Lexmark T644 SCS/TNe Emulation User’s Guide
Lexmark T644 Manual
 |
UPC - 845307525920
View all Lexmark T644 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark T644 manual content summary:
- Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 1
/TNe Emulation User's Guide Getting Started SCS/TNe in a LAN environment IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Thank you for purchasing the Card for IPDS and SCS/TNe. The card provides high quality IBM host connectivity print output - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 2
Requirements and Specifications IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Supported Products With the appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C770, C772 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 3
called STD Net). • MarkNet internal print server (Ethernet). If you need to update your Standard Network or MarkNet firmware, refer to "Support" on page 4. For further information on requirements and specifications, see the appendix starting on page 275. Getting Started: Equipment Requirements and - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 5
This page is intentionally left blank Support: Customer Support 5 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 6
refers to printers and MFPs, and the term control panel refers to operator panels and touch screens on these types of products. SCS/TNe MENU options settings can be changed and saved in three ways: • Use the control panel ("Understanding the Control Panel" on page 9 - which also contains all - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 7
IPDS, PostScript™ or PCL™ jobs. The SCS/TNe Emulation user default settings remain in effect until you save new settings or restore the factory defaults by using one of the SCSxxxx Defaults options under MENU/Menus > Option Card Menu > SCS/TNe MENU > TNxxxE STEUP > TEST OPTIONS. xxxx stands for 3270 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 8
Restoring the factory defaults using the printer MENU/Menus > Settings > Utilities Menu > Restore Defaults does not affect the SCS/TNe MENU settings. Settings you choose in the SCS print job may override the user default settings displayed in the printer operator panel. This guide discusses setting - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 9
Understanding the Control Panel Introduction This chapter introduces the SCS/TNe MENU options as well as illustrating how how the control panel works. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs are illustrated here. If you are familiar with the use of - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 10
checkmark is displayed next to it. The same method is used to scroll through lists of menu groups and options. As you move through the menus, the top line in the screen shows the menu or menu group name to which the displayed items belong. Understanding the Operator Panel: Printer operator panel - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 11
until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator panel" on page 10. 2 Use the navigation buttons or to - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 12
the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP 9 TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK 9 SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 13
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS 9 MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup 9 Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 13 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 14
the list. When the on-screen checkmark is next to the desired setting. press the Select button Country Code English (US) 9 Fin/Swe Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel: Printer operator panel 14 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 15
menu group, press the Back button and then use the navigation buttons and press Select. 9 When you are finished, exit by pressing the Back button to return to the Ready screen. You may need to press it several times until the screen appears. Understanding the Operator Panel: Printer operator - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 16
display: MSGQ 1 Name Q S Y O P R The currently editable character is marked with below it. above it and Use the navigation buttons and to move between the characters. To store the new string, press Select after entering all the characters. Understanding the Operator Panel: Printer - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 17
a menu item that has a numerical value, you can usually choose between scrolling just as you would to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 16. Understanding the Operator Panel: Printer operator - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 18
the operScreen ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer is on and the Ready message appears. 2 Touch the key icon (Menus) on the operator panel 3 Touch or to scroll through the main menus displayed on the screen. 4 Touch Option - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 19
User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "MFP Touch Screen" on page - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 20
or to scroll to the desired item. In this example locate and touch Country Code. 7 The currently active setting, in this example English (US), is always presented first. without making changes, touch (Back) and no changes will be saved. Understanding the Operator Panel: MFP Touch Screen 20 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 21
9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e Setup > Network Setup > Server Info. 2 Touch the Keyboard symbol by LU Name. A keyboard similar to a typwriter - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 22
previous menu level. Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 23
, the term printer in this manual refers to both printers and MFPs. The Card for IPDS and SCS/TNe includes an http user interface. You each printer, either from a browser or via the operator panel. How Remote Configuration Works All option values which may be changed remotely will be displayed in - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 24
printer web page by typing the IP address of its print server as the URL. 2 Select Configuration. 3 Select SCS/TNE Settings. 4 Select the TNe Common menu display returns to SCS/TNe Settings. 7 Check to be sure that all sessions have been disconnected. Click on each TNxxxx Connection Status menu - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 25
session from the host. If no jobs are printing, you may need to end and reset the session at the host. 8 Return to SCS/TNe Settings. 9 Select one of the TN3270E or TN5250E menus. 10 All option values which may be changed remotely will be displayed. Change option settings as desired. 11 Select the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 26
steps 14 - 16. On each TN menu, you will see a Reset Form button at the bottom of the page, next to the Submit button. If you have entered values in the page without submitting, and decide to start all over again, click Reset Form. The page will then display the values that were current when you - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 27
latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For TN3270e Printing Task 3 -Configuring a Print Server Task 4 - Configuring the SCS Settings Task - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 28
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 28 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 29
described in IBM's VTAM documentation. The Mainframe software must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. "Mainframe Software" on page 277 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 30
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE,IRETRY=YES,IDNUM=B0008, PASSLIM=7,PUTYPE=2,DISCNT=NO,VPACING=0 LCPG90 LU LOCADDR=2,MODETAB=MT3274P,USSTAB=USB3274B, DLOGMOD=T3274M2 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 31
Sample Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or terminal devices) for telnet sessions as follows: TCP VBUILD TYPE=APPL SC0TCP01APPL AUTH=NVPACE, EAS=1, PARSESS=NO, MODETAB=ISTINCLM, SESSLIM=YES - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 32
member (i.e. IMLU1 listed above) to the host print software being used. The following is an example of a TN printer definition defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 33
Task 1B Configuring the Host for Printing via a SNA Server TIP: How to define an LU-1 printer in VTAM is described in IBM's VTAM documentation. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Two sample configurations are shown below. Sample - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 34
LOACADDR=4,MODETAB=MTP3816, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 34 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 35
book OS/390 eNetwork Communications Server V2R5, TCP/IP Implementation Guide, Volume 1: Configuration and Routing (document no. SG24-5227-00). The printer with the SCS/TNe Emulation is defined to the Telnet server in much the same way as a display LU. Instead of the LUGROUP and LUMAP commands, the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 36
ENDPRTGROUP IPGROUP SPECIP 157.184.116.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 37
group as shown above (PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 38
Task 2B Configuring an SNA Server For TN3270e Printing IMPORTANT: The TN3270e components have to be installed in order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways and routers. The procedure in this section shows - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 39
created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 40
. 3 Scroll until one or more of the following appears. If none of these appear, then you do not have a Standard Network or internal print server installed. a If Network Setup Page appears, touch it. This prints the Standard Network Card menu settings page. b If Network # Setup Page appears, touch it - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 41
may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus > Network/Ports. Select the print server to be used for SCS printing, for example Standard Network, Network 1, or Network 2. Locate NPA Mode and scroll to the Auto setting. Touch - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 42
Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network administrator. Enable DHCP On DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 42 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 43
Operations Reference - TN3270E SETUP: SCS3270 Defaults, page 151 to see the differences in these settings. A. To select Non-US SCS3270 Defaults Factory defaults are US. To change or restore: 1 Select Menus > Option Card Menu > SCS/TNe MENU to save one of the factory defaults. 3 Exit the menu by - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 44
Value Country Code (IDB Option 2) English (US) Recommended Value Comments Your preferred country 2 Scroll to the desired value. Touch SelectSubmit to save one of the factory defaults. 3 Exit the menu by pressing touching Home. C. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 45
/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. SCS jobs are printed from a LAN connected Mainframe using TCP/ IP and the telnet extended - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 46
in section "NETWORK SETUP> SERVER INFO Menu: Options Overview" on page 93. SERVER INFO Option Name / IP Address IP Address Hostname TN Server Port Default Value Recommended Value Comments Use IP Address Check with your system administrator whether you need to specify the specific IP address or - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 47
Some hosts and servers only recognize uppercase LU Names. Specific Check with your system administrator for the correct setting Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes and touch Submit to save. 4 Exit the menu - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 48
/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. Wait approximately one minute. If all values are set correctly, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect Status from Print - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 49
to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 90) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu >SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 50
in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. 3 From the main frame host give the following TCP/IP display command: D TCPIP,TCPIPNAME,TELNET,CONNECTION,PORT - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 51
to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 90) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 52
printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 53
obtain the latest version of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring the SCS Settings Task - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 54
Task 1 Configuring the Host The host operating system must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 277 lists host software which supports these protocols. To configure the host check and set the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 55
System Value QAUTOVRT Required Value Controls the automatic configuration of virtual devices. Must be set to an adequate number of devices Sample commands: DSPSYSVAL QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 56
. 3 Scroll until one or more of the following appears. If none of these appear, then you do not have a Standard Network or internal print server installed. c If Network Setup Page appears, touch it. This prints the Standard Network Card menu settings page. d If Network # Setup Page appears, touch it - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 57
may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus > Network/Ports. Select the print server to be used for SCS printing, for example Standard Network, Network 1, or Network 2. Locate NPA Mode and scroll to the Auto setting. Touch - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 58
. Netmask for your network. Contact your network administrator. Address of the IP gateway. Contact your network administrator. On or Off On, if you use a DHCP server. Off, if you set the IP address another way. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 58 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 59
setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 59 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 60
print SCS jobs which do not contain formatting commands in the job. The SCS/TNe Emulation comes with European (A4 paper size) factory default settings. The following five settings are usually the most important, but there are many other possibilities. IMPORTANT: One set of TN5250e SCS OPTIONS menu - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 61
Submit to save it. Option Lines Per Page (IDB Option 107) Default Value 68 (for A4) Recommended Value Comments 64 (for Letter). 82 (for Legal). Recommended values for users in the USA 4 (Select other settings within MISC SETTINGS) 5 Exit the MISC SETTINGS menu by touching Home. AS/400 and - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 62
(for A4) Recommended Value Comments 12240 (for Letter). Recommended value for users in (same for Legal). the USA 8 Exit the PAPER SETTINGS menu by touching Back. 9 Change other settings as desired. 10 Exit the menu by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 63
(IDB Option 139) B. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and iSeries - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 64
end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. SCS jobs are printed from a LAN connected AS/400 or iSeries host using TCP/IP and - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 65
SERVER # INFO Menu: Options Overview" on page 163. Option Default Value Name / IPaddress # Use IP# Address IP # Address 0.0.0.0 Hostname # [undefined] Server # TN Port 23 Recommended Value Comments Check with your system administrator whether you need to specify the specific IP address or - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 66
name if it does not exist. None or own preference Leave this at the factory default if the host is configured to send a keep alive signal. Choose a . Normal Leave this option at its default value to have printer intervention required conditions reported to the host. AS/400 and iSeries - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 67
> Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION # > Print # Active. Scroll to Yes and touch Submit to save. 7 Exit the menu by touching Home. 8 To activate the new settings, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 68
Wait approximately one minute. If all values are set correctly, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 90. AS/400 and iSeries - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 69
the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN5250E Connection Status (see page 160). From the Operator Panel: Display the TN5250E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN5250 SETUP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 70
printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 71
Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be the job which is canceled - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 72
the Select button on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only one Print Job shown, as in - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 73 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 74
MFP Cancel Job 1 While any job is printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected Job icon. 4 The screen will display a message to indicate - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 75
the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN Session • SCS Debug Trace Operations - Common Setup: Introduction - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 76
for each option on the Menu Settings page. • From the Operator Panel: Select Menus > Reports > Menu Settings Page. • Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Reports and choose - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 77
Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows. Operations - Common Setup: Menu Options Overview - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 78
Disconn. Do not disconnect any sessions. This performs the same action as if Back had been pressed in the operator panel. Disconnect Ses. Disconnect ALL active TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must be performed before the SCS/TNe Emulation will attempt to - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 79
have been made to the Network or Server Info settings to disconnect and reconnect using the new settings. Operator panel text Comments Do Not Reset Do not reset any settings. This performs the same action as if Back had been pressed in the operator panel. Reset TN Ses. Disconnect ALL active - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 80
to receive the trace data, the printer will remain Ready and may not menu option allows you to enable tracing and choose where the trace data should be sent. Because tracing will decrease printing performance, it should only be enabled when needed by service personnel for troubleshooting and service - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 81
output. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be added to provide additional ports for output of the debug trace data. Operations - Common Setup: SCS Debug Trace 81 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 82
same action as if Back had been pressed in the operator panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 83
Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TNE3270E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the TN3270E SETUP menu. Operations - TN3270E SETUP: Introduction 83 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction TN3270E SETUP NETWORK SETUP Print Active TN3270 Defaults Connect Status SCS OPTIONS COR/APO Sett TEST OPTIONS SCS3270 Hex Dump Print 3270 IDB SCS3270 Defaults SERVER INFO Name/IPaddress IP Address - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 85
job. If one or more SCS settings are missing from a job, the SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu for the operator panel to indicate the current setting. The Menu Settings page shows the text string "[invalid]" for options set outside their ranges. Invalid will print - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 246 ff.) Operations - TN3270E SETUP: Introduction 86 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 87
to Connect Status (page 90) for a description of each message. Sub-menu. See NETWORK SETUP> SERVER INFO Menu: Options Overview (page 93) and Name / IP Address (page 94). A description of each NETWORK SETUP menu option follows. Operations - TN3270E SETUP: NETWORK SETUP Menu: Options Overview 87 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 88
Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active 88 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 89
default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN3270e NETWORK SETUP menu options to factory default settings - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 90
Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports > print server to be used for SCS printing > NPA Mode). 3 Cable is not plugged into print server. Plug in cable. 4 Network is down. Check network. Operations - TN3270E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 91
support for that device-type Lst Rsp:Name unknown to server Lst Rsp:The requested device is in use Lst Rsp:Terminal/Printer printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 91 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 92
SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has occurred. Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 92 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 93
to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 *, range: 1 - 32000 [seconds] A description of each SERVER INFO menu option follows. Operations - TN3270E SETUP: NETWORK SETUP> SERVER INFO Menu: Options Overview 93 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to IP address specified with the IP Address option. Use the hostname specified with the Hostname option. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Name / IP Address 94 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > IP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 96
/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Hostname 96 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 97
TN Server Port This Network Setup > Server Info option specifies the TCP Telnet server port defined on the host. Check selected. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN Server Port 97 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 98
option or on the Menu Settings page ( "How to access the Menu Settings Page" on page 76). Check with your system administrator for the correct LU name to use. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 99
a specific LU name. Make sure this has been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU names. Operations - TN3270E SETUP: NETWORK - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 100
alive signal. The SCS/TNe Emulation can receive and respond to a Telnet NOP or a Timing Mark keep alive signal. Send a Telnet No Operation as the keep alive signal. Send a Telnet timing mark as the keep alive signal. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep Alive Type 100 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive Type is set to None. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep Alive Time 101 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 102
MISC SETTINGS Menu: Options Overview (page 104) and FF Support (IDB Option 5) (page 106). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 131) and Left Margin (IDB Option 103) (page 133). A description of each of the SCS OPTIONS menu item follows. Operations - TN3270E SETUP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 103
based on page formatting commands received from the host. If the document does not fit on a page in portrait orientation, the orientation is changed to landscape. Option Value No Yes * IDB Value 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:2:EXIT Operations - TN3270E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 104
the MISC SETTINGS menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters (IDB Options 8 & 9) IDB Delimiter (IDB Option 7) Use IR (IDB Option 21) Format Ctrl Sup (IDB Option 177) Country Code (IDB Option 2) Skip Blank Page (IDB Option 32 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 105
No Translation Normal *, Without '&%' No *, Yes Sub-menu. See SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview (page 127) and Bold On CR (IDB Option 22 bit 1) (page 128). A description of each MISC SETTINGS menu item follows. Operations - TN3270E SETUP: SCS Options > MISC SETTINGS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 106
when the MPL (Maximum Page Length) or BM (Bottom Margin) is reached in the data stream. Option Value Always FF * Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 106 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 107
Table" on page 280 for a complete list of printable characters and their values. Option Value ASCII Value 45 * ASCII Value [0..255] IDB Value 45 0 - 255 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Non-Print Char (IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 108
used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. language to set factory default: &%IDB_EDIT: OPTION 8:38,37:EXIT Operations - TN3270E SETUP: - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 109
Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon (:)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IDB Delimiter (IDB Option - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 110
are sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 21:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 111
print and Local Copy print. It can be enabled with the -M command. All host generated codes are still sent. Is diabled after Power On in Host direct print codes are suppressed, horizontal/vertical tab and other commands which depend on correct page format will not work correctly. Operations - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 112
NL function is still enabled. NOTE: = &% is factory default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 113
the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: After this command, all Host generated control codes are processed and the auto-NL function operates as normal. Refer to "Appendix C - Special TN3270e IDB Commands" on page 282 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 114
Country Code (IDB Option 2) This SCS Options > MISC Settings option defines the character set. Option Value , U.K. English, U.S. See note. Finnish/Swedish Finnish/Swedish Alternate French/Azerty 105 International Italian Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 114 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 115
the SCS options are restored to non-US factory defaults, the default value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:1:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 115 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 116
controls whether or not blank pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 32:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 117
100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI (IDB Option 100) 117 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 118
> MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos (IDB Option 102) 118 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 119 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 120 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 121
per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:64:EXIT Operations - TN3270E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 122
> MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency (IDB Option 167) 122 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 123
Table" on page 280 for a complete list of printable characters and their values. Option Value ASCII Value 0 * ASCII Value [1..255] IDB Value 0 1 - 255 Comments Disable the Formatted String Utility. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 168:0:EXIT Operations - TN3270E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 124
No translation from EBCDIC to ASCII is performed. All transparent data is printed, even invalid data, ie data in the range 40H - FEH. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IBM Trn Code (IDB Option 169 bit 1) 124 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 125
defined trans- parent handling. 1 User defined transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options 8 & 9) option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 126
option controls Euro character (IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E SETUP: MISC SETTINGS > Euro - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 127
the BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS (IDB Option 22 bit 2) Bold On Multi BS (IDB Opt. 22 bit 3) Values Yes *, No Yes *, No Yes *, No A description of each BOLD PRINT menu option follows. Operations - TN3270E SETUP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 128
option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On CR (IDB Option 22 bit - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 129
option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On BS (IDB Option 22 bit 2) 129 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 130
This SCS Options > MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 131
*, Landscape, COR Portrait *, Landscape, COR Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 131 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 132 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 133
. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Left Margin (IDB Option 103) 133 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 134
character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:132:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Right Margin (IDB Option 104) 134 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 135
margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Top Margin (IDB Option 108) 135 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 136
default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 109:64:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Bottom Margin (IDB Option 109) 136 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 137
Feed paper from the paper source selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from Tray 4 Paper is fed from Tray 5 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 113:1:EXIT Operations - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 138
Tray 1 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 139
Tray 2 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 140
Tray 3 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 141
Tray 4 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 142
Tray 5 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 143
This paper size is used to determine the print area factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 90:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray1 Paper - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 144
This paper size is used to determine the print area factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 91:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray2 Paper - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 145
This paper size is used to determine the print area factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 92:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray3 Paper - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 146
This paper size is used to determine the print area factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 93:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray4 Paper - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 147
This paper size is used to determine the print area factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 94:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray5 Paper - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 148
under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print SCS3270 Defaults Do Not Restore *, US-Default, Non-US-Default A description of each TEST OPTIONS menu item follows. Operations - TN3270E SETUP: TEST OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 149
print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes Dump-Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN3270E SETUP: TEST OPTIONS > - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 150
IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. Advanced IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 151
US and the Non-US factory default settings. Affected option Country Code (IDB Option 2) Bottom Margin (IDB Option 109) LPP (IDB Option 107) Tray1 Paper Size (IDB Option 90) US-Default Non-US-Default English (US) English (UK) 64 66 64 66 Letter A4 Operations - TN3270E SETUP: TEST OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 152
(IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always FF Yes Operations - TN3270E SETUP: TEST - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 153
Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TN5250E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the TN5250E SETUP menu. Operations - TN5250E SETUP: Introduction 153 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 154
PAPER SETTINGS MISC SETTINGS COR/APO SETTINGS CSC CHARACTERS Lef Margin COR Top Margin COR Lef Margin Lan Top Margin Lan Page Length Page Width Country Code Codepage Font CPI Max Print Pos Left Margin Right Margin LPI Lines Per Page Top Margin Source Input Forms Media Output Bin Simplex/Duplex - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 155
job. If one or more SCS settings are missing from a job, the SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu for the operator panel to indicate the current setting. The Menu Settings page shows the text string "[invalid]" for options set outside their ranges. Invalid will print - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 156
for the User IDB language and another for the Advanced IDB language. These show how to remotely set the menu option to the factory default or how to perform the described action (cf. "IDB Basics" on page 246 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 258 ff.) Operations - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 157
. Refer to Connect # Status (page 160) for a description of each message. SERVER # INFO Sub-menu. See CONNECTION # > SERVER # INFO Menu: Options Overview (page 163) and Name / IPaddress # (page 164). A description of each CONNECTION## menu option follows. Operations - TN5250E SETUP: CONNECTION - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 158
communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN5250E SETUP - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 159
#2, #3, or #4 factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN5250 CONNECTION ## menu options for the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 160
. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports > print server - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 161
. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. could not establish a session. Check with system operator. Check with system operator. Check with system operator. The SCS/TNe Emulation device is not varied ON - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 162
8918:Job canceled Lst Rsp:8920:Object partially damaged Lst Rsp:8921:Communication error Lst Rsp:8922:Negative response received Lst Rsp:8923:Start-up record . Check with system operator. Check with system operator. Check with system operator. Check with system operator. An exisisting device - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 163
. Check with system operator. Check with system operator. Check with system operator. Check with system operator. CONNECTION # > SERVER # INFO Menu: Options Overview Each SERVER # INFO menu is a sub-menu under the corresponding CONNECTION # menu. The following table lists menu options found under - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 164
, No Reply Auto Sense # END No *, Yes A description of each SERVER # INFO menu option follows. Name / This Connection# > Server# Info option specifies the kind of IPaddress specified with the Hostname # option. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Name / IPaddress # 164 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 165
This Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IP # Address - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 166
/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Hostname # 166 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 167
the Internet. Any number within this range can be selected. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server # TN Port 167 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 168
will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Device # Name 168 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 169
to send a keep alive signal. The SCS/TNe Emulation can receive and respond to a Telnet NOP or a Timing Mark keep alive signal. Send a Telnet No Operation as the keep alive signal. Send a Telnet timing mark as the keep alive signal - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 170
than the session's inactivity timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires range is 1 to 32000 seconds. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Time 170 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 171
at the default if you do not know the message queue name. Option Value QSYSOPR * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ # Name 171 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 172
option at the default if you do not know the library name. Option Value *LIBL * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ # Lib 172 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 173
No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the use of IR replies. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IR # Reply 173 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 174
necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer ends, reconnect, and reconfigure automatically. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Auto Sense - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 175
Hor/Ver (IDB Option 158) Use Escape *, Use Line feed, Space + Escape, Linefeed + Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 175 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 176
206) and Country Code (IDB Option 2) (page 208). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options Overview (page 229) and Left Margin COR (IDB Opt. 78 & 79) (page 230). A description of each SCS OPTIONS menu item follows. Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 176 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 177
2 will be executed if paper tray 2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: OVLCAL OFF:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 178 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 179
proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which Use * Use IDB Value 0 1 User IDB parameter OFF ON User IDB command: PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E SETUP: SCS OPTIONS > Prop - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 180 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 181
is used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 10 CPI, 96 characters Option Value Off * On IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 182 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 183
VERMOV : Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 183 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 184 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 185
Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: CTLCODSUP ON:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 177:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 186
that these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 187 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 188
pages Re-mapped code pages USA/Canada 037 1140 Austria/Germany 273 1141 Denmark/Sweden 277 1142 Finland/Sweden 278 1143 Italy 280 1144 Spain 284 1145 UK 285 1146 France 297 1147 Multinational 500 1148 Iceland 871 1149 Operations - TN5250E SETUP: SCS OPTIONS > Euro Support - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 189
be able to print the Euro character a font supporting the character also has to be selected and available in the printer. See the Download Font (IDB Option 244) option on page 186 and the Font (IDB Options 242 and 243) option on page 213. Option Value No * Yes IDB Value 0 1 User IDB parameter OFF - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 190
in the decimal range: 33 - 126 : * (ASCII character 58 [colon]), any single ASCII character in the decimal range: 33 - 126 A description of each CSC CHARACTERS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > SCS OPTIONS > CSC CHARACTERS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 191
also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value page 280 for a complete list of characters and their values. Option Value & * IDB Value 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 192 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 193
also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value page 280 for a complete list of characters and their values. Option Value % * IDB Value 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 194 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 195
: * IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 196
PPM Quality Dis (IDB Opt.126) Off *, On, Enable APO COR LSI Reduc (IDB Option 127) 70% *, range: 1 - 100 [%] A description of each COR/APO SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 197
command: ORTDRW 1 : Parameter: DEF, POR, LAN User IDB language to set factory default: &%IDB_EDIT: ORTDRW 1 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 121:1:EXITz Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > Def Page Ori 1 (IDB Option 197 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 198
IDB command: ORTDRW 2 : Parameter: DEF, POR, LAN User IDB language to set factory default: &%IDB_EDIT: ORTDRW 2 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:1:EXI Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > Def Page Ori 2 (IDB Option 198 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 199
option defines how the APO/COR function (Automatic Page Orientation/Computer Output Reduction) works for paper tray 1. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 200
command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 201
option defines how the APO/COR function (Automatic Page Orientation/Computer Output Reduction) works for paper tray 2 and above. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 202
command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 203
mode is disabled, the APO/COR function will ignore the print quality parameter and print all print jobs fulfilling the requirements in computer output reduction mode. Refer to "Appendix D - COR/APO Logic (TN5250e)" on page 285 Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 204
Observe TEXT parameter in APO as well User IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 205
: LINSPRED : Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default: &%IDB_EDIT: LINSPRED 70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:70:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR LSI Reduc - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 206
menu. SCS OPTIONS>MISC SETTINGS Option name Country Code (IDB Option 2) Codepage (IDB Options 240 and 241) Font (IDB Options 242 and 243) CPI (IDB Option 100) Max Print : 1 - 255 6 LPI *, 3 LPI, 4 LPI, 8 LPI, 9 LPI Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS Menu: Options Overview 206 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 207
Prtr Setting *, Paper Media, Envelope Med Prtr Setting *, Output Bin 1, Output Bin 2, Output Bin 3 Prtr Setting *, Simplex, Duplex, Duplex (Tumble) ASCII Value 45, any single ASCII character in the decimal range: 0 - 255 A description of each MISC SETTINGS menu option follows. Operations - TN5250E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 208
country specific characters replace selected characters. Option Value International * USA/Can Ger/Aus Belgium Brazil Can/Fre Den/Nor Fin/Swe France Italy Jap (Latin) USA/Can bil. Portugal IDB Value 0 1 2 3 4 5 6 7 8 9 10 11 12 User IDB parameter 0 1 2 3 4 5 6 7 8 9 10 11 12 Operations - TN5250E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 209
13 14 15 User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 210
241) This SCS Options > Misc Settings option defines the code page to be used. Country definition by "Code Page" is commonly used by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 273, 277, 278, 280, 284, 285, 297, 500 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 211
and 241) User IDB parameter OCR 340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this line 124 + 4 1148 Iceland 1149 125 + 4 1149 User IDB command: DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 212 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 213
in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. User IDB parameter 3 + 0 3 11 + 0 11 18 + 0 18 39 + 0 39 40 + 0 40 46 + 0 46 66 + 0 66 68 + 0 68 69 + 0 69 85 + 0 85 87 + 0 87 110 + 0 110 111 + 0 111 112 + 0 112 Operations - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 214
Ser. 7 1051 Son.Ser. 10 1053 Son.Ser.Bld 10 IDB Value (Option 242 and 243) User IDB parameter 155 + 0 155 159 + 0 159 160 + 0 160 163 + 0 163 290 239 + 2 751 27 + 4 1051 29 + 4 1053 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 214 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 215
IDB command: DEFFNT : Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 242:11: OPTION 243:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 216
IDB parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 217
IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:80:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Max Print Pos (IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 218
1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 219
1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 220
9 LPI IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT: DEFLPI 6:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN5250E SETUP: SCS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 221
per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:68:EXIT Operations - TN5250E - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 222
1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 223
which selects a specific tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set factory default - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 224
IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory default: &%IDB_EDIT: DEFFRMSEL DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 114:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Forms Media (IDB Option 114 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 225
3 IDB Value 0 1 2 3 User IDB parameter DEF 1 2 3 User IDB command: DEFDSTDRW : Parameter: DEF, 1, 2, 3 User IDB language to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 115:0:EXIT Operations - TN5250E SETUP: SCS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 226
(SLTSIMDUP) command. The tumble setting is used for pages connected or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB parameter DEF SIM DUP TUM - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 227 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 228
: All EBCDIC characters or a printable ASCII hex value User IDB language to set factory default: &%IDB_EDIT: UNPCHR /2D:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Non-Print Char (IDB Option 3) 228 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 229
(IDB Opt. 82 & 83) Page Width (IDB Opt.84 & 85) Values 634 *, range: 0 - 2880 0 *, range: 0 - 2880 0 *, range: 0 - 2880 147 *, range: 0 - 2880 16848 *, range: 1 - 65535 11908 *, range: 1 - 65535 A description of each PAPER SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 230
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 78:122: OPTION 79:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 231
are calculated like this: 79: 0----.-4----4---0-----×-----1---4---4----0-256 ≈2 78: (0.440 × 1440) - (256 × 2) ≈ 122 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 & 231 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 232
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 80:0: OPTION 81:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 233
of 1 inch are calculated like this: 81: 1-----×-----1---4----4---0-256 ≈5 80: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & 233 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 234
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 86:0: OPTION 87:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 235
of 1 inch are calculated like this: 87: 1-----×-----1---4----4---0-256 ≈5 86: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 & 87) 235 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 236
] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 88:147: OPTION 89:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 237
calculated like this: 89: 0----.-1----0---2-----×-----1---4---4----0-256 ≈0 88: (0.102 × 1440) - (256 × 0) ≈ 147 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt. 88 & 89) 237 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 238
29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 238 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 239
115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 82 by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 239 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 240
in cm 21.00 21.59 21.59 18.42 Width in inch. 8.27 8.50 8.50 7.25 Option value 11908 12240 12240 10440 User IDB command: PAGWDT : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 240 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 241
115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 84 by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 241 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 242
found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print SCS5250 Defaults Do Not Restore *, Restore Defaults A description of each TEST OPTIONS menu option follows. Operations - TN5250E SETUP: TEST OPTIONS - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 243
print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes Dump-Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN5250E SETUP: TEST OPTIONS > - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 244
asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. User IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN5250E SETUP: TEST - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 245
. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu settings. Operations - TN5250E SETUP: TEST OPTIONS > SCS5250 Defaults 245 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 246
are programmed using the IDB language. IDB is short for Intermate Data Base and refers to the SCS/TNe Emulation's storage of all SCS protocol Reference guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users can - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 247
is somewhat easier to use. However, the User IDB Language is only available for working on approximately used directly from the AS/400, iSeries or Mainframe host by printing IDB command line sequences on the printer. This is typically done by embedding the unique IDB commands in a normal text - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 248
the Control Panel" on page 9 ff. "Operations Reference - TN3270E SETUP" on page 83 and "Operations Reference - TN5250E SETUP" on page 153. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 258 covers IDB commands - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 249
an option is altered with one of the IDB command languages errors are ignored. If the SCS/TNe Emulation prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 250
Syntax The commands used for entering and leaving configuration mode are common to the two languages. Enter configuration mode by sending the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 251
Programming examples Advanced IDB (TN3270E + TN5250E) User IDB (TN5250E) Valid &%IDB_EDIT: &%IDB_EDIT: - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 252
of all IDB options and events are viewed and edited on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 253
IDB Configuration File The IDB settings controlling how SCS jobs print can be retrieved via FTP. The name of the file file. get tn3270e.idb c:\tn3270e.idb (TN3270E users) get tn5250e.idb c:\tn5250e.idb (TN5250E users) This stores the file on the PC in the root directory c:. IDB Basics: Retrieving - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 254 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 255
Editing the IDB Configuration File The utility program used for editing the IDB configuration file is DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File TN3270E P01-xxxx.zip TN5250E P02-xxxx.zip Comments - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 256
. The download file name is fixed. Downloading a file with a different name will result in an unreadable printout. No IDB settings will be changed. The procedure below uses a Microsoft FTP client. To store the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 257 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 258
recognized, i.e. included in the SCS data stream. The commands you may work with fall into three groups: 1 Paper Handling 2 Code Page Handling / Code Page 259 3 Miscellaneous See "IDB Basics" on page 246 ff. for background information on IDB. TN5250e Printer Commands Using IDB: Introduction 258 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 259
Input Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 260
of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected. 3 DEFCPI (CPI) (option 100) triggers - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 261
initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 261 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 262
74 - 78 require programming before they can be used to select a specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command Parameter - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 263
Parameter: 1 - 3 Drawer number Example: DSTDRW 2 /1B,"&l2G": DSTDRW DEL 1: PCL command string for setting dest.drawer 2 to bin 1 Delete command string for dest.drawer 1 TN5250e Printer Commands Using IDB: Paper Handling > Destination Drawer 263 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 264
This is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when printing on paper or envelopes is selected. It can also be triggered by the DEFFRMSEL command at Power On. See section "Forms Media (IDB Option 114)" on page 224. The command corresponds to event 62 - 63. Command - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 265
: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper Feed 265 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 267
" if it has been downloaded to the printer. It is also possible to select another font in the printer, e.g. a special mathematical font. The COD259 BEF command is executed each time there is a switch to code page 259 from another code page. It is not executed if code page 259 is selected repeatedly - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 268 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 269
immediately before the first printable character. See section "Overlay Call (IDB Option 28)" on page 177. OVLDRW command 1 is executed when paper tray 1 is selected and OVLDRW command 2 is executed when paper tray 2 is selected. The command corresponds to event 55 - 56. Command: OVLDRW - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 270 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 271
: POR LAN Before portrait selection Before landscape selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 271 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 272
is used as an extra headline when printing IDB and hex dumps The command is executed on the top of the first page. It may be used for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or company name. The command corresponds - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 273
is only sent if the print position is placed at line 1 and no characters have been printed. The contents of the string could be PCL codes like: • Top margin setting setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 274 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 275
3812-01 (5250 SCS) printer. One TN3270e connection is supported. Up to four TN5250e connections are supported. The SCS/TNe Emulation autodetects installed features to set initial settings for options such as duplex support (TN5250e only). Appendix - Specifications, Requirements, Features: Product - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 276 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 277
Print Platforms Mainframe Software • IBM Communications Server for OS/390 V2R5 or greater AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 278
: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 279
/DCA L2 data streams • 5 bin paper input and duplex • Computer Output Reduction (COR) / Automatic Page Orienta- tion (APO) • IBM font selection using FGID or CPI • IBM ASCII transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 280
Appendix B - ASCII Character Table Printable The table shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 282
TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 282 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 283
5 /... Enter Intermate transparent mode 5 = Reserved, active if option 31 = 0 5 +M Suppress format control codes 5 -M Standard handling of format control codes 5 {XY}.... Enter special transparent mode (X = option 171, Y = option 172) 3 {X}YYY[,ZZZ] - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 9) if necessary. Appendix - TN3270e IDB Commands: List of Commands 284 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 285
landscape based on menu option printed in landscape and compressed if the automatic page orientation (APO) and computer output reduction (COR) in the SCS/ TNe Emulation is switched on with the CORDRW command. The focus of this discussion is on how the printer automatic controls operate, as the user - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 286
are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information found in the FCB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 287
reduced from normal line spacing to a percentage value according to the LINSPRED option setting. Refer to section "COR LSI Reduc (IDB Option 127)" on page 205. • Margins (offset) are set according to the LFTOFFCOR and TOPOFFCOR option settings. Refer to section "Top Margin COR (IDB Opt. 80 & 81)" on - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 288
applications normally have a set of standard values for page length, characters per line etc. The user might have few or no possibilities off changing, the user to prevent a compressed landscape printout and force it into portrait with a font selected by them. Portrait can be forced with one of the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 289
file (CRTPRTF). Please consult your AS/400 or iSeries manuals for information on this subject. Defining the printer file to make the COR is normally done in connection with IPDS page printers as these printers do not support the APO/COR function. If the APO/COR is disabled (CORDRW 1/2 = OFF), the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 290 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 291 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 292
IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 292 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 293
format) Enter Intermate transparent mode Suppress format control codes Standard handling of format control Enter special transparent mode (X = Option 171, Y = Option 172) Double CSC (prints ) Single or Multibyte transparent character Print status dump Print font list Trig event no. X Refer to - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 294
IBM font IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR positions. When attempts to program more than 50 IBM fonts are made, it will print out a message and a font table status sheet. This status sheet has the IBM - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 295
into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID D10003, D10155, D10159, D10160, D10163 and D10175. The loading of these fonts can be disabled via the operator panel using the Download Font (IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 296
The "Font" Programming Command This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 298
The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM 154 - 200). The spacing command should only be used when using downloaded proportional fonts with the correct character spacing. N This value is - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 299
causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded proportional spaced - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 301
Set Substituted Font ID If a font ID sent from the system is not found in the font table, the font is substituted with a similar font defined in a special area of the font table. The first 7 font positions listed in the status printout (&%IDB_STATUS) represent the substitution fonts for the - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 302
ID 67, but all font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 302 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 303
User's Guide Second Edition October 2007, EC 20G429 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 304
Print Services Facility, PSF, System/390, zSeries, and z/OS are trademarks of International Business Machines Corporation in the United States, other countries, or both. Intelligent Printer Lexmark and Lexmark with diamond design, MarkNet and MarkVision are trademarks of Lexmark User's Guide ii - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 305
Requirements and Specifications ...2 Support ...4 Important Configuration Basics ...6 Introduction ...6 What are "IDB Options", "IDB events etc.? ...7 Setup Options vs. Printer Setup Options ...7 Understanding the Control Panel ...9 Introduction ...9 Printer operator panel ...10 MFP Touch Screen - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 306
for AS/400 and iSeries Users 53 Introduction ...53 Task 1 - Configuring the Host ...54 Task 2 - Configuring a Print Server ...56 Task 3 - Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 307
Reset ALL Def ...82 Operations Reference - TN3270E SETUP 83 Introduction ...83 NETWORK SETUP Menu: Options Overview ...87 Print Active ...88 TN3270 Defaults ...89 Connect Status ...90 NETWORK SETUP> SERVER INFO Menu: Options Overview 93 Name / IP Address ...94 IP Address ...95 Hostname ...96 TN - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 308
Size (IDB Option 90) ...143 Tray2 Paper Size (IDB Option 91) ...144 Tray3 Paper Size (IDB Option 92) ...145 Tray4 Paper Size (IDB Option 93) ...146 Tray5 Paper Size (IDB Option 94) ...147 TEST OPTIONS Menu: Options Overview ...148 SCS3270 Hex Dump ...149 Print 3270 IDB ...150 SCS3270 Defaults ...151 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 309
128) ...181 Move Hor/Ver (IDB Option 158) ...183 Format Ctrl Sup (IDB Option 177) ...185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu: Options Overview 190 IDB First Char (IDB Option 8) ...191 IDB Second Char (IDB Option 9) ...193 IDB - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 310
Lines Per Page (IDB Option 107) ...221 Top Margin (IDB Option 108) ...222 Source Input (IDB Option 113) ...223 Forms Media (IDB Option 114) ...224 Output Bin (IDB Option 115) ...225 Simplex/Duplex (IDB Option 116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 311
- Power On Initialize ...260 Paper Handling > Source Drawer ...262 Paper Handling > Destination Drawer ...263 Paper Handling > Select Paper / Envelope Media 264 Paper Handling > Select Paper Feed ...265 Paper Handling > Select Simplex/Duplex Printing 266 Code Page 259 > Before/After ...267 - Lexmark T644 | SCS/TNe Emulation User’s Guide - Page 312
Specifications, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280 Printable Characters ...280 Special TN3270e IDB Commands ...282 How to Print an IDB Report ...
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 275
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA