Home » NEC Manuals » Projectors » NEC NP610 » Manual Viewer

NEC NP610 NP310 : NP600CM Mount Instructions

NEC NP610 - XGA LCD Projector Manual

UPC - 805736031157

View all NEC NP610 manuals

Add to My Manuals
Save this manual to your list of manuals

NEC NP610 manual content summary:

NEC NP610 | NP310 : NP600CM Mount Instructions - Page 1
Display Solutions of America, Inc. Installation and Assembly Manual: Custom Ceiling Mount for NEC NP400, NP500, NP500W, and NP600 Projectors Model: NP600CM Maximum Load Capacity: 50 lb (22.7 kg) Features: • ImageLockTM alignment prevents picture sag or drift • Wrench access slot for easier flush
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 2
Parts List ...3 Installation to Extension Columns / Ceiling Plate ...4 Installation to Wood Joist Ceilings ...5 Installation to Concrete Ceilings ...6 Installation to Threaded Rods ...7 Attaching Adapter Plate to Projector ...8 Attaching Adapter Plate to Projector Mount ...9 Projector Alignment
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 3
socket pin screw 1 055-2869 E G 3 510-2087 CC retaining spacer 3 590-2009 DD 2 mm allen wrench 1 560-1097 NOTE: Actual parts may appear slightly different than illustrated. F B AA BB CC DD 1 Disengage connection block from projector mount assembly (A) by unscrewing captive screw and
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 4
Installation to Extension Column / Ceiling Plate 2 NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 2.1. NOTE: For 3/4" extension columns, reducer ACC 913
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 5
of the studs. The use of an "edge to edge" stud finder is highly recommended. 2 Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Make sure that the mounting holes are in the center of the wood joist. Drill two 5/32" (4 mm) dia. holes to
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 6
until projector mount assembly (A) is firmly attached. NOTE: It is the responsibility of the installer to verify that the ceiling will safely support the to concrete ceiling covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete ceiling covered with plaster/
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 7
two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly (A) to the two 1/4-20 threaded rods using two 1/4-20 hex thin nylon-insert locknuts as shown in figure 2.7 or figure
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 8
3 Align shoulder on connection block opposite notch in adapter plate (AA). Attach adapter plate to connection block from projector mount assembly (A) using two #10-32 x 3/8" serrated washer head socket pin screws (C) as shown in figure 3.1. Tighten using 4 mm allen wrench (B). NOTCH INDICATES
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 9
handle placement of the screen. 5 Slide connection block with projector into projector mount assembly (A) as shown. Tighten captive screw to secure projector to projector mount assembly (A). ARROW INDICATES FRONT OF MOUNT FRONT OF MOUNT A CONNECTION BLOCK CAPTIVE SCREW 6 IMPORTANT: For security
NEC NP610 | NP310 : NP600CM Mount Instructions - Page 10
ceiling, and threaded rod mounting applications: Loosen wood screws (F) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), or loosen locknuts on threaded rods (page 7), until projector mount can be rotated. Rotate mount or registered trademarks of their respective owners.