Lexmark 13P0150 Service Guide

Lexmark 13P0150 - C 750dtn Color Laser Printer Manual

Get Lexmark 13P0150 - C 750dtn Color Laser Printer PDF manuals and user guides
UPC - 734646521505
View all Lexmark 13P0150 manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark 13P0150 manual content summary:

  • Lexmark 13P0150 | Service Guide - Page 1
    LexmarkTMC750 5060-XXX • Table of Contents • Start Diagnostics • Safety and Notices • Trademarks • Index • Manuals Menu Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
  • Lexmark 13P0150 | Service Guide - Page 2
    6000-XXX -ii
  • Lexmark 13P0150 | Service Guide - Page 3
    5060-XXX Edition: November 2001 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
  • Lexmark 13P0150 | Service Guide - Page 4
    5060-XXX
  • Lexmark 13P0150 | Service Guide - Page 5
    Message Table 2-23 Service Checks 2-43 Cartridge Drive Assembly Service Checks 2-43 Fan Service Checks 2-48 AC and DC Power Service Check 2-50 Second Transfer Roll Service Check 2-52 Output Expander Service Check 2-53 5-Bin Mailbox Service Check 2-60 Print Quality Service Checks 2-66
  • Lexmark 13P0150 | Service Guide - Page 6
    5060-XXX Diagnostic Aids 3-1 Diagnostic Mode 3-1 Exiting the Diagnostics Mode 3-1 Device Tests 3-2 Quick Disk Test 3-2 Disk Test/Clean 3-2 Flash Test 3-3 Duplex Tests 3-3 Duplex Quick Test 3-3 Duplex Sensor Test 3-4 Error Log 3-4 Viewing the Error Log 3-4 Clearing the Error Log 3-4
  • Lexmark 13P0150 | Service Guide - Page 7
    Registration 3-18 ITU Alignment 3-19 Setting Printer Alignment 3-19 HCIT Standalone Test Mode Printhead Adjustments 4-1 Printhead Manual Adjustment 4-1 Printhead Electronic 4-21 Operator Panel 4-25 Cartridge Drive Motor Assembly (Yellow 4-26 Cartridge Drive Motor Assembly (Cyan,
  • Lexmark 13P0150 | Service Guide - Page 8
    4-35 RIP Card Shield Assembly 4-36 HVPS Developer Board 4-36 VTB Fan 4-37 Cartridge Drive Assembly 4-38 ITU Drive Motor Assembly 4-38 Engine Board Shield 4-39 Waste 5-24 Preventive Maintenance 6-1 Safety Inspection Guide 6-1 Lubrication Specifications 6-1 Scheduled Maintenance 6-2 vi
  • Lexmark 13P0150 | Service Guide - Page 9
    Feeder (MPF 7-12 Assembly 7: 500-Sheet Integrated Tray 7-14 Assembly 8: Autocompensator Assembly 7-16 Assembly 9: ITU Assembly 7-17 Assembly 10: Cartridge Contact Assembly 7-18 Assembly 11: Electronics 7-20 Assembly 12: Output Expander 7-30 Assembly 13: 5-Bin Mailbox 7-34 Assembly 14: 500
  • Lexmark 13P0150 | Service Guide - Page 10
    5060-XXX viii
  • Lexmark 13P0150 | Service Guide - Page 11
    in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above Class I level during normal operation, user maintenance, or prescribed service condition. Laser Der Drucker erfüllt gemäß amtlicher Bestätigung der
  • Lexmark 13P0150 | Service Guide - Page 12
    condições de assistência prescritas. Laserinformatie De printer voldoet aan de eisen die gesteld worden aan klasse I worden niet als ongevaarlijk aangemerkt. De printer is voorzien van een laser van klasse IIIb ( 795 nanometer. Het lasergedeelte en de printer zijn zo ontworpen dat bij normaal gebruik
  • Lexmark 13P0150 | Service Guide - Page 13
    person utsätts för laserstrålning över Klass I-nivå vid normal användning, underhåll som utförs av användaren eller annan föreskriven serviceåtgärd. Laser-melding Skriveren er godkjent i USA etter kravene i DHHS 21 CFR, underkapittel J, for klasse I (1) laserprodukter, og er i andre land godkjent
  • Lexmark 13P0150 | Service Guide - Page 14
    prendre toutes les précautions nécessaires. Norme di sicurezza • Il prodotto è stato progettato, testato e approvato in conformità a severi standard di sicurezza e per l'utilizzo con componenti Lexmark specifici. Le caratteristiche di x Service Manual
  • Lexmark 13P0150 | Service Guide - Page 15
    Funktionen der Bauteile und Optionen sind nicht immer offensichtlich. Sofern Teile eingesetzt werden, die nicht von Lexmark sind, wird von Lexmark keinerlei Verantwortung oder Haftung für dieses Produkt übernommen. • Die Wartungsinformationen für dieses Produkt sind ausschließlich für die Verwendung
  • Lexmark 13P0150 | Service Guide - Page 16
    amb la utililització de components específics de Lexmark. Les característiques de seguretat d'algunes peces pot ser que no sempre siguin òbvies. Lexmark no es responsabilitza de l'us d'altres peces El personal professional ha d'estar-ne assabentat i prendre les mesures convenients. xii Service Manual
  • Lexmark 13P0150 | Service Guide - Page 17
    table, symptom tables, and service checks used to isolate failing field replaceable units (FRUs). 3. Diagnostic Aids contains tests and checks used to locate or repeat symptoms of printer problems. 4. Repair Information provides instructions for making printer adjustments and removing and installing
  • Lexmark 13P0150 | Service Guide - Page 18
    5060-XXX xiv Service Manual
  • Lexmark 13P0150 | Service Guide - Page 19
    add up to three optional drawers to the base printer, which can increase the printer's paper capacity to 2000 sheets. The Lexmark C750 (5060-XXX) laser printer is available in three models: 5060-001 5060-002 5060-003 Tools Required For Service Flat-blade screwdriver #1 Phillips screwdriver, magnetic
  • Lexmark 13P0150 | Service Guide - Page 20
    Only Memory Synchronous Dual Random Access Memory Single Inline Memory Module Static Random Access Memory Used Parts Return Volts alternating current Volts direct current Yellow 1-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 21
    checks to determine the corrective action necessary to repair a malfunctioning printer. Note: There may be printer error messages that are not contained in this service manual. Call your next level support for assistance. • "Symptom Table" on page 2-1 • "Error Code Table" on page 2-3 • "Sub Error
  • Lexmark 13P0150 | Service Guide - Page 22
    page Fuser Problem - Fuser Cold Action Go to the "Paper Path Service Check" on page 2-97. Go to the "Tray 1 Service Check" on page 2-90. Go to "Autocompensator Service Check" on page 2-91. Go to the "Multipurpose Feeder (MPF) Service Check" on page 2-94. Check to make sure that the printer is not
  • Lexmark 13P0150 | Service Guide - Page 23
    the "Paper Path Service Check" on page 2-97. Go to "Cover Open/HV Interlock Switch Service Check" on page printer off and on to try and clear the error code. If this does not fix the problem after several attempts, call your next level support before replacing the Engine Board. Paperport link driver
  • Lexmark 13P0150 | Service Guide - Page 24
    2-4 Service Manual 5060-XXX Action Tray 2 Transparency Sensor Error - Replace Tray 2 Transparency Sensor Assembly. If this does not fix the problem, replace fix the problem, replace: "Engine Board" on page 4-13 Cyan TMC switch failure - Go to the "Cyan Cartridge Drive Assembly Service Check" on page
  • Lexmark 13P0150 | Service Guide - Page 25
    the "Yellow Cartridge Drive Assembly Service Check" on page 2-47. Black TMC switch failure - Go to the "Black Cartridge Drive Assembly Service Check" on the "HVPS Transfer Board" on page 4-12. If this does not correct the problem, replace the "Engine Board" on page 4-13. Transfer Servo Start Error -
  • Lexmark 13P0150 | Service Guide - Page 26
    to see if this fixes the problem. If it does not fix the problem, replace the "RIP Board" on page 4-11. If it does fix the problem replace the defective RAM. Download connected correctly. Go to the service check for the device indicated. Invalid command parameter received by the specified device
  • Lexmark 13P0150 | Service Guide - Page 27
    6 to 20) Note: This message is used for multiple bin output devices. Go to the service check for the device indicated. ITU Stall - Replace "ITU Assembly" on page 4-40. Invalid "RIP Board" on page 4-11 If this does not fix the problem replace: Cyan Printhead Assembly - Go to "Printheads" on page 4-33
  • Lexmark 13P0150 | Service Guide - Page 28
    Printhead Error 110 Printhead Error 111 Printhead Error 2-8 Service Manual 5060-XXX Action Magenta Printhead Lost Hsync Check for to perform the "Printhead Adjustments" on page 4-1. If this does not fix the problem replace: "RIP Board" on page 4-11 No first Hysnc - Magenta Replace the following
  • Lexmark 13P0150 | Service Guide - Page 29
    on page 4-33. Note: Whenever a printhead assembly is replaced it is necessary to perform the "Printhead Adjustments" on page 4-1. If this does not fix the problem replace: "RIP Board" on page 4-11 Wrong Fuser Lamp - Hot Roll - Replace with correct lamp. Go to "Error Code 120 Error Code 121" on page
  • Lexmark 13P0150 | Service Guide - Page 30
    to "Error Code 136" on page 2-85. DC Motor Accel Stall - Staging - Replace the following FRU: Staging Motor Assembly If this does not fix the problem, replace: "Engine Board" on page 4-13 2-10 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 31
    this does not fix the problem replace: "Engine Board" on page 4-13 Fuser Drive Motor unable to lock - Go to "Error Code 149 Error Code 155" on page 2-84. Black Cartridge Motor unable to lock - Go to "Black Cartridge Drive Assembly Service Check" on page 2-44. Magenta Cartridge Motor Unable to lock
  • Lexmark 13P0150 | Service Guide - Page 32
    Motor 170 Motor 171 Motor 2-12 Service Manual 5060-XXX Action Black Cartridge Motor lost lock - Go to "Black Cartridge Drive Assembly Service Check" on page 2-44. Magenta Cartridge Motor lost lock - Go to "Magenta Cartridge Drive Assembly" on page 2-44. Cyan Cartridge Motor lost lock - Go to "Cyan
  • Lexmark 13P0150 | Service Guide - Page 33
    " on page 4-1. Mirror Motor lock not achieved - Magenta - Replace the following FRU: "RIP Board" on page 4-11 If this does not fix the problem, replace: Magenta Printhead Assembly - Go to "Printheads" on page 4-33. Note: Whenever the printhead assembly is replaced it is necessary to perform the
  • Lexmark 13P0150 | Service Guide - Page 34
    Error 189 PSD Error 190 PSD Error 191 PSD Error 192 PSD Error 2-14 Service Manual 5060-XXX Action EOS sensor out of range scan direction (Black) - Replace Adjustments" on page 4-1. No EOS reading (Black) - Go to "PSD Service Check" on page 2-88. Note: It is necessary to remove the Printhead
  • Lexmark 13P0150 | Service Guide - Page 35
    Adjustments" on page 4-1. No EOS reading (Magenta) - Go to "PSD Service Check" on page 2-88. Note: It is necessary to remove the Printhead Assembly Sub Error Code Table The Sub-Error code table may be helpful troubleshooting the printer when 9xx and 1xx Error Codes have been displayed. When a 9xx
  • Lexmark 13P0150 | Service Guide - Page 36
    reversing motor error detected, the engine has detected a PWM error condition. Duplex reversing motor error has been detected, the engine detected a motor encoder error. 2-16 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 37
    5060-XXX Sub Error Code Explanation 2D 32 2D 33 A Tray 2 pick motor stall error detected A Tray 2 pick motor PWM error detected 2D 34 2D 35 2D 36 2D 37 2D 38 A Tray 2 pick motor encoder error detected A Tray 2 feed motor stall error detected A Tray 2 feed motor PWM error detected A Tray 2 feed
  • Lexmark 13P0150 | Service Guide - Page 38
    number of times the LED blinks and use the following table to determine the problem. LED blinks 1 2 3 4 5 6 7 8 9 10 11 12 Problem Jam at registration sensor S2 Jam before the leading edge of the paper reaches adjustment of the mirror reflection sensors or EEPROM initialization 2-18 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 39
    to access the jam area. If sheets have Go to the "Paper been accumulated to be stapled or offset when Path Service Check" the jam occurred, the printer alternately flashes on page 2-97 the primary and secondary messages to indicate that all accumulated sheets not be removed during the jam
  • Lexmark 13P0150 | Service Guide - Page 40
    mismatch. Open the printer left door to access detected, the printer alternately flashes procedure. The printer will not reprint occurred, the printer alternately flashes the procedure as the printer will not jam occurred, the printer alternately flashes the procedure as the printer will not
  • Lexmark 13P0150 | Service Guide - Page 41
    Go to the sensor mismatch. If sheets have been "Autocompensator accumulated to be stapled or offset when the jam Service Check" on is detected, the printer alternately flashes the page 2-91 primary and secondary messages to indicate that all accumulated sheets should not be removed during
  • Lexmark 13P0150 | Service Guide - Page 42
    when the jam occurred, the printer alternately flashes the primary and secondary jam clearance procedure as the printer will not reprint the removed when the jam occurred, the printer alternately flashes the primary and secondary jam clearance procedure as the printer will not reprint the removed
  • Lexmark 13P0150 | Service Guide - Page 43
    Finisher Leave Job in Finisher Leave Job in Finisher Primary: This message indicates that a paper jam has occurred at or near the printer Input Sensor. Open the printers left door (Paper Jam Removal Door) to access the jammed media. Secondary: If sheets have been accumulated to be stapled when the
  • Lexmark 13P0150 | Service Guide - Page 44
    mismatch. Open the printer left door to the printer alternately flashes sheets are removed the printer will not reprint these the printer alternately flashes sheets are removed the printer will not reprint these detected, the printer alternately flashes are removed the printer will not reprint these
  • Lexmark 13P0150 | Service Guide - Page 45
    the accumulated sheets should not be removed during jam clearance. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled
  • Lexmark 13P0150 | Service Guide - Page 46
    detected, the printer alternately flashes sheets are removed the printer will not reprint these been cleared, the printer does not reprint any message will be displayed when the printer has detected at POST, that Alignment Procedure is in process and the printer is prompting the user for the X
  • Lexmark 13P0150 | Service Guide - Page 47
    that is uncalibrated. This message usually means a user-correctable NVRAM problem or the tray was not calibrated at the factory or needs to be calibrated. This message will be displayed when the printer has detected a refilled prebate cartridge. can be one of the following: *Black, CYAN
  • Lexmark 13P0150 | Service Guide - Page 48
    operate the printer with the option removed. If the problem continues, turn the printer off and back on. If the message continues to be displayed, turn the printer off, remove the option and call for service. Close lost for the following action: * Press Go to format the disk. 2-28 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 49
    the Stapler Door has been closed. The following actions can be taken when this message is displayed: * Install the staple cartridge or * Press Go to ignore this message. The printer will now handle staple jobs as if the staple unit were installed with no staples. The "Staples Empty" warning will
  • Lexmark 13P0150 | Service Guide - Page 50
    while this message is displayed: * A new staple cartridge may be installed to clear this message and start/ this print job by pressing Go or Select. The printer will resume printing, however the print job for which Menu: * Cancel Job * Reset Printer * Reset Active Bin * Check Supply Levels Note: Menu
  • Lexmark 13P0150 | Service Guide - Page 51
    1, Tray 2, Tray 3, Tray 4 or Tray 5 Note: This message will most likely be displayed when refilling the trays during a job. Before filling tray x take the printer off line by pressing the Stop button and waiting for pages to reach the output bin before refilling trays. The following actions can be
  • Lexmark 13P0150 | Service Guide - Page 52
    print cartridge is inserted. Replace the defective print cartridge. This message will be displayed when the front cover is closed with the wrong print cartridge installed. This message will be displayed when the printer has detected a calibration error for a particular color. 2-32 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 53
    Active Bin * Check Supply Levels Note: Menu Lockout does NOT prevent access to the Busy/Waiting Menu Group. This message will be displayed when the printer has determined that the paper length is too short to print the data as formatted. The following actions can be taken while this message is
  • Lexmark 13P0150 | Service Guide - Page 54
    Service will be required to fix the problem. The following action can be taken while this message is displayed: * Press Go to clear the error. The following Warning message may be displayed: Service Printer Waiting Menu. * Cancel Job * Reset Printer * Reset Active Bin * Check Supply Levels Note: Menu
  • Lexmark 13P0150 | Service Guide - Page 55
    you can: * Delete fonts, macros and other data in RAM * Install additional printer memory * Press Menu> or Menu< to access the Busy/ Waiting Menu Group. Held Jobs May Not be Restored These messages may be displayed when the printer has attempted to Print and Hold jobs from the disk and found that
  • Lexmark 13P0150 | Service Guide - Page 56
    the printer detects a defective flash. The following actions can be taken while this message is displayed: * Press Go to clear the message The flash will marked as bad and normal operation will continue. No flash operation will be allowed until the flash problem is resolved. 2-36 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 57
    Active Bin * Check Supply Levels Note: Menu Lockout does NOT prevent access to the Busy/Waiting Menu Group. This message will be displayed when the printer detects an unformatted flash at POST. The following actions can be taken while this message is displayed: * Press Go to clear the message. The
  • Lexmark 13P0150 | Service Guide - Page 58
    If you still have a problem go to the Serial Port Service Check. These messages may be displayed when data is sent to the printer across a serial port, Menu Group. The following functions may be available: * Reset Printer * Reset Active Bin * Check Supply Levels Note: Menu Lockout does NOT prevent
  • Lexmark 13P0150 | Service Guide - Page 59
    the port has been disabled. Note: Once the error has been displayed for the first time, reporting of further errors will be suppressed until the printer is reset or menus are entered. The following actions can be taken while this message is displayed: * Press Go to clear the message. Any data
  • Lexmark 13P0150 | Service Guide - Page 60
    or Hot Unplug the option. This message will be displayed when the printer detects a defective disk. This error may occur at power on, or to clear the message. The disk will be marked as defective and normal printer operation will continue. Disk operations will not be allowed with a defective disk and
  • Lexmark 13P0150 | Service Guide - Page 61
    Active Bin * Check Supply Levels Note: Menu Lockout does NOT prevent access to the Busy/Waiting Menu Group. This message will be displayed when the printer detects an unformatted disk at POST. The following actions can be taken while this message is displayed: * Press Go to clear the message. The
  • Lexmark 13P0150 | Service Guide - Page 62
    be displayed when the engine has detected that the fuser is missing. The following actions can be taken while this message is displayed: * Turn the printer off and insert the fuser assembly. 2-42 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 63
    , and the IPDS emulation will be disabled. No other printer functions will be affected. The correct IPDS emulation must be downloaded. Service Checks Cartridge Drive Assembly Service Checks • Black Cartridge Drive Assembly Error Codes associated with this Service Check: 150, 156 and 162 • Magenta
  • Lexmark 13P0150 | Service Guide - Page 64
    incorrect motor is detected. Replace the Magenta Cartridge Drive Assembly. Go to "Cartridge Drive Motor Assembly (Cyan, Magenta, Black)" on page 4-27. Perform "Automated Motor Detection" on page 3-16. Does the printer display Error Code 163? Yes Go to step 2 No Problem Solved 2-44 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 65
    still being displayed? Error Code 151 Error Code 157 Yes Call your next level support No Problem Solved Step 1 2 3 4 5 Actions and Questions Error Codes 151 and 157. These error codes indicate that the Magenta Cartridge Drive Motor has either failed to lock or has lost lock. Check the Magenta
  • Lexmark 13P0150 | Service Guide - Page 66
    Drive Assembly. Does this fix the problem? Replace the Engine Board. Does this fix the problem? Problem Solved Problem Solved No Install the cable correctly Install the cable correctly Replace the Cyan Cartridge Assembly Cable Go to step 5 Call your next level support 2-46 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 67
    being displayed? Yes Go to step 2 Call your next level support No Problem Solved Problem Solved Error Code 153 Error Code 159 Step 1 2 3 4 5 Actions and Questions Error Codes 153 and 159. These error codes indicate that the Yellow Cartridge Drive Motor has either failed to lock or has lost lock
  • Lexmark 13P0150 | Service Guide - Page 68
    Fan Disconnected Fan Switch On +3.3 V dc 0 V 0 V +24 V dc Error Code 926 VTB Fan Service Check Fan Disconnected Fan Switch Off +3.3 V dc 0 V +2 V dc * +24 V dc Step 1 2 Actions and Questions Turn the power off and manually spin the fan and check that it rotates freely. Does the fan rotate freely
  • Lexmark 13P0150 | Service Guide - Page 69
    dc Fan Disconnected Fan Switch On +3.3 V dc 0 V 0 V +24 V dc Error Code 927 RIP Fan Service Check Fan Disconnected Fan Switch Off +3.3 V dc 0 V +2 V dc * +24 V dc Step 1 2 3 Actions and Questions Turn the power off and manually spin the fan and check that it rotates freely. Does the fan rotate
  • Lexmark 13P0150 | Service Guide - Page 70
    this service check turn the printer on Service Check" on page 2-50 No Go to the "DC Power Service Check" on page 2-51 AC Power Service Check The printer the printer is receiving main AC power. Is the printer receiving Service Check" on page 2-51 No Inform the customer that AC power to the printer
  • Lexmark 13P0150 | Service Guide - Page 71
    Service Check The machine is partially operative, a motor turns, display is on or the Power On LED may be on or off. Step 1 2 3 Actions and Questions Does the printer the "Operator Panel LCD/ Status LED/ Buttons Service Check" on page 2-77 Go to Step 3 Problem Solved No Go to Step 2 Replace the "
  • Lexmark 13P0150 | Service Guide - Page 72
    following problems occur go to the Print Quality Service Check • A problem with only one color • Light or very light print CAUTION: Make sure the printer is - Call your next level of support. None of these parts are service related parts. Is there any problem see with the associated hardware?
  • Lexmark 13P0150 | Service Guide - Page 73
    as necessary. If this does not correct the problem, contact your next level support. Output Expander Service Check No Go to step 8 Replace the FRU selected. Paper exits half way out of the redrive. Yes Go to "Printer does not recognize that one or more output options as being installed." on page
  • Lexmark 13P0150 | Service Guide - Page 74
    No indication that Bin X is full OR No indication that Bin X is near full. 990 Service - Bin X Yes Go to "Remove paper Output Bin X is displayed, POST is incomplete that Bin X is near full." on page 2-59 Go to "990 Service - Bin X" on page 2-59 No Go to Step 4 Go to Step 5 Go to
  • Lexmark 13P0150 | Service Guide - Page 75
    the Autoconnect system on the Output Expander Option, base printer and check cables and connections to the Engine Board. Go to Step 4 Reseat the cables The problem is in the base printer. Check autoconnects in the printer. Replace the Output Expander Option Mechanical Linkage Assembly. Diagnostic
  • Lexmark 13P0150 | Service Guide - Page 76
    and other linkage parts for correct operation and any signs of wear, broken teeth or damaged parts. Are there any problems with these parts? Yes Repair or replace as necessary Replace the Mechanical Linkage/DC Motor Drive Assembly No Go to Step 2 Call your next level support 2-56 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 77
    operate correctly? Yes Replace the flag or repair as necessary No Go to Step 2 Call your next level support Replace the sensor assembly. If this does not fix the problem replace the "Engine Board" on page 4-13. 271 Paper Jam - Check Bin X, POST Incomplete. Step 1 2 3 4 Actions and Questions
  • Lexmark 13P0150 | Service Guide - Page 78
    Check Bin X, Post Complete, first sheet of paper feeds into Output Bin X. Note: Before proceeding with this service check run the Output Bin X Sensor Test and check for the failing sensor. Sensor Tests: XNF=Near Full Assembly Go to Step 4 Replace the Output Expander Control Board 2-58 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 79
    voltages correct? Yes Go to step 2 Go to step 3 Replace the sensor No Install the cable correctly Call your next level support Replace the Control Board 990 Service - Bin X Step 1 Actions and Questions Mechanical Linkage/DC Motor Assembly - Check the DC motor cable connector to make sure it is
  • Lexmark 13P0150 | Service Guide - Page 80
    Bin X Full - No message that Bin X is full displays Yes Go to "Problems with excessive static electricity buildup." on page 2-61 Go to "The printer does not recognize one or more output options as installed." on page 2-61 Go Go to Step 4 Go to Step 5 Go to Step 6 Go to Step 7 2-60 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 81
    Go to "990 Service Error Displays" on page 2-65 No Go to Step 8 Go to Step 9 Call your next level support Problems with excessive static 2. Replace the cover assembly if the ESD brush is loose or damaged The printer does not recognize one or more output options as installed. Note: If more
  • Lexmark 13P0150 | Service Guide - Page 82
    the Autoconnect cable Go to Step 4 Go to Step 5 Replace the Output Expander Option System Board No Check the autoconnect system in base printer Go to Step 3 Reseat the cables Check the Autoconnects in the printer Replace the Output Expander Option Mechanical Linkage Assembly 2-62 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 83
    Top Pass Thru Sensor Flag - Check the top sensor flag for correct operation, binding, broken parts or interference from the sensor cable. Are there any problem with the sensor flag? Top Pass Thru Sensor - Check to make sure the top pass thru sensor is correctly connected to J11 on the Control
  • Lexmark 13P0150 | Service Guide - Page 84
    ? Bin X Sensor Flag - Check the Bin X sensor flag for binding and proper operation. Are there any problems with the sensor flag? Bin X Sensor Cable continuity - Check the continuity of the sensor cable. Is there sensor cable correctly Go to Step 4 Replace the Bin X Cable 2-64 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 85
    Yes Replace the Bin X Sensor. If this does not fix the problem replace the Control Board. No Repair or replace as necessary Paper does not Solenoid Assembly Replace the 5 Bin Mailbox Control Board Assembly 990 Service Error Displays Step 1 Action and Questions Mechanical Linkage/DC Motor
  • Lexmark 13P0150 | Service Guide - Page 86
    to help isolate the problem. An incorrect printer driver, for the installed software, can cause print quality problems. Incorrect characters could print and the copy may not fit the page correctly. Note: Some 201 Paper Jam errors can be caused by a faulty print cartridge. 2-66 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 87
    and run the print test. Does the problem still exist for the remaining cartridges? Yes Replace the Cartridge Go to Step 3 Replace the Yellow Print Cartridge No Call your next level support Replace the failing cartridge Replace the Magenta Print Cartridge Blank Page (No Image) If there is
  • Lexmark 13P0150 | Service Guide - Page 88
    been removed and the cartridge is seated correctly? Print Cartridge - The cartridge may be out of toner or have another toner problem. Install a new toner cartridge. Does a new toner cartridge fix the problem? Yes Problem Solved Problem Solved No Go to Step 2 Go to Step 3 2-68 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 89
    position? Yes Replace the Retraction Motor. If this does not correct the problem, replace the "Engine Board" on page 4-13. No Replace the Cartridge Check - The toner may be out, the toner cartridge seated improperly or the shutter has been left on the bottom of the cartridge. Is the toner cartridge
  • Lexmark 13P0150 | Service Guide - Page 90
    the spring bent or damaged? Yes Problem Solved Repair the HV Contact Block problem in the print cartridge. Replace the print cartridge. A problem Cartridge Check - Try a new print cartridge. Doe a new print cartridge fix the problem in the print cartridge. Replace the black print cartridge. If there
  • Lexmark 13P0150 | Service Guide - Page 91
    a time and run a Test Page to help isolate the faulty print cartridge. Have you isolated the failing print cartridge? Yes Replace the faulty Print Cartridge No Run another test page after removing each print cartridge to isolate the problem. Low Image Density Note: If all colors have a low image
  • Lexmark 13P0150 | Service Guide - Page 92
    problem continues, replace the "ITU Assembly" on page 4-40. Transparency print quality is poor Step 1 Action and Questions Transparencies - Check the type or transparency being used. Is the transparency type being used recommended? Yes Go to Step 2 No Inform the customer 2-72 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 93
    5 Problem Solved Problem Solved No Go to Step 4 Replace the "Fuser" on page 4-15 Replace the "Second Transfer Roll" on page 4-41 Go to Step 6 Replace the "Second Transfer Roll" on page 4-41 Residual Image If only one color has a residual image repeated every 95mm, replace the print cartridge. If
  • Lexmark 13P0150 | Service Guide - Page 94
    assembly. Step 1 Action and Questions Print Cartridge(s) - This is most likely caused by a failure of the cleaner in the print cartridge or cartridges. Replace any of the cartridges that appear to have a problem. Does this fix the problem? Yes Problem Solved No Go to Step 2 2-74 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 95
    HV contact Assembly Developer Pin Springs Replace the Check the developer pin springs for the cartridge that is damaged having a problem to make sure they are no bent or Developer damaged. Spring Are the springs bent or damaged? No Repair the HV Block Contact for the
  • Lexmark 13P0150 | Service Guide - Page 96
    5060-XXX Step 2 Action and Questions Cartridge Check - The cartridge may be out of toner or have another toner problem. Try a new toner cartridge. Does a new toner cartridge fix the problem? Yes Problem Solved No Call your next level support Toner smears or rubs off the page with no error code
  • Lexmark 13P0150 | Service Guide - Page 97
    caused by a cleaner problem in the print cartridge. Replace the print cartridge. All the colors streaking Problem Solved Replace the failing Printhead. Go to "Printheads" on page 4-33. No Go to Step 2 Call your next level support Operator Panel LCD/Status LED/Buttons Service Check Use this service
  • Lexmark 13P0150 | Service Guide - Page 98
    Is the operator panel assembly completely blank and the Power on Status LED On? 6 Does the printer Beep 5 times? Yes Go to step 2 Problem Solved Replace the "Operator Panel" on page 4-25 Go to step 6 Go to step 10 Go Panel" on page 4-25 and replace the operator panel cable 2-78 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 99
    Replace the "RIP Board" on page 4-11 Go to the "Operator Panel" on page 4-25 and replace the operator panel cable Call your next level support Go to step 14 Go to the "Operator Panel" on page 4-25 and replace the operator panel cable Diagnostic Information 2-79
  • Lexmark 13P0150 | Service Guide - Page 100
    Fuser Service Check 3 Cold Fuser Service Check If error code 122,123,126,127,128,129,130, 131, 132 or 133 is displayed, the printer detects a problem in the fuser shown: 1. "Fuser" on page 4-15 If this does not fix the problem replace: 2. "Engine Board" on page 4-13 Error Code 129 Fuser Backup
  • Lexmark 13P0150 | Service Guide - Page 101
    5060-XXX Error Code 130 Hot Roll did not reach the correct standby temperature. Step 1 2 Action and Questions Voltage Check - Go to "Engine Board" on page 5-1. Measure the voltage on connector J10-11. The voltage measures approximately .13 V dc to .64 V dc as the hot roll lamp turns off and on.
  • Lexmark 13P0150 | Service Guide - Page 102
    of the fuser frame assembly. Check to make sure the lamp is not broken, cracked or open. Is there a problem with the lamp or its installation? Yes Replace the "Fuser" on page 4-15 Reinstall the lamp. Replace as necessary. ? Yes Go to step 2 No Replace the "Fuser" on page 4-15 2-82 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 103
    4-15 Replace the following FRU's in order: 1. "LVPS" on page 4-14 2. "Engine Board" on page 4-13 Hot Fuser Service Check Error codes 124, 125, 134, and 135 display whenever the printer detects a problem with the fuser running over temperature or the fuser lamps have been on too long. Error Code 124
  • Lexmark 13P0150 | Service Guide - Page 104
    the "Automated Motor Detection" on page 3-16. Does the printer continue to display error code 161? Yes Call your next level support No Problem Solved Error Code 149 Error Code 155 Step 1 2 Action and page 4-16 No Correctly install the cable Replace the "Fuser" on page 4-15 2-84 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 105
    ? Is Paper Jam 201 displayed? Yes Go to step 2 No Install the cable correctly Go to the "2XX Paper Jam Message Table" on page 2-19 Problem Solved Diagnostic Information 2-85
  • Lexmark 13P0150 | Service Guide - Page 106
    Paper Jam Message Table" on page 2-19 Go to the "Paper Path Service Check" on page 2-97 Error Code 930 This type of problem with the fuser circuits is usually associated with the zero crossover signal from the 1. "LVPS" on page 4-14 2. "Engine Board" on page 4-13 Problem Solved 2-86 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 107
    5060-XXX Cover Open/HV Interlock Switch Service Check "Close Door" is displayed constantly, unable to clear the message from the display, POR incomplete. Step 1 2 3 4 5 6 Action and Questions Front Cover and HV Interlock
  • Lexmark 13P0150 | Service Guide - Page 108
    to step 2 Go to step 3 Replace the "PSD Sensor Assembly" on page 4-34. If this does not correct the problem, replace the "RIP Board" on page 4-11. Whenever the the PSD assembly is replaced it is necessary to perform all the cable correctly Replace the "RIP Board" on page 4-11 2-88 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 109
    No Replace the PSD cable for the Cyan and Yellow PSD Assemblies Tray 1 Paper Size Sensing Service Check The printer does not sense the size of the media installed in Tray 1. Note: If there is a problem when installing Tray 1, Tray 1 is difficult to remove or does not stay locked in position, go
  • Lexmark 13P0150 | Service Guide - Page 110
    as necessary Tray 1 Service Check Tray 1 does not stay seated or fit correctly in the printer, the media fails to feed correctly from Tray 1 or Tray 1 is difficult to install Note: The Tray 1 Feed Test in the CE Diagnostics can be used to help isolate problems Service Manual
  • Lexmark 13P0150 | Service Guide - Page 111
    is out or low, go to "Step D" on page 2-93. If the printer fails to detect transparencies and 203 Paper Jam displays, go to "Step E" on page 2-94. Note: When feeding paper through the printer to check for autocompensator problems use the Tray 1 Feed test in the CE Diagnostics as a printed copy is
  • Lexmark 13P0150 | Service Guide - Page 112
    the Autocompensator Assembly Step C Step 1 2 Action and Questions Can you remove Tray 1 from the printer? Open the Lower Jam Access door and carefully lift the autocompensator assembly until it is in it's is causing the tray to stay in a locked position. Repair as necessary 2-92 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 113
    the Input Tray Tests menu. You can activate the Paper Level Sensor inside the printer. The Paper Level Sensor is a dual sensor and checks the following levels correctly and the flag not broken or damaged? Yes Call your next level support Repair or replace parts as necessary Go to step 4 Go to step
  • Lexmark 13P0150 | Service Guide - Page 114
    not correct the problem, replace the" printer is unable to feed a sheet from the MPF paper tray or is jammed before at or over the input sensor. Step 1 Action and Questions Does media feed correctly from Tray 1? Yes Go to step 2 No Go to "Tray 1 Service Check" on page 2-90 2-94 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 115
    of the parts broken, damaged or missing? 5 Manually turn the MPF Drive Gear in the MPF printer is Call your next matching up properly with the MPF Drive Gear in the MPF level support Tray assembly. Do the gears match up correctly? No Go to step 3 Go to the "Autocompe nsator Service
  • Lexmark 13P0150 | Service Guide - Page 116
    necessary Determine what is causing the paper to jam prior to the input sensor. If unable to determine what is causing the problem, call your next level support. No Install the cable correctly Install the cable correctly Replace the "Engine Board" on page 4-13 Replace the Sensor Cable Assembly Go
  • Lexmark 13P0150 | Service Guide - Page 117
    the "Multipurpose Feeder (MPF) Service Check" on page 2-94. 200 cartridges and ITU assembly to gain access to the inside of the printer input area of the printer. Were any problems found inside the printer? Check to make Plate correctly Call your next level support 201 Paper Jam Displayed - Unable
  • Lexmark 13P0150 | Service Guide - Page 118
    the front paper jam door. Remove all the print cartridges. Remove the vacuum transport assembly and check for on the vacuum transport belts as it passes through the printer? Yes Go to Step 3 Remove the media from Step 6 Go to Step 7 Contact your next level support No Go to Step 5 Go to Step 4 Go
  • Lexmark 13P0150 | Service Guide - Page 119
    Go to step 2 Go to step 3 Replace the "Fuser" on page 4-15 Replace the "Fuser" on page 4-15 Go to step 6 Call your next level support Replace the "Redrive Assembly" on page 4-35 No Replace the Vacuum Transport Assembly Go to Step 4 Replace the "Fuser" on page 4-15 Go to step
  • Lexmark 13P0150 | Service Guide - Page 120
    5060-XXX 2-100 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 121
    Diagnostic Aids This chapter explains the tests and procedures to identify printer failures and verify repairs have corrected the problem. To run the printer diagnostic tests described in this chapter, you must put the printer in Diagnostic Mode. Diagnostic Mode To enter the Diagnostic Mode: 1. Turn
  • Lexmark 13P0150 | Service Guide - Page 122
    disk cannot be recovered because too many bad blocks exist on the disk. 4. Press Go or Return/Stop to return to the Device Tests menu. 3-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 123
    the menu. 2. Select Single or Continuous. - The single Duplex Quick test cannot be canceled. The printer attempts to print the Quick Test Page from the default paper source. If the default paper source only supports envelopes, then the page is printed from Tray 1. Check the Quick Test Page for the
  • Lexmark 13P0150 | Service Guide - Page 124
    Viewing the Error Log The error log provides a history of printer errors. The error log contains the 12 most recent errors that have occurred on the printer. The most recent error displays in position 1 and the oldest on the screen. 3. Press Return/Stop to exit the Clear Log menu. 3-4 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 125
    5060-XXX Hardware Tests The following Hardware Tests can be selected from this menu: LCD Test Button Test DRAM Memory Test ROM Memory Test Parallel Wrap (if available) Serial Wrap (if available) Serial 1 Wrap (if available) Serial 2 Wrap (if available) Serial 3 Wrap (if available) LCD Test To run
  • Lexmark 13P0150 | Service Guide - Page 126
    (P/N 1319128). 2. Select the Parallel Wrap Test from the menu. - The power indicator blinks indicating the test is in progress. The test runs continuously until canceled. 3-6 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 127
    5060-XXX Each time the test finishes, the screen updates. If the test passes, the Pass Count increases by 1, however if the test fails, one of the following messages displays for approximately three seconds: Sync Busy Error Byte Interrupt Request Error Strobe Interrupt Request Error Init Fail Error
  • Lexmark 13P0150 | Service Guide - Page 128
    the paper path as media is feeding through the printer. The upper front door, used to access the print cartridge, cannot be opened during the feed test. To can be run using any of the paper or envelope sizes supported by the printer. The pages are placed in the default output bin, however, the
  • Lexmark 13P0150 | Service Guide - Page 129
    P=Input Tray Pass Thru Sensor 2. Once this message displays, you can manually actuate each sensor. The tray empty sensor can be actuated by hand, however displays. 3. Press Return/Stop to exit the test. Tray sensors are supported by the following sources: L1 L2 Yes Yes Yes Yes Yes Yes
  • Lexmark 13P0150 | Service Guide - Page 130
    SC=input trays side cover sensor Manually actuate the bin sensor by moving the Standard Bin/Full=CL" message displays. Manually actuate the bin sensor by moving the Bins" printer setting is link rather than mailbox, the printer selects All output bins installed on the printer are shown on the feed
  • Lexmark 13P0150 | Service Guide - Page 131
    are working correctly. The following Output options, if installed, are supported by this test. Standard Bin Output Expander High Capacity Output L=FL indicates the bin is full. 3. Once the screen is displayed you can manually actuate the sensor you want to test. When the sensor is closed (CL)
  • Lexmark 13P0150 | Service Guide - Page 132
    of dual sensor) NF = Near Full Sensor (upper part of dual sensor) Once the message displays, you can manually actuate each of the output bin sensors. For all the sensors except the output level sensor, when the sensor is near full or full L = NF bin is near full L = FL bin is full 3-12 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 133
    S1 * Input Sensor S2 * Inline Media Sensor * Fuser Exit Sensor To run the Base Printer Sensor Test. 1. Select Base Printer Sensor Test from the menu. - The operator panel displays OP for open and CL for closed. 2. Manually toggle the sensors by hand to verify that each sensor switches from open to
  • Lexmark 13P0150 | Service Guide - Page 134
    menu. 2. Select a destination bin. The printer feeds eight pieces of media to the selected test is complete the printer returns to the original screen correctly. The following sensors are supported by this test: * is displayed: Staple C=CL SL=CL C=Cartridge Presence Sensor SL=Staple Low Sensor If you
  • Lexmark 13P0150 | Service Guide - Page 135
    following is displayed. Bin Level Sensor NF=OP NF=Finisher Bin Near Full Sensor. 3. Once the selected screen is displayed the selected sensor can be manually actuated. CL is displayed when the sensor is closed. OP is displayed when the sensor is open. 4. To exit the test press Return or Stop
  • Lexmark 13P0150 | Service Guide - Page 136
    . Tests from the menu. 2. Select Motor Detect from the menu. 3. Remove all the print cartridges from the printer. 4. Press Go. The following screen is displayed: Motor Detection in progress The test lasts approximately then the envelope print test pattern is printed on the 3-16 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 137
    is installed with a Machine Class ID which matches the Machine Class ID stored in the printer NVRAM. When printed from the Diagnostic Test Menu the toner cartridge lockout function is disabled. To run the Print Quality Test page from the Diagnostic menu, select Print Quality Test Pages from
  • Lexmark 13P0150 | Service Guide - Page 138
    Test Printing" message displays. Once printing is complete, the Registration screen displays. The "Quick Test Page" should be printed on letter or A4 paper. 3-18 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 139
    7 in 0.5 increments (0*). 5. Press Select to continue to the next alignment value. 6. To cancel the alignment procedure press Go or Return. Setting Printer Alignment 1. Enter the Diagnostic Mode. 2. Select Alignment for Cyan, Yellow, or Magenta. The following screen is displayed: T=sxx* R=sxx* L=sxx
  • Lexmark 13P0150 | Service Guide - Page 140
    should be printed on A4 or Letter paper. The printer tries to print the test page from the default paper source, however if the default source only supports envelopes, then the page ,prints from Tray 1. On Off N/A Standalone Feeding Operation Mode On On On N/A Not used 3-20 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 141
    (ESD). To prevent damage to ESD-sensitive parts, follow the instructions below in addition to all the usual precautions, such as turning off to perform the "Printhead Manual Adjustment" on page 4-1 and "Printhead Electronic Alignment" on page 4-4. Printhead Manual Adjustment 1. Draw a scribe
  • Lexmark 13P0150 | Service Guide - Page 142
    5060-XXX 2. Position the printhead along the front (A) and rear (B) scribe lines. 3. Run an Alignment Test Page from "Setting Printer Alignment" on page 3-19. 4-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 143
    to verify the printhead front adjustment. Note: You may be required to make both front and rear printhead adjustments several times to obtain correct manual alignment on both sides of the Alignment Test Page. 8. After you obtain correct front and rear printhead adjustments, tighten the left rear
  • Lexmark 13P0150 | Service Guide - Page 144
    to Cartridge Attach 4 Guides Front Cover Pivot to Front Attach 2 Upper Cover Front Left Light Shield to Upper Front Cover Attach 1 121 M3.5x6mm LVPS to Lower Frame Mounting 7 Machine Right Rear Cover to LVPS Attach 1 HVPS standoffs to Upper Attach 4 Frame 4-4 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 145
    Screw type Location Purpose Qty 232 M3x6mm Taptite Ground Cable to Right Front Attach 2 Metal Thread Cover Support and Upper Forming Frame. Ground Cable to Bottom Attach 2 Support Plate and Engine Card Shield Back Lamp Brackets to Fuser Attach 2 Frame Front Lamp Brackets to Fuser
  • Lexmark 13P0150 | Service Guide - Page 146
    1 MPF Latch Support Brackets Attach 2 to Upper Frame Voltage Cable to Terminal Attach 1 (BOR/ITU) Black Voltage Cable to Terminal Attach 1 (BOR/ITU) Cyan Voltage Cable to Terminal Attach 1 (BOR/ITU) Magenta Voltage Cable to Terminal Attach 1 (BOR/ITU) Yellow 4-6 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 147
    Frame Door Latch Catch to Frame Attach 2 Transfer HVPS to Lower Frame Mounting 1 Fuser Top Duct to Lower Frame Attach 1 Right Front Cover Support to Attach 1 Lower Frame Front Lower Left Cover to Attach 1 Lower Frame Front Left Handle Cover Asm Attach 4 to Lower Frame Front Lower
  • Lexmark 13P0150 | Service Guide - Page 148
    Shield Attach 1 ITU Light Shield Asm to Upper Attach 1 Front Guide ITU Ribs to Upper Redrive Door Mounting 5 Upper Door Hinges to Redrive Asm to Upper Frame (Redrive) Mounting 2 Developer HVPS to Cartridge Mounting 4 Contact Asm Engine Card Shield to Frame Mounting 5 4-8 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 149
    Left Light Shield to Left Attach 1 Upper Cover Asm and Top Cover Front Right Light Shield to Attach 1 Right Front Cover Support and Top Cover Cartridge Drive Assemblies to Mounting 12 Upper Frame Upper Door Hinges to Upper Attach 2 Frame (Redrive) Inner Redrive Assembly to Upper Frame
  • Lexmark 13P0150 | Service Guide - Page 150
    to avoid pinching wires, obstructing the paper path, or restricting mechanical movement. Outer EMC Shield 1. Loosen screws (A) and lift the outer EMC shield from the printer. 4-10 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 151
    5060-XXX RIP Board 1. Remove the "Outer EMC Shield" on page 4-10. 2. Remove the "Left Rear Cover" on page 4-11. 3. Remove the USB connector screw type "232" on page 4-5 (A). 4. Remove the RIP board screw type "232" on page 4-5 (B). 5. Disconnect all cables from the RIP board and remove the board.
  • Lexmark 13P0150 | Service Guide - Page 152
    1. Remove the "Left Rear Cover" on page 4-11. 2. Remove the rear fan cover screw type "323" on page 4-7 (A) and remove the rear fan cover. 4-12 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 153
    5060-XXX Main Fan 1. Remove the "Rear Fan Cover" on page 4-12. 2. Disconnect the main fan cable from connector J2 (B) on the engine board. 3. Remove the main fan screws (A), part number 12G6529 and remove the fan. Engine Board 1. Remove the "Rear Fan Cover" on page 4-12. 2. Remove the "Left Rear
  • Lexmark 13P0150 | Service Guide - Page 154
    5060-XXX LVPS 1. Remove the "Rear Fan Cover" on page 4-12. 2. Remove the "Fuser" on page 4-15. 3. Remove the LVPS screw type "121" on page 4-4 (A) from the rear of the printer. 4. Remove the right rear cover screw type "121" on page 4-4 (A). 4-14 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 155
    -XXX 5. Open the redrive cover and remove the screw type "121" on page 4-4 (A) from the top of the LVPS and remove the LVPS from the printer. Fuser CAUTION: Be sure the fuser assembly has cooled before you remove it. 1. Open the fuser access cover. 2. Unlatch the two fuser latches (A). 3. Remove the
  • Lexmark 13P0150 | Service Guide - Page 156
    1. Open the fuser access cover. 2. Carefully flex the fuser access cover to free the hinges from the mounting posts. 3. Remove the fuser access cover. 4-16 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 157
    5060-XXX Fuser Top Duct 1. Remove the "Rear Fan Cover" on page 4-12. 2. Remove the fuser top duct screw type "323" on page 4-7 (A,B) and remove the top duct. Fuser Bottom Duct 1. Remove the "Fuser Top Duct" on page 4-17. 2. Remove the "Main Fan" on page 4-13. 3. Press the fuser bottom duct latches
  • Lexmark 13P0150 | Service Guide - Page 158
    5060-XXX Fuser Web Oiler Motor Assembly 1. Remove the "Fuser" on page 4-15. 2. Remove the paper path access door cover right mounting screw. 3. Remove the "Front Right Handle Cover Assembly" on page 4-28. 4. Disconnect the web oiler motor assembly cable. 4-18 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 159
    assembly. Note: When you reinstall the web oiler motor assembly, pull the excess cable, twist, install a cable tie, and route the cable down into the printer. Note: Make sure the motor cable is routed away from gears (B). Repair Information 4-19
  • Lexmark 13P0150 | Service Guide - Page 160
    . 2. Remove the detent post tension spring (B). 3. Flex the front cover assembly to free the hinge from the mounting post (A). 4. Remove the front cover assembly. 4-20 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 161
    5060-XXX Top Cover 1. Remove the "Front Cover Assembly" on page 4-20. 2. Remove the "Redrive Door" on page 4-20. 3. Remove the redrive cap. 4. Remove the light shield screw type "324" on page 4-9 and "323" on page 4-7 (A). 5. Remove the shield. Repair Information 4-21
  • Lexmark 13P0150 | Service Guide - Page 162
    5060-XXX 6. Remove the front upper pivot cover screw (A) and remove the pivot cover. 7. Open the MPF and remove the top cover mounting screw (B) from the left side of the printer. 8. Remove the top cover mounting screw (A) from the rear of the printer. 4-22 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 163
    5060-XXX 9. Remove the top cover mounting screws (A) from the front of the printer. 10. Remove the operator panel bezel. 11. Open the redrive door and loosen the redrive assembly screw type "323" on page 4-7 (A). Repair Information 4-23
  • Lexmark 13P0150 | Service Guide - Page 164
    5060-XXX 12. Lift the top cover and disconnect the operator panel cable. 13. Remove the bin full sensor (C), flag (A), and upper options auto connect (B) from the top cover. 14. Remove the top cover. 4-24 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 165
    5060-XXX Operator Panel 1. Remove the "Front Cover Assembly" on page 4-20. 2. Remove the operator panel bezel. 3. Unlatch the operator panel latches (A). Repair Information 4-25
  • Lexmark 13P0150 | Service Guide - Page 166
    operator panel. Cartridge Drive Motor Assembly (Yellow) 1. Remove the "Rear Fan Cover" on page 4-12. 2. Remove the cartridge drive motor assembly mounting screws (A). 3. Disconnect the cable from the cartridge drive motor assembly. 4. Remove the cartridge drive motor assembly. 4-26 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 167
    Remove the "RIP Card Shield Assembly" on page 4-36. 2. Remove the "Engine Board" on page 4-13. 3. Remove the cartridge drive motor assembly mounting screws (A). 4. Disconnect the cable (B) from the cartridge drive motor assembly. 5. Remove the cartridge drive motor assembly. Repair Information 4-27
  • Lexmark 13P0150 | Service Guide - Page 168
    Cover/Front Lower Left Cover" on page 4-30. 5. Remove the front right handle cover assembly screw type "323" on page 4-7 (A) and remove the assembly. 4-28 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 169
    5060-XXX Front Left Handle Cover Assembly 1. Open the front cover. 2. Remove the front left handle cover assembly screw type "323" on page 4-7 (A) and remove the assembly. ITU Door 1. Remove the "Front Left Handle Cover Assembly" on page 4-29. 2. Remove the ITU door screw type "323" on page 4-7 (A)
  • Lexmark 13P0150 | Service Guide - Page 170
    remove the door. 3. Separate the paper path access door cover from the front lower left cover (C). Be careful not to lose the door spring (D). 4-30 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 171
    5060-XXX Multipurpose Feeder (MPF) 1. Open the MPF. 2. Remove the front MPF left upper pivot cover hinge screw type "323" on page 4-7 (A). 3. Remove the MPF strap screw type "412" on page 4-9 (A). 4. Disconnect the MPF switch cable from the engine board at connector J10. 5. Remove the MPF. Repair
  • Lexmark 13P0150 | Service Guide - Page 172
    5060-XXX Waste Container Access Door 1. Open the waste container access door. 2. Flex the door and remove it from the hinges (A). Left Lower Cover 1. Remove the "ITU Door" on page 4-29. 2. Remove the left lower cover screw type "323" on page 4-7 (A) and remove the cover. 4-32 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 173
    "Top Cover" on page 4-21. 2. Remove the printhead screw type "484" on page 4-9 (B) through the holes (A) in the top of the rear printer frame. 3. Remove the printhead mounting screw (A) from the front of the printhead assembly. 4. Disconnect the printhead cables (B) from the printhead. 5. Disconnect
  • Lexmark 13P0150 | Service Guide - Page 174
    page 4-21. 2. Remove the rip fan mounting screws (A). 3. Disconnect the rip fan cable from the engine board at connector J53. 4. Remove the rip fan. 4-34 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 175
    5060-XXX Redrive Assembly 1. Open the redrive door. 2. Remove the redrive assembly screw type "323" on page 4-7 (A). 3. Remove the drive belt (B) from the lower redrive pulley. 4. Remove the redrive assembly. Note: When you reinstall the redrive assembly be sure to align the notch in the redrive
  • Lexmark 13P0150 | Service Guide - Page 176
    shield assembly. HVPS Developer Board 1. Remove the "RIP Card Shield Assembly" on page 4-36. 2. Remove the HVPS developer board screw type "323" on page 4-7 (A). 4-36 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 177
    5060-XXX 3. Disconnect the HVPS developer board cables (B) and remove the board. VTB Fan 1. Remove the "RIP Card Shield Assembly" on page 4-36. 2. Remove the VTB fan with a flatblade screwdriver. Repair Information 4-37
  • Lexmark 13P0150 | Service Guide - Page 178
    , Magenta, Black)" on page 4-27 according to which cartridge drive assembly you are replacing. 2. Remove the cartridge drive assembly mounting screws (A), disconnect cable (B), and remove ITU drive motor assembly mounting screws (B), disconnect cable (A), and remove the assembly. 4-38 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 179
    5060-XXX Engine Board Shield 1. Remove the "Engine Board" on page 4-13. 2. Remove the engine board shield screw type "323" on page 4-7 (A), screw type "232" on page 4-5 (B), and remove the shield. Waste Toner Auger Assembly 1. Remove the "RIP Card Shield Assembly" on page 4-36. 2. Remove the "Engine
  • Lexmark 13P0150 | Service Guide - Page 180
    cartridges. 3. Open the MPF. 4. Press the ITU release lever (A) and slide the ITU from the printer. Waste Toner Latch 1. Remove the "Paper Size Sensor Assembly" on page 4-41. 2. Use a flatblade screwdriver to release the waste toner latch from the paper size sensor assembly. 4-40 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 181
    5060-XXX Paper Size Sensor Assembly Note: The paper size sensor assembly contains components that easily fall apart as you remove the assembly. Be careful not to lose any of the components. 1. Remove the "Left Rear Cover" on page 4-11. 2. Remove the "Rear Fan Cover" on page 4-12. 3. Remove the "
  • Lexmark 13P0150 | Service Guide - Page 182
    38. 2. Open the front cover. 3. Remove the toner cartridges. 4. Remove the cartridge rail front and rear mounting screws and remove the rail. 5. Disconnect the cable from the HVPS developer board. 6. Press the cartridge contact assembly retaining tabs (A) and remove the assembly. 4-42 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 183
    5060-XXX 5. Connector Locations Engine Board Connector J2 Main Fan J3 Oiler Stepper Motor J4 VTB Fan J5 Options Conn. Trays J7 Options Conn. Stacker Pin No. Signal 1 FAN1 Stall IN 2 Ground 3 FAN1 PWM Out 4 +24 V dc Left Side 1 Oiler PHA OUT + 2 Oiler PHB OUT + 3 Oiler PHA OUT - 4
  • Lexmark 13P0150 | Service Guide - Page 184
    IN 14 FUSER HALL IN 15 Y LOCK IN 16 FUSER LOCK IN 1 +3.3 V dc 2 +5 V dc 3 +5 V dc 4 +24 V dc 5 +24 V dc 6 Ground 7 Ground 8 Ground 9 Ground 10 Ground 5-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 185
    5060-XXX Connector J10 Fuser J11 Bin Full J12 ITU Lift Brush Pin No. Signal 1 EXIT SENSOR IN 2 FUSER CAM1 IN 3 FUSER CAM2 IN 4 OILER ENC A IN 5 OILER ENC B IN 6 HR THERM IN 7 BR THERM IN 8 Ground 9 +5 V dc switched 10 ZERO Xing IN 11 HR HEAT ON OUT 12 BR HEAT ON OUT 1 +5
  • Lexmark 13P0150 | Service Guide - Page 186
    12 M DEV PWM OUT 13 (-CART METER K IN) 14 C DEV PWM OUT 15 SC Y CHIP 16 Y DEV PWM OUT 17 Ground 18 +24 V dc switched 5-4 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 187
    5060-XXX Connector J45 RIP Interface Pin No. Signal 1 I2C DATA RIP 2 I2C CLK RIP 3 (-NOTIFY RIP) 4 Ground 5 (-VSYNC Y OUT) 6 FPIRQ RIP 7 (-VSYNC M OUT) 8 (-VSYNC C OUT) 9 Ground 10 (-VSYNC K OUT) 11 (-HSYNC Y IN) 12 (-HSYNC C IN) 13 (-HSYNC M IN) 14 (-HSYNC K IN) 15
  • Lexmark 13P0150 | Service Guide - Page 188
    IN 14 C HALL IN 15 M LOCK IN 16 C LOCK IN 1 CLR FULL IN 2 Ground 1 FAN3 STALL IN 2 Ground 3 FAN3 PWM OUT 4 +24 V dc Right Side 5-6 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 189
    5060-XXX Connector J64 ITU/K Cart J67 Staging Motor Pin No. Signal 1 K ON OUT 2 ITU ON OUT 3 +5 V dc 4 +5 V dc 5 K DIR OUT 6 ITU DIR OUT 7 +24 V dc ITU and K 8 +24 V dc ITU and K 9 Ground 10 Ground 11 K CLK OUT 12 ITU CLK OUT 13 K HALL IN 14 ITU HALL IN 15 K LOCK IN
  • Lexmark 13P0150 | Service Guide - Page 190
    PAPER LOW IN J70 MPF Media 4 Ground 5 LED VCC 6 Ground 7 +3.3 V dc 8 XPAR TRAY 1 IN 1 +5 V dc switched 2 MPF FEED LOW IN 3 MPF FEED OUT IN 4 Ground 5-8 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 191
    5060-XXX Connector J71 HVPS- Transfer J72 ITU Autoconnect Pin No. Signal 1 ITU TX ENA OUT 2 ITU TX CUR PWM 0 3 ITU SERVO INTO 4 ITU TX PWM OUT 5 CMY TX ENA OUT 6 K SERVO INTO 7 K TX PWM OUT 8 C SERVO INTO 9 C TX PWM OUT 10 Y SERVO INTO 11 Y TX PWM OUT 12 M SERVO INTO 13 M
  • Lexmark 13P0150 | Service Guide - Page 192
    5060-XXX Connector J73 Autocompensator Motor1 (+5 V dc switched) J86 Cover Interlock Engine Board Pin No. Signal 1 2 AUTOCOMP ENC IN 3 Ground 4 Ground 5 AUTOCOMP OUT 2 6 AUTOCOMP OUT 1 1 +24 V dc to Cover SW 2 +24 V dc switched 5-10 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 193
    5060-XXX RIP Board Connector J1 Operator Panel Connector J2 Printhead Yellow Connector J3 Printhead Yellow Connector Pin No. Signal 1 OP I2CDATA 2 +5 V dc 3 OP I2CClk 4 Ground 5 OP I2R- 1 Ground 2 HSYNC-/SOS 3 thermistor 4 +5 V dc Hsync 5 Ground 6 mm ref freq 7 mm lock 8
  • Lexmark 13P0150 | Service Guide - Page 194
    10 +24 V dc mir mtr 1 NC 2 NC 3 laser en 4 Ground 5 laser adj 6 Ground 7 laser PWM 8 +5 V dc head 9 Ground 10 video data - 11 video data + 5-12 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 195
    5060-XXX Connector J7 Printhead Magenta Connector J8 Printhead Magenta Connector J9 Printhead Magenta/Black Connector Pin No. Signal 1 Ground 2 HSYNC-/SOS 3 thermistor 4 +5 V dc Hsync DC 5 Ground 6 mm ref freq 7 mm lock 8 mm strt/en 9 Ground 10 +24 V dc mir mtr 1 NC 2 NC 3
  • Lexmark 13P0150 | Service Guide - Page 196
    Port Connector video data video data + +5 V dc Ground V Corx J18 USB Port Connector 1 2 3 4 G1 G1 G2 G2 USB +5 V dc USB DUSB D+ Ground Ground Ground 5-14 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 197
    5060-XXX Connector J19 Option DRAM Socket 2 J20 Option DRAM Socket 1 J21 Base DRAM Socket J23 Power Connector Pin No. Signal 1 Ground 2 Ground 3 Ground 4 Ground 5 Ground 6 Ground 7 Ground 8 Ground 9 +3 V dc Sense 10 +3.3 V dc 11 +3.3 V dc 12 +3.3 V dc 13 +5 V dc 14 +5 V
  • Lexmark 13P0150 | Service Guide - Page 198
    Y 8 HSYNCN C 9 Ground 10 VSYNCN K 11 VSYNCN M 12 VSYNCN C 13 VSYNCN Y 14 VSYNCN 15 OWL PIO NOTIFY R 16 Ground 17 OP I2DATA R 18 OP I2CLK R 5-16 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 199
    RIP Board 5060-XXX Connector Locations 5-17
  • Lexmark 13P0150 | Service Guide - Page 200
    12 +3.3 V dc 13 +5 V dc 14 +5 V dc 15 +5 V dc 16 +24 V dc 1 +3.3 V dc 2 +5 V dc 3 +5 V dc 4 +24 V dc 5 +24 V dc 6 Ground 7 Ground 8 Ground 9 Ground 10 Ground 5-18 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 201
    5060-XXX Connector Engine Board Cable Pin No. Signal 1 FusExitSen 2 BURCam1 3 N/C 4 WebEncoderA 5 WebEncoderB 6 HRThermistor 7 BURThermistor 8 Ground 9 +5 V dc switched 10 ZCSense 11 Heat On #1 12 Heat On #2x Connector Locations 5-19
  • Lexmark 13P0150 | Service Guide - Page 202
    Control Connector 1 AC Load #1 AC Common Ground NC AC Load #2x FusExitSen 2 BURCam1 3 N/C 4 WebEncoderA 5 WebEncoderB 6 HRThermistor 7 BURThermistor 8 Return - Analog Ground 9 +5 V dc switched 10 N/Cx 5-20 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 203
    5060-XXX High Capacity 2000-Sheet Board Connector Locations 5-21
  • Lexmark 13P0150 | Service Guide - Page 204
    1 HV Transformer Output Terminal to Cyan Transfer Cable 1 HV Transformer Output Terminal to Yellow Transfer Cable 1 HV Transformer Output Terminal to Magenta Transfer Cable 5-22 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 205
    HVPS Board 5060-XXX Connector Locations 5-23
  • Lexmark 13P0150 | Service Guide - Page 206
    Board Connector CN1 Developer HVPS Input CN2 Smart Cartridge Black CN3 Smart Cartridge Magenta CN4 Smart Cartridge Cyan CN5 Smart Cartridge Yellow CB Terminal Pin No Signal 1 CtSense 2 C-TnrSense (Gnd Return) 1 Y-CtSense 2 Y-TnrSense (Gnd Return) Cleaner Bias Terminal 5-24 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 207
    5060-XXX HVPS Developer Board Connector Locations 5-25
  • Lexmark 13P0150 | Service Guide - Page 208
    5060-XXX 5-26 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 209
    printer preventive maintenance. Following these recommendations can help prevent problems and maintain optimum performance. Safety Inspection Guide The purpose of this inspection guide • Possible safety exposure from any non-Lexmark attachments Lubrication Specifications Lubricate only when parts
  • Lexmark 13P0150 | Service Guide - Page 210
    copies when the ITU Assembly needs to be replaced to maintain the print quality and reliability of the printer. There are two assemblies, ITU assembly and Second Transfer Roll, in a maintenance kit. Both should be count must be reset to zero to clear the maintenance message. 6-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 211
    not pictured in the illustration. • PP: (Parts Packet) in the Description column indicates the part is contained in a parts packet. The Lexmark C750 (5060-XXX) laser printer is available in three models: 5060-001 5060-002 5060-003 The parts catalog uses these designations to identify model specific
  • Lexmark 13P0150 | Service Guide - Page 212
    Assembly 1: Covers 5060-XXX 7-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 213
    1 Cable, Options - Stacker 1 Redrive Cap Cover Assembly 1 Top Front Support Bracket 1 Right Rear Cover 1 Screw, PP 12G6530 1 Right Lower Door Pivot Cover 2 Screw, PP 12G6532 1 Front Access Door Support 1 Paper Tray Guide 1 Machine Pad 1 Jam Access Door Spring 1 Front Hold
  • Lexmark 13P0150 | Service Guide - Page 214
    Assembly 1.1: Covers 5060-XXX 7-4 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 215
    5060-XXX Assembly 1.1: Covers AsmIndex 1.1-1 2 3 4 5 6 7 8 9 10 11 NS NS NS NS NS NS NS NS NS NS Part number 12G6408 12G6392 12G6398 12G6395 12G6400 12G6390 12G6401 12G6340 12G6358 12G6360 12G6339 12G6510 12G6511 12G6485 12G6386 12G6387 12G6383 12G6384 12G6385 12G6386 Units 1 11 1 1 1 1 1 1 1 1
  • Lexmark 13P0150 | Service Guide - Page 216
    500W Fuser Lamp, 115V 500W Hot Roll Fuser Lamp, 220V 500W Hot Roll Fuser Lamp, 115V 400W Backup Roll Fuser Lamp, 220V 400W Backup Roll 7-6 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 217
    Assembly 2.1: Fuser 5060-XXX AsmIndex 2.1-1 2 NS NS Part Number 12G6414 12G6543 12G6545 Units 1 4 1 1 Description Fuser Drive Assembly Screws PP 12G6309 WEB Oiler Index Drive Assembly WEB Oiler Assembly Parts Catalog 7-7
  • Lexmark 13P0150 | Service Guide - Page 218
    5060-XXX Assembly 3: Vacuum Belt Transport Assembly AsmIndex 3-1 2 3 Part Number 12G6489 12G6488 12G6428 Units 1 1 1 Description Vacuum Belt Transport Assembly Transfer Plate Assembly Second Transfer Roll 7-8 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 219
    5060-XXX AsmIndex 4-1 2 3 4 NS NS Part Number Units 12G6322 4 12 12 12G6523 4 12G6535 4 12G6536 4 Description Printhead Assembly Screw, PP 12G6534 Screw, PP 12G6539 PSD Assembly Guide Assembly, Cartridge Left Side Guide Assembly, Cartridge Right Side Parts Catalog 7-9
  • Lexmark 13P0150 | Service Guide - Page 220
    5060-XXX Assembly 5: Paper Feed Output (Redrive) 7-10 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 221
    5060-XXX Assembly 5.0: Paper Feed Output (Redrive) AsmIndex 5-1 2 3 4 5 6 7 8 9 Part number 56P0107 12G6493 12G6492 12G6355 12G6513 12G6512 12G6356 Units Description 1 Anchor, Bracket Mounting 2 Upper Door Hinge 2 Screw, PP 12G6533 1 Redrive Assembly, Inner 1 Right Upper Door Assembly
  • Lexmark 13P0150 | Service Guide - Page 222
    5060-XXX Assembly 6: Multipurpose Feeder (MPF) 7-12 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 223
    Screw, PP 12G6533 Frame Bias Latch Frame Bias Latch Cover Screw, PP 12G6533 Frame Bias Spring MPD Support Bracket Cover Sensor Mount Bracket Paper Out/Low Sensor MPF Support Bracket Spring MPF Support Bracket MPF Bracket Assembly MPF Drive Gear MPF Drive Gear Bushing MPF Drive Gear Shaft MPF
  • Lexmark 13P0150 | Service Guide - Page 224
    5060-XXX Assembly 7: 500-Sheet Integrated Tray 7-14 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 225
    5060-XXX Assembly 7.0: 500-Sheet Integrated Tray AsmIndex 7-1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part number 12G6416 12G6419 12G6418 12G6424 12G6423 12G6422 12G6538 12G6425 12G6426 12G6568 12G6421 12G6420 12G6417 99A0120 Units 1 1 1 1 1 1 10 1 1 1 1 1 1 1 2 Description 500-Sheet Tray Assembly
  • Lexmark 13P0150 | Service Guide - Page 226
    Arm Transparency Lift Link Paper Level Sensing Assembly Sensor, Paper Out/Low Flag, Paper Out/Low Cable, Paper Media Low/Out Tray Interlock Bracket 7-16 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 227
    12G6437 12G6443 12G6444 12G6445 12G6413 Units 1 1 1 3 3 1 3 2 3 1 1 Description ITU Assembly ITU Drive Assembly Screw, PP 12G6309 Rear V-Block Guide Front V-Block Guide Bellcrank, ITU Black Transfer Front Bellcrank, ITU Transfer Front ITU Bias Spring Bellcrank, Transfer Rear Bellcrank, Black
  • Lexmark 13P0150 | Service Guide - Page 228
    5060-XXX Assembly 10: Cartridge Contact Assembly 7-18 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 229
    Units Description 8 Developer Pin Spring 1 Plug Spring 1 Toner Level Spring 1 Spring Toner Plug 6 Contact Pin 1 Housing, Cartridge Contacts 1 Cartridge Support Roller 1 TAR Contact 1 Developer Roll Contact 1 Doctor Blade Contact 1 Charge Roll Contact 1 PC Drum Contact 1 Cap
  • Lexmark 13P0150 | Service Guide - Page 230
    Assembly 11: Electronics 5060-XXX 7-20 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 231
    5060-XXX Assembly 11.0: Electronics AsmIndex 11-1 1 1 1 1 1 1 1 1 1 1 2 2 3 4 Part number 11A9095 43H5544 1339517 1339519 1339520 1339521 1339522 1339523 1339524 1339525 1339544 12G6329 12G6330 Units Description 1 Power Cord Set U.S., Canada (LV), Brazil (LV), Colombia (LV), Costa Rica (LV),
  • Lexmark 13P0150 | Service Guide - Page 232
    Assembly 11.1: Electronics 5060-XXX 7-22 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 233
    RIP Card Ground Shield RIP Card Assembly - Network INA Riser Support Bracket Riser Card Assembly w/o Support Brackets Standoff, INA RIP Spacer SDRAM DIMM 128MB, Model 5060 Panel Cable, Fuser and Y Cartridge Motor Cable, C and M Cartridge Motor Cable, ITU and K Cartridge Motor Cable, Smart Chip Cable
  • Lexmark 13P0150 | Service Guide - Page 234
    High Voltage Power Supply - Developer Contact Assembly, Black Terminal Contact Assembly, Magenta Terminal Contact Assembly, Cyan Terminal Contact Assembly, Yellow Terminal Terminal, Contact Spring 7-24 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 235
    5060-XXX Assembly 11.3: Electronics Asm- Part Index Number 11.3-1 12G6336 2 3 12G6323 4 12G6387 5 Units 1 12 1 1 14 Description Engine Card Shield Assembly Screw, PP 12G6531 Engine Card Assembly Ground Strap Screw, PP 12G6309 Parts Catalog 7-25
  • Lexmark 13P0150 | Service Guide - Page 236
    Assembly 11.4: Electronics 5060-XXX AsmIndex 11.4-1 2 3 4 5 6 NS Part Number 12G6343 12G6361 12G6479 12G6382 12G6529 12G6490 Units 1 1 2 1 1 2 1 Description RIP Fan Duct RIP Fan Assembly Screws, PP 12G6530 VTB Fan Fuser Fan Screws, Fuser Fan Mounting VTB Fan Gap Cover 7-26 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 237
    5060-XXX Assembly 11.5: Electronics Asm- Part Index Number 11.5-1 12G6494 2 12G6470 3 12G6469 4 12G6467 5 12G6468 6 7 12G6466 NS 12G6472 NS 12G6505 Units 1 1 1 4 1 1 4 1 1 Description Waste Toner Container Waste Container Latch Spring Waste Container Latch Size Sensing Spring Size
  • Lexmark 13P0150 | Service Guide - Page 238
    Assembly 11.6: Electronics 5060-XXX Asm- Part Index Number 11.6-1 2 12G6526 3 12G6527 Units 4 3 1 Description Screw, PP 12G6530 Cartridge Drive Motor Assembly, Cyan/Magenta/Black Cartridge Drive Motor Assembly, Yellow 7-28 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 239
    5060-XXX Assembly 11.7: Electronics Asm- Part Index Number 11.7-1 12G6446 2 NS 12G6438 NS 56P0171 NS 56P0172 NS 56P0173 Units 1 3 1 1 1 1 Description BOR Drive Assembly Screw, PP 12G6309 BOR Spring, Yellow BOR Spring, Magenta BOR Spring, Cyan BOR Spring, Black Parts Catalog 7-29
  • Lexmark 13P0150 | Service Guide - Page 240
    5060-XXX Assembly 12: Output Expander 7-30 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 241
    , Output Tray 1 Latch, Output Tray 2 Shaft Bearing PP 99A0572 2 Bracket, Attach 2 Spring, Swing Arm 1 Output Expander Assembly, Mechanical Linkage 1 Cover, Rear Support 1 Rear Cover 1 Level Sensor Bracket 1 Flag, Output Paper Level 1 Sensor, Dual Bin Full Parts Catalog 7-31
  • Lexmark 13P0150 | Service Guide - Page 242
    5060-XXX Assembly 12.1: Output Expander 7-32 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 243
    5060-XXX Assembly 12.1: Output Expander AsmIndex 12.1-1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 NS Part number 56P0405 99A0368 99A0363 56P0410 56P0400 99A0361 99A0362 99A0364 99A0482 99A0481 99A0912 99A0351 99A0913 99A1744 Units Description 1 Door Assembly, Right Jam Access 1 Shaft Assembly, Lower
  • Lexmark 13P0150 | Service Guide - Page 244
    Assembly 13: 5-Bin Mailbox 5060-XXX 7-34 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 245
    Mailbox Pass thru 5 Tray, Paper Cap 1 Bracket Asm, Bail Attach 1 Kit, 5-Bin Mailbox Asm 1 Bail, order 99A1743, 5-Bin Mailbox Asm Kit 5 Support, Paper Tray 5 Stop Asm, Paper Tray 4 Flag, Bin Full 1 Rear Structural Cover 5 Cable, Dual Sensor 5 Sensor, Dual Paper Height 1 Cable
  • Lexmark 13P0150 | Service Guide - Page 246
    5060-XXX Assembly 13.1: 5-Bin Mailbox 7-36 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 247
    5060-XXX Assembly 13.1: 5-Bin Mailbox AsmIndex 13.1-1 2 3 4 5 6 7 8 9 10 11 12 13 14 NS NS NS NS NS NS Part number 99A1741 99A1727 99A1728 99A1731 99A1729 99A1730 99A1789 56P0418 99A1732 99A1738 99A1722 99A1787 99A1721 99A1734 99A0462 99A1715 99A1717 99A1788 99A0450 Units Description 4 Spring,
  • Lexmark 13P0150 | Service Guide - Page 248
    5060-XXX Assembly 14: 500-Sheet Tray Option 7-38 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 249
    1 Paper Size Sensing Assembly 1 Bellcrank Lift Spring 1 500 Base Assembly 7 Machine Pad 1 Plate, 500 Support Assembly 1 Paper Guide 1 Wall Support plate 1 Base Door Assembly 1 Spring 1 500 Option Deflector 1 Grounding Spring 1 Transparency Sensor Arm 1 Transparency
  • Lexmark 13P0150 | Service Guide - Page 250
    5060-XXX Assembly 14.1: 500-Sheet Tray Option 7-40 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 251
    5060-XXX Assembly 14.1: 500 Sheet Tray Option AsmIndex 14.1-1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part number 12G6416 12G6419 12G6418 12G6424 12G6423 12G6422 12G6538 12G6425 12G6426 12G6568 12G6421 12G6420 12G6417 99A0120 Units 1 1 1 1 1 1 10 1 1 1 1 1 1 1 2 Description 500-Sheet Tray Assembly
  • Lexmark 13P0150 | Service Guide - Page 252
    Support 1 Sensor Mount Plate 1 Duplex Support Plate 1 Duplex Support Bracket 1 Chassis Ground Spring 1 Back Support 2 Idler Flange 1 Belt Tensioner Spring Retainer Parts Packet 99A0267 5 Redrive Bearing 1 Deflector Follower Assembly 2 Paper Guide Assembly 7-42 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 253
    Assembly 1 Aligner Arm Spring 1 Bellcrank Assembly 1 Pass Thru Shaft Assembly 1 Brake Pad 1 Decurl BAC Assembly 1 Brake Spring 1 5mm Bushing 1 Reduction Gear Shaft 2 Aligner Spring 2 Paper Guide Assembly Parts Catalog 7-43
  • Lexmark 13P0150 | Service Guide - Page 254
    1 AC Outlet 1 Feed Unit 1 Front Cover 1 Cover, Main CA 1 Cover, CA Sub 1 Right Cover 1 Left Cover 1 Rear Cover 1 Separator Roll Assembly 1 Cam Separator Assembly 7-44 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 255
    ) Hard Disk, 5GB or larger ISP Hard Disk (unformatted) Forms Software Forms Director Software Lexmark Forms 4MB DIMM Lexmark Forms 8MB DIMM Lexmark Forms 16MBMB DIMM Lexmark Forms 32MB DIMM Lexmark Forms 64MB DIMM Hard Drive Mounting Kit MarkNet Token Ring Print Server MarkNet N2001e Ethernet 10
  • Lexmark 13P0150 | Service Guide - Page 256
    /423, PP 12G6533 1 Screw Type 484, PP 12G6534 1 Screw, 500-Sheet Tray, PP 12G6538 1 Screw Type 124, PP 12G6539 1 Screw Type 121, PP 12G6540 7-46 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 257
    Diverter Test 3-13 Print Registration 3-18 Diagnostic Mode 3-1 Diagnostics Error Code Table 2-3 Service Checks 2-43 Sub Error Code Table 2-15 Symptom Table 2-1 System Board LED Error P Parallel Wrap Test 3-6 Parts Catalog Autocompensator Assembly 7-16 Cartridge Contact Assembly 7-18 Covers 7-2 I-1
  • Lexmark 13P0150 | Service Guide - Page 258
    Inspection Guide 6-1 Scheduled Maintenance 6-2 Screw Identification Table 4-4 SDRAM Memory Test 3-5 Serial Wrap Test 3-7 Service Checks 2-43 AC & DC Power 2-50 Autocompensator 2-91 Cartridge Drive 12G6309 7-46 12G6310 7-23 12G6311 7-23 12G6312 7-23 12G6313 7-23 12G6314 7-23 I-2 Service Manual
  • Lexmark 13P0150 | Service Guide - Page 259
    12G6315 7-23 12G6316 7-23 12G6317 7-23 12G6318 7-23 12G6319 7-3, 7-23 12G6320 7-23 12G6321 7-23 12G6322 7-9 12G6323 7-25 12G6324 7-23 12G6325 7-23 12G6326 7-23 12G6327 7-24 12G6328 7-24 12G6329 7-21 12G6330 7-21 12G6331 7-23 12G6332 7-23 12G6333 7-23 12G6334 7-23 12G6335 7-23 12G6336 7-25 12G6337
  • Lexmark 13P0150 | Service Guide - Page 260
    7-11 12G6493 7-11 12G6494 7-27 12G6503 7-23 12G6504 7-23 12G6505 7-27 12G6506 7-3 12G6507 7-3 12G6509 7-23, 7-45 12G6510 7-5, 7-39 I-4 Service Manual 5060-XXX 12G6511 7-5 12G6512 7-11 12G6513 7-11 12G6514 7-6 12G6515 7-6 12G6518 7-17 12G6523 7-9 12G6529 7-26 12G6530 7-46 12G6531 7-46 12G6532 7-46
  • Lexmark 13P0150 | Service Guide - Page 261
    56P0170 7-3 56P0171 7-29 56P0172 7-29 56P0173 7-29 56P0400 7-33 56P0401 7-31 56P0402 7-31 56P0405 7-33 56P0407 7-31 56P0408 7-31 56P0409 7-31 56P0410 7-33 56P0411 7-35 56P0412 7-35 56P0413 7-35 56P0416 7-35 56P0417 7-35 56P0418 7-37 56P0420 7-35 56P0422 7-35 56P0423 7-35 56P0430 7-42 56P0431 7-42
  • Lexmark 13P0150 | Service Guide - Page 262
    7-35 99A1719 7-35 99A1721 7-37 99A1722 7-37 99A1723 7-35 99A1724 7-35 99A1725 7-35 99A1726 7-35 99A1727 7-37 99A1728 7-37 99A1729 7-37 I-6 Service Manual 5060-XXX 99A1730 7-37 99A1731 7-37 99A1732 7-37 99A1734 7-37 99A1735 7-35 99A1736 7-35 99A1737 7-35 99A1738 7-37 99A1740 7-35 99A1741 7-37
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
Lexmark
TM
C750
5060-XXX
• Table of Contents
• Start Diagnostics
• Safety and Notices
• Trademarks
• Index
• Manuals Menu
Lexmark and Lexmark with diamond design are
trademarks of Lexmark International, Inc., registered
in the United States and/or other countries.