LiftMaster 8360W 8360W Installation Manual
LiftMaster 8360W Manual
 |
View all LiftMaster 8360W manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster 8360W manual content summary:
- LiftMaster 8360W | 8360W Installation Manual - Page 1
Chain Drive Model 8360W FOR RESIDENTIAL USE ONLY • Please read this manual and the safety MyQ® and Security+ 2.0® accessories. • DO NOT install on a one-piece door if using devices or door opener to receive updates and offers from LiftMaster Take a photo of the camera icon including the points ( - LiftMaster 8360W | 8360W Installation Manual - Page 2
Contents Preparation 3 Assembly 7 Installation 9 Install the Door Control 17 Install the Protector System 19 Power 23 Adjustments 25 Battery Backup 28 Operation 30 Maintenance 37 Troubleshooting 38 Accessories 40 Warranty 41 Repair Parts 42 2 - LiftMaster 8360W | 8360W Installation Manual - Page 3
Serial Number Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these Safety Symbols - LiftMaster 8360W | 8360W Installation Manual - Page 4
router specifications and help, visit WiFiHelp.LiftMaster.com. See page 32 to connect the door. If balanced, it should stay in place, supported entirely by its springs. 3. Raise and lower the system may not work properly. 5. The opener should be installed above the center of the door. If there is - LiftMaster 8360W | 8360W Installation Manual - Page 5
Preparation Tools Needed 5/32 3/16 5/16 7/16 1/2 5/8 1/4 7/16 9/16 5 - LiftMaster 8360W | 8360W Installation Manual - Page 6
instructions for these accessories will be attached to the accessory and are not included in this manual. The images throughout this manual are for reference and your product may look different. Installation and literature P. Rail grease Q. 3-Button Remote Control (893LM) Door Control Hardware - LiftMaster 8360W | 8360W Installation Manual - Page 7
from the rail, chain, and styrofoam. 3. Fasten the rail with the previously removed bolts. 4. Position the chain around the garage door opener sprocket. 5. Install the sprocket cover by squeezing the sides and inserting the tabs into the slots on the garage door opener. HARDWARE Washered Bolt 5/16 - LiftMaster 8360W | 8360W Installation Manual - Page 8
Assembly 2 Tighten the Chain 1. Loosen the inner nut and lock washer on the trolley threaded shaft. 2. Tighten the outer nut until the chain is a 1/2 inch above the base of the rail at the midpoint of the rail. 3. Re-tighten the inner nut. Slack in the chain is normal when the door is closed. No - LiftMaster 8360W | 8360W Installation Manual - Page 9
instructed to do so. 8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms. 9. Install Place manual release/safety reverse test label in plain view on inside of garage door. 12. Upon completion of installation, - LiftMaster 8360W | 8360W Installation Manual - Page 10
To prevent possible SERIOUS INJURY or DEATH: l Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might NOT reverse when required. DO NOT install header bracket over drywall. l Concrete anchors MUST be used if mounting header bracket or 2x4 - LiftMaster 8360W | 8360W Installation Manual - Page 11
the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry fasten bracket securely to a structural support with lag screws. Lag Screw 5/16"-9 x 1-5/8" OPTION A WALL INSTALLATION 1. Center the bracket on the - LiftMaster 8360W | 8360W Installation Manual - Page 12
Installation 3 Attach the Rail to the Header Bracket 1. Align the rail with the header bracket. Insert the clevis pin and outer trolley. Slide the outer trolley toward the garage door opener. The trolley can remain disconnected until instructed. Clevis Pin 5/16" x 2-3/4" Connected Disconnected 12 - LiftMaster 8360W | 8360W Installation Manual - Page 13
, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing ANY brackets into masonry. Hanging your the bracket is not centered above the door). 7. Remove the 2x4. Operate the door manually. If the door hits the rail, raise the header bracket. NOTE: DO NOT - LiftMaster 8360W | 8360W Installation Manual - Page 14
Installation 6 Install the Light Bulbs 7 Attach the Emergency Release Rope and Handle To prevent possible OVERHEATING of the end panel or light socket: l Use ONLY A19 incandescent ( - LiftMaster 8360W | 8360W Installation Manual - Page 15
long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit. NOTE: Many door reinforcement kits provide for - LiftMaster 8360W | 8360W Installation Manual - Page 16
Installation 9 Connect the Door Arm to the Trolley IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close the - LiftMaster 8360W | 8360W Installation Manual - Page 17
. l NEVER permit children to operate or play with door control push buttons or remote control transmitters. l Activate door ONLY when it can be Security+ 2.0® door controls. NOTE: Older LiftMaster door controls and third party products are not compatible. Install the door control within sight of the - LiftMaster 8360W | 8360W Installation Manual - Page 18
and ceiling with the staples (not applicable for gang box or pre-wired installations). Do not pierce the wire with the staple as this may cause a the wall near the door control with tacks or staples. 2. Attach the manual release/safety reverse test label in a visible location on the inside of the - LiftMaster 8360W | 8360W Installation Manual - Page 19
the safety reversing sensor so beam is NO HIGHER than 6" (15 cm) above garage floor. When installing the safety reversing sensors check the following: l Sensors are installed inside the garage, one on either side of the door. l Sensors are facing each other with the lenses aligned and the receiving - LiftMaster 8360W | 8360W Installation Manual - Page 20
to the door track, the wall, or the floor. If the door track will not support the sensor bracket a wall installation is recommended. Choose one of the following installations. OPTION A DOOR TRACK INSTALLATION 1. Slide the curved arms of the sensor bracket around the edge of the door track. Snap - LiftMaster 8360W | 8360W Installation Manual - Page 21
. 1 2 (Not provided) IGWnasarildal ege 3 4 Carriage Bolt 1/4"-20 x 1/2" Wing Nut 1/4"-20 2 Wire the Safety Reversing Sensors PRE-WIRED INSTALLATIONS: If your garage already has wires installed for the safety reversing sensors, see page 22. HARDWARE Insulated Staple (Not shown) OPTION - LiftMaster 8360W | 8360W Installation Manual - Page 22
are connected to the white/black safety sensor wires to the grey terminal on the garage door opener. 1 Safety reversing sensor wires 2 Pre-installed wires 7/16" (11 mm) 3 Safety reversing sensor wires White White/Black 4 5 Yellow Purple 7/16" (11 mm) RED WHITE WHITE GREY Not Provided Pre - LiftMaster 8360W | 8360W Installation Manual - Page 23
to make it fit outlet. Be sure the opener is grounded. To avoid installation difficulties, do not activate the garage door opener at this time. To the plug doesn't fit into your outlet, contact a qualified electrician to install the proper outlet. THERE ARE TWO OPTIONS FOR CONNECTING POWER: OPTION - LiftMaster 8360W | 8360W Installation Manual - Page 24
Power 2 Ensure the Safety Reversing Sensors are Aligned The door will not close if the sensors have not been installed and aligned correctly. When the light beam is obstructed or misaligned while the door is closing, the door will reverse and the garage door opener - LiftMaster 8360W | 8360W Installation Manual - Page 25
properly installed safety reversal and DOWN buttons can be used to move the door as needed. PROGRAMMING BUTTONS UP Button Adjustment Button DOWN Button To door's downward travel, it will reverse. To watch a short instructional video on programming your new garage door opener use your smartphone to - LiftMaster 8360W | 8360W Installation Manual - Page 26
Adjustments 1 Program the Travel Without a properly installed safety reversal system, persons (particularly small children) complete up and down cycle using the remote control or the UP and DOWN buttons. Programming is complete. If you are unable to operate the door up and down, repeat - LiftMaster 8360W | 8360W Installation Manual - Page 27
on the floor, centered under the garage door. 2. Press the remote control push button to close the door. The door MUST reverse when it makes contact with the call a trained door systems technician. Without a properly installed safety reversing sensor, persons (particularly small children) could - LiftMaster 8360W | 8360W Installation Manual - Page 28
ALL electric and battery power BEFORE performing ANY service or maintenance. l Use ONLY LiftMaster part # 485LM for replacement battery. l DO NOT dispose of battery in fire. Battery may explode. Check with local codes for disposal instructions. 2 Test the Battery 1. Unplug the garage door opener - LiftMaster 8360W | 8360W Installation Manual - Page 29
power has been restored, the battery will recharge within 24 hours. The battery will last approximately 1 to 2 years with normal usage. Instructions for replacement are provided with the battery. To obtain maximum battery life and prevent damage, disconnect the battery when the garage door opener - LiftMaster 8360W | 8360W Installation Manual - Page 30
the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls. 3. ONLY activate garage door when it can be seen clearly - LiftMaster 8360W | 8360W Installation Manual - Page 31
sensors are not installed, or are misaligned, the door will not close from a remote control. However, you can close the door if you hold the button on the door blink 10 times. However, you can close the door if you hold the button on the door control or keyless entry until the door is fully closed. - LiftMaster 8360W | 8360W Installation Manual - Page 32
MyQ light controls, MyQ gate operators or MyQ commercial door operators. A LiftMaster Internet Gateway (828LM) can be added if you need to control more bar on the door control. Press and release the LEARN button OR press and release the yellow LEARN button on the garage door opener 3 times. The - LiftMaster 8360W | 8360W Installation Manual - Page 33
door controls can be connected to the garage door opener. Push Bar SERVICE LED LEARN Button LOCK Button COMMAND LED LIGHT Button Motion Sensor PUSH BAR Press the push bar to open or close the door. LIGHT BUTTON Press the LIGHT button to turn the garage door opener lights on or off. When the lights - LiftMaster 8360W | 8360W Installation Manual - Page 34
/Deactivate: Slide the motion sensor switch ON or OFF. LOCK Button LIGHT Button Command LED Motion Sensor Switch MAINTENANCE ALERT SYSTEM (MAS): Activate/Deactivate: Press and hold the LEARN button. Then press the LIGHT button. The service LED will flash the status; Active is 2 flashes and - LiftMaster 8360W | 8360W Installation Manual - Page 35
refer to the instructions provided with the accessory or visit LiftMaster.com. If your learn button. 1 LEARN button Command LED TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL USING THE LEARN BUTTON 1. Press and release the LEARN Button on the garage door opener. 2. Press and hold the button - LiftMaster 8360W | 8360W Installation Manual - Page 36
trolley from reconnecting automatically. 1. Pull the emergency release handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary. 2. To disengage the lockout feature, pull the handle straight down. The trolley will reconnect on the next UP or - LiftMaster 8360W | 8360W Installation Manual - Page 37
Maintenance Schedule The Remote Control Battery EVERY MONTH l Manually operate door. If it is unbalanced or binding, (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. This device complies with Part 15 of the FCC rules and IC RSS-210. - LiftMaster 8360W | 8360W Installation Manual - Page 38
Troubleshooting door opener will not close and the light Safety sensors are not installed, connected or wires may be cut. Inspect sensor wires for bulbs flash travel module if necessary. No movement, only a single click. Manually open and close the door. Check for binding or obstructions, such - LiftMaster 8360W | 8360W Installation Manual - Page 39
nothing is hanging or mounted on the door that would interrupt the sensor's path while closing. The garage door opener will NOT enter Wi-Fi LEARN mode: l After the initial installation of the garage door opener, the garage door opener must complete a full cycle (open and closed) before the Wi-Fi - LiftMaster 8360W | 8360W Installation Manual - Page 40
975LM Laser Garage Parking Assist: Laser enables homeowners to precisely park vehicles in the garage. 892LT/ 894LT 2 & 4 Button Learning Remote Controls: Compatible with LiftMaster® garage door openers manufactured since 1997. Also compatible with Encrypted DIP for gate applications. 485LM Mini - LiftMaster 8360W | 8360W Installation Manual - Page 41
this product. You will be advised of disassembly and shipping instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service center for warranty repair. Please include a brief description of the problem and a dated proof-of-purchase receipt with any - LiftMaster 8360W | 8360W Installation Manual - Page 42
Panel 2 Remote Control Part Number 886LMW 893LM 3 2 4 6 5 1 1 2 Installation Parts Description Part Number 1 Curved Door Arm 178B35 2 Door Bracket with Clevis Pin and White Wire 41B4494-1 10 3V CR2032 Lithium Battery 10A20 Not Shown User's Guide 114A4760 2 3 1 7 4 6 5 8 9 10 42 - LiftMaster 8360W | 8360W Installation Manual - Page 43
Repair Parts Model 8360W Garage Door Opener Parts 9 3 4 6 installation and service information call: 1-800-528-9131 Or visit us online at: LiftMaster.com or myLiftMaster.com Before calling, please have the model number of the garage door opener. If you are calling about a troubleshooting
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
 |
 |
Wi-Fi
®
Garage Door Opener
Premium Series Chain Drive Model 8360W
•
Please read this manual and the safety materials
carefully!
•
The door WILL NOT CLOSE unless the Protector
System
®
is connected and properly aligned.
•
Periodic checks of the garage door opener are
required to ensure safe operation.
•
This garage door opener is ONLY compatible with
MyQ
®
and Security+ 2.0
®
accessories.
•
DO NOT install on a one-piece door if using devices
or features providing unattended close. Unattended
devices and features are to be used ONLY with
sectional doors.
•
Attach warning labels to the location indicated on
label.
FOR RESIDENTIAL USE ONLY
LiftMaster
845 Larch Avenue
Elmhurst, Illinois 60126-1196
Register your garage door opener to receive
updates and offers from LiftMaster
Send it in
by texting
the photo to 71403 (US)
or visit
www.liftmaster.photo (Global)
Take a photo
of the camera icon
including the points (
).