NEC NP-P452H Users Manual

NEC NP-P452H Manual

Get NEC NP-P452H PDF manuals and user guides View all NEC NP-P452H manuals
Add to My Manuals
Save this manual to your list of manuals

NEC NP-P452H manual content summary:

  • NEC NP-P452H | Users Manual - Page 1
    Projector P502H/P452H P502W/P452W User's Manual Model No. NP-P502H, NP-P452H, NP-P502W, NP-P452W
  • NEC NP-P452H | Users Manual - Page 2
    . • App Store is a service mark of Apple Inc. • manual pdf" inside the "about GPL&LGPL" folder on the supplied CDROM. NOTES (1) The contents of this user's manual manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), NEC
  • NEC NP-P452H | Users Manual - Page 3
    this manual carefully before using your NEC projector and keep the manual handy ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the provided. The information should be read carefully to avoid problems. WARNING: TO PREVENT FIRE OR SHOCK, DO NOT
  • NEC NP-P452H | Users Manual - Page 4
    specified by NEC Display Solutions of America, Inc. in this manual. Failure to Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire , the ceiling must be strong enough to support the projector and the installation must be in accordance with
  • NEC NP-P452H | Users Manual - Page 5
    objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel. • Do not place any objects on top of the projector. • Do not touch the power plug during a thunderstorm
  • NEC NP-P452H | Users Manual - Page 6
    instructions described in this user's manual. - If the projector has been dropped or the cabinet has been damaged. - If the projector exhibits a distinct change in performance, indicating a need for service authority law. FOR MORE INFORMATION, CONTACT: NEC Display Solutions of America, Inc. 500 Part
  • NEC NP-P452H | Users Manual - Page 7
    specified lamp for safety and performance. • To replace the lamp, follow all instructions provided on page 118. • Be sure to replace the lamp when the About Copyright of original projected pictures: Please note that using this projector for the purpose of commercial gain or the attraction of public
  • NEC NP-P452H | Users Manual - Page 8
    ) 2. AUTO POWER OFF (Factory preset: 60 min.) To control the projector from an external device, select [OFF] for [AUTO POWER OFF]. NOTE care precautions that may be found in the user's manual included with your LCD shutter eyeglasses or your 3D compatible nec-display.com/global/support/index.html vi
  • NEC NP-P452H | Users Manual - Page 9
    Information i 1. Introduction...1 ❶ What's in the Box?...1 ❷ Introduction to the Projector 2 General...2 Installation...2 Videos...2 Network...2 Energy-saving...3 About this user's manual 3 ❸ Part Names of the Projector 4 Front...4 Mounting the lens cap strap 4 Rear...5 Controls/Indicators
  • NEC NP-P452H | Users Manual - Page 10
    [SECURITY 30 ❻ Viewing 3D Images...33 LCD shutter eyeglasses (recommended 33 Steps for viewing 3D images on the projector 33 Troubleshooting on viewing 3D images 36 4. Using On-Screen Menu 37 ❶ Using the Menus...37 Menu Elements...38 ❷ List of Menu Items...39 ❸ Menu Descriptions & Functions
  • NEC NP-P452H | Users Manual - Page 11
    Included on CD-ROM 92 ❷ Projecting Your Computer's Screen Image from the Projector over a LAN (Image Express Utility Lite 93 Starting Image Express Utility Lite the Filters 118 9. Appendix...125 ❶ Troubleshooting...125 Indicator Messages 125 Common Problems & Solutions 127 If there is no
  • NEC NP-P452H | Users Manual - Page 12
    Information (For North America: 7N8N6521) (For Other countries than North America: 7N8N6521 and 7N8N6531) • Quick Setup Guide (7N8N6541)/ (7N8N6551) NEC Projector CD-ROM User's manual (PDF) and the utility software (7N952321) For North America only Limited warranty For customers in Europe: You
  • NEC NP-P452H | Users Manual - Page 13
    P502W/P452W 0.65 type 1280 × 800 pixels Aspect ratio 16:9 16:10 • Lamp life up to 5000 hours Using in Eco Mode allows you to prolong the projector stored in the enclosed NEC Projector CD-ROM (Image Express • CRESTRON ROOMVIEW compatible This projector supports CRESTRON ROOMVIEW, allowing multiple
  • NEC NP-P452H | Users Manual - Page 14
    condition with energy saving technology Selecting [NORMAL] for [STANDBY MODE] from the menu can put the projector in power-saving mode. NORMAL: 0.26 W (100-130 V AC)/0.33 W (200-240 V on the on-screen menu (CARBON METER). About this user's manual The fastest way to get started is to take your time
  • NEC NP-P452H | Users Manual - Page 15
    ❸ Part Names of the Projector Front Lens shift dials (Horizontal/Vertical) (→ page 17) Zoom Lever (→ page 19 page 83) Exhaust Vent Model name Model name is indicated on the bottom face of the projector Tilt Foot (→ page 20) Lens cap mount hole 2. Insert the knot into the strap mount hole (large)
  • NEC NP-P452H | Users Manual - Page 16
    . The security chain opening accepts security wires or chains up to 0.18 inch/4.6 mm in diameter. Intake Vent Filter (→ page 113, 123) * This security slot supports the MicroSaver® Security System. 5
  • NEC NP-P452H | Users Manual - Page 17
    Controls/Indicators 2 34 5 6 8 9 1. (POWER) Button (→ page 12, 24) 2. POWER Indicator (→ page 11, 12, 24, 125) 3. STATUS Indicator (→ page 125) 4. LAMP Indicator (→ page 125) 5. ECO Button (→ page 28) 6. SOURCE Button (→ page 14) 7. AUTO ADJ. Button (→ page 23) 8. MENU Button (→ page 37) 9
  • NEC NP-P452H | Users Manual - Page 18
    SERVICE Port (USB Type B) (for service purpose only) 16. REMOTE Connector (Stereo Mini) Use this connector for wired remote control of the projector using the NEC REMOTE SENSOR] and the projector is connected to a commercially-available transmission device that supports HDBaseT, remote control
  • NEC NP-P452H | Users Manual - Page 19
    page 48) 13. USB-B Button 32. FOCUS/ZOOM Button (This button does not work in this (This button does not work in this series of projectors) series of projectors) 14. APPS Button (→ page 14, 88) 33. HELP Button (→ page 66) 15. ID SET Button (→ page 57) 16. Numeric Keypad Button/ CLEAR Button
  • NEC NP-P452H | Users Manual - Page 20
    signal operates by line-of-sight up to a distance of about 23 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet. • The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries
  • NEC NP-P452H | Users Manual - Page 21
    onto the screen. ❶ Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 11) Step 2 • Turning on the projector (→ page 12) Step 3 • Selecting a source (→ page 14) Step 4 • Adjusting the picture size and position (→ page 16) • Correcting keystone distortion
  • NEC NP-P452H | Users Manual - Page 22
    connection to a computer. For information about other connections, see "5. Installation and Connections" on page 69. Connect the computer cable (VGA) between the projector's COMPUTER IN terminal and the computer's port (mini D-Sub 15 Pin). Turn two thumb screws of both terminals to fix the computer
  • NEC NP-P452H | Users Manual - Page 23
    (Basic Operation) 1. Remove the lens cap. With the lens cap's stopper pressed up, pull forward and off. Stopper 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator lights blue and the image is projected on the screen. TIP: • When
  • NEC NP-P452H | Users Manual - Page 24
    Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity on page 39 and 52) NOTE: • Keep the lens cap off the lens while the projector's power is on. If the lens cap is on, it could be warped due to high
  • NEC NP-P452H | Users Manual - Page 25
    Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once. The projector will search for the available input source and display it. The input source will change as follows
  • NEC NP-P452H | Users Manual - Page 26
    2. Projecting an Image (Basic Operation) Selecting Default Source You can so that it will be displayed each time the projector is turned on. 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button twice to select [SETUP] and the ▼ button or the ENTER
  • NEC NP-P452H | Users Manual - Page 27
    2. Projecting an Image (Basic Operation) ❺ Adjusting the Picture Size and Position Use the lens shift dial, the adjustable tilt foot lever, the zoom lever/zoom ring and the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the
  • NEC NP-P452H | Users Manual - Page 28
    Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) CAUTION Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them. 1. Turn the lens shift dials clockwise or
  • NEC NP-P452H | Users Manual - Page 29
    the lens shift adjustment range regarding the [CEILING FRONT] projection, see page 73. [P502H/P452H] 25%H 25%H Width of projected image 62%V [P502W/P452W] 100%V 25%H 100%H 25%H 59%V 28%H 28%H Height of projected image Width of projected image 100%V Height of projected image 28%H 100
  • NEC NP-P452H | Users Manual - Page 30
    the FOCUS ring to obtain the best focus. 2. Projecting an Image (Basic Operation) NOTE: • Recommend to perform the focus adjustment after leaving the projector under the state the TEST PATTERN has been projected for over 30 minutes. Please refer page 58 about the TEST PATTERN. Focus ring Zoom
  • NEC NP-P452H | Users Manual - Page 31
    Keystone Distortion [KEYSTONE]" (→ page 21). • The tilt feet can be lengthened by a maximum of 18 mm. • The tilt feet can be used to tilt the projector by a maximum of 4°. Up Down Tilt foot NOTE: • Do not use the tilt feet for any purpose other than adjusting the
  • NEC NP-P452H | Users Manual - Page 32
    of the projected image are parallel. 1. When APPS is not selected as source and the menu is not displayed on, press the ▼ button on the projector cabinet. The Keystone screen will be displayed on the screen. • Press the KEYSTONE button when using the remote control. • See page 22 for [RESET
  • NEC NP-P452H | Users Manual - Page 33
    2. Projecting an Image (Basic Operation) 4. Press the ▲ button to select [HORIZONTAL] and then use the ◀ or ▶ so that the top and bottom sides of the projected image are parallel. • Adjust the horizontal keystone distortion. 5. Repeat steps 2 and 4 to correct keystone distortion. 6. After completing
  • NEC NP-P452H | Users Manual - Page 34
    signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE] manually. (→ page 46, 47) ❽ Turning Up or Down Volume Sound level from be adjusted. TIP: When no menus appear, the ◀ and ▶ buttons on the projector cabinet work as a volume control. NOTE: • Volume control is not available with
  • NEC NP-P452H | Users Manual - Page 35
    or press the (POWER) or the STANDBY button again. The lamp and the power are turned off and the cooling fan stops to rotate, the projector goes into the STANDBY MODE. When in standby mode, the POWER indicator will light red and the STATUS indicator will turn off when [NORMAL] is
  • NEC NP-P452H | Users Manual - Page 36
    ❿ When Moving the Projector Preparation: Make sure that the projector is turned off. 2. Projecting an Image (Basic Operation) 1. If the separately sold cable cover is mounted, remove it. (→ page 132) 2. Unplug the power cord. 3. Disconnect
  • NEC NP-P452H | Users Manual - Page 37
    3. Convenient Features ❶ Turning off the Image and Sound Press the AV-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. NOTE: • Even though the image is turned off, the menu still remains on the screen. ❷ Freezing a Picture Press the
  • NEC NP-P452H | Users Manual - Page 38
    ❸ Magnifying a Picture You can enlarge the picture up to four times. NOTE: • The maximum magnification may be less than four times depending on the signal. To do so: 1. Press the D-ZOOM (+) button to magnify the picture. To move the magnified image, use the or ▶ button. 3. Convenient Features 2.
  • NEC NP-P452H | Users Manual - Page 39
    MODE and DYNAMIC CONTRAST. • Immediately after the menu item is selected for [ECO MODE], the screen may flicker. This is not malfunction. • Using the projector in the [AUTO ECO], [NORMAL], or [ECO] mode for [ECO MODE] may cause poor halftones depending on the projected image. • When [ECO] has been
  • NEC NP-P452H | Users Manual - Page 40
    Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector's [ECO MODE] is set. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The
  • NEC NP-P452H | Users Manual - Page 41
    using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image. • The [SECURITY] setting cannot be cancelled by using the [RESET] of the
  • NEC NP-P452H | Users Manual - Page 42
    the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button. The projector will be turned on and display a message to the effect that the projector is locked. 2. Press the MENU button. 3. Type in the correct keyword and
  • NEC NP-P452H | Users Manual - Page 43
    To disable the SECURITY function: 3. Convenient Features 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen
  • NEC NP-P452H | Users Manual - Page 44
    3D images" on the following page. 3. Play your 3D compatible content and use the projector to display the image. 4. Put on your LCD shutter eyeglasses to view 3D images. Also refer to the user's manual accompanied with your LCD shutter eyeglasses for more information. On-screen menu for 3D images
  • NEC NP-P452H | Users Manual - Page 45
    3D images [HDMI1/HDMI2/COMPUTER/VIDEO/ HDBaseT] This function switches the 3D mode between ON and OFF for each input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make sure that [3D] is displayed in the top right of the screen after the
  • NEC NP-P452H | Users Manual - Page 46
    emitter Xpand AD025-RF-X1 Connect your 3D emitter to the 3D SYNC terminal of the projector. NOTE: • Use an active shutter 3D eyewear (compliance with VESA) • Check the operating conditions described in the user manual of the Blu-ray player. • Please connect the DIN terminal of the 3D emitter to the
  • NEC NP-P452H | Users Manual - Page 47
    3. Convenient Features Troubleshooting on viewing 3D images If images will not be displayed in 3D or 3D images appear as 2D, check the following table. Also refer to the user's manual accompanied with your 3D content or LCD shutter eyeglasses. Possible causes Solutions • The content you are
  • NEC NP-P452H | Users Manual - Page 48
    display the submenu window. 6. Adjust the level or turn the selected item on or off by using the buttons on the remote control or the projector cabinet. Changes are stored until adjusted again. 7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the
  • NEC NP-P452H | Users Manual - Page 49
    of adjustment. ECO mode symbol Indicates ECO MODE is set. Key Lock symbol Indicates the [CONTROL PANEL LOCK] is enabled. Thermometer symbol Indicates the projector is in the state of the [FORCED ECO MODE]. High Altitude symbol Indicates the [FAN MODE] is set to [HIGH ALTITUDE] mode. Wireless
  • NEC NP-P452H | Users Manual - Page 50
    4. Using On-Screen Menu ❷ List of Menu Items Some menu items are not available depending on the input source. The below listed menu items are on the advanced menu. The mark (B) is added to the items on the basic menu. Refer to 88 pages about the APPS MENU. Menu Item SOURCE ADJUST SETUP HDMI1
  • NEC NP-P452H | Users Manual - Page 51
    FORMAT L/R INVERT 3D L/R INVERT 3D GLASSES FORMAT L/R INVERT Default Options COLOR COLOR, MONOCHROME ON OFF, ON ON OFF, ON OFF OFF, ON AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC BLUE BLUE, BLACK, LOGO ON OFF, ON OFF OFF, 100H, 500H, 1000H, 2000H DESKTOP DESKTOP FRONT
  • NEC NP-P452H | Users Manual - Page 52
    (1) (B) FIRMWARE DATA VERSION(2) (B) FIRMWARE2 OTHERS (B) PROJECTOR NAME HOST NAME MODEL NO. SERIAL NUMBER LAN UNIT PAL60, SECAM 8[bits], 10[bits], 12[bits] FULL, ENHANCED, DEFAULT SUPPORTED, NOT SUPPORTED NORMAL, WARNING, ABNORMAL HDBaseT, ETHERNET, LOW POWER, DISCONNECT NO LINK, HDBaseT
  • NEC NP-P452H | Users Manual - Page 53
    , select [COMPUTER]. VIDEO Selects what is connected to your VIDEO input-VCR, DVD player or document camera. HDBaseT Projects the signal transmitted from the terminals supported HDBaseT. (→ page 86) APPS Display the APPS MENU or the function in the APPS MENU that was used last time. 42
  • NEC NP-P452H | Users Manual - Page 54
    4. Using On-Screen Menu ❹ Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are eight factory presets optimized for various types of images. You can
  • NEC NP-P452H | Users Manual - Page 55
    [DETAIL SETTINGS] 4. Using On-Screen Menu Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 8]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT
  • NEC NP-P452H | Users Manual - Page 56
    [CONTRAST] Adjusts the intensity of the image according to the incoming signal. 4. Using On-Screen Menu [BRIGHTNESS] Adjusts the brightness level or the back raster intensity. [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies
  • NEC NP-P452H | Users Manual - Page 57
    [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. 4. Using On-Screen Menu CLOCK Use this item to fine tune the computer image or to remove any vertical banding that
  • NEC NP-P452H | Users Manual - Page 58
    Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. 4. Using On-Screen Menu - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and
  • NEC NP-P452H | Users Manual - Page 59
    the ratio of width to height of a projected image. The projector automatically determines the incoming signal and displays it in its appropriate ratio. • This table shows typical resolutions and aspect ratios that most computers support. Resolution VGA 640 × 480 SVGA 800 × 600 XGA 1024 × 768
  • NEC NP-P452H | Users Manual - Page 60
    Sample image when the appropriate aspect ratio is automatically determined P502W/P452W [Video signal] Aspect ratio of incoming signal 4:3 ] This function allows you to select the level of noise reduction. The projector is set to the optimized level for each signal at the factory. Select
  • NEC NP-P452H | Users Manual - Page 61
    SETUP] [GENERAL] Correcting Keystone Distortion Manually [KEYSTONE] You can correct horizontal or vertical keystone manually. [HORIZONTAL] and [VERTICAL] values will be overwritten. They will not be deleted even when the projector is turned off. • Using [KEYSTONE] correction can cause the image to
  • NEC NP-P452H | Users Manual - Page 62
    Using the Wall Color Correction [WALL COLOR] 4. Using On-Screen Menu This function allows for quick adaptive color correction in applications where the screen material is not white. Setting various items related to lamp brightness [ECO SETTINGS] This option allows you to decrease the power
  • NEC NP-P452H | Users Manual - Page 63
    projector does not support PROJECTOR WILL TURN OFF WITHIN 3 MINUTES] message will be displayed on the bottom of the screen. Display the tools menu [TOOLS] This function display the tools menu. (→ page 91) Selecting Menu Language [LANGUAGE] You can choose one of 30 languages for on-screen instructions
  • NEC NP-P452H | Users Manual - Page 64
    EXIT button. Selecting Menu Display Time [DISPLAY TIME] This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the factory preset
  • NEC NP-P452H | Users Manual - Page 65
    4. Using On-Screen Menu Selecting a Color or Logo for Background [BACKGROUND] Use this feature to display a blue/black screen or logo when no signal is available. The default background is [BLUE]. NOTE: • When [SOURCE DISPLAY] is turned on, the no-signal guidance prompting you to check for an
  • NEC NP-P452H | Users Manual - Page 66
    10 seconds. The CONTROL PANEL LOCK will be released. 2. When the projector is in the standby mode, press and hold the POWER button on the projector cabinet. It enables to power on the projector. After checking the projector is projecting image, perform the previous step 1. TIP: When the [CONTROL
  • NEC NP-P452H | Users Manual - Page 67
    sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The default is 38400 bps. On or Off Remote Sensor [REMOTE SENSOR] Set the remote control sensors on the projector's front and rear panels and the HDBaseT remote control sensor. The options are: ALL
  • NEC NP-P452H | Users Manual - Page 68
    the CONTROL ID setting. NOTE: • When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the CONTROL ID function. (In this case the buttons on the projector cabinet can be used.) • Your setting will not be affected even when [RESET
  • NEC NP-P452H | Users Manual - Page 69
    -Screen Menu Using Test Pattern [TEST PATTERN] Displays the test pattern for adjusting distortion on the screen and the focus at the time of the projector setup. Once the [TEST PATTERN] on the onscreen menu is selected, the pattern for adjustment will be displayed on. If you find distortion on the
  • NEC NP-P452H | Users Manual - Page 70
    . HIGH The built-in fans run at a high speed. HIGH ALTITUDE The built-in fans run at a high speed. Select this option when using the projector at altitudes approximately 4000 feet/1200 meters or higher. NOTE: • It is recommended that you select High speed mode if you use the
  • NEC NP-P452H | Users Manual - Page 71
    4. Using On-Screen Menu Setting HDMI1, HDMI2, or HDBaseT [HDMI SETTINGS] Make the settings for each video level when connecting HDMI equipment and Ethernet/HDBaseT terminal. VIDEO LEVEL Select [AUTO] to automatically detect video level. If automatic detection may not work well, select [NORMAL] to
  • NEC NP-P452H | Users Manual - Page 72
    following buttons, terminals, and features will work: POWER buttons on the projector cabinet and the remote control, powering on from PC Control command, AUTO POWER ON, Operation by User Supportware, Network service, Program Timer. Important: • When [NETWORK STANDBY] is selected, [AUTO POWER OFF
  • NEC NP-P452H | Users Manual - Page 73
    is in Standby mode, applying a computer or HDMI signal from a computer connected to the COMPUTER IN input, HDMI1, or HDMI2 input will power on the projector and simultaneously project the image. This functionality eliminates the need to always use the POWER button on the remote control or the
  • NEC NP-P452H | Users Manual - Page 74
    is turned on. VIDEO Displays the Video source from the VIDEO IN terminal every time the projector is turned on. HDBaseT Projects the signal transmitted from the terminals supported HDBaseT. APPS Display the APPS MENU. NOTE: • [APPS] can not be detected when [AUTO] is selected. For projecting
  • NEC NP-P452H | Users Manual - Page 75
    the 3D mode for the selected input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make right eye images displayed horizontally. Only the half of the horizontal resolution is supported TOP AND BOTTOM Selects this format for the TOP AND BOTTOM 3D image
  • NEC NP-P452H | Users Manual - Page 76
    [L/R INVERT] Change the setting if you have difficulty seeing 3D images. 4. Using On-Screen Menu NON-INVERT Normal setting. INVERT Changes the order of displaying the images for left eye and right eye. NOTE: • When [L/R INVERT] cannot be operated, the [L/R INVERT] screen will not be displayed
  • NEC NP-P452H | Users Manual - Page 77
    time reaches 0, the LAMP LIFE REMAINING bar indicator changes from 0% to 100 Hours and starts counting down. If the remaining lamp time reaches 0 hours, the projector will not turn on. • The message to the effect that the lamp should be replaced will be displayed for one minute when the
  • NEC NP-P452H | Users Manual - Page 78
    ADDRESS] [GATEWAY] [WIRELESS LAN] [IP ADDRESS] [GATEWAY] [SSID] [SECURITY] [SIGNAL LEVEL] [VERSION(1)] [FIRMWARE] Version [VERSION(2)] [FIRMWARE2] Version [OTHERS] [PROJECTOR NAME] [MODEL NO.] [LAN UNIT TYPE] 4. Using On-Screen Menu [HORIZONTAL FREQUENCY] [SYNC TYPE] [SCAN TYPE] [VIDEO TYPE] [VIDEO
  • NEC NP-P452H | Users Manual - Page 79
    CONVERT], [LAMP LIFE REMAINING], [LAMP HOURS USED], [FILTER HOURS USED], [TOTAL CARBON SAVINGS], [PROJECTOR NAME], [WIRED LAN], [WIRELESS LAN], [IMAGE EXPRESS UTILITY LITE], [NETWORK SERVICE], [DATE & TIME], [ADMINISTRATOR MODE], and [REMOTE DESKTOP CONNECTION]. Clearing Lamp Hour Meter [CLEAR
  • NEC NP-P452H | Users Manual - Page 80
    wide images on a 150 screen, install at about 4.1 m from the front. Also, from the lower table we can see that about 2.1 m are required from the projector's lens center to the upper edge of the screen. Use this to see whether or not enough height can be provided from the
  • NEC NP-P452H | Users Manual - Page 81
    [P502W/P452W] 5. Installation and Connections Screen size (inch) 300 240 When zoom from the front. Also, from the lower table we can see that about 2.1 m are required from the projector's lens center to the upper edge of the screen. Use this to see whether or not enough height can be provided
  • NEC NP-P452H | Users Manual - Page 82
    height (inches) (cm) 15 37.4 20 49.8 25 62.3 29 74.7 39 99.6 49 124.5 59 149.4 74 186.8 98 249.1 123 311.3 147 373.6 [P502W/P452W] Screen height Screen size (diagonal) Screen width Size (inches) 30 40 50 60 80 100 120 150 200 250 300 Screen width (inches) (cm
  • NEC NP-P452H | Users Manual - Page 83
    diagram below shows an example of when the projector is used on a desktop. Horizontal projection position 28.9 −61.3 - +14.3 −155.7 - +36.2 −73.5 - +17.1 −186.8 - +43.4 [P502W/P452W] Lens center Approximately 81 to 86 mm Projection distance L Screen surface Lower edge of screen with 59% V
  • NEC NP-P452H | Users Manual - Page 84
    5. Installation and Connections Lens shifting range This projector is equipped with a lens shift function (→ page %, −0% Horizontal direction: ±25% 62%V 25%H 25%H Width of projected image 100%V [P502W/P452W] Lens shifting range: Vertical direction: +59%, −0% Horizontal direction: ±28% 25%H
  • NEC NP-P452H | Users Manual - Page 85
    ≈ 32.7"/83 cm, to the right approximately 32.7"/83 cm. [P502W/P452W] According to the "Table of screen sizes and dimensions" (→ projector. Reflecting the Image Using a mirror to reflect your projector's image enables you to enjoy a much larger image when a smaller space is required. Contact your NEC
  • NEC NP-P452H | Users Manual - Page 86
    Computer cables and HDMI can be used to connect to a computer. The HDMI cable is not enclosed with the projector. Please get ready a suitable cable for the connection. NOTE: Signals supported by Plug & Play (DDC2) COMPUTER IN analog Yes INPUT HDMI 1 IN digital Yes HDMI 2 IN digital Yes HDMI
  • NEC NP-P452H | Users Manual - Page 87
    NEC ISS-6020 switcher. NOTE: An image may not be displayed correctly when a Video source is played back via a commercially available scan converter. This is because the projector , restart your PC. • The COMPUTER video input terminals support Windows Plug and Play. • A Mac signal adapter (commercially available
  • NEC NP-P452H | Users Manual - Page 88
    cable (not supplied) NOTE: • The AUDIO OUT mini jack does not support Headphone terminal. • When audio equipment is connected, the projector speaker is disabled. • The signal output from the MONITOR OUT (COMP.) of this projector is for projecting image on exclusive one display. • When no signal is
  • NEC NP-P452H | Users Manual - Page 89
    name for its appropriate input terminal after turning on the projector. Input terminal SOURCE button on the projector cabinet Button on the remote control VIDEO IN VIDEO (VIDEO) NOTE: Refer to your VCR owner's manual for more information about your equipment's video output requirements. NOTE
  • NEC NP-P452H | Users Manual - Page 90
    name for its appropriate input terminal after turning on the projector. Input terminal COMPUTER IN SOURCE button on the projector cabinet COMPUTER Button on the remote control (COMPUTER 1) NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output
  • NEC NP-P452H | Users Manual - Page 91
    connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the HDMI IN terminal of your projector. HDMI 1 IN HDMI 2 IN HDMI cable (not supplied) Use High Speed HDMI® Cable. Audio cable (not supplied) • Select the source name for its appropriate input
  • NEC NP-P452H | Users Manual - Page 92
    of terminals are vary depending on camera model. Please check user's manual of your camera for details. Video cable (not supplied) • Select input terminal after turning on the projector. Input terminal COMPUTER IN VIDEO IN SOURCE button on the projector cabinet COMPUTER VIDEO Button on the
  • NEC NP-P452H | Users Manual - Page 93
    use only 1 of the ports (it is not possible to connect both ports to the LAN). For controlling the projector by a HDBaseT transmitter whose control signal is not supported (or with which cannot connect the projector) or over the network, connect to the LAN port. At the same time, for controlling the
  • NEC NP-P452H | Users Manual - Page 94
    the USB Wireless LAN Unit in the area where the use of wireless LAN equipment is prohibited, remove the USB Wireless LAN Unit from the projector. • Buy the appropriate USB Wireless LAN Unit for your country or area. NOTE: • Your computer's wireless LAN adapter (or unit) must be complied with Wi
  • NEC NP-P452H | Users Manual - Page 95
    4. Mount the wireless LAN cover. (1)Insert the hook on the back of the cover into the groove in the projector and close the wireless LAN cover. (2)Turn the screw clockwise to tighten it. 5. Installation and Connections Groove Hook * To remove the USB Wireless LAN Unit,
  • NEC NP-P452H | Users Manual - Page 96
    and Connections Example of wireless LAN connection To use a LAN connection, you are required to set the Wireless LAN settings on the projector menu. Select [SETUP] → [INSTALLATION] → [NETWORK SETTINGS]. (→ page 58). The network settings can also be selected from the APPS menu. PC with wireless
  • NEC NP-P452H | Users Manual - Page 97
    sold commercially. Control signals (serial and LAN) and remote control signals (IR commands) from an external device are only supported when the projector's power is turned on. Connection example Computer (for control use) Remote control Example of a transmission device Ethernet/HDBaseT Computer
  • NEC NP-P452H | Users Manual - Page 98
    is on). The 2 (two) methods below can be used to turn on the projector's power when it is in standby mode. 1. The projector can be operated by connecting the computer and projector to the network (on the projector, using the LAN port and PC Control Utility application with [STANDBY MODE] set to
  • NEC NP-P452H | Users Manual - Page 99
    information about each function on the APPS MENU is explained on our web site. Please search it by the model name of your projector. http://www.nec-display.com/dl/en/pj_manual/lineup.html APPS MENU screen display REMOTE DESKTOP CONNECTION VIEWER FOCUS Indicating the selected item. Surrounded in
  • NEC NP-P452H | Users Manual - Page 100
    web site and install it on these. (→ page 112) Miracast By wirelessly connecting the terminal units supporting the Miracast such as the Android with the projector, it enables the projector to project images transmitted from these terminals. Before connecting these terminal units, set [Miracast] in
  • NEC NP-P452H | Users Manual - Page 101
    to share images and files among the projector and computers in the same network by accessing the web server of the projector utilizing the web browser. Sharing files ABC in the WEB SERVER functions. NETWORK SERVICE Set up various setting for the AMX, HTTP server, PJLink, Alert mail and CRESTRON. 90
  • NEC NP-P452H | Users Manual - Page 102
    be used for operating the APPS MENU. Perform the set up for using it. PROGRAM TIMER Once day and time is set up, changing the projector's condition in powering ON/standby, switching input signals, and switching ECO mode can be automatically performed. DATE AND TIME Determine time zone and summer
  • NEC NP-P452H | Users Manual - Page 103
    not support "Meeting Mode" in Image Express Utility 2.0 supplied with our other models. Download Service and Operating Environment Please visit our website about operating environment and download service for each software: Visit URL: http://www.nec-display.com/dl/en/index.html Download - Projector
  • NEC NP-P452H | Users Manual - Page 104
    over a LAN (Image Express Utility Lite) Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM allows you to send the computer's screen image to the projector over a wired or wireless LAN. Image Express Utility Lite is a program compatible with Windows. Image Express
  • NEC NP-P452H | Users Manual - Page 105
    space (about 100 MB) to install the program. 1. Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed , click "I agree." and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation
  • NEC NP-P452H | Users Manual - Page 106
    LAN by following the instructions in "Connecting to a Wired LAN" (→ page 82) and "Connecting to a Wireless LAN (Optional: NP05LM series)" (→ page 83). Step 3: Start Image Express Utility Lite. 1. On Windows, click "Start" → "All programs" → "NEC Projector UserSupportware" → "Image Express Utility
  • NEC NP-P452H | Users Manual - Page 107
    SD cards if it is copied beforehand. This will eliminate the trouble of installing Image Express Utility Lite to your computer. 1. Copy . 7 MB) from the "IEU_Lite (removable-media)" folder in the supplied NEC Projector CD-ROM to the root directory of your removable media. 2. Insert your removable
  • NEC NP-P452H | Users Manual - Page 108
    Express Utility Lite for Mac on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM Applications folder on OS X. Step 2: Connect the projector to a LAN Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page
  • NEC NP-P452H | Users Manual - Page 109
    an Angle (GCT) Install Image Express Utility Lite on the computer and launch it to display the control window. (→ page 94, 95) Preparation: Adjust the projector position or the zoom so that the projected image can cover the whole screen area. 1. Click the " button. " (Others) icon and then the
  • NEC NP-P452H | Users Manual - Page 110
    4. Click the " "(Projection) icon and then the " button. "(Exit) 5. Click "Yes". 6. Start the Image Express Utility Lite again. 7. Click the " " (Picture) icon and then the " " button. 7. User Supportware The "4-point Correction" window will be displayed. 8. Click the "Start Correction" button
  • NEC NP-P452H | Users Manual - Page 111
    to exit the GCT. TIP: • After performing the 4-point correction, you can save the 4-point correction data to the projector by clicking "File" → "Export to the projector..." on the "4-point Correction" window. • See the Help of Image Express Utility Lite for operating "4-point Correction" window and
  • NEC NP-P452H | Users Manual - Page 112
    Utility Pro 4/ Pro 5) Using the utility software "PC Control Utility Pro 4" and "PC Control Utility Pro 5" included on the companion NEC Projector CD-ROM, the projector can be controlled from a computer over a LAN. PC Control Utility Pro 4 is a program compatible with Windows. (→ this page) PC
  • NEC NP-P452H | Users Manual - Page 113
    USER LICENSE AGREEMENT" carefully. 4 If you agree, click "I accept the terms in the license agreement" and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window. TIP: • Uninstalling
  • NEC NP-P452H | Users Manual - Page 114
    to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 82) and "Connecting to a Wireless LAN (Optional: NP05LM series)" (→ page 83). Step 3: Start PC Control Utility Pro 4 Click "Start" → "All programs" or "Programs" → "NEC Projector User Supportware" → "PC Control Utility
  • NEC NP-P452H | Users Manual - Page 115
    PC Control Utility Pro 5 on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM instructions on the installer screens to complete the installation. Step 2: Connect the projector to a LAN Connect the projector to the LAN by following the instructions in
  • NEC NP-P452H | Users Manual - Page 116
    Utility Pro 5 to the Trash icon. • The configuration file of PC Control Utility Pro 5 is located in "/Users//Application Data/NEC Projector User Supportware/PC Control Utility Pro 5". Viewing the Help of PC Control Utility Pro 5 • Displaying the Help file of PC Control Utility Pro
  • NEC NP-P452H | Users Manual - Page 117
    NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed on your computer screen. This will help you perform operations such as projector is not supported by Virtual Remote Tool. • For update information on Virtual Remote Tool, visit our website: http://www.nec-display.com/dl
  • NEC NP-P452H | Users Manual - Page 118
    logo by using the image file (P502H/P452H: /Logo/NEC_logo2015_1920x1080.bmp, P502W/P452W: /Logo/NEC_logo2015_1280x800.bmp) inclulded on the supplied NEC Projector CD-ROM. TIP: • The projector's COMPUTER IN terminal supports DDC/CI (Display Data Channel Command Interface). DDC/CI is a standard
  • NEC NP-P452H | Users Manual - Page 119
    . Read "END USER LICENSE AGREEMENT" carefully. 4 If you agree, click "I accept the terms in the license agreement" and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window. 108
  • NEC NP-P452H | Users Manual - Page 120
    /Change" or "Uninstall". • When the "User Account Control" windows is displayed, click "Continue". Follow the instructions on the screens to complete the uninstallation. Step 2: Connect the projector to the computer 1 Use the supplied computer cable (VGA) to connect the COMPUTER IN terminal of the
  • NEC NP-P452H | Users Manual - Page 121
    menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual the first time, "Easy Setup" window will be displayed. Follow the instructions on the screens When "Easy Setup" is completed, the Virtual Remote Tool
  • NEC NP-P452H | Users Manual - Page 122
    Click "Help". The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click "Start" → "All programs" or "Programs" → "NEC Projector User Supportware" → "Virtual Remote Tool" → and then "Virtual Remote Tool Help" in this order. The Help screen will be displayed. 111
  • NEC NP-P452H | Users Manual - Page 123
    photos and documents saved on terminals as a smartphone or a tablet to the projector via the wireless LAN and project them. There are two kinds of Wireless Image For Android http://www.nec-display.com/dl/en/pj_android/wiu_for-android.html For iOS http://www.nec-display.com/dl/en/pj_ios/wiu_for-ios.html
  • NEC NP-P452H | Users Manual - Page 124
    . Intake vent filter: At the bottom of control panel. Prevent the projector inside from dust and dirt accumulation. Color wheel filter: Fixed inside the lamp cover. Prevent the color wheel from dust and dirt accumulation. In this manual, call the intake vent filter "Filter (A)" and the color wheel
  • NEC NP-P452H | Users Manual - Page 125
    out the plug from the wall outlet. 2. Pinch the knob at the bottom of the filter case and pull it out. • If you put the projector upside down for cleaning as the illustration, please lay a mat as a cloth for protecting the cabinet top from damage. 8. Maintenance 3. Remove the Filter (A) from the
  • NEC NP-P452H | Users Manual - Page 126
    cut off part of the Filter (A) meeting with the knob part on the filter case. 8. Maintenance Knob Cut off 6. Insert the filter case to the projector cabinet. Make sure that the filter case is inserted in the correct orientation. 7. Clear the filter hour meter. Connect the power cord plug to the
  • NEC NP-P452H | Users Manual - Page 127
    8. Maintenance ❷ Cleaning the Lens • Turn off the projector before cleaning. • Do not scratch or mar the projection window as it is made of glass. • Use a blower or lens paper to clean the projection
  • NEC NP-P452H | Users Manual - Page 128
    in malfunction. • Do not scratch or hit the cabinet with your fingers or any hard objects • Contact your dealer for cleaning the inside of the projector. NOTE: Do not apply volatile agent such as insecticide on the cabinet, the projection window, or the screen. Do not leave a rubber or vinyl product
  • NEC NP-P452H | Users Manual - Page 129
    lamp type. Replacement lamp: NP39LP: P502H/P502W NP38LP: P452H/P452W The replacement lamp comes NEC dealer for lamp replacement. *NOTE: This message will be displayed under the following conditions: • for one minute after the projector has been powered on • when the (POWER) button on the projector
  • NEC NP-P452H | Users Manual - Page 130
    To replace the lamp and the Filter (B): 1. Remove the lamp cover. (1)Loosen the lamp cover screw • The lamp cover screw is not removable. 8. Maintenance (2)Push and slide the lamp cover off. a b 2. Pull out the filter case. Pinch the filter case handle and pull it in the arrow indicated
  • NEC NP-P452H | Users Manual - Page 131
    (2)Vacuum off accumulated dust and dirt on inside and outside of the filter case. (3)Fix a new Filter (B) onto the filter case. 4. Remove the lamp housing. (1)Loosen the three screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. • The three screws are
  • NEC NP-P452H | Users Manual - Page 132
    5. Install a new lamp housing. (1)Insert a new lamp housing until the lamp housing is plugged into the socket. (2)Push the top center of the lamp housing to secure it. 8. Maintenance (3)Secure it in place with the three screws. • Be sure to tighten the screws. 6. Insert for resetting the filter
  • NEC NP-P452H | Users Manual - Page 133
    lamp and Filter (B) replacement. Go on to the Filter (A) replacement. NOTE: When you continue to use the projector for another 100 hours after the lamp has reached the end of its life, the projector cannot turn on and the menu is not displayed. If this happens, press the HELP button on the
  • NEC NP-P452H | Users Manual - Page 134
    will damage the filter membrane. • Put filters into place. Incorrect attachment of a filter may cause dust and dirt to get into the inside of the projector. Before replacing the Filter (A), make sure to replace the lamp and Filter (B). (→ page 119) 1. Pinch the knob at the bottom of the filter case
  • NEC NP-P452H | Users Manual - Page 135
    off part of the Filter (A) meeting with the knob part on the filter case. 8. Maintenance Knob Cut off 5. Insert the Filter case to the projector cabinet. Make sure that the filter case is inserted in the correct orientation. This completes the filter replacement. Go on to the clearing lamp and
  • NEC NP-P452H | Users Manual - Page 136
    9. Appendix ❶ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages over 1 minute and power on the projector again. Even though the lamp is not turned on, ask your dealer or service personnel for repair. Both the built
  • NEC NP-P452H | Users Manual - Page 137
    will start to blink (2-cycle On and Off). Should this happen, do the following: • Unplug the power cord after the cooling fans stop. • Move the projector to a cooler location if the room where you are presenting is particularly too warm. • Clean the vents if they are clogged with dust. • Wait about
  • NEC NP-P452H | Users Manual - Page 138
    for some time and then the projector will display the image. Wait for a moment. • In case it's hard to think the trouble is not caused on the above your driver, refer to the user guide accompanied with your computer or graphics card, or contact the support center for your computer manufacturer.
  • NEC NP-P452H | Users Manual - Page 139
    resolution you are trying to display is supported by the projector. (→ page 136) • Adjust the computer image manually with the [HORIZONTAL]/[VERTICAL] in function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations
  • NEC NP-P452H | Users Manual - Page 140
    projector's performance. 9. Appendix Model name NP-P502H NP-P502W NP-P452H NP- VESA standards Main adjustment functions Manual zoom, manual focus, manual lens shift, input signal compatible LipSync compatible, HDCP compatible (*4), Supports 3D Audio input HDMI: Sampling frequency
  • NEC NP-P452H | Users Manual - Page 141
    NP-P502H NP-P502W NP-P452H Deep Color (color depth): Support 8/10/12 bits Colorimetry: Support RGB, YCbCr444 and YCbCr422 Support LipSync , HDCP (*4), 3D Sampling frequency: 32/44.1/48 kHz Sampling bit: 16/20/24 bit Stereo mini Jack × 1 1 for USB memory 1 for service RJ-45 × 1, Supports
  • NEC NP-P452H | Users Manual - Page 142
    ❸ Cabinet Dimensions Unit: mm (inch) 9. Appendix 306 (12) 302 (11.9) Lens center 362 (14.3) 91 (3.6) 139 (5.5) 129 (5.1) 81 (3.2) 68 (2.7) 150 (5.9) 130 (5.1) 5 (0.2) 175 (6.9) 200 (7.9) 131
  • NEC NP-P452H | Users Manual - Page 143
    bundled cables in the cable cover. Doing so may damage the power cord, resulting in a fire. • Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover. Doing so may damage the cable cover, resulting in injury. Attaching the cable cover Tool
  • NEC NP-P452H | Users Manual - Page 144
    Removing the cable cover 1. Loosen the cable cover screws until the Phillips screwdriver goes into a freewheeling condition and remove the cover. • When suspended from the ceiling, hold so that the cable cover does not drop. • The screws cannot be removed. 9. Appendix 133
  • NEC NP-P452H | Users Manual - Page 145
    9. Appendix ❺ Pin assignments and signal names of main terminals COMPUTER IN Terminal (Mini D-Sub 15 Pin) Connection and signal level of each pin 11 12 13 14 15 6 7 8 9 10 1 23 45 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
  • NEC NP-P452H | Users Manual - Page 146
    Ethernet/HDBaseT/LAN Port (RJ-45) 12345678 Pin No. 1 2 3 4 5 6 7 8 Signal TxD+/HDBT0+ TxD−/HDBT0− RxD+/HDBT1+ Disconnection/HDBT2+ Disconnection/HDBT2− RxD−/HDBT1− Disconnection/HDBT3+ Disconnection/HDBT3− USB Port (Type A) 1 2 3 4 Pin No. 1 2 3 4 VBUS D− D+ Grounding Signal PC CONTROL Port
  • NEC NP-P452H | Users Manual - Page 147
    Native resolution on 1080p model (NP-P502H/NP-P452H) *2 Native resolution on WXGA model (NP-P502W/NP-P452W) *3 The projector may fail to display these signals signals are supported for Frame Sequential only. NOTE: • An image with higher or lower resolution than the projector's native resolution
  • NEC NP-P452H | Users Manual - Page 148
    Send" together on both ends of the cable to simplify cable connection. NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. 137
  • NEC NP-P452H | Users Manual - Page 149
    the computer for displaying the web page correctly. 1. Access to the software download support page in our web site. URL: http://www.nec-display.com/dl/en/pj_soft/lineup.html 2. Check if the software installed on the projector in use is updated. • You can check the software version from either
  • NEC NP-P452H | Users Manual - Page 150
    of the HTTP transmission. The error codes other than above may be displayed. If an error is found during the software update, turn on the projector and update the file again. When the software update is not completed properly even if you tried to update several times, please consult your dealer
  • NEC NP-P452H | Users Manual - Page 151
    service personnel, check the following list to be sure repairs are needed also by referring to the "Troubleshooting" section in your user's manual. This checklist below will help us solve your problem □ Input source's resolution and frequency are supported by the projector. □ Image is too dark. □
  • NEC NP-P452H | Users Manual - Page 152
    space below please describe your problem in detail. 9. Appendix Information on application and environment where your projector is used Projector Model number: Serial No rate: Video adapter: Other: DVD player Signal cable NEC standard or other manufacturer's cable? Model number: Length:
  • NEC NP-P452H | Users Manual - Page 153
    States, Canada, and Mexico) Please take time to register your new projector. This will activate your limited parts and labor warranty and InstaCare service program. Visit our web site at www.necdisplay.com, click on support center/register product and submit your completed form online. Upon receipt
  • NEC NP-P452H | Users Manual - Page 154
    © NEC Display Solutions, Ltd. 2015 7N952321
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Projector
P502H/P452H
P502W/P452W
User’s Manual
Model No.
NP-P502H, NP-P452H, NP-P502W, NP-P452W