Maytag MMV5220FB Installation Guide
Maytag MMV5220FB Manual
 |
View all Maytag MMV5220FB manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MMV5220FB manual content summary:
- Maytag MMV5220FB | Installation Guide - Page 1
very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety if you don't immediately follow instructions. WARNING You can be killed or seriously injured if you don't follow instructions. All safety messages will tell - Maytag MMV5220FB | Installation Guide - Page 2
minimum 3/8" (10 mm) thickness drywall or plaster/lath within cabinet opening. ■■ Support for weight of 150 lbs (68 kg), which includes microwave oven and items placed model, charcoal filters may not be included. See User Instructions.) NOTE: Depending on model, aluminum grease filter and charcoal - Maytag MMV5220FB | Installation Guide - Page 3
a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A. 2" x 4" wall stud B. Grounded 3 prong outlet *30" (76.2 cm) is typical for 66" (167.6 cm) installation - Maytag MMV5220FB | Installation Guide - Page 4
INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of - Maytag MMV5220FB | Installation Guide - Page 5
6. Using diagonal wire cutting pliers, gently snip out the rectangular damper vent covers at the perforations. Roof Venting Installation Only 1. Repeat steps 1 to 4 from "Wall Venting Installation Only." 2. Rotate blower motor so that exhaust ports face the top of microwave oven and flat sides of - Maytag MMV5220FB | Installation Guide - Page 6
Hole Figure 3 Wall Studs at Both End Holes Figure 4 B D B A A,D A,D A,D E E E E C C C C F F A. End holes (on mounting plate) B. Cabinet opening vertical centerline C. Wall stud centerlines D. Holes for lag screws E. Support tabs F. Mounting plate center markers 6 - Maytag MMV5220FB | Installation Guide - Page 7
the upper cabinet and must be on a level line with each other. They must each be 141/8" (35.9 cm) from the centerline. 5. With the support tabs facing forward (see illustrations in "Locate Wall Stud(s)" section), align the mounting plate center markers to the centerline on the wall, making sure its - Maytag MMV5220FB | Installation Guide - Page 8
on at least 1 wall stud as well as at both ends. 1. With the support tabs of the mounting plate facing forward, insert 3/16-24 x 3" round-head bolts , against the upper cabinet bottom. The template has trim lines to use as guides. ■■ If the wall behind the microwave oven (as installed) has a partial - Maytag MMV5220FB | Installation Guide - Page 9
shut. 3. Using 2 or more people, lift microwave oven and hang it on support tabs at the bottom of mounting plate. NOTE: To avoid damage to the microwave assembly with 2 sheet metal screws. A B A. Mounting plate B. Support tabs 4. With front of microwave oven still tilted, thread power supply - Maytag MMV5220FB | Installation Guide - Page 10
has not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. ■■ Check that the power supply cord is plugged into a grounded 3 prong outlet. ■■ See the User Instructions for troubleshooting information. Installation is now complete. Save Installation - Maytag MMV5220FB | Installation Guide - Page 11
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■■ Vent materials needed for installation are not provided with microwave hood combination. Rectangular to Round Transition: NOTE: The minimum 3" (7.6 cm) clearance must - Maytag MMV5220FB | Installation Guide - Page 12
to keep the damper from sticking. ASSISTANCE Call your authorized dealer or service center. When you call, you will need the microwave oven model number our toll free number or visit our website listed in the User Guide. Replacement Parts If any of the installation hardware needs to be replaced, call
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration
in these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
MICROWAVE HOOD COMBINATION SAFETY
.........................................
1
INSTALLATION REQUIREMENTS
..............................................................
2
Tools and Parts
.........................................................................................
2
Location Requirements
............................................................................
2
Product Dimensions
.................................................................................
3
Electrical Requirements
............................................................................
3
INSTALLATION INSTRUCTIONS
................................................................
4
Remove Mounting Plate
...........................................................................
4
Rotate Blower Motor
................................................................................
4
Locate Wall Stud(s)
...................................................................................
6
Mark Rear Wall
..........................................................................................
7
Drill Holes in Rear Wall
..............................................................................
7
Attach Mounting Plate to Wall
..................................................................
8
Prepare Upper Cabinet
.............................................................................
8
Install Damper Assembly
..........................................................................
9
Install the Microwave Oven
......................................................................
9
Complete Installation
..............................................................................
10
VENTING DESIGN SPECIFICATIONS
......................................................
11
ASSISTANCE
.............................................................................................
12
Replacement Parts
.................................................................................
12
Accessories
.............................................................................................
12
W10823835A