Maytag MBF1958FEW Dimension Guide
Maytag MBF1958FEW Manual
 |
View all Maytag MBF1958FEW manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MBF1958FEW manual content summary:
- Maytag MBF1958FEW | Dimension Guide - Page 1
connections. If you are installing your refrigerator next to a fixed wall, leave 2Z⁄x" (6.3 cm) minimum on the hinge side (depending on your model) to allow for the door to purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice
-
1
 |
 |
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
Bottom Mount Refrigerator
MBF1958
MBF2258
MBR1957FE
Electrical:
A 115-volt, 60-Hz, AC-only, 15-
or 20-amp fused, grounded electrical
supply is required. It is recommended
that
a separate circuit serving only your
refrigerator be provided. Use an outlet that
cannot be turned off by a switch. Do not
use an extension cord.
NOTE:
Before performing any type of
installation, cleaning, or removing a
light bulb, turn the control (Thermostat,
Refrigerator or Freezer Control depending
on the model) to OFF and then disconnect
the refrigerator from the electrical source.
When you are finished, reconnect the
refrigerator to the electrical source and
reset the control (Thermostat, Refrigerator
or Freezer Control depending on the
model) to the desired setting. See “Using
the Controls.”
Water:
A cold water supply with water
pressure between 30 and 120 psi (207 and
827 kPa) is required to operate ice maker
and water dispenser. If you have questions
about your water pressure, call a licensed,
qualified plumber.
IMPORTANT:
The
pressure of the water coming out of a
reverse osmosis system going to the water
inlet valve of the refrigerator needs to be
between 30 and 120 psi (207 and 827
kPa).
Reverse Osmosis Water Supply:
If a reverse osmosis water filtration system
is connected to your cold water supply, the
water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60
psi (276 to 414 kPa).
To ensure proper ventilation for your refrigerator, allow for a
Z⁄x
" (1.25 cm) space on each side and
at the top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your refrigerator has
an ice maker, make sure you leave some extra space at the back for the water line connections.
If you are installing your refrigerator next to a fixed wall, leave 2
Z⁄x
" (6.3 cm) minimum on the hinge
side (depending on your model) to allow for the door to swing open.
NOTE:
It is recommended that you do not install the refrigerator near an oven, radiator, or other
heat source, nor in a location where the temperature will fall below 55°F (13°C).
LOCATION REQUIREMENTS
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10621529
A
10
/1
6
4
1
A
overall
B
top of
cabinet
H
not incl.
handle
F
incl.
handle
E
D
cabinet
G
90˚
C
Model
Number
Model Size
Height -
Overall
“A”
Height -
Top of
Cabinet
“B”
Depth -
Doors Open
90°
“C”
Depth -
Drawer
Open
“D”
Depth -
With
Handles
“E”
Depth -
Without
Handles
“F”
Depth -
Cabinet
Only
“G”
Width -
Cabinet
“H”
MBF1958
MBR1957FE
18.7 cu. ft.
67"
(170.2 cm)
65
Z⁄x
"
(166.4 cm)
59"
(149.9 cm)
50
C⁄v
"
(128.9 cm)
33
C⁄,
"
(84.8 cm)
30
M⁄,
"
(78.4 cm)
28
Z⁄,
"
(71.4 cm)
29
⁵⁄₈
"
(75.
2
cm)
MBF2258
22.1 cu. ft
70"
(177.8 cm)
68
Z⁄x
"
(174.0 cm)
62"
(157.5 cm)
50
C⁄v
"
(128.9 cm)
33
C⁄,
"
(84.8 cm)
30
M⁄,
"
(78.4 cm)
28
Z⁄,
"
(71.4 cm)
32
B⁄,
"
(82.9 cm)
2
¹/₂
" (6.3 cm)
¹/₂
" (1.25 cm)