NEC NP-P502H Users Manual

NEC NP-P502H Manual

Get NEC NP-P502H PDF manuals and user guides View all NEC NP-P502H manuals
Add to My Manuals
Save this manual to your list of manuals

NEC NP-P502H manual content summary:

  • NEC NP-P502H | Users Manual - Page 1
    Projector P502H/P452H P502W/P452W User's Manual Model No. NP-P502H, NP-P452H, NP-P502W, NP-P452W
  • NEC NP-P502H | Users Manual - Page 2
    of Apple Inc. registered in the U.S. and other countries. • App Store is a service mark of Apple Inc. • IOS is a trademark or registered trademark of Cisco in manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), NEC will
  • NEC NP-P502H | Users Manual - Page 3
    this manual carefully before using your NEC projector and keep the manual handy ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the provided. The information should be read carefully to avoid problems. WARNING: TO PREVENT FIRE OR SHOCK, DO NOT
  • NEC NP-P502H | Users Manual - Page 4
    specified by NEC Display Solutions of America, Inc. in this manual. Failure to please contact your supplier. Important Safeguards These safety instructions are to ensure the long life of your addition, the ceiling must be strong enough to support the projector and the installation must be in
  • NEC NP-P502H | Users Manual - Page 5
    a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel. • Do not place any objects on top of the projector. • Do not touch the power plug during a thunderstorm. Doing so can cause
  • NEC NP-P502H | Users Manual - Page 6
    operate normally when you follow the instructions described in this user's manual. - If the projector has been the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the soft case law. FOR MORE INFORMATION, CONTACT: NEC Display Solutions of America, Inc. 500
  • NEC NP-P502H | Users Manual - Page 7
    Please dispose according to Local, State or Federal Laws. Lamp Replacement • Use the specified lamp for safety and performance. • To replace the lamp, follow all instructions provided on page 118. • Be sure to replace the lamp when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE
  • NEC NP-P502H | Users Manual - Page 8
    Before viewing, be sure to read health care precautions that may be found in the user's manual included with your LCD shutter eyeglasses or your 3D compatible content such as DVDs, video games, computer , please visit the company website: URL: http://www.nec-display.com/global/support/index.html vi
  • NEC NP-P502H | Users Manual - Page 9
    ❶ What's in the Box?...1 ❷ Introduction to the Projector 2 General...2 Installation...2 Videos...2 Network...2 Energy-saving...3 About this user's manual 3 ❸ Part Names of the Projector 4 Front...4 Mounting the lens cap strap 4 Rear...5 Controls/Indicators...6 Terminal Panel Features 7 ❹ Part
  • NEC NP-P502H | Users Manual - Page 10
    Use of the Projector [SECURITY 30 ❻ Viewing 3D Images...33 LCD shutter eyeglasses (recommended 33 Steps for viewing 3D images on the projector 33 Troubleshooting on viewing 3D images 36 4. Using On-Screen Menu 37 ❶ Using the Menus...37 Menu Elements...38 ❷ List of Menu Items...39 ❸ Menu
  • NEC NP-P502H | Users Manual - Page 11
    ❷ Cleaning the Lens...116 ❸ Cleaning the Cabinet 117 ❹ Replacing the Lamp and the Filters 118 9. Appendix...125 ❶ Troubleshooting...125 Indicator Messages 125 Common Problems & Solutions 127 If there is no picture, or the picture is not displayed correctly 128 ❷ Specifications...129 ❸ Cabinet
  • NEC NP-P502H | Users Manual - Page 12
    Information (For North America: 7N8N6521) (For Other countries than North America: 7N8N6521 and 7N8N6531) • Quick Setup Guide (7N8N6541)/ (7N8N6551) NEC Projector CD-ROM User's manual (PDF) and the utility software (7N952321) For North America only Limited warranty For customers in Europe: You
  • NEC NP-P502H | Users Manual - Page 13
    high brightness Model name DMD panel Resolution P502H/P452H 0.65 type 1920 × 1080 pixels P502W/P452W shutter-type 3D eyewear and 3D emitters that support Xpand 3D. Network • Equips the feature The five utility software stored in the enclosed NEC Projector CD-ROM (Image Express Utility Lite (
  • NEC NP-P502H | Users Manual - Page 14
    [INFO.] on the on-screen menu (CARBON METER). About this user's manual The fastest way to get started is to take your time and do everything right . Take a few minutes now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an overview. If
  • NEC NP-P502H | Users Manual - Page 15
    ❸ Part Names of the Projector Front Lens shift dials (Horizontal/Vertical) (→ page 17) Zoom Lever (→ page 19) Lens Focus Ring (→ page 19) Lens Cap Remote Sensor (→ page 9) Intake Vent (→ page 113) Mounting the lens cap strap 1. Insert the tip of the strap into the lens cap mount hole and pass the
  • NEC NP-P502H | Users Manual - Page 16
    . The security chain opening accepts security wires or chains up to 0.18 inch/4.6 mm in diameter. Intake Vent Filter (→ page 113, 123) * This security slot supports the MicroSaver® Security System. 5
  • NEC NP-P502H | Users Manual - Page 17
    Controls/Indicators 2 34 5 6 8 9 1. (POWER) Button (→ page 12, 24) 2. POWER Indicator (→ page 11, 12, 24, 125) 3. STATUS Indicator (→ page 125) 4. LAMP Indicator (→ page 125) 5. ECO Button (→ page 28) 6. SOURCE Button (→ page 14) 7. AUTO ADJ. Button (→ page 23) 8. MENU Button (→ page 37) 9
  • NEC NP-P502H | Users Manual - Page 18
    service purpose only) 16. REMOTE Connector (Stereo Mini) Use this connector for wired remote control of the projector using the NEC and the projector is connected to a commercially-available transmission device that supports HDBaseT, remote control operations in infra-red cannot be carried out if
  • NEC NP-P502H | Users Manual - Page 19
    ❹ Part Names of the Remote Control 1. Introduction 1 2 5 8 9 11 ʴ 15 14 18 19 22 23 24 27 33 1. Infrared Transmitter 3 (→ page 9) 4 6 2. POWER ON Button (→ page 12) 7 3. POWER STANDBY Button 10 (→ page 24) 20. EXIT Button (→ page 37) 21 Button (→ page 37) 22. ENTER Button (→
  • NEC NP-P502H | Users Manual - Page 20
    1. Introduction Battery Installation 1. Press firmly and slide the battery cover off. 2. Install new batteries (AAA). Ensure that you have the batteries' polarity (+/−) aligned correctly. 3. Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries
  • NEC NP-P502H | Users Manual - Page 21
    2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen. ❶ Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 11) Step 2 • Turning on the projector (→ page 12) Step 3 •
  • NEC NP-P502H | Users Manual - Page 22
    2. Projecting an Image (Basic Operation) ❷ Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see "5. Installation and Connections" on page 69. Connect the
  • NEC NP-P502H | Users Manual - Page 23
    ❸ Turning on the Projector 2. Projecting an Image (Basic Operation) 1. Remove the lens cap. With the lens cap's stopper pressed up, pull forward and off. Stopper 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator lights blue and
  • NEC NP-P502H | Users Manual - Page 24
    2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 30 menu languages. To select a menu language, follow these steps: 1. Use the or
  • NEC NP-P502H | Users Manual - Page 25
    2. Projecting an Image (Basic Operation) ❹ Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once. The projector will search for the available input
  • NEC NP-P502H | Users Manual - Page 26
    2. Projecting an Image (Basic Operation) Selecting Default Source You can so that it will be displayed each time the projector is turned on. 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button twice to select [SETUP] and the ▼ button or the ENTER button to select [GENERAL].
  • NEC NP-P502H | Users Manual - Page 27
    2. Projecting an Image (Basic Operation) ❺ Adjusting the Picture Size and Position Use the lens shift dial, the adjustable tilt foot lever, the zoom lever/zoom ring and the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the
  • NEC NP-P502H | Users Manual - Page 28
    2. Projecting an Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) CAUTION Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them. 1. Turn the lens shift
  • NEC NP-P502H | Users Manual - Page 29
    shift adjustment range ([ORIENTATION]: [DESKTOP FRONT]). • For the lens shift adjustment range regarding the [CEILING FRONT] projection, see page 73. [P502H/P452H] 25%H 25%H Width of projected image 62%V [P502W/P452W] 100%V 25%H 100%H 25%H 59%V 28%H 28%H Height of projected image Width
  • NEC NP-P502H | Users Manual - Page 30
    Focus Use the FOCUS ring to obtain the best focus. 2. Projecting an Image (Basic Operation) NOTE: • Recommend to perform the focus adjustment after leaving the projector under the state the TEST PATTERN has been projected for over 30 minutes. Please refer page 58 about the TEST PATTERN. Focus
  • NEC NP-P502H | Users Manual - Page 31
    Adjusting the tilt (Tilt foot) Adjusting the left and right tilt. 2. Projecting an Image (Basic Operation) 1. Turn the left and right tilt feet to adjust. The tilt feet lengthen and shorten when turned. The height of the projected image is adjusted by turning the left and right tilt feet. If the
  • NEC NP-P502H | Users Manual - Page 32
    2. Projecting an Image (Basic Operation) ❻ Correcting Keystone Distortion [KEYSTONE] When the projector is not exactly perpendicular to the screen, keystone distortion occurs.To overcome it, you can use the "Keystone" function, a digital technology that can adjust for keystone-type distortion,
  • NEC NP-P502H | Users Manual - Page 33
    2. Projecting an Image (Basic Operation) 4. Press the ▲ button to select [HORIZONTAL] and then use the ◀ or ▶ so that the top and bottom sides of the projected image are parallel. • Adjust the horizontal keystone distortion. 5. Repeat steps 2 and 4 to correct keystone distortion. 6. After completing
  • NEC NP-P502H | Users Manual - Page 34
    or may not be displayed correctly. • If the Auto Adjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE] manually. (→ page 46, 47) ❽ Turning Up or Down Volume Sound level from the speaker or audio output can be adjusted. TIP: When no menus
  • NEC NP-P502H | Users Manual - Page 35
    2. Projecting an Image (Basic Operation) ❾ Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The confirmation message will be displayed. • The confirmation message displayed when the power is
  • NEC NP-P502H | Users Manual - Page 36
    ❿ When Moving the Projector Preparation: Make sure that the projector is turned off. 2. Projecting an Image (Basic Operation) 1. If the separately sold cable cover is mounted, remove it. (→ page 132) 2. Unplug the power cord. 3. Disconnect any other cables. • Remove the USB memory if it is
  • NEC NP-P502H | Users Manual - Page 37
    3. Convenient Features ❶ Turning off the Image and Sound Press the AV-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. NOTE: • Even though the image is turned off, the menu still remains on the screen. ❷ Freezing a Picture Press the
  • NEC NP-P502H | Users Manual - Page 38
    ❸ Magnifying a Picture You can enlarge the picture up to four times. NOTE: • The maximum magnification may be less than four times depending on the signal. To do so: 1. Press the D-ZOOM (+) button to magnify the picture. To move the magnified image, use the or ▶ button. 3. Convenient Features 2.
