Lexmark CS927 Quick Reference
Lexmark CS927 Manual
 |
View all Lexmark CS927 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark CS927 manual content summary:
- Lexmark CS927 | Quick Reference - Page 1
instability, load each tray separately. Keep all other trays closed until needed. 1 Pull out the tray. Note: Do not remove trays while the printer is busy. 2 Adjust the guides to match the size of the paper that you are loading. 3 Flex, fan, and align the paper edges before loading. 4 Load the - Lexmark CS927 | Quick Reference - Page 2
Loading the 2500‑sheet tray The 2500‑sheet tray supports only one paper size, either A4 or letter. To check the supported paper size, pull out the tray and then not remove trays while the printer is busy. • To avoid errors, make sure that the transfer guide is always at the left side of the tray. 2 - Lexmark CS927 | Quick Reference - Page 3
> Configuration Menu > Tray Configuration > Size Sensing. 6 Select the tray and paper size. Loading the 3000‑sheet tray The 3000‑sheet tray supports only one paper size, either A4 or letter. CAUTION-TIPPING HAZARD: To reduce the risk of equipment instability, load each tray separately. Keep all other - Lexmark CS927 | Quick Reference - Page 4
paper jams, make sure that the stack height is below the angle on the frame. Loading the multipurpose feeder 1 Open the multipurpose feeder. 2 Adjust the guide to match the size of the paper that you are loading. 4 Lower the feed roller, and then close the door. 5 From the control panel, navigate - Lexmark CS927 | Quick Reference - Page 5
1 Depending on the operating system, do either of the following: • Open the printers folder, and then select your printer. • From the System Preferences in the Apple menu, navigate to your printer. 2 Select the job to cancel. Maintaining the printer Replacing a toner cartridge 1 Open door A. 5 - Lexmark CS927 | Quick Reference - Page 6
2 Remove the toner cartridge. 4 Shake the toner cartridge three times. 5 Insert the new toner cartridge. 3 Unpack the new toner cartridge. 6 - Lexmark CS927 | Quick Reference - Page 7
6 Remove the waste toner bottle. 7 Using the printhead wiper, clean the printhead lens. 9 Insert the waste toner bottle, and then close the door. 8 Insert the wiper back into place. 7 Clearing jams Avoiding jams Load paper properly • Make sure that the paper lies flat in the tray. - Lexmark CS927 | Quick Reference - Page 8
, allow the surface to cool before touching it. • Make sure that the paper guides are positioned correctly and are not pressing tightly against the paper or envelopes. • Push the tray firmly into the printer after loading paper. Use recommended paper • Use only recommended paper or specialty media - Lexmark CS927 | Quick Reference - Page 9
• Fuser area • Duplex area • Below the fuser area Notes: • Make sure that the door does not hit any cable attached to the printer. • If a 3000‑sheet tray is installed, then slide the tray to the right to open the door. 2 Remove the jammed paper from any of the - Lexmark CS927 | Quick Reference - Page 10
Paper jam in door D 1 Open door D, and then remove the jammed paper. Note: Make sure that all paper fragments are removed. 4 Close the trays, and then close the door. 3 Close the tray, and then close the door. Notes: • If a 3000‑sheet tray is installed, then slide the tray to the right to open
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
Quick Reference
Loading paper
Loading trays
CAUTION—TIPPING HAZARD:
To reduce the risk of
equipment instability, load each tray separately. Keep all
other trays closed until needed.
1
Pull out the tray.
Note:
Do not remove trays while the printer is busy.
2
Adjust the guides to match the size of the paper that you are
loading.
3
Flex, fan, and align the paper edges before loading.
4
Load the paper.
•
When using letterhead, do either of the following:
Without an optional finisher
With an optional finisher
One
‑
sided printing
One
‑
sided printing
Two
‑
sided printing
Two
‑
sided printing
One
‑
sided printing
One
‑
sided printing
1