Lexmark 6500e PRESCRIBE Emulation Technical Reference Guide

Lexmark 6500e Manual

Get Lexmark 6500e PDF manuals and user guides View all Lexmark 6500e manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark 6500e manual content summary:

  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 1
    Reference May 2011 www.lexmark.com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners. © 2011 Lexmark International, Inc. All rights
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 2
    Contents Introduction 3 Supported devices...3 Installing the PRESCRIBE emulation option 3 Flash memory and hard disk support...3 Memorex printer compatibility mode...4 Overview of limitations...4 Certification test process...5 PRESCRIBE commands 6 Command support for P41F...6 Command explanations
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 3
    can be restored. For more information on installing and uninstalling the PRESCRIBE emulation option, see the installation instructions that came with the option, or the printer User's Guide. After installing the option, set up the PRESCRIBE FRPO (Firmware RePrOgram) defaults to match the Kyocera
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 4
    compatibility mode The PRESCRIBE emulation option includes a custom extension to support an alternate font number table which is compatible with Memorex system printers. The font number mapping is as follows: Memorex font number 1 2 3 Standard PRESCRIBE font number 1 6 10 4 15 5 2 6 17
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 5
    files, fonts, or macros that are used in the print job • A soft copy of the actual print job • The model numbers of the Kyocera printers in use • A description of the problem and a hard copy output from a Kyocera printer Note: Customers must recertify new versions of the PRESCRIBE emulation option
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 6
    DPAT2 select Dash PATtern 1 Partial support or extended support (see next section for details) 2 PRESCRIBE II option 3 Not applicable (for example, unsupported paper option or diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language Supported Yes Yes Yes Yes Yes Yes
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 7
    ENDD3 END Dump ENDM END Macro ENDR END Raster data EXIT EXIT from PRESCRIBE mode FILL2 FILL closed path FLAT2 set FLATness FLST2 print Font LiST FONT change current FONT FPAT generate Fill PATtern FRPO1 Firmware RePrOgram FRPO INIT FRPO INITialize FSET2 change current Font
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 8
    TeXT RVCD2 ReceiVe Compressed raster Data RVRD ReceiVe Raster Data SBM Set Bottom Margin SCAP2 support or extended support (see next section for details) 2 PRESCRIBE II option 3 Not applicable (for example, unsupported paper option or diagnostic command) 4 Custom command extension, not part
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 9
    TEXT print TEXT UNIT set UNIT of measure XPAT generate eXpanded fill PATtern WRED2, 3 WRite EnD (O&1, 4 enter Memorex Printer Compatibility Mode 1 Partial support or extended support (see next section for details) 2 PRESCRIBE II option 3 Not applicable (for example, unsupported paper
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 10
    4.8 Command explanations BARC: draw BAR Code The extent of PRESCRIBE bar code support in version 41F is summarized in the following table. The number specified is 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Supported Yes No No No No No No No Yes No No Yes Yes No No No No No No Yes Yes
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 11
    31 32 33 34 35 36 37 38 39 40 41 42 43 44 49 Supported No No No No Yes Yes Yes No No No No No No No Yes No Yes Yes No No Yes CASS: CASSette The CASS command has been extended to support the optional paper sources. The CASS command is mapped as follows: CASS 0; CASS 1; CASS 2; CASS 3; CASS
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 12
    FRPO: Firmware RePrOgram Kyocera printers support a large set of permanent defaults which can be set using the FRPO command. The PRESCRIBE emulation option supports a subset of the more significant settings. The FRPO INIT command is supported and only affects the settings in the following table,
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 13
    Font selection Font 1 for PCL emulation. Font 8 for Proprinter and Line Printer emulations. Sets the default font to the specified font number. Sets the L5-L8 FRPO parameters are always interpreted with respect to a letter-size sheet of paper, with default top- and left-edge limits (0.20"). For
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 14
    Default emulation The factory default printer emulation is PCL. This PRESCRIBE emulation option supports a level of PCL 5e that is compatible with the HP LaserJet family of laser printers. Although the PRESCRIBE emulation option supports only one base emulation, support for IBM Proprinter (P1=1) and
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 15
    margin limit settings are always acknowledged when the base emulation is Proprinter or Line Printer. U0-U1: Line spacing This sets the number of lines printed per inch. U0 and U1 represent the integer part and the fraction part of the line spacing value, respectively. If U0 is set to 5 and U1 is
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 16
    resident. Currently, there are bitmap versions for font 9 and font 28. Setting LC to 1 forces the printer to print font 9 and font 28 using the bitmap version. The default setting of 0 forces font 9 FRPO LE parameter 0 1 2 3 Paper source No source Tray 1 Manual Manual env PRESCRIBE commands 16
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 17
    LF, 300; FRPO LG, -150; EXIT; GENF: GENerate Font The fonts generated by the PRESCRIBE emulation option with this command may differ in size and style from scalable font instead. SEM: Set Emulation Mode Kyocera printers support a list of printer emulation modes in addition to PRESCRIBE as shown:
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 18
    of a print job can be a mixture of the selected emulation data stream and PRESCRIBE. Notes: • The PRESCRIBE emulation option only supports PCL 5e, although the PRESCRIBE print environment may be initialized for Proprinter or Line Printer by using the SEM or FRPO commands. For more information, see
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 19
    7.2 16.6 PrestigeEliteBM7.2-Italic Courier Italic (scalable) 47 - 7.2 16.6 Notes: • Some of the bitmap fonts are resident in the PRESCRIBE emulation option and are not necessarily substituted with a scalable font. For more information, see "C3: Default font" on page 13. • Resident scalable
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 20
    .4 LinePrinterBM7-BoldItalic Courier Bold Italic (scalable) 66 - 7 21.4 Notes: • Some of the bitmap fonts are resident in the PRESCRIBE emulation option and are not necessarily substituted with a scalable font. For more information, see "C3: Default font" on page 13. • Resident scalable font
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 21
    in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user's responsibility. For Lexmark technical support, visit support.lexmark.com. For information on supplies and downloads, visit www.lexmark.com. If you don't have access to
  • Lexmark 6500e | PRESCRIBE Emulation Technical Reference Guide - Page 22
    for P41F 6 commands BARC 10 FRPO 12 support for P41F 6 D devices supported 3 F firmware reprogram 12 flash memory and hard disk support 3 fonts bitmap font simulation 19 FRPO commands 12 I installing PRESCRIBE emulation 3 M Memorex printer compatibility mode 4 N notices 21 O overview of limitations
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
PRESCRIBE Emulation P41f
Technical Reference
May 2011
www.lexmark.com
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
All other trademarks are the property of their respective owners.
© 2011 Lexmark International, Inc.
All rights reserved.
740 West New Circle Road
Lexington, Kentucky 40550