Maytag MET8775XB Installation Instructions
Maytag MET8775XB Manual
 |
View all Maytag MET8775XB manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MET8775XB manual content summary:
- Maytag MET8775XB | Installation Instructions - Page 1
FREESTANDING ELECTRIC RANGE WITH DOUBLE OVENS INSTRUCTIONS D'INSTALLATION POUR CUISINIÈRE ÉLECTRIQUE AUTOPORTANTE AVEC FOURS DOUBLES of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is - Maytag MET8775XB | Installation Instructions - Page 2
range is moved. Failure to follow these instructions can result in death or serious burns to ■ Oven racks ■ 2 - #12 x 1⁵⁄₈" screws (for mounting anti-tip bracket) ■ Anti-tip bracket (taped inside upper oven with clearances specified on the model/serial rating plate. The model/serial rating plate is - Maytag MET8775XB | Installation Instructions - Page 3
instructions for (2.5 cm) by adjusting the leveling legs. **Model/serial/rating plates may be rotated up from behind Dimension given is from wall to front of oven door and will vary based on electric outlet less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum - Maytag MET8775XB | Installation Instructions - Page 4
instructions provided for it here. ■ Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model slack in the line so that the range can be moved if servicing is ever necessary. ■ A UL listed conduit connector must be - Maytag MET8775XB | Installation Instructions - Page 5
Supply Cord Kit and Circuit Protection Amps 40 or 50** 50 *The NEC calculated load is less than the total connected load listed on the model/serial rating plate. **If connecting to a 50-amp circuit, use a 50-amp rated cord with kit. For 50-amp rated cord kits, use kits that - Maytag MET8775XB | Installation Instructions - Page 6
INSTRUCTIONS Unpack Range WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from the range. Keep cardboard bottom under range. 2. Remove oven the range supported on 2 - Maytag MET8775XB | Installation Instructions - Page 7
Install Anti-Tip Bracket 1. Remove the anti-tip bracket that is taped inside the upper oven with the package containing literature. Floor Mounting 2. Determine which mounting method to use: floor or wall. If you have a stone or masonry floor you can - Maytag MET8775XB | Installation Instructions - Page 8
new 40 amp power supply cord. Plug into a grounded outlet. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range. Failure to follow these - Maytag MET8775XB | Installation Instructions - Page 9
Assemble a UL listed conduit connector in the opening. 5. Replace back panel and screws on rear of range. 6. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) Electrical Connection Options If your home has - Maytag MET8775XB | Installation Instructions - Page 10
4-wire connection: Power Supply Cord Use this method for: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Part of metal ground strap must be cut out and removed. 5. Use ³⁄₈" nut driver to - Maytag MET8775XB | Installation Instructions - Page 11
2. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. A E D B C A. 10-32 hex nut B. Line 1 (black) C. Ground-link screw D. Neutral (white) wire E. Line 2 (red) 3. Connect line 1 (black) and line 2 (red) wires to the outer - Maytag MET8775XB | Installation Instructions - Page 12
4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to XX lbs-in. torque. See Bare Wire Torque Specifications - Maytag MET8775XB | Installation Instructions - Page 13
. Check that the flexible conduit or power supply cord are not bent. 8. Turn power on. Turn on surface elements and oven. See the Use and Care Guide for specific instruction on range operation. If range does not operate, check the following: ■ Household fuse is intact and tight; or circuit breaker - Maytag MET8775XB | Installation Instructions - Page 14
anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults. When foot is under anti-tip bracket. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so - Maytag MET8775XB | Installation Instructions - Page 15
Notes 15 - Maytag MET8775XB | Installation Instructions - Page 16
est le danger potentiel et vous disent comment réduire le risque de blessure et ce qui peut se produire en cas de non-respect des instructions. AVERTISSEMENT Risque de basculement Un enfant ou une personne adulte peut faire basculer la cuisinière ce qui peut causer un décès. Joindre la bride - Maytag MET8775XB | Installation Instructions - Page 17
èces nécessaires avant d'entreprendre l'installation. Lire et suivre les instructions fournies avec chacun des outils de la liste ci-dessous. Outils (homologation UL) conçu pour l'utilisation avec une cuisinière. Pour service 250 volts minimum, 40 A ou 50 A, compatible avec une ouverture - Maytag MET8775XB | Installation Instructions - Page 18
36" (91,4 cm) IMPORTANT : En cas d'installation d'une hotte ou d'un ensemble hotte/micro-ondes au-dessus de la cuisinière, suivre les instructions fournies avec la hotte concernant les dimensions de dégagement à respecter au-dessus de la surface de la table de cuisson. Une cuisinière autoportante - Maytag MET8775XB | Installation Instructions - Page 19
Spécifications électriques - Canada seulement WARNING ■ En cas de doute quant à la qualité de la liaison à la terre de la cuisinière, consulter un électricien qualifié. Puissance nominale de la cuisinière* Intensité nominale spécifiée du cordon d'alimentation et de la protection du circuit 120/ - Maytag MET8775XB | Installation Instructions - Page 20
personnes pour déplacer et installer la cuisinière. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure. 1. Ôter les plancher dans le sens de la longueur derrière la cuisinière en guise de support lorsque la cuisinière est placée sur sa partie postérieure. 4. À l' - Maytag MET8775XB | Installation Instructions - Page 21
Installation de la bride antibasculement 1. Retirer la bride antibasculement située dans le four supérieur Montage au plancher avec l'ensemble de documents d'installation. 2. Déterminer la méthode de montage à utiliser : au plancher ou A B au mur. Pour un plancher en pierre ou en briquetage, - Maytag MET8775XB | Installation Instructions - Page 22
déformés. 8. Mettre l'appareil sous tension. Mettre en marche les éléments de surface et le four. Pour des instructions spécifiques concernant l'utilisation de la cuisinière, consulter le Guide d'utilisation et d'entretien. Si la cuisinière ne fonctionne pas, contrôler ce qui suit : ■ Les fusibles - Maytag MET8775XB | Installation Instructions - Page 23
cuisinière se trouve sous la bride antibasculement. Joindre de nouveau la bride antibasculement si la cuisinière est déplacée. Le non-respect de ces instructions peut causer un décès ou des brûlures graves aux enfants et aux adultes. Lorsqu'on déplace la cuisinière, la faire glisser sur une - Maytag MET8775XB | Installation Instructions - Page 24
W10289536A © 2010. All rights reserved. Tous droits réservés. 1/10 Printed in U.S.A. Imprimé aux É.-U.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
INSTALLATION INSTRUCTIONS
FREESTANDING ELECTRIC RANGE WITH DOUBLE OVENS
INSTRUCTIONS D'INSTALLATION POUR CUISINIÈRE
ÉLECTRIQUE AUTOPORTANTE AVEC FOURS DOUBLES
RANGE SAFETY
Table of Contents
Table des matières
RANGE SAFETY
.........................................................................
1
INSTALLATION REQUIREMENTS
............................................
2
Tools and Parts
........................................................................
2
Location Requirements
............................................................
2
Electrical Requirements - U.S.A. Only
.....................................
4
Electrical Requirements - Canada Only
..................................
5
INSTALLATION INSTRUCTIONS
..............................................
6
Unpack Range
.........................................................................
6
Adjust Leveling Legs
................................................................
6
Install Anti-Tip Bracket
.............................................................
7
Electrical Connection - U.S.A. Only
.........................................
8
Verify Anti-Tip Bracket Location
............................................
13
Level Range
...........................................................................
13
Complete Installation
.............................................................
13
Moving the Range
..................................................................
14
SÉCURITÉ DE LA CUISINIÈRE
..............................................
16
EXIGENCES D’INSTALLATION
..............................................
17
Outils et pièces
.....................................................................
17
Exigences d’emplacement
...................................................
17
Spécifications électriques – Canada seulement
..................
19
INSTRUCTIONS D'INSTALLATION
.......................................
20
Déballage de la cuisinière
.....................................................
20
Réglage des pieds de nivellement
........................................
20
Installation de la bride antibasculement
...............................
21
Vérification de l'emplacement de la
bride antibasculement
..........................................................
22
Réglage de l'aplomb de la cuisinière
....................................
22
Achever l’installation
.............................................................
22
Déplacement de la cuisinière
................................................
23
W10289536A
IMPORTANT:
Save for local electrical inspector's use.
IMPORTANT :
À conserver pour consultation par l'inspecteur local des installations électriques.
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING