Maytag MEDB955F Quick Reference Sheet

W11356714A

W11356717A-SP

Dryer Quick Start Guide

OPERATING INSTRUCTIONS

WARNING

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil

on it (including cooking oils).

Items containing foam, rubber, or plastic must be

dried on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in

death or fire.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in

death, explosion, or fire.

WARNING:

To reduce the risk of fire, electric shock, or injury to persons,

read the IMPORTANT SAFETY INSTRUCTIONS, located in your

appliance's Owner's Manual, before operating this appliance.

Step 1.

Clean Lint Screen

Step 2.

Load Clothes; then Close

Door

Step 3.

Power On/Cancel

Step 4.

Select Cycle and Settings

Step 5.

Press Start/Pause

Cycle Guide – Normal Cycle

Senses moisture in the load and shuts off when the load reaches the selected dryness level. The dry temperature

shown is the default temperature. This setting can be modified on some cycles but is not retained for future drying

with this cycle. The dryness setting can be changed on some cycles and will be retained for future drying with this

cycle.

To get the most energy savings and enhanced fabric care from your dryer, use the Sensing cycles. These cycles

measure the drying air temperature and moisture levels to turn the dryer off once the load reaches the selected

dryness level. For electric models, dryer performance and results may vary with service voltage less than 240.

Items to Dry:

Cycle:

Temperature:

Description:

Work clothes,

casual wear, mixed

cottons, sheets,

corduroys

Normal

Medium

Starts at High heat, quickly goes to Medium High, and

then ends on Medium heat to dry large loads of mixed

fabrics and items. Normal is the preferred energy

cycle. Energy Saver defaults on. To reduce cycle time,

at the cost of energy savings, turn Energy Saver off.

NOTE:

Options Static Reduce and Steam Boost

cannot be used at the same time.

You may select Wrinkle Prevent “With Steam”, on some models, to add a short steam cycle after 60 minutes. This

is not available on Sanitize or Delicates. Wrinkle Prevent without Steam will be run to keep optimal clothes

protected/performance.

NOTE:

Government Energy Certifications for the Gas and Electric models were based on the Timed Dry Cycle with

the Maximum Drying Temperature Setting. The as-shipped defaults of AccuDry

™

, Automatic Dry, Auto Moisture

Sensing or Sensor Dry, Normal or Energy Preferred Cycle, Low Heat, Wrinkle Guard or Wrinkle Prevent were not

used.

Online Ordering Information

For detailed installation instruction and maintenance information, winter storage, and transportation tips, please

see the Owner’s Manual included with your machine.

For information on any of the following items, the full cycle guide, detailed product dimensions, or for complete

instructions for use and installation, please visit https://www.maytag.com/owners, or in Canada

https://www.maytag.ca/owners. This may save you the cost of a service call.

However, if you need to contact us, use the information listed below for the appropriate region.

United States:

1–800–344–1274

Maytag Brand Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022–2692

Canada:

1–800–688–2002

Maytag Brand Appliances

Customer eXperience Centre

200–6750 Century Ave.

Mississauga, Ontario L5N 0B7

Button Descriptions

1.

POWER/CANCEL

Touch to turn the dryer on and off. Touch to stop/cancel a cycle at any time.

2.

CYCLE CONTROL KNOB

Use the Cycle Control knob to select available cycles on your dryer. Turn the

knob to select a cycle for your laundry load. See the online “Cycle Guide” for

details.

3.

START/PAUSE

Touch and hold until the LED comes on to start a cycle, or touch once while a

cycle is in process to pause it.

4.

TIMED DRY ADJUST

Touch “+” or “–” with Timed Dry Cycles to increase or decrease the length of a

Timed Dry or Rapid Dry cycle.

5.

LED DISPLAY

When you select a cycle, its default settings will light up and the estimated time

remaining (for Sensor cycles) or actual time remaining (for Timed cycles) will

be displayed.

Not all features, cycles, and options are available on all models. Appearance may vary.

NOTE:

The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, touch the control

panel with your finger tip, not your fingernail. When selecting a setting or option, simply touch its name.

6.

SETTINGS

Touch the setting names next to the display to adjust settings. Not all settings

are available with all cycles. See the online “Cycle Guide” for details.

Temperature:

Timed Dry

When using Timed Cycles, you may select a dry temperature based on the type

of load you are drying. Use the warmest setting safe for the garments in the

load. Follow garment label instructions.

Sensor Cycles

Sensor Cycles allow temperature adjustment. At most four of available

temperatures (not including Air Only) are allowed.

Dry Level

You may adjust the Dry Level on Sensor Cycles only (except for the Sanitize and

Steam Refresh cycles), if desired.

Wrinkle Prevent

If you will be unable to remove a load immediately, touch Wrinkle Prevent to add

up to 150 minutes of periodic tumbling to help reduce wrinkling. On some cycles,

you may select the “With Steam” setting to add a short steam cycle after 60

minutes to help smooth out wrinkles.

NOTE:

If the Wrinkle Prevent option is selected, it is active even if the Done

indicator is lit. If you open the dryer door prior to the end of the Wrinkle Prevent

option, the dryer will go into Pause mode. You will need to touch Power to turn

off or touch Start/Pause to continue the Wrinkle Prevent option. If the Wrinkle

Prevent option is paused, it will discontinue after 5 minutes of inactivity and turn

off.

Audio Level

Touch Audio Level to move the volume of the end signal and button sounds

between 5 different settings, including off.

7.

OPTIONS

Use to select available options for your dryer.

My Cycle

If you have a favorite cycle with custom settings that you use frequently, you can

use the My Cycle feature to keep your preferred settings ready to use. To save

the cycle, press and hold My Cycle (approximately 3 seconds) until a beep

sounds and My Cycle LED is lit. Once a configuration has been saved, you may

power on the machine and briefly press My Cycle to load your saved cycle and

settings.

Energy Saver

Touch to activate the Energy saver settings to increase your energy savings.

Energy Saver is only available for the Normal cycle. For optimal energy turn on

the Energy Saver option

NOTE:

Energy savings may vary across loads.

Static Reduce

Touch to add the Static Reduce option to selected Sensor Cycles.(see online

“Cycle Guide” for details). The dryer will automatically tumble, pause, and

introduce a small amount of moisture into the load to help reduce static. This

option adds approximately 8 minutes to the total cycle time.

Steam Boost

Steam Boost adds steam to the end of the cycle to help smooth wrinkles. See

online “Cycle Guide” for details.

Damp Dry Signal

Touch to select the Damp Dry Signal to on or off. When selected, a series of

beeps will sound when the load is damp, but not completely dry. This will allow

you to take clothes out of the load that do not need to dry completely. This signal

can also be used as a signal to rearrange the load when drying large bulky

items that do not tumble well, such as comforters. This option is not available on

Sanitize, Steam Refresh and Timed Dry cycles.

Drum Light

Select Drum Light to turn on the light inside the dryer drum. When touched

during a cycle, or when the dryer is not running, the Drum Light turns on and will

remain on until Drum Light is touched again, the door is opened and closed, a

cycle is started, or the door is left open for 5 minutes. Touch Drum Light at any

time to turn the drum light on or off.

8.

CYCLE STATUS

The Cycle Status indicators show the progress of a cycle. Touch a button for the

desired drying cycle. Not all indicators are available on all models. See the

online “Cycle Guide” for cycle details.

Sensing

The Sensing indicator will light during Automatic/Sensor Cycles to indicate that

the moisture sensor on the dryer is operating. This indicator will not light during

Timed Cycles or options such as Wrinkle Prevent.

Check Vent

The Check Vent indicator will light if there is a blocked vent or low airflow.

Good Airflow

This indicator will light if there is no major vent blockage.

Steam

This indicator will light when a steam function is active.

NOTE:

Steam is not available on all cycles or models.

Done

This will indicate that the selected cycle has ended and the load may be

removed from the dryer. If Wrinkle Prevent has been selected, the dryer may

continue to tumble the load, even if the Done indicator is lit.

Check Lint Screen

The Check Lint Screen indicator light will turn on as a reminder to clean the lint

screen. It will turn on until the door is opened or a cycle is started. It will turn off

when the dryer is turned Off.

Section	Page
Dryer Quick Start Guide	1
Operating Instructions_W11356714 New	1
Guide de démarrage rapide de la sécheuse	2

Maytag MEDB955F Quick Reference Sheet

Maytag MEDB955F Manual

Maytag MEDB955F manual content summary: