType Font 1 = Japanese TrueType Font 2 = Japanese Number of bytes in font data to be downloaded symbol-set-value: 1 to 65535 (619 = Shift JIS code) font-style: 0 to 32767 stroke-weight: -127 to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 270
should not omit those font attributes to exactly select a font. The length of the font data to be written must match the specified one. Failure to do so will result in an error, and disables you to write data. Specify WRED; command following . "WRED;" (five bytes) are not included in - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 271
to external device (macro) Format RWRF W, medium, "MCR", macro-type, "macro-ID or macro-name", "filename"; Parameters medium: 0 = hard disk A = memory card macro-type: "PRE" prescribe macro "PCL" PCL macro macro-ID or macro-name: macro-ID for PCL macro (0 to 32767) macro-name for prescribe macro - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 272
[Read/Write Resource File] Write data to external device (printable data) Format RWRF W, medium, "PRN", "file name"; Parameters medium: 0 = hard disk A = memory card file-name: ASCII text string up to 15 bytes Automatically set by the system if omitted. Function The RWRF W command writes data to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 273
as an example. The top color bar represents the default saturation variation. The symbol modes and all monitor simulation modes. If ink simulation is set to other than None, this command is disabled. This mode is not held in the printing system. For this reason, saturation is reset to its default - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 274
and SLPP (set lines per page) commands also set the bottom margin, but these commands measure from the top margin position. File !R! RES; UNIT C; STM 1; SLS 1; SBM 11; SFNT 'Helvetica-Nr'; EXIT, E; Top margin at 1 cm, bottom margin at 11 cm. (Line 1) Line 2 Line 3 Line 4 Line 5 Line 6 Line 7 Line - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 275
SBM Printout 265 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 276
mode; Parameter mode: line cap mode: 1 = square caps 2 = butt caps 3 = round caps Function The SCAP command determines the shape of line ends (or a line cap) in a path where they are finally stroked. The default width. Square caps (default) Butt caps Round caps File !R! UNIT C; SPD .5; NEWP; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 277
SCAP Printout 267 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 278
SCCS; Parameter None Function The SCCS command instructs the printing system to remember the code set of the current font. This command may be used in conjunction with a SCF (save current font) command to prevent the font from losing the current code set after a command operation has been made - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 279
SCCS Printout Related Commands RPCS, RPF, SCF 269 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 280
can be either a bitmap font or a scalable font. Up to eight font numbers can be saved in the printing system's memory by SCF commands (using a separate SCF command for each). The SCF command only instructs the printing system to remember the font. It does not move actual fonts in or out of - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 281
SCF Printout Related Command RPF 271 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 282
path. The printing system holds as much graphics state information as the user memory area can accommodate; however, graphics state information larger than the memory area can cause a memory error. File !R! RES; UNIT C; NEWP; PMZP 5, 5; SFNT 'Helvetica-Bd', 72; CPTH 'Mary'; SCG; STRK; RPG; GPAT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 283
SCG Printout Related Commands FILL, RPG 273 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 284
PRESCRIBE Command Reference SCOL - Select COLor COLOR Format SCOL number; Parameter number: number from 0 to 255 (Default is 0.) Function The SCOL command selects a color from the currently active palette. If no color is assigned to the specified number, this command is ignored. - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 285
; Parameter None Function The SCP command instructs the printing system to remember the current cursor position, so that it can be retrieved later using the RPP (return to previous position) command. Up to eight positions can be saved in the printing system's memory (using a separate SCP command for - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 286
of characters per inch Function The SCPI command sets the number of characters per inch (even if the UNIT command designates a non-inch unit). When a proportionally-spaced font is used and the font mode (FTMD) is 0 to 3 or 8 to 11, SCPI 0 (zero) must be specified to obtain the innate spacing of - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 287
SCPI Printout Related Command SCS 277 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 288
. If there is insufficient memory, a memory overflow will result and the palette will not be saved. This command does not change the active palette. RPPL commands return to the saved palettes in the reverse order in which they were saved. File !R! RES; SEM 6; UNIT C; SFNT 'Incised901SWC-Black', 20 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 289
code 126 (~) except the apostrophe ('), quotation mark (") or semicolon (;). Function The SCRC command changes the command recognition character between the exclamation points in the PRESCRIBE start sequence. The change remains in effect until power is turned off or a RES (reset RES; UNIT C; GPAT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 290
PRESCRIBE Command Reference Printout 280 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 291
beginning of the next character. When a proportionally-spaced font is used and the font mode (FTMD) is 0 to 3 or 8 to 11, SCS 0 (zero) must command. File !R! RES; SLM 1; STM 2; EXIT; This line has the default spacing. !R! UNIT C; SCS .3; EXIT; This line has a slightly wider spacing. !R! SFNT ' - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 292
command causes a page break, so it should be placed at the top of a file or program, or at the beginning of a new page. This command uses the unit set in the unit parameter of this command, regardless of the unit set in the UNIT command. The setting made with this command provides a non-printing - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 293
Format SCU; Parameter None Function The SCU command instructs the printing system to save the current unit of measurement. Saving the current unit can prove useful when a macro containing a UNIT command changes the unit of measurement. The saved unit can be retrieved later using the RPU (return to - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 294
PRESCRIBE Command Reference Printout Related commands SCF, SCP, UNIT 284 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 295
of alternating black and white segments for stroking the line segment in the path, using the unit value designated by the UNIT command. For example, SDP 11, 2, 2, 5, 5; stores the following dash pattern in command changes the current definition or until the printing system is switched off. 285 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 296
PRESCRIBE Command Reference File !R! RES; UNIT P; SDP 11, 2, 2, 5, 5; NEWP; UNIT C; SPD .2; PMRA 10, 10, 3, 0; DPAT 11; PARC 10, 10, 3, 0, 360; STRK; PAGE; EXIT; Printout Related Command DPAT 286 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 297
beginning of a program or file. The SEM command does not change the power-up emulation mode. When power is switched off, the printing system loses the mode set by the SEM command. Upon power up, it retains the default emulation, which is set by the P1 parameter of the FRPO command. If you usually - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 298
nonresident font defined by LDFC (load font character) commands. A In some emulation modes, default assignments are given to low alternate numbers so that SETF commands can be embedded for some word processing software. See Emulation of the Technical Reference manual - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 299
SETF Printout 289 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 300
spacing F/P: F = fixed spacing P = proportional spacing Non-executable Parameters rotation: 0 = normal 1 = face-down 2 = upside down 3 = face-up (used in landscape mode) symbol-set: symbol set (number from 0 to 65535): 4 = ISO 60 Norway 5 = Roman Extension 9 = ISO 15 Italian 14 = ECMA-94 Latin - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 301
8-bit, 256 characters (All character codes. The printing system must be set to the HP transparency mode. See Emulation of the Technical Reference manual.) Function The SFA command specifies the attributes of the current bitmap font. It can be used to change the default attributes of the bitmap font - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 302
; FTMD 15; UNIT C; SLM 2; STM 4; FONT 1; SFA .25, 1, F; FONT 2; SFA .15, .5, P; FONT 1; EXIT; At these settings, in font mode 15, font 1 is double spaced (1 cm), !R! FONT 2; EXIT,E; while font 2 is single spaced (0.5 cm) with 1.5 mm spaces between words. !R! FONT 1; EXIT,E; The printer remembers the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 303
SFA Printout 293 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 304
Function The SFNT command selects the font which matches the type-face parameters. It enables the user table in Section 4.2. of the Technical Reference manual. Specify the full name exactly as it appears the font, using the unit of points regardless of the current unit setting. The SFNT command is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 305
one already assigned to another font, the printing system ignores the SFNT command. symbol-set uses HP PCL matching code to change the font's symbol set. Unsupported symbol set values, if specified, are ignored. compression squeezes or expands characters in the horizontal direction. Compression - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 306
PRESCRIBE Command Reference This is 10-point Helvetica-Nr, with Roman-8 symbol set, compression is 2, and shear is .3. You can later recall this font by the FONT 3000; command. !R! PAGE; EXIT; Printout 296 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 307
SGPC SGPC - Set kcGl Pen Color COLOR Format SGPC pen-number, color; Parameters pen-number: number from 1 to 8 corresponding to FRPO G1 to G8 parameter color: 0 = Black 1 = Red 2 = Green 3 = Yellow 4 = Blue 5 = Magenta 6 = Cyan 7 = White Function The SGPC command sets the color of a pen 1 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 308
Function The SHMI command sets the HMI. The parameter is measured in the unit value specfied by the UNIT command. File !R! RES; SLM 1; STM 2; EXIT; This line has the default spacing. !R! UNIT C; SHMI .3; EXIT; This line has a slightly wider spacing. !R! SFNT 'TimesNewRoman', 10; SHMI .3; EXIT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 309
(fill pattern), and GPAT (gray pattern) commands can be used for pattern images. With operation modes 1 and 2, the SIMG command takes care of the source image's transparency only. The default operation mode is 1. The white pixels of the source image do not overlay on the destination. For example - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 310
overlaid onto the destination. The pattern image fills only the area on the destination which is covered by white pixels. Note that the letter A is patterned only with its opposing quarters. operation mode = 6: Both source and pattern images are opaque, the entire letter A is patterned, and the full - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 311
File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 2.5, 0, 0, 2.5, -5, 0, 0, 2.5, 2.5, 0; PAT 1; SIMG 4; FILL 1; MRP -1, 3.5; PAT 18; FSET 4158T3B0S1P108V; TEXT "A"; FILL 1; PAGE; EXIT; Printout SIMG 301 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 312
by the system from either a single plane (monochrome) or 3-plane (8-color) RGB palette. The default palette is a monochrome palette. Colors and parameters specifiable by SCOL command for each palette are as created using the SIMP command. The currently acative palette ID does not change. 302 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 313
File !R! RES; UNIT C; SIMP 3; MCRO SIMP; NEWP; SCOL %2; PDRP 2, 0, 0, 2, -2, 0, 0, -2; FILL 1; PMRP .5, .5; ENDM; CALL SIMP,0,0; CALL SIMP,0,1; CALL SIMP,0,2; CALL SIMP,0,3; CALL SIMP,0,4; CALL SIMP,0,5; CALL SIMP,0,6; CALL SIMP,0,7; PAGE; EXIT; Printout SIMP 303 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 314
The SIR command accesses different levels of Kyocera Image Refinement (KIR). The image refinement level remains in effect until the printing system receives a RES command or a different SIR command. The default value is On. Refer to the User's Manual for details about how to obtain the optimum - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 315
SLJN SLJN - Set Line JoiN Format SLJN mode; Parameter mode: line join mode: 1 = Beveled join 2 = Mitered join 3 = Round join 4 = Notched join Function The SLJN command determines how two connected lines in a path are joined. The default join is beveled (1). Beveled join ends the lines with butt - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 316
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; SPD .5; SCAP 3; CMNT Round-capped at the upper-left corner; SLJN 3; CMNT Round-joined at other corners; PMZP 5, 16.5; PDRP 3, 0, 0, 3, -3, 0, 0, -3; STRK; NEWP; SCAP 1; CMNT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 317
from the left edge limit of the paper in the unit value designated by the UNIT command. If the margin is moved to the right of SRM command after the SLM command to restore the original right margin. File !R! RES; UNIT C; FONT 2; SFNT "TimesNewRoman"; SLM 1; EXIT; Location of 1-cm left margin - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 318
PRESCRIBE Command Reference Printout 308 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 319
of lines per inch Function The SLPI command sets the number of lines per inch (even if the UNIT command designates a non-inch unit). File !R! RES; STM 2; SFNT "Helvetica"; EXIT; These lines have the default spacing of six lines per inch. !R! SLPI 2; EXIT; These lines are spaced at two lines per inch - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 320
margin setting in a document file should be placed at the beginning of the file or at a page break. File !R! RES; UNIT C; SFNT "TimesNewRoman"; STM 1; SLS 1; SLPP 10; EXIT, E; Top margin at 1 cm, with 10 lines per page. (Line 1) Line 2 Line 3 Line 4 Line 5 Line 6 Line 7 Line 8 Line 9 Line 10 Line - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 321
SLPP Printout 311 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 322
command. SLPI sets the number of lines per inch. SLS sets the number of inches (or other units) per line. File !R! RES; UNIT C; STM 5; SFNT "TimesNewRoman"; EXIT; These lines have the default line spacing of 0.423 cm (6 lpi). !R! SLS .6; EXIT; These lines are spaced at intervals of .6 centimeters - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 323
a join to the width of the lines connected to each other. The default miter limit value is 10. In smaller miter-limit values, say 3, the miter join automatically switches to the beveled join. This switching prevents the problem of a spike extending beyond the intersection of the path because a small - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 324
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; PMZP 5, 15; SPD .5; SLJN 2; CMNT Mitered join; PDRP 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2; SMLT 10; CMNT Miter limit is 10; STRK; NEWP; PMZP 5, 19; SPD .5; SLJN 2; CMNT Mitered join; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 325
, etc. Parameters except monitor-name are enabled only when monitor-name value is 7 (custom). Resetting the printing system or switching emulation modes resets all custom parameters to the default states. The simulation provided by this command is enabled only when the device-dependent color space - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 326
to some color printing system models. At the time of release of this manual, the command is irrelevant to model FS-5800C; and monitor-name values of 0 and 2 are valid for model FS-8000C. Resetting the printing system and switching emulation mode reset all parameters to the default states. 316 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 327
SPAL SPAL - Select PALette COLOR Format SPAL id; Parameter id: palette ID number: 0 to 32767 (default is 0) Function The SPAL command selects the palette does not change. All palettes are deleted by the reset command, leaving only the default palette. File and Printout See ACLI on page 12. 317 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 328
of the line used in the graphics commands (DRP, PDRP, etc.). The thickness is specified in the unit value designated by the UNIT command. The maximum thickness is 4200 dots (14 inches or 35.56 centimeters) in path graphics mode, and 127 dots (0.42 inches or 1.08 centimeters) in standard graphics - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 329
SPD File !R! RES; UNIT C; STM 2; SLM 2; SLS .6; SFNT "Helvetica-Nr"; SPD 0.01; DRP 5, 0; TEXT ' 0.01 cm', N; SPD 0.02; DRP 5, 0; TEXT ' 0.02 cm', N; SPD 0.05; DRP 5, 0; TEXT ' 0.05 cm', N; SPD 0.1; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 330
break. The SBM (Set Bottom Margin) and SLPP (Set Lines Per Page) commands also set the bottom margin. File !R! RES; UNIT C; SFNT "TimesNewRoman"; STM 1; SLS 1; SPL 10; EXIT, E; Top margin at 1 cm, with 10 cm page length. (Line 1) Line 2 Line 3 Line 4 Line 5 Line 6 Line 7 Line 8 Line 9 Line 10 Line - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 331
SPL Printout 321 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 332
(lengthwise) Function The SPO command instructs the printing system how to orient switch to landscape orientation, the printing system resets the top margin to zero. The printing system uses separate bitmap fonts for portrait and landscape orientations. When the font mode manual for details. 322 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 333
SPO File !R! RES; SFNT 'TimesNewRoman-It', 10; CMNT This file is for an A4 cassette.; SPSZ 8; PAT 16, 300; UNIT C; MZP 4, 24; BOX 6, -6; MZP 7, 24; BOX 3, -3; BLK 3, -3; MZP 4, 24; TEXT, L; TEXT 'Portrait orientation'; SPO L; MZP 12, 10; BOX 6, -6; MZP 15, 10; BOX 3, -3; BLK 3, -3; MZP 12, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 334
SiZe Format SPSZ size-code [, ratio]; Parameters size-code: 0 = Same as the size of the paper cassette 1 = Monarch = Youkei 4†† ratio: Enlargement/reduction ratio (for print systems handling A3/ledger): 0 = 100% [Cassette size to cassette size] 5 = 70% [A3 to A4, B4 to JIS B5, A4 to A5] 6 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 335
particularly useful for printing on envelopes (size-code 1 through 4, 16, and 17). If size-code is 0, the printing system adjusts the edge limits to match the cassette size. size-code defaults to 0 at power-up and after a reset. Size codes 10 through 12, 19, and 30 are supported only by the printing - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 336
. The SRM (Set Right Margin) command also sets the right margin, but it measures from the left edge limit of the paper. File !R! RES; UNIT C; SLM 1; CMNT Emulation mode is 1 (IBM); SFNT "Univers-MdCd", 18; SLPI 4; SPW 10; EXIT; Line with 1-cm left margin and 10-cm width !R! SPW 8; EXIT; Line with - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 337
SPW Printout Related Command SRM 327 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 338
emulations. The SPW (Set Page Width) command also sets the right margin, but it measures from the left margin position. File !R! RES; UNIT C; SLM 1; CMNT Emulation mode is 1 (IBM); SFNT "Univers-MdCd", 18; SLPI 4; SRM 11; EXIT; Line with 1-cm left margin and 11-cm right margin !R! SRM 9; EXIT - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 339
SRM Printout Related Command SPW 329 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 340
of the logical page. Presentation modes 0 and 1 are depicted in the next page. The width and height options define the size of the raster area which has the current position as its left-top corner of the area. These options are measured in the dot unit regardless of the current designation of - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 341
affects the position of the current point, however. Current point Width Height Current point Width Height Portrait (SPO P;) Landscape (SPO L;) presentation-mode = 1 The orientation of the logical page determines the width and height of the raster image. The current position also depends on - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 342
by this command is 255. These logical operations directory map to their raster operations (ROP3). Logical operation value is eset to the default of 252 by the RES command. An error results and this command has no effect if the ROP3 value is outside the range 0 to 255. File !R! DAM; RES; MCRO - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 343
CALL DBOX,2; CALL DBOX,3; RES; EXIT; Printout SROP 333 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 344
only when the optional sorter is installed to the printing system. It instructs the printing system to deliver printed pages in the sorter mode. Each specified tray receives a complete set of pages, one copy of each. If the parameters are omitted, the top n trays are used, where n is the copy - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 345
values of 51, 52, and 61 are valid for certain copiers installed with the applicable option device. The STAK command should be placed at the top of a file or program. File !R! STAK 2; EXIT; PAGE 1 On printers with only one paper tray this file will be delivered face-down as usual, page 1 first - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 346
line width, as measured in the current unit (not available in KPDL mode) • Current memory allocations The above status settings are temporary conditions set by PRESCRIBE commands. They revert to their default values when power is switched off. Other status page information includes: • Miscellaneous - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 347
STAT Sample Status Page User status page Service status page 337 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 348
PRESCRIBE Command Reference STM - Set Top Margin Format STM distance; Parameter distance: size of top margin Function The STM command sets the top margin, in the unit value designated by the UNIT command. A top margin setting in a document file should be placed at the beginning of the file or - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 349
STM Printout 339 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 350
2 staples, printing 15 copies of the job: !R! STPL 3; STPC 5; JOBS 2, 15, 1, 0, 1, "Interim Report 1", "Steve", "09/22/02 19:24"; TEXT "This is Interim Report 1 ..."; PAGE; UNIT C; BOX 5,10; PAGE; JOBT; EXIT; 1 This value depends on the stapler to be used. 340 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 351
the pages of a job at the position specified by the position parameter (See above.) using a document finisher incorporating the stapler unit. With position 2 (top left), stapling is automatically straightened (vertical) when Legal size paper is used. Parameter values 50 to 54 are valid for certain - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 352
may be specified by STAK. (For the document finisher such as the DF-31, the MSTK command may be used to guide stapled pages to one of the output trays as desired.) STPL command causes a page break. File !R! STPL 3; CMNT Two staples on the left; JOBS 0,3,0,0; TEXT "Stapling Test, Page 1"; PAGE - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 353
, or 1200 dots per inch. The 200, 600, and 1200 dpi resolutions are available only for the printing system models that support the 600 or 1200 dpi printing resolution. The default value is 75 dots per inch. The STR command affects only PRESCRIBE raster graphics. It does not change the resolution of - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 354
, the STRK command clears the path and moves the cursor to the end of the path. File !R! RES; UNIT C; NEWP; PMZP 7, 17; SPD .2; PDRP -2.5, 0, 0, 2.5, 2.5, 0, 0, -2.5; PDRP 2.1, 1.25, 1.25, -2.1, -2.1, -1.25, -1.25, 2.1; PMRP 0, 2.5; PDRP 2.1, -1.25, 1.25, 2.1, -2.1, 1.25, -1.25, -2.1; STRK; PAGE - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 355
STRK Printout Related Commands FILL, NEWP 345 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 356
will control only underlines printed by the U-option in PRESCRIBE commands such as TEXT. File !R! RES; UNIT C; SLS 0.8; SFNT 'Helvetica-Nr', 12; TEXT 'Default paramaters', E, U; TEXT ', ', E; SULP .2, .1; TEXT 'heavier underlining', N, U; TEXT 'and even', E; SULP -.32, .04; TEXT 'OVERLINING - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 357
SULP Printout 347 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 358
command is relevant to the FS-1000 printer only. Note File To attribute the MP tray for thick paper and normal density: !R! TATR 0, 1, 3; EXIT; To reset the second paper cassette (option feeder) to the defaults: !R! TATR 2; EXIT; To reset all paper sources to the defaults: !R! TATR; EXIT; 348 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 359
location. The length of the string is unlimited, except that the command as a whole may not be longer than 255 characters. Carriage-return and linefeed codes in the string are ignored. 349 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 360
PRESCRIBE Command Reference File !R! RES; UNIT C; MAP 2, 2; SFNT 'Univers-MdCd'; TEXT 'Check desired options:', L, U; FONT 2; BOX .1, -.1; TEXT 'Power steering', L; BOX .1, -.1; TEXT 'CD auto changer', L; BOX .1, -.1; TEXT 'Air conditioner', L; PAGE; EXIT; Printout - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 361
as 1-byte or 2-byte character code while printing using a text command. To parse such characters, the current font must supports 2-byte characters and a 2-byte symbol set such as Windows 3.1J (19K). The pursing method will automatically be shift JIS encoding (2) if the default font and symbol set is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 362
1 is automatically set to the tray parameter. Function The TRSM command instructs printing system to insert blank or printed page between each transparency. The printing system loads transparency from MP tray and inserting paper from the paper source other than MP tray. When face-down printing, the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 363
UNIT UNIT - set UNIT of measurement Format UNIT code; Parameter code: I = inches C = centimeters P = points D = dots Function The UNIT command sets the unit of measurement used in other PRESCRIBE commands. The initial unit is inches. Other supported units of measurement can be calculated as - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 364
PRESCRIBE Command Reference Printout 354 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 365
UOM command applies only to the printing system models that support the 600 dpi resolution. It defines the unit of measurement in dots per inch for cursor movements. The command requires that the UNIT value be set to D. The default unit of measurement is 300 (dpi). For example, the cursor movement - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 366
PRESCRIBE Command Reference Printout Related Command UNIT 356 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 367
is to be set for a virtual mailbox for which a password is set, that virtual mailbox's password is required. An error will be displayed on the operator panel if no password or the incorrect password is specified. (See the Technical Reference manual.) Note that if command syntax is incorrect, such as - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 368
by issuing multiple instances of this command. If no virtual mailbox corresponds to the alias given, an error will be displayed on the operator panel. (See the Technical Reference manual.) This command is irrelevant to photocopy virtual mailbox function. Note Files To stack jobs on virtual - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 369
fails or no virtual mailbox corresponds to the alias given. For error displays, see the Technical Reference manual. The master password is valid as the current password for all virtual mailboxes. Virtual mailboxes for which a password has been set are not shown on the VMB LIST page (See - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 370
PRESCRIBE Command Reference Files To set 9999 as the password for virtual mailbox number 3 for which no password is set: !R! VMPW 3, 0, 9999; EXIT; To set no password for the virtual mailbox with the alias MyMailbox for which the password 9999 had been set: !R! VMPW "MyMailbox", 9999, 0; EXIT; To - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 371
WIDE WIDE - set WIDE A4 mode Format WIDE mode; Parameter mode: 0 = Off 1 = On Function The wide A4 function widens the A4 printing width in order to prevent unnatural line breaks or clipping of graphics in cases - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 372
PRESCRIBE Command Reference WRED - WRite EnD Format WRED; Parameter None Function The WRED command terminates a sequence of writing data to the memory card or to the hard disk, using one of the commands listed below. The WRED command can be renamed to a string of ASCII characters if - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 373
XBAR XBAR - print two dimensional barcode Format XBAR [data-length]; data-string;ENDB; or XBAR buffer-name;ENDB; Parameters data-length: length of data in bytes, terminated with a semicolon (;) If this value is omitted, data-string is counted all characters after the first semicolon until the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 374
PRESCRIBE Command Reference Files !R! XBAR; The Milky Way is a gravitationally bound collection of roughly a hundred billion stars. Our Sun is one of these stars and is located roughly 24,000 light years (or 8000 parsecs) from the center of our the Milky Way. The Galaxy has three major components. - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 375
0 XBCP 0 - select barcode type/reset all other XBCP parameters Format XBCP 0[, type]; Parameter type: two dimensional barcode type: 1 = PDF417 (only type currently supported) Function The XBCP 0 command selects a barcode type and resets all parameters to the defaults. File See XBCP 1 (page - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 376
Default is 3 dots. Function PDF417 supports 8 different bar and space widths. The each width is a multiple of 1 to 8 times of the narrowest element width. The XBCP command set to mode 1 specifies the narrowest element width (narrowest bar width) in the current unit reverted to its default (3 dots). - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 377
Parameter percentage: value between 0 and 400 Function PDF417 supports an error correction scheme. The XBCP 2 command specifies the error correction level as a percentage of the number of code word values for the data to be encoded. An illegal value defaults to 10. Note that XBCP 3, as explained on - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 378
level by predetermined values. An illegal value defaults to 0. Note that the execution of XBCP 3 overrides the setting of XBCP 2 and remains valid until RES (reset) or XBCP 0. File To sets the error correction level to level 4: !R! RES; XBCP 3, 4; XBAR;Error correction can also be set by level - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 379
90 Function The XBCP 4 command sets the number of data code word rows in the PDF417 barcode. Illegal values make XBCP 4 ignored. XBCP 6 default provides default. Note that this command is not effective if XBCP 8 is issued. Precedence of XBCP modes is: 46, 4+8< 6. File To set 20 rows of barcode - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 380
words at each end of the row which are not counted as data code words. XBCP 6 default provides default. Note that this command is not effective if XBCP 8 is issued. Precedence of XBCP modes is: 56, 5+8 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 381
to 1: 2. Default is 1: 2. Note that this command is not effective if XBCP 4 and/or 5 is issued, however, this has the highest priority if both XBCP 8 and XBCP 4 and/or 5 are issued together. Precedence of XBCP modes is: 4/56, 4/5+8 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 382
PRESCRIBE Command Reference Printout Aspect ratio is 3:2 in vertical and horizontal directions. Aspect ratio is normal. 372 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 383
to element width, ranging from 1 to 10 Function The XBCP 7 command determines the bar height by a ratio to the narrowest element width. An illegal value defaults to 3. File To set the module height twice as high as the element width: !R! RES; XBCP 7, 2; XBAR;Visit Sea World, the world famous San - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 384
automatically set rows and columns so that it satisfies the requirement that the multiplication of rows times columns is less than or equal to 928. Default is disabled. Note that the XBCP 8 overrides XBCP 4 and/or 5 which set the number of rows and columns. However, this command is not effective if - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 385
XBCP 9 XBCP 9 - enable truncation Format XBCP 9; Parameter None Function The XBCP 9 command can generate a truncated PDF417 symbol that omits the right row indicator and the stop pattern. Default is non-truncation. 375 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 386
defines its contents. The string must be surrounded by single or double quote marks, be less than 200 characters long and only contain EXC mode compaction characters (20H~7FH). This command is ignored if the string does not satisfy these conditions. The execution of this command automatically sets - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 387
Parameter None Function A Macro PDF417 symbol contains an optional block count field. The XBCP 11 command enables this function. Default is not enabled. The execution of this command also automatically sets Macro PDF417 symbol mode. File !R! RES; XBCP 11; MZP 1,0; XBCP 18,0; XBAR; ... ... EXIT; 377 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 388
symbol contains an optional time stamp field. The XBCP 12 command enables this function. The execution of this command also automatically sets Macro PDF417 symbol mode. File To set time stamp at 06:15:30AM on Jan. 2, 1970: !R! RES; XBCP 12, 108930; MZP 1,0; XBCP 18,0; XBAR; ... ... EXIT; 378 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 389
A Macro PDF417 symbol contains an optional Sender ID field. The XBCP 13 command enables this field and defines its contents. The string must be surrounded by single or double quote marks, be less than 200 characters long and only contain EXC compaction mode characters (20H~7FH). This command is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 390
A Macro PDF417 symbol contains an optional Addressee ID field. The XBCP 14 command enables this field and defines its contents. The string must be surrounded by single or double quote marks, be less than 200 characters long and only contain EXC compaction mode characters (20H~7FH). This command is - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 391
an optional file size field. The XBCP 15 command enables this function. Note that the execution of this command also automatically sets Macro PDF417 symbol mode. This function is disabled in default condition. File !R! RES; XBCP 15; MZP 1,0; XBCP 18,0; XBAR; ... ... EXIT; 381 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 392
PDF417 symbol contains an optional checksum. The XBCP 16 command enables this function. Note that the execution of this command automatically sets Macro PDF symbol mode. This function is disabled in default condition. File !R! RES; XBCP 16; MZP 1, 0; XBCP 18, 0; XBAR; ... EXIT; 382 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 393
ID is generated when XBCP 10 through 16 or XBCP 18 are executed without executing XBCP 17. The string must be surrounded by single or double quotation marks, be less than 50 characters long and only contain EXC compaction mode in File below. File In Macro PDF mode, data such as large as 3000 bytes - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 394
PRESCRIBE Command Reference Printout 384 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 395
mode directs the reader to separate large data and allows Macro PDF417 two dimensional barcodes with a single file-id. File To bar-code data 'abcdXYZ12345' as a Macro PDF417 using block indices 0, 1, and 2: !R! UNIT C; CMNT Set unit to centimeters; XBCP 17,"file-id"; CMNT Set file ID to file-id - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 396
PRESCRIBE Command Reference Printout 386 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 397
current coordinate (like the MRP command described on the printing system's manual). The remaining pairs of positioning parameters are ignored if there are no below, the second line XBCP 17 activates Macro PDF mode and specifies QualitySt for file-id. The third line MZP command positions the first - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 398
Printout 1 File 2 To print 4 30-column-by-20-row PDF symbols at specified locations in Macro PDF mode. In example below, the first line XBCP command resets all XBCP parameters to the defaults and selects the barcode type for PDF417 (though it is the only type currently available); the second line - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 399
Printout 2 XBCP 19 File 3 To print multiple Macro PDF barcodes beyond the current page. In the example below, the fourth line XBCP 19 has no coordinating parameters specified. This allows the first segment barcode of the ensuing PDF data to be positioned at the current cursor position and the - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 400
PRESCRIBE Command Reference Printout 3 First page Second page 390 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 401
example, F-1 and GRY-2 are valid buffer names. As the above Format instruction implies, the XBUF command sequence can have two other formats implementing the different name from the printing system memory. The XBUF command sequence with no comma, buffer-name and data-length specified XBUF; - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 402
PRESCRIBE Command Reference Files is used to delete all buffer name from the printing system memory. ... XBCP 0,1; XBUF PDF 1, 25; This is a PDF417 example. ;ENDB; XBUF PDF 2, 15; This is a test. ;ENDB; ... XBAR PDF 1; MRP 1,1; XBAR PDF 2; The sixth line prints - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 403
from 100 to 105 bitmap: dot pattern of the pattern, coded as a character string Function The XPAT command generates a new, path. Details for creation of new patterns appear in Chapter 4 of the Technical Reference manual. File !R! RES; UNIT C; MAP 5, 5; XPAT 105;//?//?p@0p@0p@0p@0p@0p@0p@0p@0p@0p@0p@ - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 404
PRESCRIBE Command Reference 394 - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 405
Index - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 406
, 52 Clipping rectangle, 55 Code set, 129, 226, 268 lightness, 155 color matching, 159 commands, 93 Destination image, 300 Downloading character, 147 Drawing rule 98 e-MPS, 165 limiting values for storage, 165 e-MPS starting, tray, 335 Face-up output tray, 335 Fill, 184 Fill pattern, 110 8 by 8 bit, - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 407
Firmware, mode, 119 Fuser mode, 162, 163 G Graphics state, 228, 272 Gray pattern, 122 Grouping, 27 H Hard disk, 141, 246, 250, 256, 258 error codes level, 304 KPDL, 287 Kyocera Image Refinement, 304 L top, 338 Margine left margin, 307 Media type, 162, 163, 172 attributing media type, 162, 163 Memory - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 408
Resetting the printer tray, 335 stacker, 171 Staple, 141, 340 changing number of pages, 340 position, 341 Starting a new page, 179 Starting a new path, 176 Starting angle, 28, 182, 199 Status page, 336 user mode and service mode, 336 Symbol set, 65, 129, 226, 268, 294 as a bitmap attribute, 290 ID - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 409
, 299, 352 TrueType, 153, 247 loading ..., 153 Two-dimentional barcode addressee ID, 380 automatic rows and columns, 374 bar height, 373 block count, 377 checksum, 382 data code word columns, 370 data code word rows, 369 error correction level, 368 error correction level by percentage, 367 file - Kyocera KM-1650 | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 410
Rev. 4.8 2009.7
Command Reference
PRESCRIBE Commands