Home » Maytag Manuals » Ranges » Maytag MER8600DS » Manual Viewer

Maytag MER8600DS Installation Guide

Maytag MER8600DS Manual

View all Maytag MER8600DS manuals

Add to My Manuals
Save this manual to your list of manuals

Maytag MER8600DS manual content summary:

Maytag MER8600DS | Installation Guide - Page 1
INSTALLATION INSTRUCTIONS 30" (76 CM) FREESTANDING ELECTRIC RANGES Table of Contents RANGE SAFETY 2 INSTALLATION REQUIREMENTS 3 Tools and Parts 3 Location Requirements 3 Electrical Requirements - U.S.A. Only 5 INSTALLATION INSTRUCTIONS 6 Unpack Range 6 Install Anti-Tip Bracket 6 Electrical
Maytag MER8600DS | Installation Guide - Page 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual anti-tip bracket if range is moved. Do not operate range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death
Maytag MER8600DS | Installation Guide - Page 3
. Mobile home installations require: ■ When this range is installed in a mobile home, it must be secured per the instructions in this document. ■ Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See "Electrical Connection
Maytag MER8600DS | Installation Guide - Page 4
E. 25 64.3 cm) depth - back of range to front of cooktop** F. Model/serial rating plate (located on the frame behind a top corner of the door or either side of the drawer) IMPORTANT: Range must be level after installation. Follow the instructions in the "Level Range" section. Using the cooktop as
Maytag MER8600DS | Installation Guide - Page 5
To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. ■ Range must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate. The model/serial rating
Maytag MER8600DS | Installation Guide - Page 6
INSTALLATION INSTRUCTIONS Unpack Range WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not
Maytag MER8600DS | Installation Guide - Page 7
Move range close enough to opening to allow for final electrical connections. Remove shipping base, cardboard or hardboard from under range. 7. Move range into range forward onto shipping base, cardboard or hardboard to continue installing the range using the following installation instructions.
Maytag MER8600DS | Installation Guide - Page 8
and toward you to remove cover from range. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock. Style 1: Power supply cord strain relief
Maytag MER8600DS | Installation Guide - Page 9
Part of metal ground strap must be cut out and removed. 5. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) Electrical Connection Options If your home plate on bottom of range. Allow enough slack to
Maytag MER8600DS | Installation Guide - Page 10
of the 10-32 hex nuts. 2. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. Installation: Copper or Aluminum Wire This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical
Maytag MER8600DS | Installation Guide - Page 11
Part of metal ground strap must be cut out and removed. A B C A. Metal ground strap B. Discard C. Ground-link screw 2. Use a Phillips screwdriver to remove the ground-link screw from the back of the range ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with
Maytag MER8600DS | Installation Guide - Page 12
Installed and Engaged On Ranges range forward and determine if there is an obstruction between the range and the mounting wall. If you need assistance or service, refer to the "Assistance or Service" section of the Use and Care Guide, or the cover or "Warranty" section of the User Instructions
Maytag MER8600DS | Installation Guide - Page 13
. Do not operate the range without anti-tip bracket installed and engaged. Please reference the "Assistance or Service" section of the Use and Care Guide, or the cover or "Warranty" section of the User Instructions, to contact service. Level Range Determine if you have AquaLift® Technology or Steam
Maytag MER8600DS | Installation Guide - Page 14
an "F9" or "F9, E0" error code, the electrical outlet in the home may be miswired. Contact a qualified electrician to verify the electrical supply. ■ See the "Troubleshooting" section in the Use and Care Guide or User Instructions. When the range has been on for 5 minutes, check for heat. If
Maytag MER8600DS | Installation Guide - Page 15
supply cord. 5. Check that the anti-tip bracket is installed and engaged. See the "Verify Anti-Tip Bracket Is Installed and Engaged" section. 6. Check that range is level. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can
Maytag MER8600DS | Installation Guide - Page 16
W10403811C ®/™ ©2012 Whirlpool. All rights reserved. 8/12 Printed in U.S.A.