Lexmark 782n SCS/TNe Emulation User’s Guide
Lexmark 782n - C XL Color Laser Printer Manual
 |
UPC - 734646143080
View all Lexmark 782n manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark 782n manual content summary:
- Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 1
product description, see "Specifications, Requirements, Features" on page 275. SCS data is received in a LAN environment using the Telnet extended protocol. The Card for IPDS and SCS/TNe adds support for the TN3270E and the TN5250E protocols. A correctly configured printer can receive, process - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 2
Requirements and Specifications IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Supported Products With the appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C770, C772 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 3
called STD Net). • MarkNet internal print server (Ethernet). If you need to update your Standard Network or MarkNet firmware, refer to "Support" on page 4. For further information on requirements and specifications, see the appendix starting on page 275. Getting Started: Equipment Requirements and - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 5
This page is intentionally left blank Support: Customer Support 5 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 6
Using a Browser" on page 23 ff.) • Work with the settings remotely using IDB option strings (see "IDB Basics" on page 246 ff. and "Additional TN5250e Printer Commands Using IDB" on page 258 ff). Using IDB in this way is a highly technical process used only in connection with configurations and re - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 7
on page 246 for additional information. Note that in most cases, only technical specialists need to understand and use IDBs. Setup Options vs. Printer Setup Options Setup Options Changes to the option settings under the SCS/TNe MENU will only affect the printing of SCS jobs received through a LAN - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 8
may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings. Printer Setup Options Changes to printer settings under the various printer menus, such as Paper Menu and Settings, will - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 9
Panel Introduction This chapter introduces the SCS/TNe MENU options as well as illustrating how how the control panel works. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs are illustrated here. If you are familiar with the use of the control panel, skip - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 10
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel SCS/TNe MENU. To reach the menu: Accessing the top line in the screen shows the menu or menu group name to which the displayed items belong. Understanding the Operator Panel: Printer operator panel 10 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 11
become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator panel" on page 10. 2 Use the navigation buttons or to scroll to the desired menu and press Select. 3 Use the navigation buttons to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 12
SETUP 9 TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK 9 SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel 12 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 13
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS 9 MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup 9 Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 13 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 14
the on-screen checkmark is next to the desired setting. press the Select button Country Code English (US) 9 Fin/Swe Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 15
the Back button to return to the Ready screen. You may need to press it several times until the screen appears. Understanding the Operator Panel: Printer operator panel 15 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 16
the navigation buttons and to move between the characters. To store the new string, press Select after entering all the characters. Understanding the Operator Panel: Printer operator panel 16 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 17
the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 16. Understanding the Operator Panel: Printer operator panel 17 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 18
Emulation options and settings from the operScreen ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer is on and the Ready message appears. 2 Touch the key icon (Menus) on the operator panel 3 Touch or to scroll through the main menus - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 19
When you select an option, you will either scroll through the list of values presented ("Selecting a New Value as a Setting" on page 19), enter a number ("Changing a Numerical Setting" on page 22), or enter a text string ("Changing a Text String" on page 21). Several examples of how to use the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 20
4 Now you will see a list of menus. Touch or to scroll to the desired item. In this example locate and touch SCS OPTIONS. 5 Now you will see a list of menus. Touch or to scroll to the desired item. In this example locate and touch MISC SETTINGS. 6 Now you will see a list of options.Touch - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 21
9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 22
Changing a Numerical Setting Example: If you select Menus > Option Card Menu > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > Keep Alive Time, you will see the following on screen: Keep Alive Time 45 Touch to decrease the value or to increase the value. Touch (Submit) to save the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 23
Remote Configuration Using a Browser Introduction IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. The Card for IPDS and SCS/TNe includes an http user interface. You can use a browser, such as Microsoft Internet Explorer or Netscape, - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 24
new SCS/TNe session is established. How to Use the Browser Interface To access and change SCS/TNe option settings through your browser: 1 Access the printer web page by typing the IP address of its print server as the URL. 2 Select Configuration. 3 Select SCS/TNE Settings. 4 Select the TNe Common - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 25
as desired. 11 Select the Submit button at the bottom of the page. The Submit button sends the new values to the printer. These values are saved in the printer and will become active when the next session is started. 12 The browser will then display a confirmation that settings have been submitted - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 26
16 The SCS/TNe emulation will attempt to reconnect to the host. 17 Check to be sure that all sessions have been reconnected. Click on each TNxxxx Connection Status menu item to check the status of each session. If all configured sessions have not been established within 90 seconds, you may need to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 27
print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For TN3270e Printing Task 3 -Configuring a Print Server Task - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 28
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 28 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 29
described in IBM's VTAM documentation. The Mainframe software must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. "Mainframe Software" on page 277 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 30
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE,IRETRY=YES,IDNUM=B0008, PASSLIM=7,PUTYPE=2,DISCNT=NO,VPACING=0 LCPG90 LU LOCADDR=2,MODETAB=MT3274P,USSTAB=USB3274B, DLOGMOD=T3274M2 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 31
Sample Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or terminal devices) for telnet sessions as follows: TCP VBUILD TYPE=APPL SC0TCP01APPL AUTH=NVPACE, EAS=1, PARSESS=NO, MODETAB=ISTINCLM, SESSLIM=YES - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 32
member (i.e. IMLU1 listed above) to the host print software being used. The following is an example of a TN printer definition defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 33
for Printing via a SNA Server TIP: How to define an LU-1 printer in VTAM is described in IBM's VTAM documentation. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Two sample configurations are shown below. Sample Configuration number 1 Remote Device - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 34
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE,IRETRY=YES,IDNUM=B0008, PASSLIM=7,PUTYPE=2,DISCNT=NO,VPACING=0 LCPG90 LU LOCADDR=2,MODETAB=MT3274P,USSTAB=USB3274B, DLOGMOD= - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 35
details. Refer also to IBM books such as the IBM book OS/390 eNetwork Communications Server V2R5, TCP/IP Implementation Guide, Volume 1: Configuration and Routing (document no. SG24-5227-00). The printer with the SCS/TNe Emulation is defined to the Telnet server in much the same way as a display LU - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 36
ENDPRTGROUP IPGROUP SPECIP 157.184.116.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 37
group as shown above (PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 38
Configuring an SNA Server For TN3270e Printing IMPORTANT: The TN3270e components have to be installed in order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways and routers. The procedure in this section shows how to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 39
created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 40
may cause a loss of SCS/TNe print capability. SCS/TNe Emulation printing requires a MarkNet internal print server or a Standard Network port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Touch Reports. 3 Scroll until one or more of the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 41
server settings may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus > Network/Ports. setting and corresponds to "disabled". Other settings may cause communication problems. A setting of "0" allows the host or SNA server timeout - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 42
3 Set the TCP/IP option values shown in the table below. Select Menus > Network/Ports > TCP/IP. You will need to contact your network administrator for several of the values. TCP/IP Option Value Description Address Address available from your network administrator. Netmask Netmask for your - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 43
Task 4 Configuring the SCS Settings Several SCS option values may need to be changed to properly format and print SCS jobs that do not contain formatting commands in the job. The following three settings are usually the most important, but there are many other possibilities. TIP: Refer to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 44
1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > SCS OPTIONS > MISC SETTINGS > Euro Support. MISC SETTINGS Option Default Value Euro Support (IDB Event 191) No Recommended Value Comments Your preference. Enable with Yes. 2 Scroll to Yes. Touch Submit button to save the setting - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 45
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. SCS jobs are printed - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 46
with your system administrator whether you need to specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. 0.0.0.0 The TNe number is defined for the Telnet service. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe Emulation 46 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 47
to 10 characters) This name must be defined on the host or SNA Server. Please note! Some hosts and servers only recognize uppercase LU Names. Specific Check with your system administrator for the correct setting. The device type must be defined on the host. Telnet NOP or None Set this to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 48
5 To activate the new settings, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. Wait approximately one minute. If all values are set correctly, this should allow enough time for the SCS/TNe - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 49
Task 6A Verifying the Mainframe Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 90) From the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 50
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. 3 From the main frame - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 51
Task 6B Verifying the Mainframe/SNA Server Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 90) - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 52
end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > be sure that the printer in question has been defined-and activated-as a client on the SNA server. Consult your SNA manual. Mainframe Installation Setup: Task - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 53
obtain the latest version of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring the SCS Settings Task - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 54
TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 277 lists host software which supports these protocols. To configure the host check and set the following three system values. System Value QAUTOCFG QAUTORMT Required - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 55
System Value QAUTOVRT Required Value Controls the automatic configuration of virtual devices. Must be set to an adequate number of devices Sample commands: DSPSYSVAL QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 56
Task 2 Configuring a Print Server SCS/TNe emulation printing requires a MarkNet internal print server or a Standard Network port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Touch Reports. 3 Scroll until one or more of the following - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 57
server settings may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus > Network/Ports. setting and corresponds to "disabled". Other settings may cause communication problems. A setting of "0" allows the host SNA server, or SCS - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 58
3 Set the TCP/IP option values shown in the table below. Select Menus > Network/Ports > TCP/IP. You will need to contact your network administrator for several of the values. You will need to contact your network administrator for several of the values. TCP/IP Option Address Netmask Gateway Enable - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 59
TCP/IP Option Value Description Enable RARP On or Off On, if you use a RARP server. Off, if you set the IP address another way. Enable BOOTP On or Off On, if you use a BOOTP server. Off, if you set the IP address another way. Auto IP On or Off Default is On. This is the recommended setting - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 60
SCS OPTIONS menu values is saved. All four TN5250e connections use the same set of SCS OPTIONS values. A. To select settings for your specific country 1 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > MISC SETTINGS > Country Code. Scroll to your preferred country and - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 61
2 Still within MISC SETTINGS, locate Codepage. Scroll to your preferred code page and touch Submit to save it. Option Default Value Codepage (IDB Options 240 and 241) Multi 500 Recommended Value Comments Your preferred code page 3 Still within MISC SETTINGS, locate Lines Per Page. Scroll to the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 62
Option Page Length (IDB Opt. 82 & 83) Option Page Width (IDB Opt.84 & 85) 6 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > PAPER SETTINGS > Page Length. Scroll to the desired value and touch Submit to save it. Default Value 16848 (for A4) Recommended Value Comments - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 63
1 Select Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 64
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. SCS jobs are printed - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 65
Check with your system administrator whether you need to specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. The host's IP address be defined for the Telnet service. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 66
be auto configured. Contact your system administrator if you do not know the library name. Normal Leave this option at its default value to have printer intervention required conditions reported to the host. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 66 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 67
sense the writer has ended after the first SCS job has started to print. If the writer ends before sending an SCS job to the printer, the TN5250e emulation will not be able to sense the writer has ended. 6 Set Print # Active to Yes for each connection you wish to activate - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 68
Wait approximately one minute. If all values are set correctly, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 90. AS/400 and iSeries - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 69
Task 5 Verifying the Host Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN5250E Connection Status (see page 160). From the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 70
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. Through the http (browser) - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 71
SCS/TNe Cancel About Cancel Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 72
Job 1 Press the Select button on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, continue printing without canceling the job, press the Back button. Important Configuration Basics: Printer Cancel Job 72 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 73 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 74
MFP Cancel Job 1 While any job is printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 75
Operations Reference - Common Setup Introduction As indicated in the tree diagram below, the SCS/TNe MENU is divided into three branches. This section describes the COMMON SETUP menu structure and options for the SCS/TNe Emulation From a Ready status, touch Menus. Locate and touch the Option Card - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 76
How to access the Menu Settings Page • Reset ALL Def You will always be able to see the selected value for each option on the Menu Settings page. • From the Operator Panel: Select Menus > Reports > Menu Settings Page. • Through the http (browser) user interface: Connect to the print server by - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 77
Menu Options Overview . Option name Values Disconnect Ses Do Not Disconn., Disconnect Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 78
and On or when a Reset TN Ses. is performed. See the Reset TN Session option below. A Disconnect Ses. should be performed before powering Off the printer. Operator panel text Comments Do Not Disconn. Do not disconnect any sessions. This performs the same action as if Back had been pressed in the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 79
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. This option disconnects ALL - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 80
program attached to the selected port to receive the trace data, the printer will remain Ready and may not complete establishing a session with the host performance, it should only be enabled when needed by service personnel for troubleshooting and service. NOTE: If the SCS/TNe Emulation is set - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 81
trace data output. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be added to provide additional ports for output of the debug trace data. Operations - Common Setup: SCS Debug - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 82
panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common Setup: Reset ALL Def 82 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 83
Operations Reference - TN3270E SETUP Introduction This section describes the SCS/TNe Emulation TN3270E SETUP menu structure and options. Settings under this menu are used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 84
Device Type Keep Alive Type Keep Alive Time MISC SETTINGS FF Support Non-Print Char CSC Characters IDB Delimiter Use IR Format Ctrl Line Spacing LPP Transparency Form Strings IBM Trn Code Leadin Sequence Euro Support PAPER SETTINGS Left Margin Right Margin Top Margin Bottom Margin Source Input - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 85
The SCS/TNe Emulation has default settings for most SCS commands found in an SCS job. If one or more SCS settings are missing from a job, the SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu for the option. Settings specified in an SCS job override the SCS/TNe Emulation default - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 246 ff.) Operations - TN3270E SETUP: Introduction 86 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 87
NETWORK SETUP Menu: Options Overview The NETWORK SETUP menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the NETWORK SETUP menu. NETWORK SETUP Option name Print Active TN3270 Defaults Connect Status SERVER INFO Values No *, Yes Do Not - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 88
Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 89
TN3270 Defaults This Network Setup option restores the TN3270e NETWORK SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 90
option displays the connection status with the host. The option cannot be changed by the user. Normally only the primary status is shown. If problems occur, a last response message is appended to the primary status message. The complete status message text may not be displayed. Refer to the tables - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 91
No support for that device-type Lst Rsp:Name unknown to server Lst Rsp:The requested device is in use Lst Rsp:Terminal/Printer name Server to establish a TCP/IP connection. Comments The Telnet server does NOT support the device type requested by the SCS/TNe Emulation. Select another device type with - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 92
is not a terminal. Lst Rsp:The device is a partner to some terminal The SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 93
up to 16 characters TN Server Port 23 *, range: 0 - 65000 LU Name [undefined] *, ASCII name with up to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 *, range: 1 - 32000 [seconds] A description of each SERVER INFO - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact the host or Telnet server. Option Value Use IP Address * Use Hostname Comments Use the IP address specified with the IP Address option. Use the hostname specified with the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 97
TN Server Port This Network Setup > Server Info option specifies the TCP Telnet server port defined on the host. Check with your system administrator for the correct Telnet server port to use. Option Value 23 * [0..65000] Comments This is the default port number for Telnet sessions according to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 98
name assigned to the SCS/TNe Emulation on the host or SNA gateway. Remember also to check the setting of the Device Type option. If a specific LU name is requested, then the name must be defined and available on the host. After a connection is active, the LU name can be viewed - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 99
* Associated Generic Comments Request a specific LU name. Make sure this has been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 100
Keep Alive Type IMPORTANT: If the Mainframe has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type of keep alive signal sent to the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive signal sent to the host or SNA gateway server. The Keep Alive Type setting specifies the type of signal sent to the host. Set this option to a value smaller than the session's - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 102
IDB Option 122) MISC SETTINGS PAPER SETTINGS Values Yes *, No Sub-menu. See SCS Options > MISC SETTINGS Menu: Options Overview (page 104) and FF Support (IDB Option 5) (page 106). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 131) and Left Margin (IDB Option 103) (page 133 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 103
COR/APO Sett (IDB Option 122) This SCS Options option controls whether or not Automatic Print Orientation (APO) is used. APO automatically controls page orientation. When APO is enabled the SCS/TNe Emulation calculates the print area required for printing the document. This is based on page - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 104
menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters (IDB Options 8 & 9) IDB Delimiter (IDB Option 7) Use IR (IDB Option 21) Format Ctrl Sup - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 105
(IDB Option 167) Form Strings (IDB Option 168) IBM Trn Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range: 1 - 255 6 *, range: 1 - 255 Single *, Double 64 *, range: 1 - 255 Intermate *, Axis, Enable MPI feat ASCII - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 106
FF Support (IDB Option 5) This SCS Options > MISC Settings option defines if a form feed and/or a line feed is generated when & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 106 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 107
Non-Print Char (IDB Option 3) This SCS Options > MISC Settings option defines the replacement character to substitute for an unprintable character found in the data stream. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of printable characters and their values. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 108
of the Leadin characters defined with option 171 and 172. Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are ASCII characters in the decimal range 33 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 for - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 109
IDB Delimiter (IDB Option 7) This SCS Options > MISC Settings option defines the delimiter used in the Advanced IDB command language to separate programming commands. The IDB option value is an ASCII character in the decimal range 32 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 110
) This SCS Options > MISC Settings option controls Intervention Required (IR) reporting to the host. If the option is enabled, IR signals are sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 111
Format Ctrl Sup This SCS Options > MISC Settings option defines the suppression (IDB Option 177) of control codes after Power On. Option Value Normal * No AutoNL No AutoNL' No Codes IDB Value 0 1 2 3 Comments Standard handling of control codes after Power On. It can be disabled with the +M - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 112
default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 112 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 113
generated CR, LF, NL and FF control codes are suppressed and the auto-NL function is disabled. Control codes can only be sent to the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: After this command, all Host generated control - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 114
Country Code (IDB Option 2) This SCS Options > MISC Settings option defines the character set. Option Value Aus/Ger Aus/Ger (alt) Belgian Brazilian Can Bilin Can French Dan/Nor Dan/Nor (alt) English (UK) English (US) * Fin/Swe Fin/Swe (alt) Fre/Azerty International Italian IDB Value 2 3 4 5 6 7 8 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 115
Option Value IDB Value Portugal 16 Portugal (alt) 17 Spanish 18 Spanish Speak. 19 Spanish (alt) 20 Ger/Fre (Swiss) 21 Jap/Eng 22 Spa/Text proc. 23 Comments Portuguese Portuguese Alternate Spanish Spanish speaking Spanish Alternate Swiss German/Swiss French Japanese/English Spanish data/ - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 116
Skip Blank Page (IDB Option 32) This SCS Options > MISC Settings option controls whether or not blank pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &% - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 117
CPI (IDB Option This SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 118
Max Prt Pos (IDB This SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 119 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 120 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 121
LPP (IDB Option 107) This SCS Options > MISC Settings option defines the number of lines per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 122
Transparency This SCS Options > MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 123
Form Strings (IDB Option 168) IMPORTANT: Avoid using a character between 0 - 9 (ASCII 49 - 57), A - F (ASCII 65 - 70). Also, avoid using one of the characters used as lead in for one of the other CSC commands. This SCS Options > MISC Settings option defines the lead in character for the Formatted - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 124
IBM Trn Code (IDB Option 169 bit 1) This SCS Options > MISC Settings option defines how transparent data is translated. Option Value Normal * No Translation IDB bit option value Comments 0 Transparent data is translated from EBCDIC to ASCII. Data outside the range 40H - FEH is printed as a - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 125
Leadin Sequence (IDB Option 169 bit2) This SCS Options > MISC Settings option defines the kind of lead in sequence used. Option Value Normal * Without '&%' IDB bit option value Comments 0 Normal user defined trans- parent handling. 1 User defined transparent lead in characters are used - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 126
This SCS Options > MISC Settings option controls Euro character (IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 127
SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview The BOLD PRINT menu is a sub-menu under the MISC SETTINGS menu. The following table lists menu options found under the BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS ( - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 128
Bold On CR (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 129
Bold On BS (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 130
Bold On Multi BS (IDB Opt. 22 bit 3) This SCS Options > MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 131
SCS Options > PAPER SETTINGS Menu: Options Overview The PAPER SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. Option name Left Margin (IDB Option 103) Right Margin (IDB Option 104) Top Margin (IDB Option 108) - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 132 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 133
Left Margin (IDB Option 103) This SCS Options > Paper Settings option defines the left margin position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 134
Right Margin (IDB Option 104) This SCS Options > Paper Settings option defines the right margin position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &% - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 135
Top Margin (IDB Option 108) This SCS Options > Paper Settings option defines line number position of the top margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 136
Bottom Margin (IDB Option 109) This SCS Options > Paper Settings option defines the line number position of the bottom margin. The line height depends on the setting of the LPI (IDB Option 105) option. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 137
IDB Option 113) source. Option Value Prtr Setting Tray 1 * Tray 2 Tray 3 Tray 4 Tray 5 IDB Value 0 1 2 3 4 5 Comments Feed paper from the paper source selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 138
Tray 1 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 139
Tray 2 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 140
Tray 3 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 141
Tray 4 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 142
Tray 5 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 143
Tray1 Paper Size (IDB Option 90) This SCS Options > Paper Settings option specifies the paper size to be used when Source Input (IDB Option 113) Tray 1 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 144
Tray2 Paper Size (IDB Option 91) This SCS Options > Paper Settings option specifies the paper size to be used when Source Input (IDB Option 113) Tray 2 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 145
Tray3 Paper Size (IDB Option 92) This SCS Options > Paper Settings option specifies the paper size to be used when Source Input (IDB Option 113) Tray 3 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 146
Tray4 Paper Size (IDB Option 93) This SCS Options > Paper Settings option specifies the paper size to be used when Source Input (IDB Option 113) Tray 4 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 147
Tray5 Paper Size (IDB Option 94) This SCS Options > Paper Settings option specifies the paper size to be used when Source Input (IDB Option 113) Tray 5 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 148
TEST OPTIONS Menu: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 149
SCS3270 Hex Dump This Test option enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 150
Print 3270 IDB This Test option prints a tabular report of the current IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 151
SCS3270 Defaults This Test option restores the TN3270e SCS OPTIONS setting to their factory default settings. Other printer emulation defaults are unchanged. The restored settings become active on the next SCS job. Option Value Do Not Restore * US-Default Non-US-Default Comments - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 152
Tray2 Paper Size (IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 153
Operations Reference - TN5250E SETUP Introduction This section describes the SCS/TNe Emulation TN5250E SETUP menu structure and options. Settings under this menu are used when printing from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 154
Print 4 Active TN5250#4 Default Connect 4 Status Overlay Call Prop Font Move Compress CPI Move Hor/Ver Format Ctrl Sup Download Font Euro Support SCS5250 Hex Dump Print 5250 IDB SCS5250 Defaults SERVER 1 INFO SERVER 2 INFO SERVER 3 INFO SERVER 4 INFO Name/IPaddress 1 IP 1 Address Hostname - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 155
The SCS/TNe Emulation has default settings for most SCS commands found in an SCS job. If one or more SCS settings are missing from a job, the SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu for the option. Settings specified in an SCS job override the SCS/TNe Emulation default - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 156
the menu option to the factory default or how to perform the described action (cf. "IDB Basics" on page 246 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 258 ff.) Operations - TN5250E SETUP: Introduction 156 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 157
CONNECTION # Menu: Options Overview The SCS/TNe Emulation supports four concurrent TN5250E sessions. Each session has its own unique set of network settings. These are located in the CONNECTION#1 - CONNECTION#4 menus. The SCS OPTIONS ( - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 158
the activation of the SCS/TNe Emulation for TN5250E communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 159
TN5250## This Connection# option restores the TN5250E CONNECTION #1, Default #2, #3, or #4 factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 160
Connect # Status This Connection# option displays the connection status with the host. The option cannot be changed by the user. The first part of the line shows the primary status message of the connection followed by a last response message received from the host. The complete status message text - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 161
Connect # Status: Primary status messages Comments Session Disconnected and Halted All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 162
Connect # Status: Last response messages Lst Rsp:8902:Device not available Lst Rsp:8903:Device not valid for session Lst Rsp:8906:Session initiation failed Lst Rsp:8907:Session failure Lst Rsp:8910:Controller not valid Lst Rsp:8916:No matching device found Lst Rsp:8917:Not authorized to object Lst - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 163
Connect # Status: Last response messages Lst Rsp:8935:Session rejected Lst Rsp:8936:Security failure on session Lst Rsp:8937:Automatic sign-on rejected Lst Rsp:8940:Automatic config. failed Lst Rsp:I904:Source at incompatible release Comments Check with system operator. Check with system operator. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 164
Connection# > SERVER # INFO Option name Values Keep Alive Time 45 *, range: 1 - 32000 [seconds] MSGQ # Name QSYSOPR *, ASCII name with up to 10 characters. MSGQ # Lib *LIBL *, ASCII name with up to 10 characters. IR # Reply Normal *, Offline, No Reply Auto Sense # END No *, Yes A - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 165
IP # Address This Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 166
Hostname # This Connection# > Server# Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 167
Server # TN Port This Connection# > Server# Info option specifies the TCP Telnet server port defined on the host. Check with your system administrator for the correct Telnet server port to use. Option Value 23 * [0..65000] Comments This is the default port number for Telnet sessions according to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 168
Device # Name This Connection# > Server# Info option specifies the device and writer name associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 169
Keep Alive Type IMPORTANT: If the host has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Connection# > Server# Info option specifies the type of keep alive signal sent to the host. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 170
Keep Alive Time TIP: Set this option to as big a value as possible. Be sure it is smaller than the session's inactivity timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires between each keep - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 171
MSGQ # Name This Connection# > Server# Info option specifies the message queue name on the host to which Intervention Required conditions are reported. The message queue name must already exist on the host. It will not be auto created. The MSGQ # Lib option may be used to set the message queue - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 172
MSGQ # Lib This Connection# > Server# Info option specifies the message queue library for the message queue specified in the MSGQ # Name option. The message queue library must already exist on the host. It will not be auto created. Leave this option at the default if you do not know the library - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 173
IR # Reply This Connection# > Server# Info option controls the reporting of Intervention Required Replies to the host. Option Value Normal * Offline No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 174
Auto Sense # END This Connection# > Server# Info option controls whether or not the SCS/TNe Emulation senses automatically if the host has ended the Writer. This may be necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 175
) Use Escape *, Use Line feed, Space + Escape, Linefeed + Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 175 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 176
SCS OPTIONS Option name CSC CHARACTERS COR/APO SETTINGS MISC SETTINGS PAPER SETTINGS Values Sub-menu. See SCS OPTIONS > CSC CHARACTERS Menu: Options Overview (page 190) and SCS OPTIONS > CSC CHARACTERS Menu: Options Overview (page190). Sub-menu. See SCS OPTIONS > COR/APO SETTINGS Menu: Options - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 177
Overlay Call (IDB Option 28) This SCS Options option defines if an overlay call (predefined string) is printed on the top of each page. The overlay may contain a call to an electronic form, a macro, or the string stated by the OVLDRW command itself. It has a maximum of 255 characters. A string for - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 178 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 179
) This SCS Options option controls whether or not the SCS/TNe Emulation uses proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which the host expects the characters to have. The SCS/TNe Emulation adjusts each character - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 180 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 181
This SCS Options option defines the compression of the horizontal character spacing. The command is used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 10 CPI, 96 characters on a line using 12 CPI and 120 characters on - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 182 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 183
Move Hor/Ver (IDB Option 158) This SCS Options option determines how horizontal and vertical moves are performed. Refer to the IDB options 211 - 213 if escape sequences (ESC) are used for horizontal movement and to option 238 if spaces (SP) are used. Option Value Use Line feed Use Escape * Space + - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 184 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 185
"Auto newline" feature of the SCS/TNe Emulation. If the printout is incorrectly double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 186
these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL font - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 187 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 188
Euro Support (IDB Option 139) This SCS Options option controls Euro character printing. Euro character in the EBCDIC code pages. Country Normal code pages Re-mapped code pages USA/Canada 037 1140 Austria/Germany 273 1141 Denmark/Sweden 277 1142 Finland/Sweden 278 1143 Italy 280 1144 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 189
In order to be able to print the Euro character a font supporting the character also has to be selected and available in the printer. See the Download Font (IDB Option 244) option on page 186 : &%IDB_EDIT: OPTION 139:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Euro Support (IDB Option 139) 189 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 190
SCS OPTIONS > CSC CHARACTERS Menu: Options Overview The CSC CHARACTERS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the CSC CHARACTERS menu. SCS OPTIONS > CSC Characters Option name IDB First Char (IDB Option 8) IDB Second Char (IDB - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 191
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in the 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 192 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 193
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in the 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > IDB - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 194 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 195
their values. Option Value : * IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN5250E - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 196
SCS OPTIONS > COR/APO SETTINGS Menu: Options Overview The COR/APO SETTINGS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the COR/APO SETTINGS menu. SCS Options > COR/APO Settings Option name Values Def Page Ori 1 (IDB Option 121) - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 197
Def Page Ori 1 (IDB Option 121) This SCS Options > COR/APO Settings option defines the page orientation for paper tray 1. The option setting is only used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 1 (IDB Option 123) option. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 198
Def Page Ori 2 (IDB Option 122) This SCS Options > COR/APO Settings option defines the page orientation for paper tray 2 and above. The option setting is only used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 2 (IDB Option 124) - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 199
for paper tray 1. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape and Portrait (APO) only, or it can be stated that automatic reduction (COR) is performed after the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 200
When the Disable STO function is selected, all STO commands in the data stream are ignored, i.e. all text orientation commands. Option Value IDB Value Disable 0 Enable APO 1 Enable Auto COR * 2 Disable STO 3 User IDB parameter OFF APO COR STODIS User IDB command: CORDRW 1 : - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 201
tray 2 and above. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape and Portrait (APO) only, or it can be stated that automatic reduction (COR) is performed after the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 202
When the Disable STO function is selected, all STO commands in the data stream are ignored, i.e. all text orientation commands. Option Value IDB Value Disable 0 Enable APO 1 Enable Auto COR * 2 Disable STO 3 User IDB parameter OFF APO COR STODIS User IDB command: CORDRW 2 : - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 203
PPM Quality Dis (IDB Opt.126) This SCS Options > COR/APO Settings option controls the text mode used in the APO/COR function. In the APO/COR function, the print quality parameter is used (text mode on/off) to disable/enable computer output reduction mode. To print in computer output reduction mode, - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 204
. Option Value Off * On Enable APO IDB Value 0 1 2 User IDB parameter Comments OFF Normal IBM interpretation ON Ignore the system TEXT parameter APO Observe TEXT parameter in APO as well User IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 205
COR LSI Reduc (IDB Option 127) This SCS Options > COR/APO Settings option defines the line spacing in Computer Output Reduction mode. The spacing is normally set to 70% of the normal line spacing (100%). Option Value 70% * [1..100] IDB Value 70 User IDB parameter 70 User IDB command: LINSPRED < - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 206
SCS OPTIONS > MISC SETTINGS Menu: Options Overview The MISC SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS>MISC SETTINGS Option name Country Code (IDB Option 2) Codepage (IDB Options 240 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 207
SCS OPTIONS>MISC SETTINGS Option name Lines Per Page (IDB Option 107) Top Margin (IDB Option 108) Source Input (IDB Option 113) Forms Media (IDB Option 114) Output Bin (IDB Option 115) Simplex/Duplex (IDB Option 116) Non-Print Char (IDB Option 3) Values 68 *, range: 1 - 255 1 *, range: 1 - 255 Tray - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 208
migrated from these systems. The International country code forms the basis for all country codes. In country codes other than International country specific characters replace selected characters. Option Value International * USA/Can Ger/Aus Belgium Brazil Can/Fre Den/Nor Fin/Swe France Italy Jap - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 209
Option Value Spain Latin America English (UK) IDB Value 13 14 15 User IDB parameter 13 14 15 User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 210
the code page to be used. Country definition by "Code Page" is commonly used by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 273, 277, 278, 280, 284, 285, 297, 500 and 871 are remapped to the code - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 211
IDB Values (Option 240 and 241) User IDB parameter OCR 340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this line Turkey 1023 255 + 3 1023 USA/Can 1140 116 + 4 1140 Ger/Aus 1141 117 + 4 1141 Den/Nor 1142 118 + 4 1142 Fin/Swe 1143 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 212 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 213
the Font ID. This option setting is usually overwritten by the first control buffer from the system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option Value (Font ID) Font Name 3 OCR-B 11 Courier 10 * 18 Courier It. 10 39 Got - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 214
Option Value (Font ID) Font Name 155 Boldface It 159 Boldface 160 Essay 163 Essay Bold 175 Document 204 Got.Text 13 221 Prestige 15 222 Gothic 15 223 Courier 15 230 Gothic-Text 15 244 Courier 5 245 Courier Bld 5 252 Courier 17 253 Courier Bld 17 281 Got.Text 20 290 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 215
Option Value (Font ID) Font Name 1056 Son.Ser.It 10 1351 Son.Ser. 12 1653 Son.Ser.Bld 16 2103 Son.Ser.Bld 24 IDB Value (Option 242 and 243) User IDB parameter 32 + 4 1056 71 + 5 1351 117 + 6 1653 35 + 8 2103 User IDB command: DEFFNT : Parameter: 3 - 2103 as listed above - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 216
CPI (IDB Option This SCS Options > Misc Settings option selects the CPI (charac100) ters per inch). Option Value 5 CPI 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 5 10 12 15 16 User IDB parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 217
Max Print Pos This SCS Options > Misc Settings option defines the maximum (IDB Option 102) horizontal print position. Option Value 80 * [1..254] IDB Value 80 User IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 218
Left Margin (IDB Option 103) This SCS Options > Misc Settings option defines the left margin in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 219
Right Margin (IDB Option 104) This SCS Options > Misc Settingsoption defines the right margin in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 220
LPI (IDB Option This SCS Options > Misc Settings option selects the number of 105) lines per inch (LPI). Option Value 3 LPI 4 LPI 6 LPI * 8 LPI 9 LPI IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 221
Lines Per Page This SCS Options > Misc Settings option defines the number of (IDB Option 107) lines per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 222
Top Margin (IDB Option 108) This SCS Options > Misc Settings option defines the top margin in lines. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 223
to point to any string. The string pointed to should contain a string which selects a specific tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 224
Forms Media (IDB Option 114) This SCS Options > Misc Settings option selects the paper tray. The setting will trigger definitions made by the Select Media (SLTMED) command. Option Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 225
Output Bin (IDB Option 115) This SCS Options > Misc Settings option selects the paper output bin. The setting will trigger definitions made by the Destination Drawer (DSTDRW) command. Option Value Prtr Setting * Output Bin 1 Output Bin 2 Output Bin 3 IDB Value 0 1 2 3 User IDB parameter DEF 1 2 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 226
tumble setting is used for pages connected or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB parameter DEF SIM DUP TUM User IDB command: DEFSIMDUP - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 227 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 228
for an unprintable character found in the data stream. The character is printed when the host sends an unprintable character or a character not supported by the SCS/TNe Emulation. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of printable characters and their values - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 229
SCS OPTIONS > PAPER SETTINGS Menu: Options Overview The PAPER SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. SCS Options > Paper Settings Option name Left Margin COR (IDB Opt. 78 & 79) Top Margin COR (IDB Opt. 80 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 230
Left Margin COR (IDB Opt. 78 & 79) This SCS options > Paper Settings option defines the offset to be added to the left margin when printing in Computer Output Reduction mode (COR). COR is a feature that allows data processing reports to fit on A4 size paper. 1 inch = 1440. Option Value (1/1440 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 231
