Maytag MMV1164WS Installation Instructions
Maytag MMV1164WS Manual
 |
UPC - 883049206431
View all Maytag MMV1164WS manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MMV1164WS manual content summary:
- Maytag MMV1164WS | Installation Instructions - Page 1
Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in Rear Wall 7 Attach Mounting Plate to Wall 8 Prepare Upper Cabinet 8 Install Damper Assembly 9 Install the Microwave Oven 9 Complete Installation 10 VENTING DESIGN SPECIFICATIONS 11 ASSISTANCE 12 Replacement Parts 12 Accessories 12 MICROWAVE - Maytag MMV1164WS | Installation Instructions - Page 2
User Instructions.) NOTE: Depending on model, aluminum grease filter and charcoal filter may be combined. Materials needed ■ Standard fittings for wall or roof venting. See "Venting Design Specifications" section. Remove Cardboard Template The cardboard piece from the top of the microwave oven - Maytag MMV1164WS | Installation Instructions - Page 3
for 66" (167.6 cm) installation height. Exact dimensions may vary depending on type of range/cooktop below. Product Dimensions 17¹⁄₄" (43.8 cm) 16¹⁄₄" (41.3 cm) (411.06¹c⁄₈m") 29⁷⁄₈" (76.0 cm) GROUNDING INSTRUCTIONS ■ For all cord connected appliances: The microwave oven must be grounded. In - Maytag MMV1164WS | Installation Instructions - Page 4
180° so that exhaust ports face the back of microwave oven, and lower blower motor back into the microwave oven. Rotate Blower Motor The microwave oven is set for recirculation installation. For wall or roof venting, changes must be made to the venting system. NOTE: Skip this section if you are - Maytag MMV1164WS | Installation Instructions - Page 5
Step 1 from "Wall Venting Installation Only." 2. Repeat Step 2 from "Wall Venting Installation Only." 3. Repeat Step 3 from "Wall Venting Installation Only." 4. Repeat Step 4 from "Wall Venting Installation Only." 5. Rotate blower motor so that exhaust ports face the top of microwave oven, and flat - Maytag MMV1164WS | Installation Instructions - Page 6
studs exist within the cabinet opening, do not install the microwave oven. 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. See illustrations in "Possible Wall Stud Configurations." 2. Mark the center of each stud, and draw a plumb line down each stud center. See - Maytag MMV1164WS | Installation Instructions - Page 7
Rear Wall The microwave oven must be installed on a minimum of 1 wall and mark the wall with the dimensions described in Step 4. D A C B A. Rear wall B. Cardboard template hole locations. 7. Set the mounting plate aside. Wall Venting Installation Only Upper cabinet bottom ³⁄₈" (1 cm) 4" (10 - Maytag MMV1164WS | Installation Instructions - Page 8
secured to the wall on at least 1 wall stud as well as at both ends. 1. With the support tabs of the guides. ■ If the wall behind the microwave oven (as installed) has a partial wall covering (for example, tile backsplash), be sure the "Rear Wall" arrows align to the thickest part of the rear wall - Maytag MMV1164WS | Installation Instructions - Page 9
Cabinet Template. 8. Using a keyhole saw, cut out the rectangular area. Install Damper Assembly (for wall venting only) 1. Check that damper blade moves freely, and opens fully. 2. Position the damper assembly on the back of the microwave oven so that the damper blade hinge is at the top, and the - Maytag MMV1164WS | Installation Instructions - Page 10
cabinet bottom and the microwave oven. A 2. Connect vent to damper assembly. A B A. Vent B. Damper assembly (under vent) Complete Installation 1. Install filters. Refer to the User Instructions for filter placement. WARNING A. Bolts For Roof Venting Installation Only 1. Insert damper assembly - Maytag MMV1164WS | Installation Instructions - Page 11
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood combination. ■ We do not recommend using a flexible metal vent. ■ To avoid possible product - Maytag MMV1164WS | Installation Instructions - Page 12
Replacement Parts If any of the installation hardware needs to be replaced, call us at our toll free number listed in the User Instructions. Following is a list of available replacement parts. You will need your model number located on the front facing of the microwave oven opening, behind the door
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
..............................
1
INSTALLATION REQUIREMENTS
...................................................
2
Tools and Parts
...............................................................................
2
Remove Cardboard Template
........................................................
2
Location Requirements
...................................................................
2
Product Dimensions
.......................................................................
3
Electrical Requirements
..................................................................
3
INSTALLATION INSTRUCTIONS
.....................................................
4
Remove Mounting Plate
.................................................................
4
Rotate Blower Motor
.......................................................................
4
Locate Wall Stud(s)
.........................................................................
6
Mark Rear Wall
................................................................................
7
Drill Holes in Rear Wall
....................................................................
7
Attach Mounting Plate to Wall
........................................................
8
Prepare Upper Cabinet
...................................................................
8
Install Damper Assembly
................................................................
9
Install the Microwave Oven
............................................................
9
Complete Installation
....................................................................
10
VENTING DESIGN SPECIFICATIONS
............................................
11
ASSISTANCE
...................................................................................
12
Replacement Parts
.......................................................................
12
Accessories
...................................................................................
12
W10344702A
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING