Home » Maytag Manuals » Ranges » Maytag MER8670AS » Manual Viewer

Maytag MER8670AS Installation Guide

Maytag MER8670AS Manual

View all Maytag MER8670AS manuals

Add to My Manuals
Save this manual to your list of manuals

Maytag MER8670AS manual content summary:

Maytag MER8670AS | Installation Guide - Page 1
FREESTANDING ELECTRIC RANGES Table of Contents RANGE SAFETY 2 INSTALLATION REQUIREMENTS 3 Tools and Parts 3 Location Requirements 3 Electrical Requirements - U.S.A. Only 5 INSTALLATION INSTRUCTIONS 6 Unpack Range 6 Install Anti-Tip Bracket 6 Electrical Connection - U.S.A. Only 8 Verify Anti
Maytag MER8670AS | Installation Guide - Page 2
important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the reduce the chance of injury, and tell you what can happen if the instructions are not followed. Range Foot WARNING Tip Over Hazard A child or
Maytag MER8670AS | Installation Guide - Page 3
wall. Thickness of flooring may require longer screws to anchor bracket to floor. Parts needed If using a power supply cord kit: ■ A UL listed power per the instructions in this document. ■ Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will
Maytag MER8670AS | Installation Guide - Page 4
left side frame behind storage drawer or right side of frame behind the oven door) IMPORTANT: Range must be level after installation. Follow the instructions in the "Level Range" section. Using the cooktop as a reference for leveling the range is not recommended. *Range can be raised approximately
Maytag MER8670AS | Installation Guide - Page 5
shock. Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do not modify the the type of electrical connection you will be using and follow the instructions provided for it here. This range is manufactured with the ground
Maytag MER8670AS | Installation Guide - Page 6
1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not remove the shipping base at this time. killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the
Maytag MER8670AS | Installation Guide - Page 7
leveling leg slides into anti-tip bracket. 8. Move range forward onto shipping base, cardboard or hardboard to continue installing the range using the following installation instructions. Rear position Front position Diagonal (2 options) 7
Maytag MER8670AS | Installation Guide - Page 8
new 40 amp power supply cord. Plug into a grounded outlet. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range. Failure to follow these
Maytag MER8670AS | Installation Guide - Page 9
relief screw against the flexible conduit. 5. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Part of metal ground strap must be cut out and removed. A B C
Maytag MER8670AS | Installation Guide - Page 10
5. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. 2. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. A F A E B C E D A. 10-32 hex nut B.
Maytag MER8670AS | Installation Guide - Page 11
: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Part of metal ground strap must be cut out and removed. 4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires
Maytag MER8670AS | Installation Guide - Page 12
3-wire connection: Direct Wire Use this method only if local codes permit connecting ground conductor to neutral supply wire. 1. Pull the wires through the conduit on cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block. A 3. Use ³⁄₈" nut
Maytag MER8670AS | Installation Guide - Page 13
range without anti-tip bracket installed and engaged. Please reference the "Assistance or Service" section of the Use and Care Guide, or the cover or "Warranty" section of the User Instructions, to contact service. Level Range Determine if you have AquaLift™ Technology or Steam Clean by referring
Maytag MER8670AS | Installation Guide - Page 14
, it is not suggested to remove the oven door. However, if removal is necessary, make sure the oven is off and cool. Then, follow these instructions. The oven door is heavy. To Remove: 1. Open oven door all the way. 2. Pinch the hinge latch between two fingers and pull forward. Repeat on
Maytag MER8670AS | Installation Guide - Page 15
to verify the electrical supply. ■ See the "Troubleshooting" section in the Use and Care Guide or User Instructions. When the range has been on for 5 ranges: WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can
Maytag MER8670AS | Installation Guide - Page 16
W10403811B © 2011. All rights reserved. TM AQUALIFT is a trademark of Whirlpool, U.S.A. 12/11 Printed in U.S.A.