NEC NP-P502HL Users Manual

NEC NP-P502HL Manual

Get NEC NP-P502HL PDF manuals and user guides View all NEC NP-P502HL manuals
Add to My Manuals
Save this manual to your list of manuals

NEC NP-P502HL manual content summary:

  • NEC NP-P502HL | Users Manual - Page 1
    Projector P502HL/P502WL User's Manual Model No. NP-P502HL, NP-P502WL
  • NEC NP-P502HL | Users Manual - Page 2
    . • App Store is a service mark of Apple Inc. • manual pdf" inside the "about GPL&LGPL" folder on the supplied CDROM. NOTES (1) The contents of this user's manual manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), NEC
  • NEC NP-P502HL | Users Manual - Page 3
    this manual carefully before using your NEC projector and keep the manual handy ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the provided. The information should be read carefully to avoid problems. WARNING: TO PREVENT FIRE OR SHOCK, DO NOT
  • NEC NP-P502HL | Users Manual - Page 4
    specified by NEC Display Solutions of America, Inc. in this manual. Failure to Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire , the ceiling must be strong enough to support the projector and the installation must be in accordance with
  • NEC NP-P502HL | Users Manual - Page 5
    objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel. • Do not place any objects on top of the projector. • Do not touch the power plug during a thunderstorm
  • NEC NP-P502HL | Users Manual - Page 6
    instructions described in this user's manual. - If the projector has been dropped or the cabinet has been damaged. - If the projector exhibits a distinct change in performance, indicating a need for service , heat, or take apart batteries. • Do not throw batteries into fire. • If you will not be
  • NEC NP-P502HL | Users Manual - Page 7
    multiple laser diodes is equipped in the product as the light source. 2. These laser diodes are sealed in the light module. No maintenance or service is of the device. • Blue laser diodes: Wave length 455 nm, Output power 120 W • Do not look into the lens while the projector is on. Serious damage to
  • NEC NP-P502HL | Users Manual - Page 8
    • The labels are stuck on the below indicated position. Label 1 Label 1: Label 2 Important Information Label 2: vi
  • NEC NP-P502HL | Users Manual - Page 9
    Important Information About Copyright of original projected pictures: Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion
  • NEC NP-P502HL | Users Manual - Page 10
    Factory preset: 1 hour) To control the projector from an external device, select [OFF] found in the user's manual included with your LCD shutter distance of 2 m/7 feet or greater between the screen and a user. Viewing 3D images from too close a distance nec-display.com/global/support/index.html viii
  • NEC NP-P502HL | Users Manual - Page 11
    2 General...2 Light source · Brightness 2 Installation...2 Videos...2 Network...2 Energy-saving...3 About this user's manual 3 ❸ Part Names of the Projector 4 Front...4 Mounting the lens cap strap 4 Rear...5 Controls/Indicators...6 Terminal Panel Features 7 ❹ Part Names of the Remote Control
  • NEC NP-P502HL | Users Manual - Page 12
    [SECURITY 30 ❻ Viewing 3D Images...33 LCD shutter eyeglasses (recommended 33 Steps for viewing 3D images on the projector 33 Troubleshooting on viewing 3D images 36 4. Using On-Screen Menu 37 ❶ Using the Menus...37 Menu Elements...38 ❷ List of Menu Items...39 ❸ Menu Descriptions & Functions
  • NEC NP-P502HL | Users Manual - Page 13
    Included on CD-ROM 92 ❷ Projecting Your Computer's Screen Image from the Projector over a LAN (Image Express Utility Lite 93 Starting Image Express Utility Lite the Cabinet 114 9. Appendix...115 ❶ Troubleshooting...115 Indicator Messages 115 Common Problems & Solutions 117 If there is no
  • NEC NP-P502HL | Users Manual - Page 14
    Infomation (For North America: 7N8N6171) (For Other countries than North America: 7N8N6171 and 7N8N6181) • Quick Setup Guide (7N8N6191)/ (7N8N6201) NEC Projector CD-ROM User's manual (PDF) and the utility software (7N952241) For North America only Limited warranty For customers in Europe: You will
  • NEC NP-P502HL | Users Manual - Page 15
    stored in the enclosed NEC Projector CD-ROM (Image Express Utility Lite (For Windows/ OS X),Virtual Remote Tool, PC Control Utility Pro 4 (for Windows ) and PC Control Utility Pro 5 (for OS X)) can be used. • CRESTRON ROOMVIEW compatible This projector supports CRESTRON ROOMVIEW, allowing multiple
  • NEC NP-P502HL | Users Manual - Page 16
    AC) • "ECO MODE" for low power consumption and "CARBON METER" display The projector is equipped with a "LIGHT MODE" for reducing power consumption during use. Furthermore, now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find
  • NEC NP-P502HL | Users Manual - Page 17
    ❸ Part Names of the Projector Front Lens shift cover (→ page 17) Zoom Lever (→ page 19) Lens Focus Ring (→ page 19) Lens Cap Intake Vent (→ page 20) Lens cap mount hole 2. Insert the knot into the strap mount hole (large) on the bottom of the projector, then press it into the narrow (small) hole. 4
  • NEC NP-P502HL | Users Manual - Page 18
    opening Attach an anti-theft device. The security chain opening accepts security wires or chains up to 0.18 inch/4.6 mm in diameter. * This security slot supports the MicroSaver® Security System. 5
  • NEC NP-P502HL | Users Manual - Page 19
    Controls/Indicators 2 34 5 6 8 1. (POWER) Button (→ page 12, 24) 2. POWER Indicator (→ page 11, 12, 24, 115) 3. STATUS Indicator (→ page 115) 4. LIGHT Indicator (→ page 115) 5. ECO Button (→ page 28) 6. SOURCE Button (→ page 14) 7. AUTO ADJ. Button (→ page 23) 8. MENU Button (→ page 37) 9
  • NEC NP-P502HL | Users Manual - Page 20
    ) 14. PC CONTROL [PC CONTROL] Port (D-Sub 9 Pin) (→ page 127) Use this port to connect a PC or control system. This enables you to control the projector using serial communication protocol. If you are writing your own program, typical PC control codes are on page 127. 15
  • NEC NP-P502HL | Users Manual - Page 21
    page 48) 13. USB-B Button 32. FOCUS/ZOOM Button (This button does not work in this (This button does not work in this series of projectors) series of projectors) 14. APPS Button (→ page 14, 88) 33. HELP Button (→ page 65) 15. ID SET Button (→ page 56) 16. Numeric Keypad Button/ CLEAR Button
  • NEC NP-P502HL | Users Manual - Page 22
    humidity. • Do not short, heat, or take apart batteries. • Do not throw batteries into fire. • If you will not be using the remote control for a sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet. • The projector will not respond
  • NEC NP-P502HL | Users Manual - Page 23
    onto the screen. ❶ Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 11) Step 2 • Turning on the projector (→ page 12) Step 3 • Selecting a source (→ page 14) Step 4 • Adjusting the picture size and position (→ page 16) • Correcting keystone distortion
  • NEC NP-P502HL | Users Manual - Page 24
    connection to a computer. For information about other connections, see "5. Installation and Connections" on page 73. Connect the computer cable (VGA) between the projector's COMPUTER IN terminal and the computer's port (mini D-Sub 15 Pin). Turn two thumb screws of both terminals to fix the computer
  • NEC NP-P502HL | Users Manual - Page 25
    at the lens. 1. Remove the lens cap. With the lens cap's stopper pressed up, pull forward and off. Stopper 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator lights blue and the image is projected on the screen. TIP: • When
  • NEC NP-P502HL | Users Manual - Page 26
    2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 30 menu languages. To select a menu language, follow
  • NEC NP-P502HL | Users Manual - Page 27
    Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once. The projector will search for the available input source and display it. The input source will change as follows
  • NEC NP-P502HL | Users Manual - Page 28
    2. Projecting an Image (Basic Operation) Selecting Default Source You can so that it will be displayed each time the projector is turned on. 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button twice to select [SETUP] and the ▼ button or the ENTER
  • NEC NP-P502HL | Users Manual - Page 29
    ] (→ page 19) Adjusting the projected image's height and horizontal tilt [Tilt foot] (→ page 20) Correcting the keystone distortion [Keystone]* (→ page 21) * To perform keystone correction manually, see "6. Correcting Keystone Distortion [KEYSTONE]" on page 21. 16
  • NEC NP-P502HL | Users Manual - Page 30
    Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) CAUTION Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them. 1. Open the lens shift cover. Open with the
  • NEC NP-P502HL | Users Manual - Page 31
    shift cover. Insert the cover's 2 (two) hooks into the grooves in the projector, then close the cover. Hook Groove TIP: • The diagram below shows the , see page 71. [P502HL] 25%H 25%H Width of projected image 62%V [P502WL] 100%V 25%H 100%H 25%H 59%V 28%H 28%H Height of projected image
  • NEC NP-P502HL | Users Manual - Page 32
    Focus Use the FOCUS ring to obtain the best focus. Focus ring 2. Projecting an Image (Basic Operation) Zoom Turn the zoom lever clockwise and counterclockwise. Zoom lever 19
  • NEC NP-P502HL | Users Manual - Page 33
    Keystone Distortion [KEYSTONE]" (→ page 21). • The tilt feet can be lengthened by a maximum of 20 mm. • The tilt feet can be used to tilt the projector by a maximum of 4°. Up Down Tilt foot NOTE: • Do not lengthen the tilt feet any more than 20 mm/0.8". Doing so will make the tilt
  • NEC NP-P502HL | Users Manual - Page 34
    of the projected image are parallel. 1. When APPS is not selected as source and the menu is not displayed on, press the ▼ button on the projector cabinet. The Keystone screen will be displayed on the screen. • Press the KEYSTONE button when using the remote control. • See page 22 for [RESET
  • NEC NP-P502HL | Users Manual - Page 35
    2. Projecting an Image (Basic Operation) 4. Press the ▲ button to select [HORIZONTAL] and then use the ◀ or ▶ so that the top and bottom sides of the projected image are parallel. • Adjust the horizontal keystone distortion. 5. Repeat steps 2 and 4 to correct keystone distortion. 6. After completing
  • NEC NP-P502HL | Users Manual - Page 36
    signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE] manually. (→ page 46, 47) ❽ Turning Up or Down Volume Sound level from be adjusted. TIP: When no menus appear, the ◀ and ▶ buttons on the projector cabinet work as a volume control. NOTE: • Volume control is not available with
  • NEC NP-P502HL | Users Manual - Page 37
    remains to run for a while. When the cooling fan stops to run, the projector will go into the STANDBY mode. When in standby mode, the POWER indicator will projected and the cooling fan is rotating. Doing so could deteriorate the projector's AC IN terminal or the power plug's contact. Do not shut
  • NEC NP-P502HL | Users Manual - Page 38
    ❿ When Moving the Projector Preparation: Make sure that the projector is turned off. 2. Projecting an Image (Basic Operation) 1. If the separately sold cable cover is mounted, remove it. (→ page 122) 2. Unplug the power cord. 3. Disconnect
  • NEC NP-P502HL | Users Manual - Page 39
    3. Convenient Features ❶ Turning off the Image and Sound Press the AV-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. NOTE: • Even though the image is turned off, the menu still remains on the screen. ❷ Freezing a Picture Press the
  • NEC NP-P502HL | Users Manual - Page 40
    ❸ Magnifying a Picture You can enlarge the picture up to four times. NOTE: • The maximum magnification may be less than four times depending on the signal. To do so: 1. Press the D-ZOOM (+) button to magnify the picture. To move the magnified image, use the or ▶ button. 3. Convenient Features 2.
  • NEC NP-P502HL | Users Manual - Page 41
    control to display [ECO MODE] screen. 2. Use the ▼▲ buttons to select, then press the ENTER button. The [ECO MODE] selection screen turns off and the projector switches to the selected mode. • When in the [ECO MODE], the LIGHT indicator lights green. NOTE: • The [ECO MODE] can be changed by using
  • NEC NP-P502HL | Users Manual - Page 42
    Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector's [ECO MODE] is set to [ECO1] or [ECO2]. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and
  • NEC NP-P502HL | Users Manual - Page 43
    using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image. • The [SECURITY] setting cannot be cancelled by using the [RESET] of the
  • NEC NP-P502HL | Users Manual - Page 44
    the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button. The projector will be turned on and display a message to the effect that the projector is locked. 2. Press the MENU button. 3. Type in the correct keyword and
  • NEC NP-P502HL | Users Manual - Page 45
    To disable the SECURITY function: 3. Convenient Features 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen
  • NEC NP-P502HL | Users Manual - Page 46
    3D images. • Allow a distance of 2 m/7 feet or greater between the screen and a user. Viewing 3D images from too close a distance can strain your eyes. • use the projector to display the image. 4. Put on your LCD shutter eyeglasses to view 3D images. Also refer to the user's manual accompanied with
  • NEC NP-P502HL | Users Manual - Page 47
    3D images [HDMI1/HDMI2/COMPUTER/VIDEO/ HDBaseT] This function switches the 3D mode between ON and OFF for each input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make sure that [3D] is displayed in the top right of the screen after the
  • NEC NP-P502HL | Users Manual - Page 48
    or conditions such as the ambient brightness, screen size or viewing distance, the LCD shutter eyeglasses may fail to receive synch signals, terminal of the projector. NOTE: • Use an active shutter 3D eyewear (compliance with VESA) • Check the operating conditions described in the user manual of the
  • NEC NP-P502HL | Users Manual - Page 49
    Troubleshooting on viewing 3D images If images will not be displayed in 3D or 3D images appear as 2D, check the following table. Also refer to the user's manual distance between the viewer and the screen is too far. • Move closer to the screen until the viewer gets 3D images. • Or use the projector
  • NEC NP-P502HL | Users Manual - Page 50
    display the submenu window. 6. Adjust the level or turn the selected item on or off by using the buttons on the remote control or the projector cabinet. Changes are stored until adjusted again. 7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the
  • NEC NP-P502HL | Users Manual - Page 51
    . ECO mode symbol Indicates ECO MODE is set. Key Lock symbol Indicates the [CONTROL PANEL LOCK] is enabled. Thermometer symbol Indicates the projector is in the state of the [FORCED ECO MODE]. Wireless symbol Indicate the wireless LAN connection is enabled. Menu mode Indicate the [ADVANCED
  • NEC NP-P502HL | Users Manual - Page 52
    4. Using On-Screen Menu ❷ List of Menu Items Some menu items are not available depending on the input source. The below listed menu items are on the advanced menu. The mark (B) is added to the items on the basic menu. Refer to 88 pages about the APPS MENU. Menu Item SOURCE ADJUST SETUP HDMI1
  • NEC NP-P502HL | Users Manual - Page 53
    3D GLASSES FORMAT L/R INVERT 3D L/R INVERT 3D GLASSES FORMAT L/R INVERT Default Options COLOR COLOR, MONOCHROME ON OFF, ON ON OFF, ON AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC BLUE BLUE, BLACK, LOGO ON OFF, ON AUTO AUTO, DESKTOP FRONT, CEILING REAR, DESKTOP REAR, CEILING
  • NEC NP-P502HL | Users Manual - Page 54
    (1) (B) FIRMWARE DATA VERSION(2) (B) FIRMWARE2 OTHERS (B) PROJECTOR NAME HOST NAME MODEL NO. SERIAL NUMBER LAN UNIT PAL60, SECAM 8[bits], 10[bits], 12[bits] FULL, ENHANCED, DEFAULT SUPPORTED, NOT SUPPORTED NORMAL, WARNING, ABNORMAL HDBaseT, ETHERNET, LOW POWER, DISCONNECT NO LINK, HDBaseT
  • NEC NP-P502HL | Users Manual - Page 55
    , select [COMPUTER]. VIDEO Selects what is connected to your VIDEO input-VCR, DVD player or document camera. HDBaseT Projects the signal transmitted from the terminals supported HDBaseT. (→ page 80, 81) APPS Display the APPS MENU or the function in the APPS MENU that was used last time. 42
  • NEC NP-P502HL | Users Manual - Page 56
    4. Using On-Screen Menu ❹ Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are seven factory presets optimized for various types of images. You can
  • NEC NP-P502HL | Users Manual - Page 57
    [DETAIL SETTINGS] 4. Using On-Screen Menu Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT
  • NEC NP-P502HL | Users Manual - Page 58
    [CONTRAST] Adjusts the intensity of the image according to the incoming signal. 4. Using On-Screen Menu [BRIGHTNESS] Adjusts the brightness level or the back raster intensity. [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies
  • NEC NP-P502HL | Users Manual - Page 59
    [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. 4. Using On-Screen Menu CLOCK Use this item to fine tune the computer image or to remove any vertical banding that
  • NEC NP-P502HL | Users Manual - Page 60
    Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. 4. Using On-Screen Menu - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and
  • NEC NP-P502HL | Users Manual - Page 61
    the ratio of width to height of a projected image. The projector automatically determines the incoming signal and displays it in its appropriate ratio. • This table shows typical resolutions and aspect ratios that most computers support. Resolution VGA 640 × 480 SVGA 800 × 600 XGA 1024 × 768
  • NEC NP-P502HL | Users Manual - Page 62
    ratio is converted from 16:9 to 4:3. Turning on Noise Reduction [NOISE REDUCTION] This function allows you to select the level of noise reduction. The projector is set to the optimized level for each signal at the factory. Select your preference item for your signal when video noise is noticeable
  • NEC NP-P502HL | Users Manual - Page 63
    SETUP] [GENERAL] Correcting Keystone Distortion Manually [KEYSTONE] You can correct horizontal or vertical keystone manually. [HORIZONTAL] and [VERTICAL] values will be overwritten. They will not be deleted even when the projector is turned off. • Using [KEYSTONE] correction can cause the image to
  • NEC NP-P502HL | Users Manual - Page 64
    correction in applications where the screen material is not white. [LIGHT MODE] Adjusting the energy savings settings and the brightness of each projector in multi-screen projection. For energy savings settings, see page 28 "4 Changing Eco Mode/Checking Energy-Saving Effect". ECO MODE ADJUST OFF
  • NEC NP-P502HL | Users Manual - Page 65
    projector does not support PROJECTOR WILL TURN OFF WITHIN 3 MINUTES] message will be displayed on the bottom of the screen. Display the tools menu [TOOLS] This function display the tools menu. (→ page 91) Selecting Menu Language [LANGUAGE] You can choose one of 30 languages for on-screen instructions
  • NEC NP-P502HL | Users Manual - Page 66
    is pressed. Selecting Menu Display Time [DISPLAY TIME] This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the factory preset
  • NEC NP-P502HL | Users Manual - Page 67
    rear projection, desktop rear projection, and ceiling front projection. AUTO When the light module is turned ON, the inner sensor of the projector detects its installation state either DESK FRONT or CEILING FRONT and then switch its projection method DESKTOP FRONT CEILING REAR DESKTOP REAR
  • NEC NP-P502HL | Users Manual - Page 68
    sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The default is 38400 bps. On or Off Remote Sensor [REMOTE SENSOR] Set the remote control sensors on the projector's front and rear panels and the HDBaseT remote control sensor. The options are: ALL
  • NEC NP-P502HL | Users Manual - Page 69
    the CONTROL ID setting. NOTE: • When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the CONTROL ID function. (In this case the buttons on the projector cabinet can be used.) • Your setting will not be affected even when [RESET
  • NEC NP-P502HL | Users Manual - Page 70
    -Screen Menu Using Test Pattern [TEST PATTERN] Displays the test pattern for adjusting distortion on the screen and the focus at the time of the projector setup. Once the [TEST PATTERN] on the onscreen menu is selected, the pattern for adjustment will be displayed on. If you find distortion on the
  • NEC NP-P502HL | Users Manual - Page 71
    automatically run at a variable speed according to the internal temperature. HIGH The built-in fans run at a high speed. Select this option when using the projector at altitudes approximately 5500 feet/1700 meters or higher. NOTE: • It is recommended that you select High speed mode if you use the
  • NEC NP-P502HL | Users Manual - Page 72
    4. Using On-Screen Menu Setting HDMI1, HDMI2, or HDBaseT [HDMI SETTINGS] Make the settings for each video level when connecting HDMI equipment and Ethernet/HDBaseT terminal. VIDEO LEVEL Select [AUTO] to automatically detect video level. If automatic detection may not work well, select [NORMAL] to
  • NEC NP-P502HL | Users Manual - Page 73
    the following buttons, terminals, and features will work: POWER button on the projector cabinet and the remote control, powering on from PC Control command, AUTO POWER ON, Operation by User Supportware, Network service, Program Timer. Important: • When [NETWORK STANDBY] is selected, [AUTO POWER OFF
  • NEC NP-P502HL | Users Manual - Page 74
    .) terminal, AUDIO OUT terminal, LAN functions, Mail Alert function, DDC/CI (Virtual Remote Tool) 2. AUTO POWER OFF (Factory preset: 1 hour) To control the projector from an external device, select [OFF] for [AUTO POWER OFF]. NOTE: • When [1:00] is selected for [AUTO POWER OFF], you can enable the
  • NEC NP-P502HL | Users Manual - Page 75
    is turned on. VIDEO Displays the Video source from the VIDEO IN terminal every time the projector is turned on. HDBaseT Projects the signal transmitted from the terminals supported HDBaseT. APPS Display the APPS MENU. NOTE: • [APPS] can not be detected when [AUTO] is selected. For projecting
  • NEC NP-P502HL | Users Manual - Page 76
    the 3D mode for the selected input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make right eye images displayed horizontally. Only the half of the horizontal resolution is supported TOP AND BOTTOM Selects this format for the TOP AND BOTTOM 3D image
  • NEC NP-P502HL | Users Manual - Page 77
    [L/R INVERT] Change the setting if you have difficulty seeing 3D images. 4. Using On-Screen Menu NON-INVERT Normal setting. INVERT Changes the order of displaying the images for left eye and right eye. NOTE: • When [L/R INVERT] cannot be operated, the [L/R INVERT] screen will not be displayed
  • NEC NP-P502HL | Users Manual - Page 78
    ADDRESS] [GATEWAY] [WIRELESS LAN] [IP ADDRESS] [GATEWAY] [SSID] [SECURITY] [SIGNAL LEVEL] [VERSION(1)] [FIRMWARE] Version [VERSION(2)] [FIRMWARE2] Version [OTHERS] [PROJECTOR NAME] [MODEL NO.] [LAN UNIT TYPE] [HORIZONTAL FREQUENCY] [SYNC TYPE] [SCAN TYPE] [VIDEO TYPE] [VIDEO LEVEL] [OPERATION MODE
  • NEC NP-P502HL | Users Manual - Page 79
    PORT], [SECURITY], [COMMUNICATION SPEED], [CONTROL ID], [STANDBY MODE], [FAN MODE], [LIGHT HOURS USED], [TOTAL CARBON SAVINGS], [PROJECTOR NAME], [WIRED LAN], [WIRELESS LAN], [IMAGE EXPRESS UTILITY LITE], [NETWORK SERVICE], [DATE & TIME], [ADMINISTRATOR MODE], and [REMOTE DESKTOP CONNECTION]. 66
  • NEC NP-P502HL | Users Manual - Page 80
    of the screen. Use this to see whether or not enough height can be provided from the projector to the ceiling and for installing the screen. The diagram shows the projection distance when the projector is installed horizontally. The projected image can be moved up and down, left and right using the
  • NEC NP-P502HL | Users Manual - Page 81
    P502WL] Screen height from the center of the projector lens Screen size 5. Installation and Connections (inch) 300 240 When zoom lever turned to wide When zoom lever turned to telescopic 200 180 150 120 100 80 60 40 30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 (m) [Projection distance
  • NEC NP-P502HL | Users Manual - Page 82
    screen sizes and dimensions [P502HL] Screen height Screen size (diagonal) Screen width Size (inches) 30 40 50 60 80 100 120 150 200 250 300 [P502WL] Screen height Screen size (diagonal) Screen width Size (inches) 30 40 50 60 80 100 120 150 200 250 300 5. Installation and Connections Screen
  • NEC NP-P502HL | Users Manual - Page 83
    projector is used on a desktop. Horizontal projection position: Equal distance 50 60 80 100 120 150 200 250 300 Throw distance L (m) Wide Tele 0.79 1.39 1.07 +36.2 −186.8 - +43.4 [P502WL] Lens center Approximately 92 to 97 mm Projection distance L Screen surface Lower edge of screen with
  • NEC NP-P502HL | Users Manual - Page 84
    5. Installation and Connections Lens shifting range This projector is equipped with a lens shift function (→ page 17 −0% Horizontal direction: ±25% 62%V 25%H 25%H Width of projected image 100%V [P502WL] Lens shifting range: Vertical direction: +59%, −0% Horizontal direction: ±28% 25%H 100%H
  • NEC NP-P502HL | Users Manual - Page 85
    ≈ 32.7"/83 cm, to the right approximately 32.7"/83 cm. [P502WL] According to the "Table of screen sizes and dimensions" (→ page projector. Reflecting the Image Using a mirror to reflect your projector's image enables you to enjoy a much larger image when a smaller space is required. Contact your NEC
  • NEC NP-P502HL | Users Manual - Page 86
    Computer cables and HDMI can be used to connect to a computer. The HDMI cable is not enclosed with the projector. Please get ready a suitable cable for the connection. NOTE: Signals supported by Plug & Play (DDC2) COMPUTER IN analog Yes INPUT HDMI 1 IN digital Yes HDMI 2 IN digital Yes HDMI
  • NEC NP-P502HL | Users Manual - Page 87
    NEC ISS-6020 switcher. NOTE: An image may not be displayed correctly when a Video source is played back via a commercially available scan converter. This is because the projector happen, restart your PC. • The COMPUTER video input terminals support Windows Plug and Play. • A Mac signal adapter (commercially
  • NEC NP-P502HL | Users Manual - Page 88
    cable (VGA) (supplied) NOTE: • The AUDIO OUT mini jack does not support Headphone terminal. • When audio equipment is connected, the projector speaker is disabled. • The signal output from the MONITOR OUT (COMP.) of this projector is for projecting image on exclusive one display. • When no signal
  • NEC NP-P502HL | Users Manual - Page 89
    name for its appropriate input terminal after turning on the projector. Input terminal SOURCE button on the projector cabinet Button on the remote control VIDEO IN VIDEO (VIDEO) NOTE: Refer to your VCR owner's manual for more information about your equipment's video output requirements. NOTE
  • NEC NP-P502HL | Users Manual - Page 90
    name for its appropriate input terminal after turning on the projector. Input terminal COMPUTER IN SOURCE button on the projector cabinet COMPUTER Button on the remote control (COMPUTER 1) NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output
  • NEC NP-P502HL | Users Manual - Page 91
    connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the HDMI IN terminal of your projector. HDMI 1 IN HDMI 2 IN HDMI cable (not supplied) Use High Speed HDMI® Cable. Audio cable (not supplied) • Select the source name for its appropriate input
  • NEC NP-P502HL | Users Manual - Page 92
    of terminals are vary depending on camera model. Please check user's manual of your camera for details. Video cable (not supplied) • Select input terminal after turning on the projector. Input terminal COMPUTER IN VIDEO IN SOURCE button on the projector cabinet COMPUTER VIDEO Button on the
  • NEC NP-P502HL | Users Manual - Page 93
    use only 1 of the ports (it is not possible to connect both ports to the LAN). For controlling the projector by a HDBaseT transmitter whose control signal is not supported (or with which cannot connect the projector) or over the network, connect to the LAN port. At the same time, for controlling the
  • NEC NP-P502HL | Users Manual - Page 94
    the USB Wireless LAN Unit in the area where the use of wireless LAN equipment is prohibited, remove the USB Wireless LAN Unit from the projector. • Buy the appropriate USB Wireless LAN Unit for your country or area. NOTE: • Your computer's wireless LAN adapter (or unit) must be complied with Wi
  • NEC NP-P502HL | Users Manual - Page 95
    LAN Unit. 5. Installation and Connections 4. Mount the wireless LAN cover. (1)Insert the hook on the back of the cover into the groove in the projector and close the wireless LAN cover. Groove Hook (2)Turn the screw clockwise to tighten it. * To remove the USB Wireless LAN Unit, disconnect the
  • NEC NP-P502HL | Users Manual - Page 96
    and Connections Example of wireless LAN connection To use a LAN connection, you are required to set the Wireless LAN settings on the projector menu. Select [SETUP] → [INSTALLATION] → [NETWORK SETTINGS]. (→ page 57). The network settings can also be selected from the APPS menu. PC with wireless
  • NEC NP-P502HL | Users Manual - Page 97
    (IR commands) from an external device are only supported when the projector's power is turned on. Connection example Computer (for • The maximum transmission distance over the LAN cable is 100 m. • Please do not use other transmission equipment between the projector and transmission equipment.
  • NEC NP-P502HL | Users Manual - Page 98
    is on). The 2 (two) methods below can be used to turn on the projector's power when it is in standby mode. 1. The projector can be operated by connecting the computer and projector to the network (on the projector, using the LAN port and PC Control Utility application with [STANDBY MODE] set to
  • NEC NP-P502HL | Users Manual - Page 99
    getting warm and the possibility of fire and malfunction occurring. • For vertical installation, install the projector with the intake vent facing downwards. A stand for supporting the projector needs to be made for this purpose. In this case, the stand must be designed such that the center
  • NEC NP-P502HL | Users Manual - Page 100
    Please engage an installation service provider for the design and manufacture of the customized stand to be used for portrait projection. Please ensure that the following are complied with when designing the stand. 1. Maintain a distance of at least 100 mm between the projector intake vent and the
  • NEC NP-P502HL | Users Manual - Page 101
    site. Please search it by the model name of your projector. http://www.nec-display.com/dl/en/pj_manual/lineup.html APPS MENU screen display day and time. NETWORK INFORMATION NOTE: • APPS MENU does not support Uighur. • When this projector is not in a network, you cannot select [REMOTE DESKTOP
  • NEC NP-P502HL | Users Manual - Page 102
    web site and install it on these. (→ page 112) Miracast By wirelessly connecting the terminal units supporting the Miracast such as the Android with the projector, it enables the projector to project images transferred from these terminals. Before connecting these terminal units, set [Miracast] in
  • NEC NP-P502HL | Users Manual - Page 103
    LAN. WIRELESS LAN Set up for connecting the projector by a wireless LAN. At the same time, set up for the SIMPLE ACCESS POINT, Wi-Fi Direct, and Miracast. IMAGE EXPRESS UTILITY Set up the MODE (FREE, MANAGED) for the IMAGE EXPRESS UTILITY. NETWORK SERVICE Set up various setting for the AMX, HTTP
  • NEC NP-P502HL | Users Manual - Page 104
    be used for operating the APPS MENU. Perform the set up for using it. PROGRAM TIMER Once day and time is set up, changing the projector's condition in powering ON/standby, switching input signals, and switching ECO mode can be automatically performed. DATE AND TIME Determine time zone and summer
  • NEC NP-P502HL | Users Manual - Page 105
    not support "Meeting Mode" in Image Express Utility 2.0 supplied with our other models. Download Service and Operating Environment Please visit our website about operating environment and download service for each software: Visit URL: http://www.nec-display.com/dl/en/index.html Download - Projector
  • NEC NP-P502HL | Users Manual - Page 106
    over a LAN (Image Express Utility Lite) Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM allows you to send the computer's screen image to the projector over a wired or wireless LAN. Image Express Utility Lite is a program compatible with Windows. Image Express
  • NEC NP-P502HL | Users Manual - Page 107
    space (about 100 MB) to install the program. 1. Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed , click "I agree." and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation
  • NEC NP-P502HL | Users Manual - Page 108
    LAN by following the instructions in "Connecting to a Wired LAN" (→ page 80) and "Connecting to a Wireless LAN (Optional: NP05LM series)" (→ page 81). Step 3: Start Image Express Utility Lite. 1. On Windows, click "Start" → "All programs" → "NEC Projector UserSupportware" → "Image Express Utility
  • NEC NP-P502HL | Users Manual - Page 109
    . This will eliminate the trouble of installing Image Express Utility Lite to your computer. 1. Copy Image Express Utility Lite to removable media. Copy all the folders and files (total size approx. 7 MB) from the "IEU_Lite (removable-media)" folder in the supplied NEC Projector CD-ROM to the root
  • NEC NP-P502HL | Users Manual - Page 110
    Express Utility Lite for Mac on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM Applications folder on OS X. Step 2: Connect the projector to a LAN Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page
  • NEC NP-P502HL | Users Manual - Page 111
    from an Angle (GCT) Install Image Express Utility Lite on the computer and launch it to display the control window. (→ page 95) Preparation: Adjust the projector position or the zoom so that the projected image can cover the whole screen area. 1. Click the " button. " (Others) icon and then the
  • NEC NP-P502HL | Users Manual - Page 112
    4. Click the " "(Projection) icon and then the " button. "(Exit) 5. Click "Yes". 6. Start the Image Express Utility Lite again. 7. Click the " " (Picture) icon and then the " " button. The "4-point Correction" window will be displayed. 8. Click the "Start Correction" button and then "Start 4-
  • NEC NP-P502HL | Users Manual - Page 113
    to exit the GCT. TIP: • After performing the 4-point correction, you can save the 4-point correction data to the projector by clicking "File" → "Export to the projector..." on the "4-point Correction" window. • See the Help of Image Express Utility Lite for operating "4-point Correction" window and
  • NEC NP-P502HL | Users Manual - Page 114
    Utility Pro 4/ Pro 5) Using the utility software "PC Control Utility Pro 4" and "PC Control Utility Pro 5" included on the companion NEC Projector CD-ROM, the projector can be controlled from a computer over a LAN. PC Control Utility Pro 4 is a program compatible with Windows. (→ this page) PC
  • NEC NP-P502HL | Users Manual - Page 115
    USER LICENSE AGREEMENT" carefully. 4 If you agree, click "I accept the terms in the license agreement" and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window. TIP: • Uninstalling
  • NEC NP-P502HL | Users Manual - Page 116
    to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 80) and "Connecting to a Wireless LAN (Optional: NP05LM series)" (→ page 81). Step 3: Start PC Control Utility Pro 4 Click "Start" → "All programs" or "Programs" → "NEC Projector User Supportware" → "PC Control Utility
  • NEC NP-P502HL | Users Manual - Page 117
    PC Control Utility Pro 5 on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM instructions on the installer screens to complete the installation. Step 2: Connect the projector to a LAN Connect the projector to the LAN by following the instructions in
  • NEC NP-P502HL | Users Manual - Page 118
    Utility Pro 5 to the Trash icon. • The configuration file of PC Control Utility Pro 5 is located in "/Users//Application Data/NEC Projector User Supportware/PC Control Utility Pro 5". Viewing the Help of PC Control Utility Pro 5 • Displaying the Help file of PC Control Utility Pro
  • NEC NP-P502HL | Users Manual - Page 119
    NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed on your computer screen. This will help you perform operations such as projector is not supported by Virtual Remote Tool. • For update information on Virtual Remote Tool, visit our website: http://www.nec-display.com/dl
  • NEC NP-P502HL | Users Manual - Page 120
    the background logo by using the image file (P502HL: /Logo/NEC_logo2012_1920x1080.bmp, P502WL: /Logo/NEC_logo2011_1280x800.bmp) inclulded on the supplied NEC Projector CD-ROM. TIP: • The projector's COMPUTER IN terminal supports DDC/CI (Display Data Channel Command Interface). DDC/CI is a standard
  • NEC NP-P502HL | Users Manual - Page 121
    . Read "END USER LICENSE AGREEMENT" carefully. 4 If you agree, click "I accept the terms in the license agreement" and then click "Next". • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window. 108
  • NEC NP-P502HL | Users Manual - Page 122
    /Change" or "Uninstall". • When the "User Account Control" windows is displayed, click "Continue". Follow the instructions on the screens to complete the uninstallation. Step 2: Connect the projector to the computer 1 Use the supplied computer cable (VGA) to connect the COMPUTER IN terminal of the
  • NEC NP-P502HL | Users Manual - Page 123
    menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual Remote Tool starts for the first time, "Easy Setup" window will be displayed. Follow the instructions on the screens When "Easy Setup" is completed
  • NEC NP-P502HL | Users Manual - Page 124
    Click "Help". The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click "Start" → "All programs" or "Programs" → "NEC Projector User Supportware" → "Virtual Remote Tool" → and then "Virtual Remote Tool Help" in this order. The Help screen will be displayed. 111
  • NEC NP-P502HL | Users Manual - Page 125
    photos and documents saved on terminals as a smartphone or a tablet to the projector via the wireless LAN and project them. There are two kinds of Wireless Image For Android http://www.nec-display.com/dl/en/pj_android/wiu_for-android.html For iOS http://www.nec-display.com/dl/en/pj_ios/wiu_for-ios.html
  • NEC NP-P502HL | Users Manual - Page 126
    8. Maintenance ❶ Cleaning the Lens • Turn off the projector before cleaning. • The projector has a plastic lens. Use a commercially available plastic lens cleaner. • Do not scratch or mar the lens surface as a plastic lens is easily scratched. • Never use
  • NEC NP-P502HL | Users Manual - Page 127
    cleaned regularly. • Do not scratch or hit the cabinet with your fingers or any hard objects • Contact your dealer for cleaning the inside of the projector. NOTE: Do not apply volatile agent such as insecticide on the cabinet, the lens, or the screen. Do not leave a rubber or vinyl product in
  • NEC NP-P502HL | Users Manual - Page 128
    Appendix ❶ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages eliminated. LIGHT Indicator Indicator Condition Off Steady Green light Projector Condition No trouble or [ECO MODE] is set to [OFF]. - [ECO MODE]
  • NEC NP-P502HL | Users Manual - Page 129
    will start to blink (2-cycle On and OFF). Should this happen, do the following: • Unplug the power cord after the cooling fans stop. • Move the projector to a cooler location if the room where you are presenting is particularly too warm. • Clean the vents if they are clogged with dust. • Wait about
  • NEC NP-P502HL | Users Manual - Page 130
    any trouble and failure caused by this installation. • Signals may not be supported depending on the projector to improve its angle to the screen. (→ page 16) • Ensure that the distance between the projector and is supported by the projector. (→ page 126) • Adjust the computer image manually with
  • NEC NP-P502HL | Users Manual - Page 131
    on the projector cabinet or the remote control. (→ page 23) • Adjust the computer image manually with [CLOCK display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use display modes other than those supported by your Mac and the projector, changing the DIP switch
  • NEC NP-P502HL | Users Manual - Page 132
    ❷ Specifications This section provides technical information about projector's performance. 9. Appendix Model name NP-P502HL NP-P502WL Method 1 Chip DLP type Specifications of main parts DMD panel Size 0.65" (aspect ratio: 16:9) 0.65" (aspect ratio: 16:10) Pixels (*1) 2,073,600 (1920
  • NEC NP-P502HL | Users Manual - Page 133
    NP-P502HL NP-P502WL Operating temperature: 5 to 40°C (*5) Operating humidity: 20 to 80% (with no condensation) Storage temperature: −10 to 50°C (*5) Storage humidity: 20 to 80% (with no condensation) Operating altitude: 0 to 2600 m/8500 feet (Set [FAN MODE] to [HIGH] when using the projector
  • NEC NP-P502HL | Users Manual - Page 134
    ❸ Cabinet Dimensions Unit: mm (inch) 9. Appendix 370 (14.6) 365 (14.4) 20 (0.8) 137 (5.4) 92 (3.6) Lens center 94 (3.7) 469 (18.5) 250 (9.8) 89 (3.5) 200 (7.9) 121
  • NEC NP-P502HL | Users Manual - Page 135
    bundled cables in the cable cover. Doing so may damage the power cord, resulting in a fire. • Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover. Doing so may damage the cable cover, resulting in injury. Attaching the cable cover Tool
  • NEC NP-P502HL | Users Manual - Page 136
    cover does not drop. • The screws cannot be removed. 9. Appendix 2. Remove the cable cover. (1)Rotate a little downwards so that the claw comes out of the projector's groove. (2)Slide downwards so that the claw on the cover edge comes out of the
  • NEC NP-P502HL | Users Manual - Page 137
    9. Appendix ❺ Pin assignments and signal names of main terminals COMPUTER IN Terminal (Mini D-Sub 15 Pin) Connection and signal level of each pin 11 12 13 14 15 6 7 8 9 10 1 23 45 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
  • NEC NP-P502HL | Users Manual - Page 138
    Ethernet/HDBaseT/LAN Port (RJ-45) 12345678 Pin No. 1 2 3 4 5 6 7 8 Signal TxD+/HDBT0+ TxD−/HDBT0− RxD+/HDBT1+ Disconnection/HDBT2+ Disconnection/HDBT2− RxD−/HDBT1− Disconnection/HDBT3+ Disconnection/HDBT3− USB Port (Type A) 1 2 3 4 Pin No. 1 2 3 4 VBUS D− D+ Grounding Signal PC CONTROL Port
  • NEC NP-P502HL | Users Manual - Page 139
    , select [16:9] for [ASPECT RATIO]. *3 WXGA MODE: OFF *4 WXGA MODE: ON *5 120Hz signals are supported for Frame Sequential only. NOTE: • An image with higher or lower resolution than the projector's native resolution (1280 × 800) will be displayed with Advanced AccuBlend. • Sync on Green and
  • NEC NP-P502HL | Users Manual - Page 140
    Send" together on both ends of the cable to simplify cable connection. NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. 127
  • NEC NP-P502HL | Users Manual - Page 141
    the computer for displaying the web page correctly. 1. Access to the software download support page in our web site. URL: http://www.nec-display.com/dl/en/pj_soft/lineup.html 2. Check if the software installed on the projector in use is updated. • You can check the software version from either
  • NEC NP-P502HL | Users Manual - Page 142
    of the HTTP transmission. The error codes other than above may be displayed. If an error is found during the software update, turn on the projector and update the file again. When the software update is not completed properly even if you tried to update several times, please consult your dealer
  • NEC NP-P502HL | Users Manual - Page 143
    service personnel, check the following list to be sure repairs are needed also by referring to the "Troubleshooting" section in your user's manual. This checklist below will help us solve your problem □ Input source's resolution and frequency are supported by the projector. □ Image is too dark. □
  • NEC NP-P502HL | Users Manual - Page 144
    problem in detail. 9. Appendix Information on application and environment where your projector is used Projector Projector PC Installation environment Screen size: inch Screen type: □ White matte □ Beads □ Polarization □ Wide angle □ High contrast Throw distance Signal cable NEC standard
  • NEC NP-P502HL | Users Manual - Page 145
    on the marking plate (on the bottom of the product). To see a list of our TCO certified projectors and their TCO Certification (in English only), visit our website at http://www.nec-display.com/ap/en_projector/tco/index.html The TCO certification, designed by TCO Development, is an international
  • NEC NP-P502HL | Users Manual - Page 146
    States, Canada, and Mexico) Please take time to register your new projector. This will activate your limited parts and labor warranty and InstaCare service program. Visit our web site at www.necdisplay.com, click on support center/register product and submit your completed form online. Upon receipt
  • NEC NP-P502HL | Users Manual - Page 147
    © NEC Display Solutions, Ltd. 2015 7N952241
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Projector
P502HL/P502WL
User’s Manual
Model No.
NP-P502HL, NP-P502WL