  • NEC NP-P502H | Users Manual - Page 39
    3. Convenient Features ❹ Changing Eco Mode/Checking Energy-Saving Effect Using Eco Mode [ECO MODE] The ECO MODE (NORMAL and ECO) increases lamp life, while lowering power consumption and cutting down on CO2 emissions. Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL]
  • NEC NP-P502H | Users Manual - Page 40
    3. Convenient Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector's [ECO MODE] is set. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS
  • NEC NP-P502H | Users Manual - Page 41
    3. Convenient Features ❺ Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is
  • NEC NP-P502H | Users Manual - Page 42
    3. Convenient Features 7. Type in the same combination of buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button
  • NEC NP-P502H | Users Manual - Page 43
    To disable the SECURITY function: 3. Convenient Features 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen
  • NEC NP-P502H | Users Manual - Page 44
    read health care precautions that may be found in the user's manual included with your LCD shutter eyeglasses or your 3D compatible content LCD shutter eyeglasses to view 3D images. Also refer to the user's manual accompanied with your LCD shutter eyeglasses for more information. On-screen menu for
  • NEC NP-P502H | Users Manual - Page 45
    3D images [HDMI1/HDMI2/COMPUTER/VIDEO/ HDBaseT] This function switches the 3D mode between ON and OFF for each input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make sure that [3D] is displayed in the top right of the screen after the
  • NEC NP-P502H | Users Manual - Page 46
    the 3D SYNC terminal of the projector. NOTE: • Use an active shutter 3D eyewear (compliance with VESA) • Check the operating conditions described in the user manual of the Blu-ray player. • Please connect the DIN terminal of the 3D emitter to the 3D SYNC of the projector. • The 3D eyewear allows
  • NEC NP-P502H | Users Manual - Page 47
    Features Troubleshooting on viewing 3D images If images will not be displayed in 3D or 3D images appear as 2D, check the following table. Also refer to the user's manual accompanied 3D format of the 3D video contents is not supported. • Please check with the company selling the 3D video contents. 36
  • NEC NP-P502H | Users Manual - Page 48
    4. Using On-Screen Menu ❶ Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT in the bottom show
  • NEC NP-P502H | Users Manual - Page 49
    Menu Elements Tab Available buttons Source Highlight 4. Using On-Screen Menu Slide bar Solid triangle Radio button Wireless symbol ECO mode symbol High Altitude symbol Thermometer symbol Menu mode Off Timer remaining time Key Lock symbol Menu windows or dialog boxes typically have the following
  • NEC NP-P502H | Users Manual - Page 50
    4. Using On-Screen Menu ❷ List of Menu Items Some menu items are not available depending on the input source. The below listed menu items are on the advanced menu. The mark (B) is added to the items on the basic menu. Refer to 88 pages about the APPS MENU. Menu Item SOURCE ADJUST SETUP HDMI1
  • NEC NP-P502H | Users Manual - Page 51
    FORMAT L/R INVERT 3D L/R INVERT 3D GLASSES FORMAT L/R INVERT Default Options COLOR COLOR, MONOCHROME ON OFF, ON ON OFF, ON OFF OFF, ON AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC BLUE BLUE, BLACK, LOGO ON OFF, ON OFF OFF, 100H, 500H, 1000H, 2000H DESKTOP DESKTOP FRONT
  • NEC NP-P502H | Users Manual - Page 52
    , NON-INTERLACE RGB, VIDEO, YCbCr NTSC, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM 8[bits], 10[bits], 12[bits] FULL, ENHANCED, DEFAULT SUPPORTED, NOT SUPPORTED NORMAL, WARNING, ABNORMAL HDBaseT, ETHERNET, LOW POWER, DISCONNECT NO LINK, HDBaseT, LOW POWER, ETHERNET NO HDMI, HDMI ON, HDCP ON
  • NEC NP-P502H | Users Manual - Page 53
    , select [COMPUTER]. VIDEO Selects what is connected to your VIDEO input-VCR, DVD player or document camera. HDBaseT Projects the signal transmitted from the terminals supported HDBaseT. (→ page 86) APPS Display the APPS MENU or the function in the APPS MENU that was used last time. 42
  • NEC NP-P502H | Users Manual - Page 54
    4. Using On-Screen Menu ❹ Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are eight factory presets optimized for various types of images. You can
  • NEC NP-P502H | Users Manual - Page 55
    [DETAIL SETTINGS] 4. Using On-Screen Menu Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 8]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT
  • NEC NP-P502H | Users Manual - Page 56
    [CONTRAST] Adjusts the intensity of the image according to the incoming signal. 4. Using On-Screen Menu [BRIGHTNESS] Adjusts the brightness level or the back raster intensity. [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies
  • NEC NP-P502H | Users Manual - Page 57
    [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. 4. Using On-Screen Menu CLOCK Use this item to fine tune the computer image or to remove any vertical banding that
  • NEC NP-P502H | Users Manual - Page 58
    Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. 4. Using On-Screen Menu - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and
  • NEC NP-P502H | Users Manual - Page 59
    the incoming signal and displays it in its appropriate aspect ratio. • This table shows typical resolutions and aspect ratios that most computers support. Resolution VGA 640 × 480 SVGA 800 × 600 XGA 1024 × 768 WXGA 1280 × 768 WXGA 1280 × 800 WXGA+ 1440 × 900 SXGA 1280 × 1024
  • NEC NP-P502H | Users Manual - Page 60
    Sample image when the appropriate aspect ratio is automatically determined [Computer signal] Aspect ratio of incoming signal 4:3 5:4 16:9 15:9 P502H/P452H 16:10 Sample image when the appropriate aspect ratio is automatically determined P502W/P452W [Video signal] Aspect ratio of incoming
  • NEC NP-P502H | Users Manual - Page 61
    4. Using On-Screen Menu ❺ Menu Descriptions & Functions [SETUP] [GENERAL] Correcting Keystone Distortion Manually [KEYSTONE] You can correct horizontal or vertical keystone manually. [HORIZONTAL] and [VERTICAL] (simultaneously adjustable) correction can be selected. NOTE: • Some items are not
  • NEC NP-P502H | Users Manual - Page 62
    Using the Wall Color Correction [WALL COLOR] 4. Using On-Screen Menu This function allows for quick adaptive color correction in applications where the screen material is not white. Setting various items related to lamp brightness [ECO SETTINGS] This option allows you to decrease the power
  • NEC NP-P502H | Users Manual - Page 63
    the superimposed text or closed caption within the screen. • The projector does not support optional extended characters for closed captioning. Using Off Timer [OFF TIMER] 1. Select one of 30 languages for on-screen instructions. NOTE: Your setting will not be affected even when [RESET] is done from the
  • NEC NP-P502H | Users Manual - Page 64
    option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the factory preset. 53
  • NEC NP-P502H | Users Manual - Page 65
    4. Using On-Screen Menu Selecting a Color or Logo for Background [BACKGROUND] Use this feature to display a blue/black screen or logo when no signal is available. The default background is [BLUE]. NOTE: • When [SOURCE DISPLAY] is turned on, the no-signal guidance prompting you to check for an
  • NEC NP-P502H | Users Manual - Page 66
    [INSTALLATION] 4. Using On-Screen Menu Selecting Projector Orientation [ORIENTATION] This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection. DESKTOP FRONT CEILING REAR
  • NEC NP-P502H | Users Manual - Page 67
    ] is done from the menu. Selecting Communication Speed [COMMUNICATION SPEED] This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on
  • NEC NP-P502H | Users Manual - Page 68
    the CONTROL ID setting. NOTE: • When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the CONTROL ID function. (In this case the buttons on the projector cabinet can be used.) • Your setting will not be affected even when [RESET
  • NEC NP-P502H | Users Manual - Page 69
    4. Using On-Screen Menu Using Test Pattern [TEST PATTERN] Displays the test pattern for adjusting distortion on the screen and the focus at the time of the projector setup. Once the [TEST PATTERN] on the onscreen menu is selected, the pattern for adjustment will be displayed on. If you find
  • NEC NP-P502H | Users Manual - Page 70
    [OPTIONS(1)] 4. Using On-Screen Menu Selecting Fan Mode [FAN MODE] Fan Mode is used to set the speed of the internal cooling fan. AUTO The built-in fans automatically run at a variable speed according to the internal temperature. HIGH The built-in fans run at a high speed. HIGH ALTITUDE The
  • NEC NP-P502H | Users Manual - Page 71
    4. Using On-Screen Menu Setting HDMI1, HDMI2, or HDBaseT [HDMI SETTINGS] Make the settings for each video level when connecting HDMI equipment and Ethernet/HDBaseT terminal. VIDEO LEVEL Select [AUTO] to automatically detect video level. If automatic detection may not work well, select [NORMAL] to
  • NEC NP-P502H | Users Manual - Page 72
    buttons on the projector cabinet and the remote control, powering on from PC Control command, AUTO POWER ON, Operation by User Supportware, Network service, Program Timer. Important: • When [NETWORK STANDBY] is selected, [AUTO POWER OFF] will turn in grey and be disabled and [0:10] will be selected
  • NEC NP-P502H | Users Manual - Page 73
    4. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON] When the projector is in Standby mode, applying a computer or HDMI signal from a computer connected to the COMPUTER IN input, HDMI1, or HDMI2 input will power on the projector and simultaneously project the
  • NEC NP-P502H | Users Manual - Page 74
    the Video source from the VIDEO IN terminal every time the projector is turned on. HDBaseT Projects the signal transmitted from the terminals supported HDBaseT. APPS Display the APPS MENU. NOTE: • [APPS] can not be detected when [AUTO] is selected. For projecting image from APPS, select [APPS
  • NEC NP-P502H | Users Manual - Page 75
    the 3D mode for the selected input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make right eye images displayed horizontally. Only the half of the horizontal resolution is supported TOP AND BOTTOM Selects this format for the TOP AND BOTTOM 3D image
  • NEC NP-P502H | Users Manual - Page 76
    [L/R INVERT] Change the setting if you have difficulty seeing 3D images. 4. Using On-Screen Menu NON-INVERT Normal setting. INVERT Changes the order of displaying the images for left eye and right eye. NOTE: • When [L/R INVERT] cannot be operated, the [L/R INVERT] screen will not be displayed
  • NEC NP-P502H | Users Manual - Page 77
    4. Using On-Screen Menu ❻ Menu Descriptions & Functions [INFO.] Displays the status of the current signal and lamp usage.This item has nine pages.The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LAMP LIFE
  • NEC NP-P502H | Users Manual - Page 78
    [SOURCE(1)] [RESOLUTION] [VERTICAL FREQUENCY] [SYNC POLARITY] [SOURCE(2)] [SIGNAL TYPE] [BIT DEPTH] [3D SIGNAL] [HDBaseT] [SIGNAL QUALITY] [LINK STATUS] [WIRED LAN] [IP ADDRESS] [GATEWAY] [WIRELESS LAN] [IP ADDRESS] [GATEWAY] [SSID] [SECURITY] [SIGNAL LEVEL] [VERSION(1)] [FIRMWARE] Version [VERSION
  • NEC NP-P502H | Users Manual - Page 79
    [LAMP HOURS USED], [FILTER HOURS USED], [TOTAL CARBON SAVINGS], [PROJECTOR NAME], [WIRED LAN], [WIRELESS LAN], [IMAGE EXPRESS UTILITY LITE], [NETWORK SERVICE], [DATE & TIME], [ADMINISTRATOR MODE], and [REMOTE DESKTOP CONNECTION]. Clearing Lamp Hour Meter [CLEAR LAMP HOURS] Resets the lamp clock back
  • NEC NP-P502H | Users Manual - Page 80
    . The projection distance range at which focusing is possible is 0.79 m (for a 30 model) to 14.19 m (for a 300 model). Install within this range. [P502H/P452H] Screen size (inch) 300 240 When zoom lever turned to wide When zoom lever turned to telescopic 200 180 150 120 100 80 60 40
  • NEC NP-P502H | Users Manual - Page 81
    [P502W/P452W] 5. Installation and Connections Screen size (inch) 300 240 When zoom lever turned to wide When zoom lever turned to telescopic 200 180 150 120 100 80 60 40 30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 (m) [Projection distance] When zoom lever With tilt feet tilted 4°
  • NEC NP-P502H | Users Manual - Page 82
    Tables of screen sizes and dimensions [P502H/P452H] Screen height Screen size (diagonal) Screen width Size (inches) 30 40 50 60 80 100 120 150 200 250 300 5. Installation and Connections Screen width (
  • NEC NP-P502H | Users Manual - Page 83
    projection position: Equal distance to the left and right from the center of the lens Vertical projection position: (see table below) [P502H/P452H] Lens center Approximately 81 to 86 mm Projection distance L Screen surface Lower edge of screen with 62% V Measurement +H Measurement -H Lower edge
  • NEC NP-P502H | Users Manual - Page 84
    and H "Horizontal" refers to the screen width. The lens shift range is expressed as a ratio of height and width, respectively. [P502H/P452H] Lens shifting range: Vertical direction: +62%, −0% Horizontal direction: ±25% 62%V 25%H 25%H Width of projected image 100%V [P502W/P452W] Lens shifting
  • NEC NP-P502H | Users Manual - Page 85
    Connections (Example) When using to project on a 150" screen [P502H/P452H] According to the "Table of screen sizes and dimensions" (→ page 71 you to enjoy a much larger image when a smaller space is required. Contact your NEC dealer if you need a mirror system. If you're using a mirror system and
  • NEC NP-P502H | Users Manual - Page 86
    used to connect to a computer. The HDMI cable is not enclosed with the projector. Please get ready a suitable cable for the connection. NOTE: Signals supported by Plug & Play (DDC2) COMPUTER IN analog Yes INPUT HDMI 1 IN digital Yes HDMI 2 IN digital Yes HDMI cable (not supplied) Use High Speed
  • NEC NP-P502H | Users Manual - Page 87
    the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle happen, restart your PC. • The COMPUTER video input terminals support Windows Plug and Play. • A Mac signal adapter (commercially available)
  • NEC NP-P502H | Users Manual - Page 88
    (VGA) (supplied) Computer cable (VGA) (not supplied) Stereo mini-plug audio cable (not supplied) NOTE: • The AUDIO OUT mini jack does not support Headphone terminal. • When audio equipment is connected, the projector speaker is disabled. • The signal output from the MONITOR OUT (COMP.) of this
  • NEC NP-P502H | Users Manual - Page 89
    . Input terminal SOURCE button on the projector cabinet Button on the remote control VIDEO IN VIDEO (VIDEO) NOTE: Refer to your VCR owner's manual for more information about your equipment's video output requirements. NOTE: An image may not be displayed correctly when a Video source is played
  • NEC NP-P502H | Users Manual - Page 90
    projector. Input terminal COMPUTER IN SOURCE button on the projector cabinet COMPUTER Button on the remote control (COMPUTER 1) NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements. 79
  • NEC NP-P502H | Users Manual - Page 91
    5. Installation and Connections Connecting HDMI Input You can connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the HDMI IN terminal of your projector. HDMI 1 IN HDMI 2 IN HDMI cable (not supplied) Use High Speed HDMI® Cable. Audio cable (not
  • NEC NP-P502H | Users Manual - Page 92
    VIDEO IN COMPUTER IN Computer cable (VGA) (supplied) Name, position, and direction of terminals are vary depending on camera model. Please check user's manual of your camera for details. Video cable (not supplied) • Select the source name for its appropriate input terminal after turning on the
  • NEC NP-P502H | Users Manual - Page 93
    the ports (it is not possible to connect both ports to the LAN). For controlling the projector by a HDBaseT transmitter whose control signal is not supported (or with which cannot connect the projector) or over the network, connect to the LAN port. At the same time, for controlling the projector
  • NEC NP-P502H | Users Manual - Page 94
    5. Installation and Connections Connecting to a Wireless LAN (Optional: NP05LM series) The USB Wireless LAN Unit also provides a wireless LAN connection. To use a wireless LAN connection, you are required to assign an IP address to the projector. Important: • If you use the projector with the USB
  • NEC NP-P502H | Users Manual - Page 95
    4. Mount the wireless LAN cover. (1)Insert the hook on the back of the cover into the groove in the projector and close the wireless LAN cover. (2)Turn the screw clockwise to tighten it. 5. Installation and Connections Groove Hook * To remove the USB Wireless LAN Unit, disconnect the power cord
  • NEC NP-P502H | Users Manual - Page 96
    5. Installation and Connections Example of wireless LAN connection To use a LAN connection, you are required to set the Wireless LAN settings on the projector menu. Select [SETUP] → [INSTALLATION] → [NETWORK SETTINGS]. (→ page 58). The network settings can also be selected from the APPS menu. PC
  • NEC NP-P502H | Users Manual - Page 97
    device sold commercially. Control signals (serial and LAN) and remote control signals (IR commands) from an external device are only supported when the projector's power is turned on. Connection example Computer (for control use) Remote control Example of a transmission device Ethernet
  • NEC NP-P502H | Users Manual - Page 98
    5. Installation and Connections TIP: • With the projector's Ethernet/HDBaseT port, remote control is not available when the projector is in the standby mode (serial communications is not available). (Remote control becomes available when the projector's power is on). The 2 (two) methods below can be
  • NEC NP-P502H | Users Manual - Page 99
    about each function on the APPS MENU is explained on our web site. Please search it by the model name of your projector. http://www.nec-display.com/dl/en/pj_manual/lineup.html APPS MENU screen display REMOTE DESKTOP CONNECTION VIEWER FOCUS Indicating the selected item. Surrounded in a yellow square
  • NEC NP-P502H | Users Manual - Page 100
    "Wireless Image Utility" from our web site and install it on these. (→ page 112) Miracast By wirelessly connecting the terminal units supporting the Miracast such as the Android with the projector, it enables the projector to project images transmitted from these terminals. Before connecting these
  • NEC NP-P502H | Users Manual - Page 101
    UTILITY. It also available for setting up a password to log in the ADMINISTRATOR MODE for the IMAGE EXPRESS UTILITY in the WEB SERVER functions. NETWORK SERVICE Set up various setting for the AMX, HTTP server, PJLink, Alert mail and CRESTRON. 90
  • NEC NP-P502H | Users Manual - Page 102
    6. APPS MENU TOOLS Set up for various features as the mouse, program timer, day and time, administrator mode and default APP. MOUSE A commercially available USB mouse can be used for operating the APPS MENU. Perform the set up for using it. PROGRAM TIMER Once day and time is set up, changing the
  • NEC NP-P502H | Users Manual - Page 103
    Express Utility Lite does not support "Meeting Mode" in Image Express Utility 2.0 supplied with our other models. Download Service and Operating Environment Please visit our website about operating environment and download service for each software: Visit URL: http://www.nec-display.com/dl/en/index
  • NEC NP-P502H | Users Manual - Page 104
    Projecting Your Computer's Screen Image from the Projector over a LAN (Image Express Utility Lite) Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM allows you to send the computer's screen image to the projector over a wired or wireless LAN. Image Express Utility Lite
  • NEC NP-P502H | Users Manual - Page 105
    enough space (about 100 MB) to install the program. 1. Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be agree, click "I agree." and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation
  • NEC NP-P502H | Users Manual - Page 106
    LAN. Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 82 , click "Start" → "All programs" → "NEC Projector UserSupportware" → "Image Express Utility Lite" → projector supports the movie streaming function. If the projector does not support the
  • NEC NP-P502H | Users Manual - Page 107
    SD cards if it is copied beforehand. This will eliminate the trouble of installing Image Express Utility Lite to your computer. 1. Copy Image approx. 7 MB) from the "IEU_Lite (removable-media)" folder in the supplied NEC Projector CD-ROM to the root directory of your removable media. 2. Insert your
  • NEC NP-P502H | Users Manual - Page 108
    Express Utility Lite for Mac on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM 2: Connect the projector to a LAN Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 82) and "Connecting to a Wireless
  • NEC NP-P502H | Users Manual - Page 109
    7. User Supportware ❸ Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite) The Geometric Correction Tool (GCT) function allows you to correct distortion of images projected even from an angle. What you can do with GCT • The GCT feature includes the following
  • NEC NP-P502H | Users Manual - Page 110
    4. Click the " "(Projection) icon and then the " button. "(Exit) 5. Click "Yes". 6. Start the Image Express Utility Lite again. 7. Click the " " (Picture) icon and then the " " button. 7. User Supportware The "4-point Correction" window will be displayed. 8. Click the "Start Correction" button
  • NEC NP-P502H | Users Manual - Page 111
    10.Drag the selected [ • ] mark to the point you wish to correct and drop it. • When you click somewhere within the project image area, the nearest [ • ] mark will go to the position where the mouse cursor is. 11.Repeat Step 9 and 10 to correct the distortion of the projected image. 7. User
  • NEC NP-P502H | Users Manual - Page 112
    (PC Control Utility Pro 4/ Pro 5) Using the utility software "PC Control Utility Pro 4" and "PC Control Utility Pro 5" included on the companion NEC Projector CD-ROM, the projector can be controlled from a computer over a LAN. PC Control Utility Pro 4 is a program compatible with Windows. (→ this
  • NEC NP-P502H | Users Manual - Page 113
    USER LICENSE AGREEMENT" carefully. 4 If you agree, click "I accept the terms in the license agreement" and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window. TIP: • Uninstalling
  • NEC NP-P502H | Users Manual - Page 114
    the projector to a LAN. Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 82) and "Connecting to Utility Pro 4 Click "Start" → "All programs" or "Programs" → "NEC Projector User Supportware" → "PC Control Utility Pro 4" → "PC Control Utility Pro
  • NEC NP-P502H | Users Manual - Page 115
    Install PC Control Utility Pro 5 on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM 7. Click "I accept the terms in the license agreement". Follow the instructions on the installer screens to complete the installation. Step 2: Connect the projector
  • NEC NP-P502H | Users Manual - Page 116
    Utility Pro 5 to the Trash icon. • The configuration file of PC Control Utility Pro 5 is located in "/Users//Application Data/NEC Projector User Supportware/PC Control Utility Pro 5". Viewing the Help of PC Control Utility Pro 5 • Displaying the Help file of PC Control Utility Pro
  • NEC NP-P502H | Users Manual - Page 117
    ) Using the utility software "Virtual Remote Tool" included on the companion NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed a LAN and a serial connection. USB connection is not supported by Virtual Remote Tool. • For update information on Virtual Remote Tool, visit our
  • NEC NP-P502H | Users Manual - Page 118
    as the background logo by using the image file (P502H/P452H: /Logo/NEC_logo2015_1920x1080.bmp, P502W/P452W: /Logo/NEC_logo2015_1280x800.bmp) inclulded on the supplied NEC Projector CD-ROM. TIP: • The projector's COMPUTER IN terminal supports DDC/CI (Display Data Channel Command Interface). DDC/CI is
  • NEC NP-P502H | Users Manual - Page 119
    . Read "END USER LICENSE AGREEMENT" carefully. 4 If you agree, click "I accept the terms in the license agreement" and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window. 108
  • NEC NP-P502H | Users Manual - Page 120
    Tool and click it. 4 Click "Uninstall/Change" or "Uninstall". • When the "User Account Control" windows is displayed, click "Continue". Follow the instructions on the screens to complete the uninstallation. Step 2: Connect the projector to the computer 1 Use the supplied computer cable (VGA) to
  • NEC NP-P502H | Users Manual - Page 121
    Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When for the first time, "Easy Setup" window will be displayed. Follow the instructions on the screens When "Easy Setup" is completed, the Virtual Remote Tool
  • NEC NP-P502H | Users Manual - Page 122
    Click "Help". The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click "Start" → "All programs" or "Programs" → "NEC Projector User Supportware" → "Virtual Remote Tool" → and then "Virtual Remote Tool Help" in this order. The Help screen will be displayed. 111
  • NEC NP-P502H | Users Manual - Page 123
    Wireless Image Utility software one for Android and another for iOS that can be downloaded from Google Play or App Store. For Android http://www.nec-display.com/dl/en/pj_android/wiu_for-android.html For iOS http://www
  • NEC NP-P502H | Users Manual - Page 124
    cover. Prevent the color wheel from dust and dirt accumulation. In this manual, call the intake vent filter "Filter (A)" and the color wheel filter If dust and dirt accumulates on the Filter (A), it may cause of trouble by overheat. Clean it periodically. Cleaning is not necessary for the Filter
  • NEC NP-P502H | Users Manual - Page 125
    1. Turn off the power supply and pull out the plug from the wall outlet. 2. Pinch the knob at the bottom of the filter case and pull it out. • If you put the projector upside down for cleaning as the illustration, please lay a mat as a cloth for protecting the cabinet top from damage. 8.
  • NEC NP-P502H | Users Manual - Page 126
    5. Set the cleaned Filter (A) onto the filter case. • Set the cut off part of the Filter (A) meeting with the knob part on the filter case. 8. Maintenance Knob Cut off 6. Insert the filter case to the projector cabinet. Make sure that the filter case is inserted in the correct orientation. 7.
  • NEC NP-P502H | Users Manual - Page 127
    8. Maintenance ❷ Cleaning the Lens • Turn off the projector before cleaning. • Do not scratch or mar the projection window as it is made of glass. • Use a blower or lens paper to clean the projection window, and be careful not to scratch or mar the glass surface. • Never use alcohol or glass lens
  • NEC NP-P502H | Users Manual - Page 128
    8. Maintenance ❸ Cleaning the Cabinet Turn off the projector, and unplug the projector before cleaning. • Use a dry soft cloth to wipe dust off the cabinet. If heavily soiled, use a mild detergent. • Never use strong detergents or solvents such as alcohol or thinner. • For cleaning the vents or the
  • NEC NP-P502H | Users Manual - Page 129
    , specify your lamp type. Replacement lamp: NP39LP: P502H/P502W NP38LP: P452H/P452W The replacement lamp comes with filters. Replace the lamp and the the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement. *NOTE: This message will be displayed under the
  • NEC NP-P502H | Users Manual - Page 130
    To replace the lamp and the Filter (B): 1. Remove the lamp cover. (1)Loosen the lamp cover screw • The lamp cover screw is not removable. 8. Maintenance (2)Push and slide the lamp cover off. a b 2. Pull out the filter case. Pinch the filter case handle and pull it in the arrow indicated
  • NEC NP-P502H | Users Manual - Page 131
    (2)Vacuum off accumulated dust and dirt on inside and outside of the filter case. (3)Fix a new Filter (B) onto the filter case. 4. Remove the lamp housing. (1)Loosen the three screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. • The three screws are
  • NEC NP-P502H | Users Manual - Page 132
    5. Install a new lamp housing. (1)Insert a new lamp housing until the lamp housing is plugged into the socket. (2)Push the top center of the lamp housing to secure it. 8. Maintenance (3)Secure it in place with the three screws. • Be sure to tighten the screws. 6. Insert for resetting the filter
  • NEC NP-P502H | Users Manual - Page 133
    7. Reattach the lamp cover. (1)Slide the lamp cover back until it snaps into place. (2)Tighten the screw to secure the lamp cover. • Be sure to tighten the screw. 8. Maintenance a b This completes the lamp and Filter (B) replacement. Go on to the Filter (A) replacement. NOTE: When you continue to
  • NEC NP-P502H | Users Manual - Page 134
    To replace the Filter (A): 8. Maintenance NOTE: • Before replacing the filters, wipe off dust and dirt from the projector cabinet. • The projector is precision equipment. Keep out dust and dirt during filter replacement. • Do not wash the filters with soap and water. Soap and water will damage the
  • NEC NP-P502H | Users Manual - Page 135
    4. Fix a new Filter (A) onto the filter case. • Set the cut off part of the Filter (A) meeting with the knob part on the filter case. 8. Maintenance Knob Cut off 5. Insert the Filter case to the projector cabinet. Make sure that the filter case is inserted in the correct orientation. This
  • NEC NP-P502H | Users Manual - Page 136
    9. Appendix ❶ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the on the projector again. Even though the lamp is not turned on, ask your dealer or service personnel for repair. Both the built-in wired LAN and the wireless LAN cannot be connected
  • NEC NP-P502H | Users Manual - Page 137
    9. Appendix Over-Temperature Protection If the projector inside temperature gets too high, the lamp will be turned off automatically and the status indicator will start to blink (2-cycle On and Off). Should this happen, do the following: • Unplug the power cord after the cooling fans stop. • Move
  • NEC NP-P502H | Users Manual - Page 138
    page 125.) Problem Check These Items refer to the user guide accompanied with your computer or graphics card, or contact the support center for your computer not liable for any trouble and failure caused by this installation. • Signals may not be supported depending on the HDBaseT transmission
  • NEC NP-P502H | Users Manual - Page 139
    resolution you are trying to display is supported by the projector. (→ page 136) • Adjust the computer image manually with the [HORIZONTAL]/[VERTICAL] in function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations
  • NEC NP-P502H | Users Manual - Page 140
    9. Appendix Model name NP-P502H NP-P502W NP-P452H NP-P452W Method 1 Chip VESA standards Main adjustment functions Manual zoom, manual focus, manual lens shift, input signal switching compatible LipSync compatible, HDCP compatible (*4), Supports 3D Audio input HDMI: Sampling frequency
  • NEC NP-P502H | Users Manual - Page 141
    NP-P502H NP-P502W NP-P452H Deep Color (color depth): Support 8/10/12 bits Colorimetry: Support RGB, YCbCr444 and YCbCr422 Support LipSync , HDCP (*4), 3D Sampling frequency: 32/44.1/48 kHz Sampling bit: 16/20/24 bit Stereo mini Jack × 1 1 for USB memory 1 for service RJ-45 × 1, Supports
  • NEC NP-P502H | Users Manual - Page 142
    ❸ Cabinet Dimensions Unit: mm (inch) 9. Appendix 306 (12) 302 (11.9) Lens center 362 (14.3) 91 (3.6) 139 (5.5) 129 (5.1) 81 (3.2) 68 (2.7) 150 (5.9) 130 (5.1) 5 (0.2) 175 (6.9) 200 (7.9) 131
  • NEC NP-P502H | Users Manual - Page 143
    ❹ Attaching the Optional Cable Cover (NP09CV) After finishing connections, attach the supplied cable cover to properly hide the cables. 9. Appendix CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting
  • NEC NP-P502H | Users Manual - Page 144
    Removing the cable cover 1. Loosen the cable cover screws until the Phillips screwdriver goes into a freewheeling condition and remove the cover. • When suspended from the ceiling, hold so that the cable cover does not drop. • The screws cannot be removed. 9. Appendix 133
  • NEC NP-P502H | Users Manual - Page 145
    9. Appendix ❺ Pin assignments and signal names of main terminals COMPUTER IN Terminal (Mini D-Sub 15 Pin) Connection and signal level of each pin 11 12 13 14 15 6 7 8 9 10 1 23 45 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
  • NEC NP-P502H | Users Manual - Page 146
    Ethernet/HDBaseT/LAN Port (RJ-45) 12345678 Pin No. 1 2 3 4 5 6 7 8 Signal TxD+/HDBT0+ TxD−/HDBT0− RxD+/HDBT1+ Disconnection/HDBT2+ Disconnection/HDBT2− RxD−/HDBT1− Disconnection/HDBT3+ Disconnection/HDBT3− USB Port (Type A) 1 2 3 4 Pin No. 1 2 3 4 VBUS D− D+ Grounding Signal PC CONTROL Port
  • NEC NP-P502H | Users Manual - Page 147
    /59.94/60 *1 Native resolution on 1080p model (NP-P502H/NP-P452H) *2 Native resolution on WXGA model (NP-P502W/NP-P452W) *3 The projector may fail to display these *4 WXGA MODE: OFF *5 WXGA MODE: ON *6 120Hz signals are supported for Frame Sequential only. NOTE: • An image with higher or lower
  • NEC NP-P502H | Users Manual - Page 148
    ❼ PC Control Codes and Cable Connection PC Control Codes Function POWER ON POWER OFF INPUT SELECT COMPUTER INPUT SELECT HDMI1 INPUT SELECT HDMI2 INPUT SELECT VIDEO INPUT SELECT APPS INPUT SELECT HDBaseT PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF Code Data 02H 00H 00H 00H 00H 02H
  • NEC NP-P502H | Users Manual - Page 149
    page during the software update. It disables the computer for displaying the web page correctly. 1. Access to the software download support page in our web site. URL: http://www.nec-display.com/dl/en/pj_soft/lineup.html 2. Check if the software installed on the projector in use is updated. • You
  • NEC NP-P502H | Users Manual - Page 150
    NOTE: • During the software update, pay attention to the follows: - Do not turn off the AC Power for the projector. - Do not reload or move the web page. - Do not close the web page. • When software update is completed properly, the below will be displayed on: 1. UPLOADING THE UPDATE FILE: COMPLETED
  • NEC NP-P502H | Users Manual - Page 151
    service personnel, check the following list to be sure repairs are needed also by referring to the "Troubleshooting" section in your user's manual. This checklist below will help us solve your problem . □ Input source's resolution and frequency are supported by the projector. □ Image is too dark
  • NEC NP-P502H | Users Manual - Page 152
    In the space below please describe your problem in detail. 9. Appendix Information on application and environment Native resolution: Refresh rate: Video adapter: Other: DVD player Signal cable NEC standard or other manufacturer's cable? Model number: Length: inch/m Distribution amplifier
  • NEC NP-P502H | Users Manual - Page 153
    .com, click on support center/register product and submit your completed form online. Upon receipt, we will send a confirmation letter with all the details you will need to take advantage of fast, reliable warranty and service programs from the industry leader, NEC Display Solutions of America
  • NEC NP-P502H | Users Manual - Page 154
    © NEC Display Solutions, Ltd. 2015 7N952321
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Projector
P502H/P452H
P502W/P452W
User’s Manual
Model No.
NP-P502H, NP-P452H, NP-P502W, NP-P452W