NEC 4650N Quick Start Guide

Instructions Continued

On Reverse Side

PRINTING A STARTUP PAGE

1.

Connect the Power

Cord to the back of

the printer.

2.

Turn on the Power button located on the

lower left front corner of the printer.

3.

Indicator lights cycle

and messages

appear on the

Operator Panel.

Power

Warning

Online

Menu

OnLine

Data

OHT

Label

Feed

Item

Media

Previous

Next

Select

4.

A Startup Page

prints and

READY

appears on the

Operator Panel.

For sales information, call (800) NEC-INFO or visit our website at http://www.nectech.com.

For supplies, call (800) 632-2326

GENERAL INFO

STORAGE

JOB OPTIONS

ENGINE INFO

PARALLEL PORT

NETWORK PORT

Printer Name: SuperScript 4650N

Software Version: 0.04

Build Time: 936928632

PostScript Version: 3010.108

PrintAgent Version: 1.008

Disk Resource Version: 0.0.4N

Number of Copies: 1

Print PS Errors: Enabled

Wait Timeout: 240 seconds

Job Timeout: Never

RAM Installed: 128 Megabytes

Disk Size: 1964.03 Megabytes

Disk Free: 1667.97 Megabytes

Default Resolution: 600.0 X 600.0 DPI

Edge Smoothing: Disabled

Jam Recovery: Enabled

Tray 1: Letter

Tray 2: Legal

Pages Printed: 2182

Status: Enabled

Bi-di: Enabled

Personality: AutoSelect

Status: Enabled

Personality: AutoSelect

Web Address: http://131.241.45.88

LOADING LETTER PAPER

1.

Remove Paper Tray 1.

2.

Squeeze on both sides of the length tab

and slide it into place. The outside of the

tab should match letter size (LTR) marked

on the inside of the tray.

3.

Squeeze the left side guide and

slide it to match your paper’s

width. The inside of the tab

should match the desired size

on the tray.

4.

Fill the paper tray.

Do not overfill paper tray!

NOTE:

Load and print only regular paper

(16 to 24 lb.) until you read Chapter 2 of

your User's Guide. Other media must be

selected on the Operator Panel.

INSTALLING THE TONER MODULES

2.

Begin with the Cyan Toner Module.

R

emove from its plastic bag and rock

gently three or four times.

R

emove the tape from the Module.

R

emove (but

save) the packing

face plate.

5.

Close the Front Cover.

4.

Repeat steps 2 and 3 for the remaining

Toner Modules.

3.

Hold the module level and slide into

place along the racks in the printer.

1.

The color labels inside the front of the

printer indicate where to place each of

the color Toner Modules.

IMPORTANT!

If you need to move the printer once the

accessories are installed, please see Appendix D of the

SuperScript 4650 Series User’s Guide

, “Moving Your

Printer.”

INSTALLING THE FUSER OIL BOTTLE & CLEANING ROLLER

1.

P ush the Fuser Roller Release

Tabs backward and pull out the

orange Tension Release Pins.

4.

R emove the Fuser Cleaning

Roller from its plastic bag. Place

in printer top with the exposed

part of the roller facing the

front.

6.

Close the Top

Cover of the

printer.

5.

T urn the Lock Tabs to the locked

position.

3.

R emove the Fuser Oil Bottle

from its plastic bag and set into

place with the shunt valve down

and the labeled side facing the

front.

2.

Mak

e sure the Lock Tabs are in

the open position.

WARNING!

Damage to internal parts may

result if fuser oil accidently spills inside the

printer.

Keep printer level at all times.

INSTALLING THE BELT CARTRIDGE

1.

Open the F ront Cover using the

Front Cover Release Latch.

2.

Open the Top Cover by sliding

the Top Cover Release Button

forward.

3.

Flip up the Belt Car tridge

Locking Levers inside the top of

the printer.

4.

R

emove the Tension Release

Pins and the black protective

sheet from the Belt Cartridge.

Be careful not to scratch the

shiny green surface.

5.

Slide the Belt Car tridge into the

guides.

Do not force it!

The flat side

of the Belt

Cartridge

faces front.

6.

Flip down the Belt Car tridge

Locking Levers.

ADDING THE PAPER TRAY 2 UNIT (4650NX ONLY)

1.

R emove the Paper Tray 2 Unit from its

packaging.

NOTE:

Paper Tray 2

will increase the

printer’s height by

4 inches.

3.

S et the Paper Tray 2 Unit next to the

printer. Carefully align the Paper Tray 2

Unit to the printer.

K

eeping the printer

level, have two

people lift the printer

up and onto the

Paper Tray 2 Unit.

4.

L ocate the metal tab with screw hole on

each side of the Paper Tray 2 Unit.

Take a metal bracket

from the packet and

hold it at a slight

angle away from

you. Slide the bracket

up into the hole

beneath the printer.

5.

Carefully align the hole in eac h metal

bracket with the corresponding screw

hole on the Paper

Tray 2 Unit. Insert

and tighten the

thumb screws.

6.

F acing the back of

the printer, locate

the Connector

Cable at the rear of

the Paper Tray 2

Unit. Make sure

the cable is

extending past the

7.

R emove the Cable

Connector Doors from

both the printer and the

Paper Tray 2 Unit. Set the

doors aside.

8.

Plug the P aper Tray 2 unit

Connector Cable into the

printer socket.

9.

S witch the two Cable

Connector Doors. Place

the small door on the

printer and the large

door on the Paper Tray 2

Unit.

10.

Snap on the

left and right

Paper Tray 2

Unit covers.

Connector Cable

Screw Hole

2.

L ocate the packet of brackets and thumb

screws and set aside. Extend the

Connector Cable away from the unit.

VERIFYING THE

BOX CONTENTS

Belt Cartridge

1 Black Toner Module

1 Cyan Toner Module

1 Magenta Toner Module

1 Yellow Toner Module

Fuser Oil Syringe

(save for future use)

Fuser Oil Bottle

Fuser Cleaning Roller

Accessory Kit

Starter Kit

•

NEC Paper Sample Pack

•

Software Envelope

•

SuperScript 4650 Series CD

•

SuperScript 4650 Series User's Guide

•

SuperScript Color Laser Network

Guide (4650N or 4650NX only)

To connect your printer, you need to

provide the proper parallel and/or

network cable.

Not included …

Category 5 Twisted Pair Cable

with RJ-45 Connectors for

10/100Base-T Ethernet

IEEE 1284

Bidirectional Parallel Cable

Includes a standard 250-sheet

Paper Tray 1 and a power cord.

4650 Series Printer

(Additional 250-sheet paper tray

included only with the 4650NX)

Paper Tray 2 Unit

UNPACKING THE

PRINTER

1.

Open the top of the packing box.

R

emove the Accessory kit and the

Starter kit.

2.

T urn the large plastic box screws at the bottom of the

box to the left (A) and pull out to remove (B).

Using your thumb and finger

, remove the plastic

screw sleeves from the box (C).

3.

Lif t off the outer box. Open the

plastic bag that contains the

printer and slide it down. Do not

attempt to lift the printer by its

plastic bag!

A

B

C

4.

With one per son on each side of the printer, grasp the

printer at the hand grips where they are exposed by

notches in the foam padding. Place on a sturdy level

desk or table.

The printer and packaging

weighs approximately 100

lbs. To set up the printer and

move it requires two adults.

IMPORTANT!

Pick the location for your

printer carefully. Make sure it has good

ventilation and that the surface is level. For

more information see Chapter 2 of the

SuperScript 4650 Series User's Guide

.

QUICKSTART

4650 4650N 4650NX

NEC0

NEC 4650N Quick Start Guide

NEC 4650N - SuperScript Color Laser Printer Manual

NEC 4650N manual content summary: