LiftMaster SRDRST LiftMaster Smart Reader Installation Guide - English French
LiftMaster SRDRST Manual
 |
View all LiftMaster SRDRST manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster SRDRST manual content summary:
- LiftMaster SRDRST | LiftMaster Smart Reader Installation Guide - English French - Page 1
SMART READER INSTALLATION GUIDE Included Parts: • Reader, Backplate, Wall Plate • #6 Machine Screws - QTY 2 • #6 Self Tapping Screws - QTY 2 • #4-40 Phillips Screw • #4-40 Pin-in-Torx Screw Tools Needed (Not Supplies): • - LiftMaster SRDRST | LiftMaster Smart Reader Installation Guide - English French - Page 2
technologies built in the reader: First, an LED sequence will indicate the supported RF protocols. BLE High-Frequency Low-Frequency Red LED flash Green LED and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there - LiftMaster SRDRST | LiftMaster Smart Reader Installation Guide - English French - Page 3
GUIDE D'INSTALLATION DU LECTEUR SMART Pièces incluses : • Lecteur, plaque arrière, plaque murale • Vis mécaniques n° 6 - QTÉ 2 • Vis autotaraudeuses n° 6 - QTÉ 2 • Vis hexagonale n° 4-40 • Vis Pin-in- - LiftMaster SRDRST | LiftMaster Smart Reader Installation Guide - English French - Page 4
de configuration (CPN) du lecteur sur l'étiquette contrôle les données de support de la carte à puce. Des détails techniques supplémentaires et l'information réglementaire n'est pas installé et utilisé conformément aux instructions, il risque de causer des interférences nuisibles aux communications - LiftMaster SRDRST | LiftMaster Smart Reader Installation Guide - English French - Page 5
GUÍA DE INSTALACIÓN DEL LECTOR INTELIGENTE Piezas incluidas: • Lector, placa posterior y placa para la pared • Tornillos de máquina n.º 6 (2 unidades) • Tornillos autorroscantes n.º 6 (2 unidades) • Tornillo Phillips n.º 4-40 • Tornillo Torx n.º 4-40 Herramientas necesarias (no incluidas): • - LiftMaster SRDRST | LiftMaster Smart Reader Installation Guide - English French - Page 6
Secuencia de arranque del lector Al encenderse, los lectores inteligentes presentan una secuencia de LED y pitidos para informar sobre el tipo de lector y su modo de comunicación. En la primera secuencia se describe la tecnología de radiofrecuencia integrada al lector: En primer lugar, una secuencia
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
1
SMART READER
INSTALLATION GUIDE
Included Parts:
• Reader, Backplate, Wall Plate
•
#6 Machine Screws – QTY 2
•
#6 Self Tapping Screws – QTY 2
• #4-40 Phillips Screw
• #4-40 Pin-in-Torx Screw
Wiring Connections
Red
Power In
Black
Ground
Shield
Shield Ground
Green
Wiegand Data 0
RS485A(+)
White
Wiegand Data 1
RS485A(–)
Yellow*
Beeper Control
Brown*
Tamper Out
Blue*
Green LED Control
Orange
*
Red LED Control
•
Single Gang
Keypad
RF TECHNOLOGIES
Model
Model
125 kHz, 13.56 MHz & BLE Mobile
SRDRST
SRDRKP
CURRENT
120 mA average, 170 mA peak
145 mA average, 195 mA peak
VOLTAGE
5-16 VDC (NEVER APPLY MORE THAN 16V)
TEMPERATURE
UL™ tested –35° to 66°C and EN –40° to 70°C and 95% humidity
(UL™ tested -31˚F to 150˚F and EN -40˚ to 158˚F and 95% humidity)
CABLE LENGTH
Communication Lines
Wiegand:
200 feet - 22 AW G
300 feet - 20 AWG
500 feet -18 AWG
OSDP @ 12 VDC and 25˚C (77˚F)
= 1000 feet - 22 AWG Twisted Pair
NOTE:
Do NOT use the Power Supply provided with the CAPXLV or CAPXM to directly power up this reader. It is 24V and will cause damage to the reader.
NOTE:
LED Control not available when connected to a CAPXS.
Tools Needed (Not Supplies):
• Phillips Screwdriver
•
1” (25 mm), 1/8” Drill bits
•
T8 Security Torx Bit (optional for increased tamper detection)
• #6-32 Tap if required
*These wires are only used in Wiegand mode.
**All wiring methods used shall be in accordance
with the National Electrical Code, ANSI/NFPA 70.
Readers must be powered by a compatible UL
Listed, power limited, access control panel rated
5–16 VDC.
A.
Install the Metal Wall Plate to the Wall/Single Gang box.
• Use the provided #6 screws.
B.
Wire the Cable to the Control Panel.
C.
Attach the Reader to the Wall Plate and Install the Reader Screw.
•
Follow steps 1 through 3 below to ensure proper alignment. Install either the #4-40
screw or Pin-in-Torx screw at the bottom.
WARNING:
This product can expose you to chemicals including lead, which are known
to the State of California to cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.