LiftMaster IPAC IPAC Quick Start Manual
LiftMaster IPAC Manual
 |
View all LiftMaster IPAC manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster IPAC manual content summary:
- LiftMaster IPAC | IPAC Quick Start Manual - Page 1
Phone Number: Technical Support (IT) Contact: Phone Number: Internet & SIP Requirements This product utilizes computer network connections and communication. The site MUST have internet service and SIP service IPAC unit. We recognize there are many SIP providers and LiftMaster installation manual. - LiftMaster IPAC | IPAC Quick Start Manual - Page 2
web browser,enter the IP address assigned to the unit. Read and accept the LiftMaster agreement. For initial login, enter "admin" as the user name, and leave for the Door. 14 Configure IPAC Navigate to: Configuration>Hardware>Devices>Create New Device>select IPAC Device. Enter the SIP account
-
1 -
2
 |
 |
1 2 3 4
ON
CONFIG
SHLD
NC
COM
NO
COM
NO
PWR IN
SHLD
NC
COM
NO
RELAY 1
SHLD
NC
COM
NO
AUX 1
SHLD
2
Remove the Unit
Lift the unit out of the carton and place it face
down in the carton.
3
Remove the Knockouts
Use a punch tool that is one inch or less to
remove knockouts based on your installation
requirements.
4
Mount the Unit
Mount the unit securely to a flat surface or
pedestal using the proper installation method
listed in the installation manual. Make sure unit
is properly sealed.
5
Connect Devices
Connect any maglocks, door strikes, operators or
accessories to the relay board.
6
Connect Power
Connect the transformer to the PWR IN terminal
block on the relay board.
7
Connect Ethernet
Connect the LAN to the LAN port on the
peripheral board.
8
Switch to Program Mode
Switch into program mode by setting switch #1
on the peripheral board to ON.
INSTALLATION
(open enclosure)
Power Wires
Switches
Ethernet Cable
Relay 1
Aux 1
Relay Board
Relay Board
Peripheral Board
Peripheral Board
CONNECT
9
Setup Network
Use the Site Survey to fill out the
networking information in the
administrative screen. Confirm settings in
the Network Diagnostics tab.
1
Complete Site Survey
The Site Survey is available in the
installation manual or online.
Site Survey
The purpose of the site survey is to:
•
Determine if a site meets all the requirements for the
installation of the access control panel.
•
Identify any missing requirements at the site.
•
Record the network settings used to configure the
access control panel.
•
Determine the location of the access control panel.
•
Determine if any optional equipment is needed for the site.
This product is a network enabled and Internet ready access control solution for community doors and gates that features a simple and
intuitive resident and visitor experience.
Internet & SIP Requirements
Document Objectives
Site Information
Overview
This product utilizes computer network connections and communication. The site MUST have internet service and SIP service for the
access control panel to operate.
INTERNET SERVICE:
SIP SERVICE:
Yes – The site has internet service.
Yes – The site has SIP service.
No – Order internet service.
No – Order SIP service.
NETWORK CONNECTION:
The access control panel MUST be connected to a 10/100 (minimum) local area network (LAN) device such as a hub, switch or router
with a CAT 5/6 network cable. The LAN port on the main board is a 10/100 Ethernet interface with an RJ45 jack.
Yes – The site has access to a LAN device. Where is the LAN device located?
No – Setup a network device such as a hub, switch or router on site.
NETWORK SETTINGS:
The access control panel MUST be configured with the proper network settings to operate. Contact the site’s IT personnel for the
corresponding settings and record the settings below. DHCP is not recommended because the IP address might inadvertently change
after power cycle or if the router is reset.
The SIP providers listed in this document are the currently known providers that will work with the IPAC unit. We recognize there are
many SIP providers and LiftMaster is not endorsing the use of any one particular SIP provider. The SIP providers are only listed
as a convenience for the installer.
Site Name:
Address:
Site Contact:
Phone Number:
Technical Support (IT) Contact:
Phone Number:
Survey By:
Survey Date:
Proposed Install date:
Internet service provider:
IP Address: ________ . ________ . ________ . ________
Netmask: ________ . ________ . ________ . ________
Gateway: ________ . ________ . ________ . ________
Primary DNS: ________ . ________ . ________ . ________
Secondary DNS: ________ . ________ . ________ . ________
Server Port:
SIP service provider:
Known compatible SIP providers: didlogic and phone.com
SIP domain:
SIP port (usually 6050):
SIP username:
SIP password:
1
10
Exit Program Mode
Switch out of program mode by setting switch #1
on the peripheral board to OFF.
1 2 3 4
ON
CONFIG
Switches
Peripheral Board
(open enclosure)