Lantronix xPico Wi-Fi Freescale Tower System Module Application Note: xPico Wi
Lantronix xPico Wi-Fi Freescale Tower System Module Manual
 |
View all Lantronix xPico Wi-Fi Freescale Tower System Module manuals
Add to My Manuals
Save this manual to your list of manuals |
Lantronix xPico Wi-Fi Freescale Tower System Module manual content summary:
- Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 1
Application Note: Demo programs for using the Lantronix® standard tunnel with a Kinetis™ microcontroller and the xPico® Wi-Fi® Tower Board Lantronix, Inc. 167 Technology Drive Irvine, CA 92618 Tel: +1 (949) 453-3990 Part Number 920-929 Revision A November 2013 - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 2
xPico® Wi-Fi® Tower Board Demos Application Note Intellectual Property © 2013 Lantronix, Inc. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of Lantronix. xPico and Lantronix are registered - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 3
Demos Application Note Lab Setup For the following labs, connect an xPico® Wi-Fi® Tower Board and a Freescale™ Kinetis™ K60 Tower board into the Tower system. Other microcontroller boards can be used, however the firmware will slightly change as different MCU boards have different connections for - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 4
Download. 13. Make sure that your laptop Wi-Fi is connected to the xPico Wi-Fi device's SoftAP: a. Look for SSID xPicoWiFi_xxxxxx where the last 6 characters are the last 6 characters of the xPico Wi-Fi serial number b. Default password is XPICOWIFI 14. Once the Debugger window is active, click - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 5
on the module label. For example if the serial number. 2. Connect your device to the xPico Wi-Fi device's Soft AP SSID. The default password is XPICOWIFI. 3. Open a standard browser and in the address field of the browser enter the following URL; xpicowifi.lantronix.com or alternatively use - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 6
Status, then look for "IP Address" under Interface (wlan0) to see the IP address that was assigned to the xPico Wi-Fi by the infrastructure network. 9. You can now connect to the xPico Wi-Fi from the infrastructure side and the Soft AP side. 10. Configure the tunnel for the later labs: 11. Click on - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 7
is sent in response to the commands via the first UART. 1. Unzip the source code with this lab into a directory. 2. xPico Wi-Fi tunnel configuration must be set per instructions in Lab 2. 3. In CodeWarrior, click on File -> Import. In the dialog box that comes up, select "Existing Projects into - Lantronix xPico Wi-Fi Freescale Tower System Module | Application Note: xPico Wi - Page 8
The Kinetis K60 should be running the same firmware used in the previous lab. 3. The xPico Wi-Fi Tunnel configuration should be set the same xPico Wi-Fi is sending and receiving data. 5. Using a web browser, navigate to http://ltrxpost.appspot.com. 6. Find the serial number of your xPico Wi-Fi on
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
Application Note:
Demo programs for using the
Lantronix® standard tunnel with a
Kinetis™ microcontroller and the
xPico® Wi-Fi® Tower Board
Lantronix, Inc.
167 Technology Drive
Irvine, CA 92618
Tel: +1 (949) 453-3990
Part Number 920-929
Revision A
November 2013