Lenovo Storage S2200 (English) Rackmount Braket Kit - Lenovo Storage S3200, S2

Lenovo Storage S2200 Manual

Get Lenovo Storage S2200 PDF manuals and user guides View all Lenovo Storage S2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Lenovo Storage S2200 manual content summary:

  • 1
  • 2
Before you begin
•
Verify that the installation site meets the enclosure’s
requirements for space and airflow, temperature, and
power. For additional information see the web-posted
Lenovo Storage Setup Guide
at
;
select Product Support, and navigate to Storage Products.
•
Considering your system configuration and weight
distribution, determine where you will install each enclosure
within the rack or cabinet. Install the first enclosure in the
lowest rack space you plan to use. Install each remaining
enclosure into the next-higher available space within the
rack, until all enclosures are secured in place.
•
Confirm that you have cables of appropriate type and
length to connect to hosts and to power outlets.
CAUTION:
Be sure you are properly grounded before
touching a static-sensitive component to minimize potential
for electronic discharge.
Copyright Lenovo 2015.
LIMITED AND RESTRICTED RIGHTS NOTICE:
If data or software is delivered
pursuant a General Services Administration “GSA” contract, use, reproduction,
or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Lenovo, the Lenovo logo, BladeCenter, Flex System, NeXtScale System, and
System x are trademarks of Lenovo in the United States, other countries, or
both.
The material in this document is for information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of
this document to assure its accuracy, changes in the product design can be
made without reservation and without notification to its users.
The person using these instructions must be qualified to service
and install storage products.
CAUTION:
Two people are needed to lift and move the
enclosure. Use care to avoid injury.
Required tools
#2 Phillips screwdriver and antistatic protection devices
Rackmount bracket kit hardware
* Hanger fasteners may be pre-installed on the rail’s front and rear
mounting flanges (noted in Step 2).
Fasteners provided vary by rail kit. Alpha codes (in hardware table)
correlate to numeric P/Ns within illustrated procedures.
1. Attach side brackets
Using a total of four #8-32 x 3/16 flathead Phillips screws (two
per bracket), attach the side bracket to rear mounting holes on
each side of the chassis. The illustration below shows bracket
alignment for a 12-drive enclosure.
The illustration below shows bracket alignment for a 24-drive
enclosure.
2. Install hanger fasteners
NOTE:
Proceed to Step 3 for either condition:
•
Hanger fasteners are pre-installed in rail sets; or
•
You are installing into a rack with pre-tapped holes.
If installing into square or round-hole racks, install the hanger
fasteners in the front and rear rail components with the heads
facing inward. Front rail sleeves require two pins each, and
rear rail inserts each require one pin. Loosely attached
fasteners temporarily hold the rails in place before being
secured, enabling vertical and horizontal positioning for
accurate alignment.
3. Install rails
Complete sub-steps 1-9 (following) to install the rails.
1. Slide the rear rail insert into the front rail sleeve.
2. To determine the cabinet depth required by the rails, fit the
rail assembly to the rack and note which tapped holes in
the rear rails align with the front rail’s slotted holes. If cage
nuts are pre-installed, remove them from the locations
where hanger screws are inserted.
3. Using the measurements recorded in sub-step 2 above,
select two or three #8-32 x 3/8 flathead Phillips screws
(depending on your cabinet depth) to loosely attach the
rear rail to the front rail. You will tighten the screws later.
4. For square-hole racks, install cage nuts in the front and rear
rack holes where rails will be attached (see first illustration
on flip-side of page). For round-hole racks, use clip nuts
instead.
Position the rail’s front and back mounting flanges so that
through holes align with corresponding rack holes, and note
the locations. Attach three fasteners at the front of the rack,
and two at the rear, per the "
X
" marks shown in the
following installation detail views.
NOTE:
The rail kit supports multiple controller and
expansion enclosure models. The following illustrations
show a 12-drive enclosure.
Code
Item description
Qty
Rails and brackets
-
Side bracket
2
-
Left rail (front sleeve with rear insert)
1-ea.
-
Right rail (front sleeve with rear insert)
1-ea.
Screws
-
Hanger fasteners*
6
A
#8-32 x 3/16, FH100, PLP, SS
4
B
#8-32 x 3/8, FH, PLP2, SS
6
C
#10-32 x 3/4, Truss, PLP, SS; or
M5 x 10, PH, PLP2, SS; or
M6 x 10, PH, PLP2, SS
8
D
#10-32 x 5/8, FH100, PLP2, SS; or
M5 x 10, FH, PLP2, SS; or
M6 x 10, FH, PLP2, SS
2
E
#6-32 x 1/4, PH, PLP, SS, Patchlock
2
Nuts
F
#10-32, UNF - Cage Nut; or
#10-32, UNF - Clip Nut
10
Use fasteners that pertain to your rack type.
Code A — P/N:01-00000142
Code A — P/N:01-00000142
Hanger fasteners (pins)
may be pre-installed
Rear rail insert
Front rail sleeve
Rail components
Code B — P/N:01-00000262-00-01
Assembled adjustable-length rail
Storage Rackmount Bracket Kit
Installation