The option values for option 78 and 79 are calculated using the formulas below. 79: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 78: (Marg. inch × 1440) - (256 × Value stored in option 79) Round off to nearest whole number. The values stored in - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 232
Top Margin COR (IDB Opt. 80 & 81) This SCS options > Paper Settings option defines the offset to be added to the top margin when printing in Computer Output Reduction mode (COR). COR is a feature that allows data processing reports to fit on A4 size paper. 1 inch = 1440. Option Value (1/1440 inch) - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 233
The option values for option 80 and 81 are calculated using the formulas below. 81: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 80: (Marg. inch × 1440) - (256 × Value stored in option 81) Round off to nearest whole number. The values stored in - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 234
Left Margin Lan (IDB Opt. 86 & 87) This SCS options > Paper Settings option defines the offset to be added to the left margin when printing in Landscape mode. 1 inch = 1440. Option Value (1/1440 inch) IDB Values (Option 86 and 87) User IDB parameter 0 * [0..2880] 0 + 0 0 User IDB command: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 235
The option values for option 86 and 87 are calculated using the formulas below. 87: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 86: (Marg. inch × 1440) - (256 × Value stored in option 87) Round off to nearest whole number. The values stored in - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 236
Top Margin Lan (IDB Opt. 88 & 89) This SCS options > Paper Settings option defines the offset to be added to the top margin when printing in Landscape mode. 1 inch = 1440. Option Value (1/1440 inch) IDB Values (Option 88 and 89) User IDB parameter 147 * [0..2880] 147 + 0 0.10 User IDB command: - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 237
The option values for option 88 and 89 are calculated using the formulas below. 89: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 88: (Marg. inch × 1440) - (256 × Value stored in option 89) Round off to nearest whole number. The values stored in - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 238
Page Length (IDB Opt. 82 & 83) This SCS options > Paper Settings option defines the page length used by the APO/COR (Automatic Page Orientation function/Computer Output Reduction) to calculate page orientation. Option Value (1/1440 inch) IDB Values (Option 82 and 83) User IDB parameter 16848 * - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 239
Parameter 2: Value in inches [0.00 .. 45.51] or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 82:208: OPTION 83:65:EXIT The option values for option 82 and 83 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 240
Page Width (IDB Opt.84 & 85) This SCS options > Paper Settings option defines the page width used by the APO/COR (Automatic Page Orientation function/Computer Output Reduction) to calculate page orientation. Option Value (1/1440 inch) IDB Values (Option 84 and 85) User IDB parameter 11908 * [1.. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 241
Parameter 2: Value in inches [0.00 .. 45.51] or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 84:132: OPTION 85:46:EXIT The option values for option 84 and 85 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 242
TEST OPTIONS Menu: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 243
SCS5250 Hex Dump This Test option enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 244
Print 5250 IDB This Test option prints a report listing the current IDB settings. Print this report when asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 245
SCS5250 This Test option restores the TN5250E SCS OPTIONS settings to Defaults their factory default values. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 246
should only be carried out by authorized technical personal. A complete description is given in the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users can use the Advanced IDB Language to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 247
by job basis. An IDB language is used directly from the AS/400, iSeries or Mainframe host by printing IDB command line sequences on the printer. This is typically done by embedding the unique IDB commands in a normal text document which is printed like any normal job. Alternatively, you can retrieve - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 248
83 and "Operations Reference - TN5250E SETUP" on page 153. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 258 covers IDB commands which can be embedded in the SCS data stream, including details on syntax. IDB - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 249
IDB Languages Usage The two IDB languages work in similar ways. The differences lie in the syntax. When an option is altered with one of the IDB command languages, the configuration data is sent as text to the SCS/TNe Emulation. Rules for configuration data 1 Send the data to the SCS/TNe Emulation - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 250
Syntax The commands used for entering and leaving configuration mode are common to the two languages. Enter configuration mode by sending the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 251
in chapter "Operations Reference TN3270E SETUP" on page 83 and in chapter "Operations Reference - TN5250E SETUP" on page 153. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 258 covers IDB commands which can be embedded in the SCS data stream, including details on syntax. IDB - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 252
editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups. IDB Basics: IDB Configuration File Management 252 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 253
Retrieving the IDB Configuration File The IDB settings controlling how SCS jobs print can be retrieved via FTP. The name of the file is fixed and cannot be changed. The procedure below uses a Microsoft FTP client. To retrieve the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 254 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 255
file is DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File options and events not described in this guide. Only options and events described in this guide should be configured.The IDB configuration file - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 256
Storing the IDB Configuration File When the IDB configuration file has been edited it can be downloaded to the SCS/TNe Emulation. The download file name is fixed. Downloading a file with a different name will result in an unreadable printout. No IDB settings will be changed. The procedure below - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 257 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 258
Commands Using IDB Introduction The IDB commands described here provide additional commands for controlling the printer. This chapter presents the syntax for creating these commands, which must be sent from the AS/400 or iSeries in order to be recognized, i.e. included - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 259
Input Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 260
, it is possible to set up four strings of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 261
initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 261 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 262
8. The events 74 - 78 require programming before they can be used to select a specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 263
Parameter: 1 - 3 Drawer number Example: DSTDRW 2 /1B,"&l2G": DSTDRW DEL 1: PCL command string for setting dest.drawer 2 to bin 1 Delete command string for dest.drawer 1 TN5250e Printer Commands Using IDB: Paper Handling > Destination Drawer 263 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 264
: SLTMED DEL : Delete command Parameter: PAP ENV Select paper media Select envelope media Example: SLTMED PAP "Paper media": SLTMED DEL ENV: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper / Envelope Media 264 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 265
: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper Feed 265 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 267
the symbols and signs are not contained in the normal character set of the printer which means that they cannot be used from AS/400 or iSeries. With this command it is possible to switch to another character set in the printer each time code page 259 is used. This can be used to switch to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 268 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 269
: OVLDRW DEL : Delete command Parameter: 1 - 2 Drawer number Example: OVLDRW 1 /1B,"&f3Y",/1B,"&f2X":PCL string for calling macro no. 3 OVLDRW DEL 1: TN5250e Printer Commands Using IDB: Miscellaneous > Overlay Command 269 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 270 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 271
selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 271 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 272
command is executed on the top of the first page. It may be used for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or company name. The command corresponds to event 96 - 97. Command: SUBTIT : SUBTIT - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 273
DEL: Delete command Example: MOVUPRLIN /1B,"&l0E",/1B,"&a0V":PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to Uppermost Line 273 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 274 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 275
3812-01 (5250 SCS) printer. One TN3270e connection is supported. Up to four TN5250e connections are supported. The SCS/TNe Emulation autodetects installed features to set initial settings for options such as duplex support (TN5250e only). Appendix - Specifications, Requirements, Features: Product - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 276 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 277
AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms 277 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 278
: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 279
and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC character conversion • SCS command conversion • Text string conversion • IBM and 3rd party ASCII transparent modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features: Features List: 5250 SCS - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 280
Appendix B - ASCII Character Table Printable The table shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 282
Appendix C Special TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 283
List of Larger numbers indicate higher precedence. Commands Precedence Command Comments 5 HEXDUMP Enter hex-dump mode (small format) 5 HEXDUMP_FULL Enter hex-dump mode (large format) 5 IDB_EDIT Enter IDB edit mode 5 IDB_PRINT Dump IDB (small format) 5 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 9) if necessary. Appendix - TN3270e IDB Commands: List of Commands 284 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 285
. This is found in fanfold lists which are normally printed on matrix printers with wide platens. The automatic controls can easily be tested by using the CORDRW command. The focus of this discussion is on how the printer automatic controls operate, as the user does not always have the possibility - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 286
that no STO commands are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 287
PAGLNG = A4 and PAGWDT = A4 2 If the page format stated in the FCB is within (or equal to) the page size settings of the PAGLNG and PAGWDT option settings, the page size is "valid". In that case the printout will be in landscape provided the page length is smaller than the width, otherwise it will - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 288
• 10 pitch fonts are reduced to 13 pitch (font type stated in font table position no. 51) • 12 pitch fonts are reduced to 15 pitch (font type stated in font table position no. 52) • 15 pitch fonts are reduced to 20 pitch (font type stated in font table position no. 53) • Other pitch sizes are - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 289
file (CRTPRTF). Please consult your AS/400 or iSeries manuals for information on this subject. Defining the printer file to make the COR is normally done in connection with IPDS page printers as these printers do not support the APO/COR function. If the APO/COR is disabled (CORDRW 1/2 = OFF), the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 290 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 291 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 292
Appendix E Special TN5250e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 293
List of Larger numbers indicate higher precedence. Commands Precedence Command 5 IDB_EDIT 5 IDB_PRINT 5 IDB_PRINT_FULL 5 /... 5 + 5 - 5 {XY}.... 2 1 {XY} 5 IDB_STATUS 5 IDB_FONT 5 -X Comments Enter - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 294
has a programmable font table, which contains the conversion between the IBM font IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR (Computer Output Reduction). The SCS/TNe Emulation will detect free font table - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 295
IBM fonts. The font FGIDs are 3 (OCR-B), 155 (Boldface Italic), 159 (Boldface), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 296
The "Font" Programming Command This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 298
a character spacing command corresponding to the font areas described under . The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM no. 154 - 200). The spacing command should only be used when - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 299
P Selection of "P" causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, and font 10175 is expected to be 100% IBM compatible as to the character spacing: PRGFNT 160 P /1B,"(s1p12.72v0s0b202T": 3 Delete all previous font - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 301
Set Substituted Font ID If a font ID sent from the system is not found in the font table, the font is substituted with a similar font defined in a special area of the font table. The first 7 font positions listed in the status printout (&%IDB_STATUS) represent the substitution fonts for the - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 302
ID 67, but all font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 302 - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 303
Edition Notice SCS/TNe Emulation User's Guide Second Edition October 2007, EC 20G429 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. AND INTERMATE A/S PROVIDE THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 304
Machines Corporation in the United States, other countries, or both. Intelligent Printer Data Stream and IPDS are trademarks or registered trademarks of Ricoh Co., Ltd in the United States, other countries, or both. Lexmark and Lexmark with diamond design, MarkNet and MarkVision are trademarks of - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 305
Started ...1 Documentation Overview ...1 Equipment Requirements and Specifications ...2 Support ...4 Important Configuration Basics ...6 Introduction ...6 What are "IDB Options", "IDB events etc.? ...7 Setup Options vs. Printer Setup Options ...7 Understanding the Control Panel ...9 Introduction - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 306
the SCS/TNe Emulation ...64 Task 5 - Verifying the Host Connection ...69 SCS/TNe Cancel ...71 About Cancel Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 307
101 SCS OPTIONS Menu: Options Overview ...102 COR/APO Sett (IDB Option 122) ...103 SCS Options > MISC SETTINGS Menu: Options Overview 104 FF Support (IDB Option 5) ...106 Non-Print Char (IDB Option 3) ...107 CSC Characters (IDB Options 8 & 9) ...108 IDB Delimiter (IDB Option 7) ...109 Use IR (IDB - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 308
Option 167) ...122 Form Strings (IDB Option 168) ...123 IBM Trn Code (IDB Option 169 bit 1) ...124 Leadin Sequence (IDB Option 169 bit2) ...125 Euro Support (IDB Event 191) ...126 SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview 127 Bold On CR (IDB Option 22 bit 1) ...128 Bold On BS - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 309
(IDB Option 128) ...181 Move Hor/Ver (IDB Option 158) ...183 Format Ctrl Sup (IDB Option 177) ...185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu: Options Overview 190 IDB First Char (IDB Option 8) ...191 IDB Second Char (IDB Option - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 310
Def Page Ori 1 (IDB Option 121) ...197 Def Page Ori 2 (IDB Option 122) ...198 COR Action 1 (IDB Option 123) ...199 COR Action 2 (IDB Option 124) ...201 PPM Quality Dis (IDB Opt.126) ...203 COR LSI Reduc (IDB Option 127) ...205 SCS OPTIONS > MISC SETTINGS Menu: Options Overview 206 Country Code (IDB - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 311
Retrieving the IDB Configuration File ...253 Editing the IDB Configuration File ...255 Storing the IDB Configuration File ...256 Additional TN5250e Printer Commands Using IDB 258 Introduction ...258 Input Data String Syntax ...259 Initializing - Power On Initialize ...260 Paper Handling > Source - Lexmark 782n | SCS/TNe Emulation User’s Guide - Page 312
Specifications, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 275
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA