LiftMaster SL595 SL595 Manual - Page 31

THREE PHASE WIRING DIAGRAM 3 PHASE POWER IN ON/OFF SWITCH L1 (BK) L2 (BK) L3 (BK) GROUND (GN) WARNING To protect against fire and electrocution: • DISCONNECT power BEFORE installing or servicing operator. • Replace ONLY with fuse of same type and rating. Fuse: 3AG, 3.2A, 120V, SLO-BLO (SEE NOTE 3) OVERLOAD (BK) (BK) 4B3 4A3 5A 6 1B 2 (BK) (BK) 2A1 6B5 SEE NOTE 3 (BK) BLACK (SL595 ORANGE) (SEE PRIMARY (WH) NOTE 2) (BL) 24V Sec. (SEE NOTE 1) FUSE (YE) 3.2A (BL) (TB 2) AB CD 230V CONNECTION (GY) (SL595 GN) (BK) (PU) (SL595 RD) (BK) (YE) (SL595 WH) 1 74 2 85 3 96 460V CONNECTION (GY) (SL595 GN) 1 (BK) 2 (PU) (SL595 RD) (BK) (YE) (SL595 WH) 3 (SEE NOTE 3) 74 85 96 575V CONNECTION (GY) (SL595 GN) 1 (BK) 2 (PU) (SL595 RD) (BK) (YE) (SL595 WH) 3 (SEE NOTE 3) 230V BRAKE SOLENOID 230V BRAKE SOLENOID 575V BRAKE SOLENOID FACTORY INSTALLED RADIO RADIO BLOCK (BL) (BL) (BK) (BK) (YE) (YE) (YE) (YE) (RD) (RD) 24VAC RADIO SIGNAL R1 (BL) R2 (BL) (YE) R3 (Y/BK) R4 (BRN) SAFETY ALARM (100 db) - (BK) + (RD) (SEE NOTE 4) 4 (GN) 6 (WH ) 7 (RD) 8 (BK) 9 (BRN) 10 (GY) FREE EXIT LOOP HARNESS 10 PIN - 1,2,3,5 CAPPED GL CONTROL BOARD J2 PLUG 24VAC-IN 24VAC-COMMON SOFT OPEN NC "B" LIMIT CONTACTOR B J2- 3 J2- 4 J2- 5 J2- 6 J2- 7 J2- 1 (BL) (YE) (GN) 3 L/S B (PU) 2 (PU) NC COM "A" LIMIT J2-8 CONTACTOR A J2-2 L/S A (OR) 1 NC COM (OR) RPM - IN RPM - SUPPLY RPM GND J2- 9 J2-10 J2- 11 (WH) (RD) (BK) RPM SENSOR J1 PLUG RADIO COMMAND J1-1 (PU) (Y/BK) (YE) A1 B A2 A A1 A2 OPEN CLOSE (Y/BK) (OR) (GN) SHADOW J1-2 (PU/WH) +24VDC J1-3 CLOSE J1-4 (Y/BK) (GN) 4 (GN) 6 (WH ) 7 (RD) 8 (BK) 9 (BRN) 10 (GY) INTERRUPT (SAFETY) LOOP HARNESS 10 PIN - 1,2,3,5 CAPPED (PU) (WH) (P/W) (Y/BK) (Y/BK) (GN) FIELD CONNECTIONS TB1 1 RADIO 2 SHADOW 3 VDC COM 4 CLOSE STOP J1-5 SOFT OPEN J1-6 (Y/BK) (BRN) STOP (Y/BK) RESET (Y/BK) 5 (WH) STOP/COM (BRN) 6 SOFT OPEN HARD OPEN J1-7 (OR) INT. LOOP J1-8 (GN) (OR) 7 HARD OPEN (GN) 8 INTERRUPT (SAFETY) OBS. OPEN OBS. CLOSE J1-9 J1-10 (GY) (OR/BK) (GY) 9 (OR/BK) 10 OPEN EDGE/PHOTOEYE (SAFETY) CLOSE 24 VAC-COMMON J1-11 DC-GND J1-12 (WH) 11 (RD) 12 MASTER / SECOND LOCK 1 J1-13 (BK) LOCK 1 J1-14 (BK) ALARM 1 J1-15 (BL) ALARM 1 J1-16 (RD) (BK) 13 (BK) 14 (BL) 15 (YE) 16 MAGLOCK 24 VAC J4 PLUG DUAL 1 (WH) GATE 2 (RD) = TERMINAL BLOCK IN LIMIT SWITCH ENCLOSURE (SL595 ONLY). (GY) 17 (BRN) 18 (GY) 19 (BRN) 20 INTERRUPT LOOP (SAFETY) EXIT LOOP NOTES: 1. Transformer primary voltage is the same as the operator line voltage. Secondary 24V 60VA. 2. Wire color: 208V red, 230V orange, 460V purple, 575V gray. 3. Three phase units are equipped with an internal pilot duty thermal overload device or an external line monitoring device. 4. When using a remote control or Single Button Control Station in lieu of the Soft Open feature, perform the following modifications to the operator: 1. Remove the green wire from R4 of the radio block and mount the wire to terminal block TB1 position 6. 2. Move the brown wire on Terminal Block TB1 position 6 (from radio block R4) to Terminal Block TB1 position 1. 31