Lexmark CS410 Printing Guide

Lexmark CS410 Manual

Get Lexmark CS410 PDF manuals and user guides View all Lexmark CS410 manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark CS410 manual content summary:

  • Lexmark CS410 | Printing Guide - Page 1
    Printing guide Page 1 of 8 Printing guide Get the most from the printer by properly loading the trays and properly setting the types and sizes of media. Loading the 250 and 550‑sheet tray The printer has one 250-sheet tray (Tray 1) with an integrated manual feeder. The 250-sheet tray, the 650-sheet
  • Lexmark CS410 | Printing Guide - Page 2
    Printing guide Page 2 of 8 3 Squeeze the length guide tab, and then slide the guide to the correct position for the size of the paper being loaded. 1 2 Note: Use the size indicators on the bottom of the tray to help position the guide. 4 Squeeze and slide the width guide to the correct position for
  • Lexmark CS410 | Printing Guide - Page 3
    side faceup. Printing guide Page 3 of 8 7 Place the paper guides securely against the edges of the paper. 8 Insert the tray. 9 From the printer control panel, 550‑sheet tray, and supports the same paper types and sizes. The only differences are the look of the guide tabs and the location of
  • Lexmark CS410 | Printing Guide - Page 4
    1 Length guide tab 2 Paper size indicator 3 Width guide tab Loading the multipurpose feeder 1 Push the multipurpose feeder latch to the left. 1 2 Printing guide Page 4 of 8 3
  • Lexmark CS410 | Printing Guide - Page 5
    2 Open the multipurpose feeder. Printing guide Page 5 of 8 3 Pull the multipurpose feeder extender. Note: Guide the extender gently so that the transparencies. Be careful not to scratch them. • Flex a stack of envelopes back and forth to loosen them. Straighten the edges on a level surface. Warning
  • Lexmark CS410 | Printing Guide - Page 6
    Printing guide Page 6 of 8 5 Locate the maximum paper fill indicator and tab. Note: Make sure the paper or specialty media is below the maximum paper fill indicator located on the paper guides. 2 1 5 4 3 1 Width guide tab 2 Maximum paper fill indicator 3 Width guide 4 Feeder extender 5 Paper
  • Lexmark CS410 | Printing Guide - Page 7
    not bent or wrinkled. 7 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray. Loading the manual feeder The standard 250‑sheet tray has an integrated manual feeder that can be used to print on different types of paper one sheet
  • Lexmark CS410 | Printing Guide - Page 8
    the paper guide. Printing guide Page 8 of 8 2 Feed paper into the manual feeder only to the point where its leading edge can contact the paper guides. Note: To achieve the best possible print quality, use only high‑quality media designed for laser printers. 3 Adjust the paper guides to the width
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Printing guide
Get the most from the printer by properly loading the trays and properly setting the types and sizes of media.
Loading the 250 and 550
‑
sheet tray
The printer has one 250-sheet tray (Tray 1) with an integrated manual feeder. The 250-sheet tray, the 650-sheet duo tray, and
the 550-sheet tray support the same paper sizes and types and are loaded in the same way.
CAUTION—POTENTIAL INJURY:
To reduce the risk of equipment instability, load each tray separately. Keep all trays
closed until needed.
1
Pull out the tray completely.
Note:
Do not remove trays while a job is printing or while
Busy
appears on the display. Doing so may cause a jam.
2
If the paper is longer than letter
‑
size paper, then push the length guide tab at the back of the tray to extend it.
2
1
Printing guide
Page 1 of 8