Lexmark X782 SCS/TNe Emulation User’s Guide
Lexmark X782 Manual
 |
View all Lexmark X782 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark X782 manual content summary:
- Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 1
see "Specifications, Requirements, Features" on page 275. SCS data is received in a LAN environment using the Telnet extended protocol. The Card for IPDS and SCS/TNe adds support for the TN3270E and the TN5250E protocols. A correctly configured printer can receive, process, and print SCS print jobs - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 2
in this manual refers to both printers and MFPs. Supported Products With the appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C770, C772, C780, C782, C920, C935 (IPDS color printing, SCS monochrome printing) • Lexmark T640, T642 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 3
called STD Net). • MarkNet internal print server (Ethernet). If you need to update your Standard Network or MarkNet firmware, refer to "Support" on page 4. For further information on requirements and specifications, see the appendix starting on page 275. Getting Started: Equipment Requirements and - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 5
This page is intentionally left blank Support: Customer Support 5 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 6
23 ff.) • Work with the settings remotely using IDB option strings (see "IDB Basics" on page 246 ff. and "Additional TN5250e Printer Commands Using IDB" on page 258 ff). Using IDB in this way is a highly technical process used only in connection with configurations and re-configurations. Detailed - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 7
" on page 246 for additional information. Note that in most cases, only technical specialists need to understand and use IDBs. Setup Options vs. Printer Setup Options Setup Options Changes to the option settings under the SCS/TNe MENU will only affect the printing of SCS jobs received through - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 8
> Utilities Menu > Restore Defaults does not affect the SCS/TNe MENU settings. Settings you choose in the SCS print job may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 9
as illustrating how how the control panel works. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs are illustrated here. "Installation Setup for Mainframe Users" on page 27 ff. and "Installation Setup for AS/400 and iSeries Users" on page 53 ff. Detailed, - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 10
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel scroll through lists of menu groups and options. As you move through the menus, the top line in the screen shows the menu or menu group name to which the displayed items belong. Understanding the Operator - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 11
as a Setting" on page 11 shows all details, while the following two sections discuss slight differences. User-selected default settings remain in a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator panel" on page 10. 2 Use the navigation buttons or to scroll to the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 12
the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP 9 TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK 9 SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 13
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS 9 MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup 9 Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 13 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 14
buttons to move down through the list. When the on-screen checkmark is next to the desired setting. press the Select button Country Code English (US) 9 Fin/Swe Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 15
saved, the display will revert to the previous menu level. MISC SETTINGS Format Ctrl Sup 9 Country Code Skip Blank Page If you want to check the value of a setting, press the Select button again. You times until the screen appears. Understanding the Operator Panel: Printer operator panel 15 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 16
the navigation buttons and to move between the characters. To store the new string, press Select after entering all the characters. Understanding the Operator Panel: Printer operator panel 16 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 17
to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 16. Understanding the Operator Panel: Printer operator panel 17 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 18
To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer is on and the Ready message appears. 2 Touch the key icon (Menus) on the through lists of menus and options. As you move through the menus, the top line in the screen shows the navigation path, so that you can always - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 19
to select and store new values are shown below. The section "Selecting a New Value as a Setting" on page 19 shows all details, while the following two sections discuss slight differences. User-selected default settings remain in effect until you save new settings or restore the factory defaults. All - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 20
touch MISC SETTINGS. 6 Now you will see a list of options.Touch or to scroll to the desired item. In this example locate and touch Country Code. 7 The currently active setting, in this example English (US), is always presented first. Touch or to scroll through the settings until you see the item - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 21
9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 22
example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 22 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 23
, the term printer in this manual refers to both printers and MFPs. The Card for IPDS and SCS/TNe includes an http user interface. You printers are attached to a LAN using a Standard Network port or MarkNet internal print server. Remote configuration is especially useful during printer installation - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 24
. How to Use the Browser Interface To access and change SCS/TNe option settings through your browser: 1 Access the printer web page by typing the IP address of its print server as the URL. 2 Select Configuration. 3 Select SCS/TNE Settings. 4 Select the TNe Common menu 5 Disconnect all sessions by - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 25
jobs are being received on this session. Wait for the jobs to finish printing or end the session from the host. If no jobs are printing, you may need to end and reset bottom of the page. The Submit button sends the new values to the printer. These values are saved in the printer and will become - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 26
configured sessions have not been established within 90 seconds, you may need to end and reset the sessions at the host and repeat steps 14 - 16. On each TN menu, you will see a Reset Form button at the bottom of the page, next to the Submit button. If you have entered values in the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 27
that you obtain the latest version of the MarkNet internal print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 28
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 28 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 29
is described in IBM's VTAM documentation. The Mainframe software must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. "Mainframe Software" on page 277 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 30
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE,IRETRY=YES,IDNUM=B0008, PASSLIM=7,PUTYPE=2,DISCNT=NO,VPACING=0 LCPG90 LU LOCADDR=2,MODETAB=MT3274P,USSTAB=USB3274B, DLOGMOD=T3274M2 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 31
Sample Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or terminal devices) for telnet sessions as follows: TCP VBUILD TYPE=APPL SC0TCP01APPL AUTH=NVPACE, EAS=1, PARSESS=NO, MODETAB=ISTINCLM, SESSLIM=YES - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 32
member (i.e. IMLU1 listed above) to the host print software being used. The following is an example of a TN printer definition defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 33
SCS) printer. Two sample configurations are shown below. Sample Configuration number 1 Remote Device - Line definition In VTAM NCP * LNACC=SDLC SDLC SWLINE GROUP G14SD4 GROUP LNCTL=SDLC,TYPE=NCP,OWNER=PCCU1, NRZI=NO,REPLYTO=2, DIAL=YES S14535 LINE ADDRESS=(2535,Half),SPEED=9600, TRANSFR=20, DUPLEX - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 34
LOACADDR=4,MODETAB=MTP3816, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 34 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 35
a Host For TN3270e Printing TIP: Refer to your system documentation for further details. Refer also to IBM books such as the IBM book OS/390 eNetwork Communications Server V2R5, TCP/IP Implementation Guide, Volume 1: Configuration and Routing (document no. SG24-5227-00). The printer with the SCS - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 36
ENDPRTGROUP IPGROUP SPECIP 157.184.116.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 37
group as shown above (PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 38
Task 2B Configuring an SNA Server For TN3270e Printing IMPORTANT: The TN3270e components have to be installed in order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways and routers. The procedure in this section shows - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 39
created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 40
on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Touch Reports. 3 Scroll until one or more of the following appears. If none of these appear, then you do not have a Standard Network or internal print server installed. a If Network Setup Page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 41
server to be used for SCS printing, for example Standard Network, Network 1, or Network 2. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. 2 Set the Network Job Timeout. This timeout is used by - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 42
is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 42 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 43
to properly format and print SCS jobs that do not contain formatting commands in the job. The following three settings are usually the most important, but there are many other possibilities. TIP: Refer to Operations Reference - TN3270E SETUP: SCS3270 Defaults, page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 44
Option Default Value Country Code (IDB Option 2) English (US) Recommended Value Comments Your preferred country 2 Scroll to the desired value. Touch SelectSubmit to save one of the factory defaults. 3 Exit the menu by pressing touching Home. C. To enable Euro support 1 Select Menus > Option - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 45
/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. SCS jobs are printed from a LAN connected Mainframe using TCP/ IP and the telnet extended - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 46
NETWORK SETUP> SERVER INFO Menu: Options Overview" on page 93. SERVER INFO Option Name / IP Address to specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. 0.0.0.0 The service. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 47
Please note! Some hosts and servers only recognize uppercase LU Names. Specific Check with your system administrator for the correct setting. The device None. 3 Set Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 48
> Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. Print Inactive to another status (there are examples of Connect Status messages on page 90. Mainframe users should continue with Task 6A. SNA Server users - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 49
the Mainframe Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 90) From the Operator Panel - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 50
not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. 3 From the main frame host give the following TCP/IP display command: D TCPIP - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 51
/SNA Server Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 90) From the Operator Panel - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 52
an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 53
obtain the latest version of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring the SCS Settings Task - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 54
Task 1 Configuring the Host The host operating system must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 277 lists host software which supports these protocols. To configure the host check and set the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 55
System Value QAUTOVRT Required Value Controls the automatic configuration of virtual devices. Must be set to an adequate number of devices Sample commands: DSPSYSVAL QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 56
on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Touch Reports. 3 Scroll until one or more of the following appears. If none of these appear, then you do not have a Standard Network or internal print server installed. c If Network Setup Page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 57
server to be used for SCS printing, for example Standard Network, Network 1, or Network 2. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. 2 Set the Network Job Timeout. This timeout is used by - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 58
or Off On, if you use a DHCP server. Off, if you set the IP address another way. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 58 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 59
setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 59 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 60
print SCS jobs which do not contain formatting commands in the job for your specific country 1 Select Menus > Option Code. Scroll to your preferred country and touch Submit. Option Country Code (IDB Option 2) Default Value International Recommended Value Comments Your preferred country code - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 61
code page 3 Still within MISC SETTINGS, locate Lines Per Page. Scroll to the desired Number and touch Submit to save it. Option Lines Per Page (IDB Option 107) Default Value 68 (for A4) Recommended Value Comments 64 (for Letter). 82 (for Legal). Recommended values for users in - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 62
to save it. Default Value 16848 (for A4) Recommended Value Comments 15840 (for Letter). Recommended values for users in 20160 (for Legal). the USA 7 Still within PAPER SETTINGS, locate Page Width. Scroll to the desired value and touch Submit to save it. Default Value 11908 (for A4) Recommended - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 63
1 Select Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 64
end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. SCS jobs are printed from a LAN connected AS/400 or iSeries host using TCP/IP and - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 65
# > SERVER # INFO Menu: Options Overview" on page 163. Option Default Value Name / IPaddress # Use IP to specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. The host's service. AS/400 and iSeries Installation Setup: Task 4 - Configuring - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 66
be auto configured. Contact your system administrator if you do not know the library name. Normal Leave this option at its default value to have printer intervention required conditions reported to the host. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 66 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 67
, it will begin session negotiation to restart the writer. The TN5250e emulation can only sense the writer has ended after the first SCS job has started to print. If the writer ends before sending an SCS job to the printer, the TN5250e emulation will not be able to sense the writer has ended. 6 Set - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 68
, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 90. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 68 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 69
the Host Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN5250E Connection Status (see page 160). From the Operator Panel - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 70
an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 71
/TNe Cancel About Cancel Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 72
on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only one Print Job shown, as in the example below - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 73 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 74
Job 1 While any job is printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected Job icon. 4 The screen will display a message to indicate that the job - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 75
and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN Session • SCS Debug Trace Operations - Common Setup: Introduction 75 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 76
access the Menu Settings Page • Reset ALL Def You will always be able to see the selected value for each option on the Menu Settings page. • From the Operator Panel: Select Menus > Reports > Menu Settings Page. • Through the http (browser) user interface: Connect to the print server by entering the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 77
name Values Disconnect Ses Do Not Disconn., Disconnect Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 78
the same action as if Back had been pressed in the operator panel. Disconnect Ses. Disconnect ALL active TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must be performed before the SCS/TNe Emulation will attempt to contact the host. Operations - Common Setup: Disconnect - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 79
Reset TN Session IMPORTANT: Powering the printer Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 78. This option - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 80
port to receive the trace data, the printer will remain Ready and may not complete printing performance, it should only be enabled when needed by service personnel for troubleshooting and service job is processed. This decreases trace performance significantly. It is recommended to set the Download - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 81
trace data output. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be added to provide additional ports for output of the debug trace data. Operations - Common Setup: SCS Debug - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 82
option settings to fac- tory defaults. Operator panel text Comments Do Not Reset Reset ALL Do not restore any settings. This performs the same action as if have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 83
- TN3270E SETUP Introduction This section describes the SCS/TNe Emulation TN3270E SETUP menu structure and options. Settings under this menu are used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 84
Time MISC SETTINGS FF Support Non-Print Char CSC Characters IDB Delimiter Use IR Format Ctrl Sup Country Code Skip Blank Page CPI Max Prt Pos LPI Line Spacing LPP Transparency Form Strings IBM Trn Code Leadin Sequence Euro Support PAPER SETTINGS Left Margin Right Margin Top Margin Bottom Margin - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 85
SCS OPTIONS menu for the option. Settings specified in an SCS job override the SCS/TNe Emulation default settings. An asterisk (*) next . The Menu Settings page shows the text string "[invalid]" for options set outside their ranges. Invalid will print for installed features which were selected as - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 246 ff.) Operations - TN3270E SETUP: Introduction 86 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 87
menu options found under the NETWORK SETUP menu. NETWORK SETUP Option name Print Active TN3270 Defaults Connect Status SERVER INFO Values No *, Yes Do (page 90) for a description of each message. Sub-menu. See NETWORK SETUP> SERVER INFO Menu: Options Overview (page 93) and Name / IP Address (page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 88
SCS/TNe Emulation for TN3270e communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 89
TN3270 Defaults This Network Setup option restores the TN3270e NETWORK SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 90
. The option cannot be changed by the user. Normally only the primary status is shown. If problems occur, a last response message is appended TN server Not Configured Print Inactive * Comments A Telnet connection is established and the SCS/TNe Emulation is ready to receive print jobs. The LU name - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 91
Rsp:No support for that device-type Lst Rsp:Name unknown to server Lst Rsp:The requested device is in use Lst Rsp:Terminal/Printer name been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 92
to some terminal The SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has occurred. Operations - TN3270E SETUP: NETWORK SETUP - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 93
up to 16 characters TN Server Port 23 *, range: 0 - 65000 LU Name [undefined] *, ASCII name with up to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 *, range: 1 - 32000 [seconds] A description of each SERVER INFO - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact the host or Telnet server. Option Value Use IP Address * Use Hostname Comments Use the IP address specified with the IP Address option. Use the hostname specified with the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 97
TN Server Port This Network Setup > Server Info option specifies the TCP Telnet server port defined on the host. Check with your system administrator for the correct Telnet server port to use. Option Value 23 * [0..65000] Comments This is the default port number for Telnet sessions according to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 98
Remember also to check the setting of the Device Type option. If a specific LU name is requested, then the name must be defined and available on the Connect Status option or on the Menu Settings page ( "How to access the Menu Settings Page" on page 76). Check with your system administrator for the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 99
* Associated Generic Comments Request a specific LU name. Make sure this has been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 100
Keep Alive Type IMPORTANT: If the Mainframe has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type of keep alive signal sent to the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive signal sent to the host or SNA gateway server. The Keep Alive Type setting specifies the type of signal sent to the host. Set this option to a value smaller than the session's - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 102
Sub-menu. See SCS Options > MISC SETTINGS Menu: Options Overview (page 104) and FF Support (IDB Option 5) (page 106). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 131) and Left Margin (IDB Option 103) (page 133). A description of each of the SCS OPTIONS menu item follows - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 103
. When APO is enabled the SCS/TNe Emulation calculates the print area required for printing the document. This is based on page formatting commands received from the host. If the document does not fit on a page in portrait orientation, the orientation is changed to landscape. Option Value - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 104
SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters ( IDB Options 8 & 9) IDB Delimiter (IDB Option 7) Use IR (IDB Option 21) Format Ctrl Sup (IDB Option 177) Country Code (IDB Option 2) Skip Blank Page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 105
Strings (IDB Option 168) IBM Trn Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range: 1 - > MISC SETTINGS > BOLD PRINT Menu - Options Overview (page 127) and Bold On CR (IDB Option 22 bit 1) (page 128). A description of each - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 106
when the MPL (Maximum Page Length) or BM (Bottom Margin) is reached in the data stream. Option Value Always FF * Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 106 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 107
Non-Print Char (IDB Option 3) This SCS Options > MISC Settings option defines the replacement character to substitute for an unprintable character found in the data stream. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of printable characters and their values. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 108
all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are ASCII characters in the decimal range 33 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. TIP: Several options are - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 109
programming commands. The IDB option value is an ASCII character in the decimal range 32 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon (:)] Advanced IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 110
) This SCS Options > MISC Settings option controls Intervention Required (IR) reporting to the host. If the option is enabled, IR signals are sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 111
print and Local Copy print. It can be enabled with the -M command. All host generated codes are still sent. Is diabled after Power On in Host direct print . Note: Because control codes are suppressed, horizontal/vertical tab and other commands which depend on correct page format will not work - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 112
still enabled. NOTE: = &% is factory default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 112 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 113
the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: After this command, all Host generated control codes are processed and the auto-NL function operates as normal. Refer to "Appendix C - Special TN3270e IDB Commands" on page 282 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 114
Country Code (IDB Option 2) This SCS Options > MISC Settings option defines the character set. Option Value Aus/Ger Aus/ , U.S. See note. Finnish/Swedish Finnish/Swedish Alternate French/Azerty 105 International Italian Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 114 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 115
changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:1:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 115 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 116
(IDB Option 32) This SCS Options > MISC Settings option controls whether or not blank pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 117
CPI (IDB Option This SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 118
Max Prt Pos (IDB This SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 119 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 120 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 121
LPP (IDB Option 107) This SCS Options > MISC Settings option defines the number of lines per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 122
Transparency This SCS Options > MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 123
String Utility. The lead in character is an ASCII character in the decimal range 0 255. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of printable characters and their values. Option Value ASCII Value 0 * ASCII Value [1..255] IDB Value 0 1 - 255 Comments Disable - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 124
from EBCDIC to ASCII. Data outside the range 40H - FEH is printed as a hyphen. See the Non-Print Char (IDB Option 3) option. 1 Data within a transparent data stream (LU-1 (SCS) control code 35H) is printed as received. No translation from EBCDIC to ASCII is performed. All transparent - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 125
option defines the kind of lead in sequence used. Option Value Normal * Without '&%' IDB bit option value Comments 0 Normal user defined trans- parent handling. 1 User defined transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 126
This SCS Options > MISC Settings option controls Euro character (IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 127
is a sub-menu under the MISC SETTINGS menu. The following table lists menu options found under the BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS (IDB Option 22 bit 2) Bold On Multi BS (IDB Opt. 22 bit 3) Values - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 128
Bold On CR (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 129
Bold On BS (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 130
Bold On Multi BS (IDB Opt. 22 bit 3) This SCS Options > MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 131
. The following table lists menu options found under the PAPER SETTINGS menu. Option name Left Margin (IDB Option 103) Right Margin (IDB Option 104) Top Margin (IDB Option 108) Bottom Margin (IDB Option 109) Source Input (IDB Option 113) Tray 1 Orient (IDB Option 123) Tray 2 Orient (IDB Option 124 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 132 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 133
Left Margin (IDB Option 103) This SCS Options > Paper Settings option defines the left margin position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 134
Right Margin (IDB Option 104) This SCS Options > Paper Settings option defines the right margin position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &% - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 135
Margin (IDB Option 108) This SCS Options > Paper Settings option defines line number position of the top margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 136
Bottom Margin (IDB Option 109) This SCS Options > Paper Settings option defines the line number position of the bottom margin. The line height depends on the setting of the LPI (IDB Option 105) option. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 137
IDB Option 113) source. Option Value Prtr Setting Tray 1 * Tray 2 Tray 3 Tray 4 Tray 5 IDB Value 0 1 2 3 4 5 Comments Feed paper from the paper source selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 138
Tray 1 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 139
Tray 2 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 140
Tray 3 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 141
Tray 4 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 142
Tray 5 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 143
Input (IDB Option 113) Tray 1 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 144
Input (IDB Option 113) Tray 2 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 145
Input (IDB Option 113) Tray 3 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 146
Input (IDB Option 113) Tray 4 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 147
Input (IDB Option 113) Tray 5 is selected and the APO/COR function has been activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 148
. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print SCS3270 Defaults Do Not Restore *, US-Default, Non-US-Default A description of each TEST OPTIONS menu item follows - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 149
SCS3270 Hex Dump This Test option enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 150
IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. Advanced IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 151
factory default settings. Other printer emulation defaults are unchanged. The restored settings become active on the next SCS job. Option Value Do between the US and the Non-US factory default settings. Affected option Country Code (IDB Option 2) Bottom Margin (IDB Option 109) LPP (IDB Option 107 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 152
Tray2 Paper Size (IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 153
- TN5250E SETUP Introduction This section describes the SCS/TNe Emulation TN5250E SETUP menu structure and options. Settings under this menu are used when printing from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 154
Lef Margin COR Top Margin COR Lef Margin Lan Top Margin Lan Page Length Page Width Country Code Codepage Font CPI Max Print Pos Left Margin Right Margin LPI Lines Per Page Top Margin Source Input Forms Media Output Bin Simplex/Duplex Non-Print Char Def Page Ori 1 Def Page Ori 2 COR Action - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 155
SCS OPTIONS menu for the option. Settings specified in an SCS job override the SCS/TNe Emulation default settings. An asterisk (*) next . The Menu Settings page shows the text string "[invalid]" for options set outside their ranges. Invalid will print for installed features which were selected as - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 156
by remote configuration. Following this are two command lines, one for the User IDB language and another for the Advanced IDB language. These show how "IDB Basics" on page 246 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 258 ff.) Operations - TN5250E SETUP: Introduction - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 157
The SCS/TNe Emulation supports four concurrent TN5250E sessions. the way all TN5250E jobs are printed. The following table lists menu options found under the CONNECTION Messages and Last Response Messages. Refer to Connect # Status (page 160) for a description of each message. SERVER # INFO Sub - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 158
SCS/TNe Emulation for TN5250E communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 159
TN5250## This Connection# option restores the TN5250E CONNECTION #1, Default #2, #3, or #4 factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 160
with the host. The option cannot be changed by the user. The first part of the line shows the primary status message of the 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports > print server to be used for SCS printing > NPA Mode). 3 Cable is not plugged into print server. Plug - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 161
. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session established on system [SYSTEM NAME] A Telnet connection is established and the SCS/TNe Emulation is ready to receive print jobs. The [SYSTEM - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 162
not valid Lst Rsp:8916:No matching device found Lst Rsp:8917:Not authorized to object Lst Rsp:8918:Job canceled Lst Rsp:8920:Object partially damaged Lst Rsp:8921:Communication error Lst Rsp:8922:Negative response received Lst Rsp:8923:Start-up record incorrectly Lst Rsp:8925:Creation of device - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 163
Connect # Status: Last response messages Lst Rsp:8935:Session rejected Lst Rsp:8936:Security failure on session Lst Rsp:8937:Automatic sign-on rejected Lst Rsp:8940:Automatic config. failed Lst Rsp:I904:Source at incompatible release Comments Check with system operator. Check with system operator. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 164
Connection# > SERVER # INFO Option name Values Keep Alive Time 45 *, range: 1 - 32000 [seconds] MSGQ # Name QSYSOPR *, ASCII name with up to 10 characters. MSGQ # Lib *LIBL *, ASCII name with up to 10 characters. IR # Reply Normal *, Offline, No Reply Auto Sense # END No *, Yes A - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 165
IP # Address This Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 166
Hostname # This Connection# > Server# Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 167
Server # TN Port This Connection# > Server# Info option specifies the TCP Telnet server port defined on the host. Check with your system administrator for the correct Telnet server port to use. Option Value 23 * [0..65000] Comments This is the default port number for Telnet sessions according to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 168
Device # Name This Connection# > Server# Info option specifies the device and writer name associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 169
Keep Alive Type IMPORTANT: If the host has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Connection# > Server# Info option specifies the type of keep alive signal sent to the host. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 170
Keep Alive Time TIP: Set this option to as big a value as possible. Be sure it is smaller than the session's inactivity timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires between each keep - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 171
MSGQ # Name This Connection# > Server# Info option specifies the message queue name on the host to which Intervention Required conditions are reported. The message queue name must already exist on the host. It will not be auto created. The MSGQ # Lib option may be used to set the message queue - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 172
MSGQ # Lib This Connection# > Server# Info option specifies the message queue library for the message queue specified in the MSGQ # Name option. The message queue library must already exist on the host. It will not be auto created. Leave this option at the default if you do not know the library - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 173
IR # Reply This Connection# > Server# Info option controls the reporting of Intervention Required Replies to the host. Option Value Normal * Offline No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 174
SCS/TNe Emulation senses automatically if the host has ended the Writer. This may be necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer ends, reconnect, and - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 175
Hor/Ver (IDB Option 158) Use Escape *, Use Line feed, Space + Escape, Linefeed + Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 175 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 176
-menu. See SCS OPTIONS > COR/APO SETTINGS Menu: Options Overview (page 196) and Def Page Ori 1 (IDB Option 121) (page 197). Sub-menu. See SCS OPTIONS > MISC SETTINGS Menu: Options Overview (page 206) and Country Code (IDB Option 2) (page 208). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 177
Overlay Call (IDB Option 28) This SCS Options option defines if an overlay call (predefined string) is printed on the top of each page. The overlay may contain a call to an electronic form, a macro, or the string stated by the OVLDRW command itself. It has a maximum of 255 characters. A - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 178 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 179
proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which . Option Value Do Not Use * Use IDB Value 0 1 User IDB parameter OFF ON User IDB command: PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 180 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 181
to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 10 CPI, 96 C-----P----I---×-----5---0-49 Option Value Off * On IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI ( - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 182 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 183
HORMOV / VERMOV : Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 184 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 185
enabling and disabling the "Auto newline" feature of the SCS/TNe Emulation. If the printout is incorrectly double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 186
that these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 187 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 188
Support (IDB Option 139) This SCS Options option controls Euro character printing. If the option is set to Yes, the normal code pages are re-mapped to code pages containing the Euro character. This means that the international currency symbol is replaced with the Euro character in the EBCDIC code - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 189
be able to print the Euro character a font supporting the character also has to be selected and available in the printer. See the Download Font (IDB Option 244) option on page 186 and the Font (IDB Options 242 and 243) option on page 213. Option Value No * Yes IDB Value 0 1 User IDB parameter OFF - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 190
SCS OPTIONS > CSC CHARACTERS Menu: Options Overview The CSC CHARACTERS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the CSC CHARACTERS menu. SCS OPTIONS > CSC Characters Option name IDB First Char (IDB Option 8) IDB Second Char (IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 191
printer, e.g. &%1B = . The IDB option value is an ASCII character in the decimal range 33 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. Option Value & * IDB Value 38 [ampersand] User IDB command: Not supported Parameter - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 192 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 193
the printer, e.g. &%1B = . The IDB option value is an ASCII character in the decimal range 33 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. Option Value % * IDB Value 37 [percent] User IDB command: Not supported Parameter - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 194 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 195
33 - 126. Refer to "Appendix B - ASCII Character Table" on page 280 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 196
menu options found under the COR/APO SETTINGS menu. SCS Options > COR/APO Settings Option name Values Def Page Ori 1 (IDB Option 121) Portrait *, Prtr Setting, Landscape Def Page Ori 2 (IDB Option 122) Portrait *, Prtr Setting, Landscape COR Action 1 (IDB Option 123) Enable Auto COR *, Disable - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 197
used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 1 (IDB Option 123) option. Option Value Prtr Setting Portrait * Landscape IDB Value 0 1 2 User IDB parameter DEF POR LAN User IDB command: ORTDRW 1 : Parameter: DEF - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 198
used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 2 (IDB Option 124) option. Option Value Prtr Setting Portrait * Landscape IDB Value 0 1 2 User IDB parameter DEF POR LAN User IDB command: ORTDRW 2 : Parameter: DEF - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 199
disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between page 285. When Enable APO is selected, the SCS/TNe Emulation calculates the print area required for printing the document. If the document does not fit on the page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 200
. Option Value IDB Value Disable 0 Enable APO 1 Enable Auto COR * 2 Disable STO 3 User IDB parameter OFF APO COR STODIS User IDB command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 201
disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between page 285. When Enable APO is selected, the SCS/TNe Emulation calculates the print area required for printing the document. If the document does not fit on the page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 202
. Option Value IDB Value Disable 0 Enable APO 1 Enable Auto COR * 2 Disable STO 3 User IDB parameter OFF APO COR STODIS User IDB command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 203
is used to disable text mode. When text mode is disabled, the APO/COR function will ignore the print quality parameter and print all print jobs fulfilling the requirements in computer output reduction mode. Refer to "Appendix D - COR/APO Logic (TN5250e)" on page 285 Operations - TN5250E SETUP: SCS - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 204
OFF Normal IBM interpretation ON Ignore the system TEXT parameter APO Observe TEXT parameter in APO as well User IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 205
/APO Settings option defines the line spacing in Computer Output Reduction mode. The spacing is normally set to 70% of the normal line spacing (100%). Option Value 70% * [1..100] IDB Value 70 User IDB parameter 70 User IDB command: LINSPRED : Parameter: 1 - 100 percent of normal line - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 206
name Country Code (IDB Option 2) Codepage (IDB Options 240 and 241) Font (IDB Options 242 and 243) CPI (IDB Option 100) Max Print Pos ( 290, 751, 1051, 1053, 1056, 1351, 1653, 2103 10 CPI *, 5 CPI, 12 CPI, 15 CPI, 16.7 CPI 80 *, range: 1 - 254 1 *, range: 1 - 255 1 *, range: 1 - 255 6 LPI *, 3 LPI, - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 207
SCS OPTIONS>MISC SETTINGS Option name Lines Per Page (IDB Option 107) Top Margin (IDB Option 108) Source Input (IDB Option 113) Forms Media (IDB Option 114) Output Bin (IDB Option 115) Simplex/Duplex (IDB Option 116) Non-Print Char (IDB Option 3) Values 68 *, range: 1 - 255 1 *, range: 1 - 255 Tray - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 208
all country codes. In country codes other than International country specific characters replace selected characters. Option Value International * USA/Can Ger/Aus Belgium Brazil Can/Fre Den/Nor Fin/Swe France Italy Jap (Latin) USA/Can bil. Portugal IDB Value 0 1 2 3 4 5 6 7 8 9 10 11 12 User IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 209
13 14 15 User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 210
241) This SCS Options > Misc Settings option defines the code page to be used. Country definition by "Code Page" is commonly used by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 273, 277, 278, 280, 284, 285, 297, 500 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 211
Option Value IDB Values (Option 240 and 241) User IDB parameter OCR 340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this line Turkey 1023 255 + 3 1023 USA/Can 1140 116 + 4 1140 Ger/Aus 1141 117 + 4 1141 Den/Nor 1142 118 + 4 1142 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 212 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 213
system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option Value ( 12 110 Let.Got. Bld 12 111 Pres. Bold 12 112 Pres. It 12 IDB Value (Option 242 and 243) User IDB parameter 3 + 0 3 11 + 0 11 18 + 0 18 39 + 0 39 40 + 0 40 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 214
Got.Text 20 290 Got.Text 27 751 Son.Ser. 7 1051 Son.Ser. 10 1053 Son.Ser.Bld 10 IDB Value (Option 242 and 243) User IDB parameter 155 + 0 155 159 + 0 159 160 + 0 160 163 + 0 163 175 + 0 175 204 + 0 204 221 + 0 221 222 + 0 222 223 + 0 223 230 + 0 230 244 + 0 244 245 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 215
.Ser.Bld 16 2103 Son.Ser.Bld 24 IDB Value (Option 242 and 243) User IDB parameter 32 + 4 1056 71 + 5 1351 117 + 6 1653 35 + 8 2103 User IDB command: DEFFNT : Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 216
inch). Option Value 5 CPI 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 5 10 12 15 16 User IDB parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 217
defines the maximum (IDB Option 102) horizontal print position. Option Value 80 * [1..254] IDB Value 80 User IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 218
depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 219
depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 220
of 105) lines per inch (LPI). Option Value 3 LPI 4 LPI 6 LPI * 8 LPI 9 LPI IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT: DEFLPI 6:EXIT Advanced IDB language to set factory - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 221
Options > Misc Settings option defines the number of (IDB Option 107) lines per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT Advanced IDB language - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 222
> Misc Settings option defines the top margin in lines. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 223
contain a string which selects a specific tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 224
Select Media (SLTMED) command. Option Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory default: &%IDB_EDIT: DEFFRMSEL DEF:EXIT Advanced IDB language to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 225
(DSTDRW) command. Option Value Prtr Setting * Output Bin 1 Output Bin 2 Output Bin 3 IDB Value 0 1 2 3 User IDB parameter DEF 1 2 3 User IDB command: DEFDSTDRW : Parameter: DEF, 1, 2, 3 User IDB language to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 226
Select Simplex/Duplex Printing (SLTSIMDUP) command. The tumble setting is used for pages connected or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 227 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 228
option defines the replacement character to substitute for an unprintable character found in the data stream. The character is printed when the host sends an unprintable character or a character not supported by the SCS/TNe Emulation. Refer to "Appendix B - ASCII Character Table" on page 280 for - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 229
Options > Paper Settings Option name Left Margin COR (IDB Opt. 78 & 79) Top Margin COR (IDB Opt. 80 & 81) Left Margin Lan (IDB Opt. 86 & 87) Top Margin Lan (IDB Opt. 88 & 89) Page Length (IDB Opt. 82 & 83) Page Width (IDB Opt.84 & 85) Values 634 *, range: 0 - 2880 0 *, range: 0 - 2880 0 *, range - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 230
the offset to be added to the left margin when printing in Computer Output Reduction mode (COR). COR is a feature that allows data processing reports to fit on A4 [0.00 .. 2.009 or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 231
The option values for option 78 and 79 are calculated using the formulas below. 79: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 78: (Marg. inch × 1440) - (256 × Value stored in option 79) Round off to nearest whole number. The values stored in - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 232
the offset to be added to the top margin when printing in Computer Output Reduction mode (COR). COR is a feature that allows data processing reports to fit on A4 size paper. 1 inch = 1440. Option Value (1/1440 inch) IDB Values (Option 80 and 81) User IDB parameter 0 * [0..2880] 0 + 0 0.00 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 233
in option 81) Round off to nearest whole number. The values stored in option 80 and 81 for a top margin offset of 1 inch are calculated like this: 81: 1-----×-----1---4----4---0-256 ≈5 80: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 234
printing in Landscape mode. 1 inch = 1440. Option Value (1/1440 inch) IDB Values (Option 86 and 87) User IDB parameter 0 * [0..2880] 0 + 0 0 User [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 235
The option values for option 86 and 87 are calculated using the formulas below. 87: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 86: (Marg. inch × 1440) - (256 × Value stored in option 87) Round off to nearest whole number. The values stored in - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 236
option defines the offset to be added to the top margin when printing in Landscape mode. 1 inch = 1440. Option Value (1/1440 inch) IDB Values (Option 88 and 89) User IDB parameter 147 * [0..2880] 147 + 0 0.10 User IDB command: TOPOFFLAN : Parameter 1: I for inches - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 237
- (256 × Value stored in option 89) Round off to nearest whole number. The values stored in option 88 and 89 for a top margin offset in Landscape of 0.102 inch are calculated like this: 89: 0----.-1----0---2-----×-----1---4---4----0-256 ≈0 88: (0.102 × 1440) - (256 × 0) ≈ 147 NOTE: Inches can - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 238
& 83) This SCS options > Paper Settings option defines the page length used by the APO/COR (Automatic Page Orientation function/Computer Output Reduction) to calculate page orientation. Option Value (1/1440 inch) IDB Values (Option 82 and 83) User IDB parameter 16848 * [1..65535] 208 + 65 11.70 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 239
or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG Round off to nearest whole number. The values stored in option 82 and 83 for a page length of 11.70 inch are found like this: 83: 1----1---.--7---0-----×-----1---4---4----0-256 ≈ 65 82: - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 240
This SCS options > Paper Settings option defines the page width used by the APO/COR (Automatic Page Orientation function/Computer Output Reduction) to calculate page orientation. Option Value (1/1440 inch) IDB Values (Option 84 and 85) User IDB parameter 11908 * [1..65535] 132 + 46 8.27 Values - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 241
or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I Round off to nearest whole number. The values stored in option 84 and 85 for a page width of 8.27 inch are found like this: 85: 8----.-2----7-----×----1----4---4---0-256 ≈ 46 84: (8. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 242
table lists menu options found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print SCS5250 Defaults Do Not Restore *, Restore Defaults A description of each TEST OPTIONS menu option follows. Operations - TN5250E - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 243
SCS5250 Hex Dump This Test option enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 244
report when asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. User IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN5250E - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 245
SCS5250 This Test option restores the TN5250E SCS OPTIONS settings to Defaults their factory default values. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 246
SCS/TNe Emulation's storage of all SCS protocol conversion tables. This chapter reviews how to use IDB commands to change the SCS option settings remotely. guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 247
is somewhat easier to use. However, the User IDB Language is only available for working on approximately control settings on a job by job basis. An IDB language is used directly from the AS/400, iSeries or Mainframe host by printing IDB command line sequences on the printer. This is typically done - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 248
9 ff. "Operations Reference - TN3270E SETUP" on page 83 and "Operations Reference - TN5250E SETUP" on page 153. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 258 covers IDB commands which can be embedded in - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 249
3 All option settings with syntax or range errors are ignored. If the SCS/TNe Emulation prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory defaults. IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 250
common to the two languages. Enter configuration mode by sending the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings are active on the next SCS job. All configuration options must be separated - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 251
Programming examples Advanced IDB (TN3270E + TN5250E) User IDB (TN5250E) Valid &%IDB_EDIT: &%IDB_EDIT: TN3270E SETUP" on page 83 and in chapter "Operations Reference - TN5250E SETUP" on page 153. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 258 covers IDB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 252
on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups. IDB Basics: IDB Configuration File Management 252 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 253
" directory. cd /lti 3 Set the FTP client to binary mode. This is necessary as data is transferred in binary mode. binary 4 Retrieve the IDB configuration file. get tn3270e.idb c:\tn3270e.idb (TN3270E users) get tn5250e.idb c:\tn5250e.idb (TN5250E users) This stores the file on the PC in the root - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 254 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 255
DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File TN3270E P01 options and events not described in this guide. Only options and events described in this guide should be configured.The IDB configuration file - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 256
has been edited it can be downloaded to the SCS/TNe Emulation. The download file name is fixed. Downloading a file with a different name address) User name: 2 Enter the "/lti" directory. cd /lti 3 Set the FTP client to binary mode. This is necessary as data is transferred in binary mode. - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 257 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 258
recognized, i.e. included in the SCS data stream. The commands you may work with fall into three groups: 1 Paper Handling 2 Code Page Handling / Code Page 259 3 Miscellaneous See "IDB Basics" on page 246 ff. for background information on IDB. TN5250e Printer Commands Using IDB: Introduction 258 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 259
Input Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 260
of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected. 3 DEFCPI (CPI) (option 100) triggers - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 261
initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 261 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 262
74 - 78 require programming before they can be used to select a specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command Parameter - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 263
by the DEFDSTDRW command at Power On. See section "Output Bin (IDB Option 115)" on page 225. The command corresponds to event 59 - 61. Command: DSTDRW : 2 to bin 1 Delete command string for dest.drawer 1 TN5250e Printer Commands Using IDB: Paper Handling > Destination Drawer 263 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 264
This is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when printing on paper or envelopes is selected. It can also be triggered by the DEFFRMSEL command at Power On. See section "Forms Media (IDB Option 114)" on page 224. The command corresponds to event 62 - 63. Command - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 265
Feed This is triggered by the AS/400 or iSeries command SPSU (Set Print Setup) when a certain kind of paper feed is selected. The command paper feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 266
Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. It - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 267
it has been downloaded to the printer. It is also possible to select another font in the printer, e.g. a special mathematical font. The COD259 BEF command is executed each time there is a switch to code page 259 from another code page. It is not executed if code page 259 is selected repeatedly. The - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 268 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 269
or 2 is executed at the top of each page immediately before the first printable character. See section "Overlay Call (IDB Option 28)" on page 177. OVLDRW command 1 is ,"&f2X":PCL string for calling macro no. 3 OVLDRW DEL 1: TN5250e Printer Commands Using IDB: Miscellaneous > Overlay Command 269 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 270 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 271
: POR LAN Before portrait selection Before landscape selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 271 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 272
is used as an extra headline when printing IDB and hex dumps The command is executed on the top of the first page. It may be used for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or company name. The command corresponds - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 273
top margin. The string is only sent if the print position is placed at line 1 and no characters have been printed. The contents of the string could be PCL codes like: • Top PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 274 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 275
printer capable of printing SCS documents received over a LAN connection. With the appropriate AS/400, iSeries, or Mainframe host software and this option, the printer can emulate an IBM 3287/3812 in LU1 mode (3270 SCS) or an IBM 3812-01 (5250 SCS) printer. One TN3270e connection is supported - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 276 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 277
Server for VTAM V4R4 or greater AS/400 and iSeries Software • Application System AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms 277 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 278
Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features: Features - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 279
code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC character conversion • SCS command conversion • Text string conversion • IBM and 3rd party ASCII transparent modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features: Features - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 280
shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 R 82 6A j 106 23 # 35 3B ; 59 53 S 83 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 282
TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 282 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 283
5 = Reserved, active if option 31 = 0 5 +M Suppress format control codes 5 -M Standard handling of format control codes 5 {XY}.... Enter special transparent mode (X = option 171, Y = option 172) 3 {X}YYY[,ZZZ] Formatted string (X = Option 168, YYY = String - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 9) if necessary. Appendix - TN3270e IDB Commands: List of Commands 284 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 285
dump is usually printed in landscape and compressed if the automatic page orientation (APO) and computer output reduction (COR) in the SCS/ TNe Emulation is switched on with the CORDRW command. The focus of this discussion is on how the printer automatic controls operate, as the user does not always - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 286
are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information found in the FCB - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 287
to the LINSPRED option setting. Refer to section "COR LSI Reduc (IDB Option 127)" on page 205. • Margins (offset) are set according to the LFTOFFCOR and TOPOFFCOR option settings. Refer to section "Top Margin COR (IDB Opt. 80 & 81)" on page 232 and to section "Left Margin COR (IDB Opt. 78 & 79)" on - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 288
• Other pitch sizes are compressed to the nearest smaller font. 4 Most program applications normally have a set of standard values for page length, characters per line etc. The user might have few or no possibilities off changing, e.g., the number of characters per line, which is normally set to 132 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 289
is normally done in connection with IPDS page printers as these printers do not support the APO/COR function. If the APO/COR is disabled (CORDRW 1/2 = OFF), the STO command will control the rotation of the printout. This means that if a landscape print job controlled by the STO command is received - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 290 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 291 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 292
IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 292 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 293
control codes Standard handling of format control Enter special transparent mode (X = Option 171, Y = Option 172) Double CSC (prints ) Single or Multibyte transparent character Print status dump Print font list Trig event no. X Refer to the chapter on Understanding the Control Panel (page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 294
IBM font IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR positions. When attempts to program more than 50 IBM fonts are made, it will print out a message and a font table status sheet. This status sheet has the IBM - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 295
), 159 (Boldface), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID D10003, D10155, D10159, D10160, D10163 and D10175. The loading - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 296
The "Font" Programming Command This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 298
The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM 154 - 200). The spacing command should only be used when using downloaded proportional fonts with the correct character spacing. N This value is - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 299
causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded proportional spaced - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 301
Set Substituted Font ID If a font ID sent from the system is not found in the font table, the font is substituted with a similar font defined in a special area of the font table. The first 7 font positions listed in the status printout (&%IDB_STATUS) represent the substitution fonts for the - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 302
to this command. The entire font definition (incl. string before/after etc.) is transferred to font table position 3. For instance, if IBM font 67 was the font SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 303
User's Guide Second Edition October 2007, EC 20G429 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 304
OS/400, Print Services Facility, PSF, System/390, zSeries, and z/OS are trademarks of International Business Machines Corporation in the United States, other countries, or both. Intelligent Printer Data Stream and property of their respective owners. Trademarks: SCS/TNe Emulation User's Guide ii - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 305
Started ...1 Documentation Overview ...1 Equipment Requirements and Specifications ...2 Support ...4 Important Configuration Basics ...6 Introduction ...6 What are "IDB Options", "IDB events etc.? ...7 Setup Options vs. Printer Setup Options ...7 Understanding the Control Panel ...9 Introduction - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 306
iSeries Users 53 Introduction ...53 Task 1 - Configuring the Host ...54 Task 2 - Configuring a Print Server Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 307
Overview 104 FF Support (IDB Option 5) ...106 Non-Print Char (IDB Option 3) ...107 CSC Characters (IDB Options 8 & 9) ...108 IDB Delimiter (IDB Option 7) ...109 Use IR (IDB Option 21) ...110 Format Ctrl Sup (IDB Option 177) ...111 Country Code (IDB Option 2) ...114 Skip Blank Page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 308
(IDB Option 167) ...122 Form Strings (IDB Option 168) ...123 IBM Trn Code (IDB Option 169 bit 1) ...124 Leadin Sequence (IDB Option 169 bit2) ...125 Euro Support (IDB Event 191) ...126 SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview 127 Bold On CR (IDB Option 22 bit 1) ...128 - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 309
SETUP 153 Introduction ...153 CONNECTION # Menu: Options Overview ...157 Print # Active ...158 TN5250## Default ...159 Connect # Status ...160 ) ...183 Format Ctrl Sup (IDB Option 177) ...185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 310
/Duplex (IDB Option 116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 229 Left Margin COR (IDB Opt. 78 & 79) ...230 Top Margin COR (IDB Opt. 80 & 81) ...232 Left Margin Lan (IDB Opt. 86 & 87) ...234 Top Margin Lan (IDB Opt. 88 & 89) ...236 Page - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 311
File ...255 Storing the IDB Configuration File ...256 Additional TN5250e Printer Commands Using IDB 258 Introduction ...258 Input Data String Syntax > Select Paper Feed ...265 Paper Handling > Select Simplex/Duplex Printing 266 Code Page 259 > Before/After ...267 Miscellaneous > Overlay Command ... - Lexmark X782 | SCS/TNe Emulation User’s Guide - Page 312
Specifications, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280 Printable Characters ...280 Special TN3270e IDB Commands ...282 How to Print an IDB Report ...
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 275
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA