Netgear GSM7324NA FSM7326P Command line reference manual
Netgear GSM7324NA Manual
 |
View all Netgear GSM7324NA manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7324NA manual content summary:
- Netgear GSM7324NA | FSM7326P Command line reference manual - Page 1
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Version 6.0 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10236-01 February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 2
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. EN 55 022 Declaration of Conformance This is to certify that the ProSafe 7300 Series Layer-3 Managed Switch in the operating instructions. The Federal Office - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 3
: Publication Date: Product Family: Product Name: Home or Business Product: Language: Publication Part Number: Publication Version Number FSM7326P, GSM7324, GSM7312 February 2007 managed switch ProSafe 7300 Series Layer-3 Managed Switch Business English 202-10236-01 1.0 iii v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 4
iv v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 5
Contents Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Version 6.0 Chapter 1 About This Manual 1.1...Audience 1-1 1.2...Scope 1-1 1.3 Typographical Conventions 1-2 1.4 Special Message Formats 1-2 1.5 How to Use This Manual 1-3 1.6 How to Print this - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 6
Transfer Protocol (HTTP) Commands 3-17 3.6.1 ip http secure-port 3-17 3.6.2 ip http secure-protocol 3-18 3.6.3 ip http secure-server 3-18 3.6.4 ip http server 3-18 3.6.5 network javamode 3-19 3.6.6 ...show ip http 3-19 3.7 User Account Commands 3-20 3.7.1 ...users name 3-20 vi v1.0, February - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 7
users snmpv3 authentication 3-22 3.7.5 users snmpv3 encryption 3-22 3.7.6 show loginsession 3-23 3.7.7 ...show users 3-23 3.7.8 ...disconnect 3-24 Chapter 4 Port and System Setup Commands 4.1 Port Configuration Commands 4-1 4.1.1 ...interface 4-1 4.1.2 interface range 4-2 4.1.3 interface vlan - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 8
4.4.8 show mac-address-table stats 4-20 4.5 DNS Client Commands 4-21 4.5.1 ip domain-lookup 4-22 4.5.2 ip domain-name 4-22 4.5.3 ip name-server 4-22 4.5.4 ...ip host 4-22 4.5.5 ...clear host 4-23 4.5.6 ...show hosts 4-23 Chapter 5 Spanning Tree Protocol Commands 5.1 STP Configuration Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 9
5-12 5.2.3 show spanning-tree interface 5-13 5.2.4 show spanning-tree mst port detailed 5-14 5.2.5 show spanning-tree mst port summary 5-16 5.2.6 show spanning-tree mst summary 5-16 5.2.7 show spanning-tree vlan 5-17 Chapter 6 VLAN Commands 6.1 VLAN Configuration Commands 6-1 6.1.1 vlan - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 10
6-14 6.3.1 vlan port priority all 6-14 6.3.2 ...vlan priority 6-14 Chapter 7 DHCP Commands 7.1 DHCP Server Commands (DHCP Config Pool Mode) 7-2 7.1.1 ...ip dhcp pool 7-2 7.1.2 client-identifier 7-2 7.1.3 ...client-name 7-3 7.1.4 default-router 7-3 7.1.5 ...dns-server 7-4 7.1.6 hardware-address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 11
clear ip dhcp binding 7-12 7.3.2 clear ip dhcp server statistics 7-12 7.3.3 clear ip dhcp conflict 7-12 7.3.4 show ip dhcp binding 7-12 7.3.5 show ip dhcp global configuration 7-13 7.3.6 show ip dhcp pool configuration 7-13 7.3.7 show ip dhcp server statistics 7-14 7.3.8 show ip dhcp conflict - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 12
gmrp configuration 8-8 8.3.4 show mac-address-table gmrp 8-9 Chapter 9 Port-Based Traffic Control Commands 9.1 Port Security Commands 9-1 9.1.1 ...port-security 9-2 9.1.2 port-security max-dynamic 9-2 9.1.3 port-security max-static 9-3 9.1.4 port-security mac-address 9-3 9.1.5 port-security - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 13
-4 11.1.8 dot1x port-control 11-4 11.1.9 dot1x port-control all 11-5 11.1.10 dot1x re-authenticate 11-5 11.1.11 dot1x re-authentication 11-6 11.1.12 dot1x system-auth-control 11-6 11.1.13 dot1x timeout 11-6 11.1.14 dot1x user 11-7 11.1.15 users defaultlogin 11-8 11.1.16 users login 11-8 11 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 14
11.2.7 radius server timeout 11-16 11.2.8 show radius 11-17 11.2.9 show radius accounting 11-18 11.2.10 show radius statistics 11-19 Chapter 12 Port-Channel/LAG (802.3ad) Commands 12.1 Port-Channel Configuration Commands 12-2 12.1.1 ...addport 12-2 12.1.2 deleteport (Interface Config) 12-2 12 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 15
-13 13.3.10 match ip dscp 13-14 13.3.11 match ip precedence 13-15 13.3.12 match ip tos 13-15 13.3.13 match protocol 13-16 13.3.14 match source-address mac 13-16 13.3.15 match srcip 13-17 13.3.16 match srcl4port 13-17 13.3.17 match vlan 13-17 13.4 DiffServ - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 16
) Commands 13-35 13.8.1 access-list 13-36 13.8.2 ip access-group 13-37 13.8.3 show ip access-lists 13-38 13.8.4 show access-lists 13-38 Chapter 14 Routing Commands 14.1 Address Resolution Protocol (ARP) Commands 14-1 14.1.1 ...arp 14-1 14.1.2 ip proxy-arp 14-2 14.1.3 arp cachesize 14-2 xvi v1 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 17
...ip route 14-8 14.2.5 ip route default 14-9 14.2.6 ip route distance 14-10 14.2.7 ip forwarding 14-10 14.2.8 ip netdirbcast 14-11 14.2.9 ...ip mtu 14-11 14.2.10 encapsulation 14-12 14.2.11 clear ip route all 14-12 14.2.12 clear ip route mpls 14-12 14.2.13 clear ip route mpls - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 18
-19 14.3.2 ip irdp address 14-19 14.3.3 ip irdp holdtime 14-20 14.3.4 ip irdp maxadvertinterval 14-20 14.3.5 ip irdp minadvertinterval 14-21 14.3.6 ip irdp preference 14-21 14.3.7 show ip irdp 14-21 14.4 Virtual LAN Routing Commands 14-22 14.4.1 vlan routing 14-22 14.4.2 show ip vlan 14-23 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 19
12 transmit-delay 14-38 14.6.21 default-information originate (OSPF) 14-38 14.6.22 default-metric (OSPF) 14-39 ip ospf 14-48 14.6.41 show ip ospf area 14-50 14.6.42 show ip ospf database 14-51 14.6.43 show ip ospf interface 14-52 14.6.44 show ip ospf interface 14-53 14.6.45 show ip - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 20
version 14-64 14.7.12 hostroutesaccept 14-64 14.7.13 split-horizon 14-65 14.7.14 redistribute 14-65 14.7.15 show ip rip 14-66 14.7.16 show ip rip interface 14-67 14.7.17 show ip rip interface 14-67 Chapter 15 IGMP Snooping Commands 15.1 IGMP Snooping Configuration Commands 15-1 15 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 21
.2.1 show ip igmp 15-6 15.2.2 show ip igmp mrouter interface 15-8 15.2.3 show ip igmp mrouter vlan 15-8 15.2.4 show mac-address-table igmpsnooping 15-8 15.3 IGMP Querier Commands 15-9 15.3.1 ip igmpsnooping querier 15-10 15.3.2 ip igmpsnooping querier ip-address 15-10 15.3.3 ip igmpsnooping - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 22
.2.7 clear port-channel 17-18 17.2.8 clear traplog 17-18 17.2.9 clear vlan 17-19 17.2.10 ...copy 17-19 17.2.11 ...logout 17-21 17.2.12 ...ping -26 17.3.12 show logging traplogs 17-27 17.4 CLI Command Logging Command 17-27 17.4.1 logging cli-command 17-27 17.5 Configuration Scripting Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 23
17-32 17.8.1 terminal length 17-32 17.8.2 terminal no length 17-33 Chapter 18 UDP Relay Commands 18.1 UDP Relay Configuration Commands 18-2 18.1.1 ip helper-address (global config mode) 18-2 18.1.2 ip helper-address (interface config mode) 18-3 18.2 UDP Relay Show Commands 18-3 18.2.1 show - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 24
xxiv v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 25
Chapter 1 About This Manual This chapter introduces the Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Version 6.0. It describes the command-line interface (CLI) commands used to view and configure the 7300 Series Managed Switch software. You can access the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 26
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Note: Product updates are available on the NETGEAR Web site at http://kbserver.netgear.com/products/. 1.3 Typographical Conventions This guide uses the following typographical conventions: Table 1-2. - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 27
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 1.5 How to Use This Manual The HTML version of this manual includes the following: • Buttons and one page at a time. for browsing forwards or backwards through the manual •A button that displays the table - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 28
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • Printing the Full Manual. Use the Complete PDF Manual link at the top left of any page. - Click the Complete PDF Manual link at the top left of any page in the manual. The PDF version of the complete manual opens in a browser - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 29
switching frames, based on Layer 2, 3, or 4 information contained in the frames. • Provide a complete device management portfolio to the network administrator. 2.1 Scope 7300 Series Managed Switch software encompasses both hardware and software support. It software -Port Naming Convention" on page - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 30
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • Section 2.2.4 such as show network or clear vlan, do not require parameters. Other commands parameter values in a specific order, and optional • Default shows the default value, if any, of a configurable setting - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 31
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.2 Command Conventions In this document, the command name is in bold font. Parameters are in italic font. You must replace the parameter name with - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 32
user-defined strings. Table 2-2 describes common parameter values and value formatting. Table 2-2. Parameter Descriptions Parameter Description ipaddr macaddr areaid routerid Interface or slot/port Logical Interface Character strings This parameter is a valid IP address. You can enter the IP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 33
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.3 Slot-Port Naming Convention 7300 Series Managed Switch software references physical entities such as cards and ports by using a Slot-Port (SP) naming convention. The software also uses this convention to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 34
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.5 Command Modes The CLI groups commands into modes according to the command function. Each of the command modes supports specific 7300 Series Managed Switch software commands. The commands in one mode - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 35
Line Config This is the first level of access. From the User EXEC mode, enter enable. From the Privileged EXEC mode, enter configure. From the Privileged EXEC mode, enter vlan database. From the Global Config mode, enter interface . From the Global Config mode, enter lineconfig. To exit - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 36
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Table extended . From the Global Config mode, enter ip dhcp pool . Exit or Access Previous Mode To exit 2.2.6 Entering CLI Commands The 7300 Series Managed Switch supports several features to help you enter commands. - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 37
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.6.2 CLI Error Messages entry. You can access this list from the CLI by entering help from the User or Privileged EXEC modes. Table 2-8. CLI Editing Conventions Key Sequence Description DEL or - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 38
of the router. Select DHCP, BootP, or None as the network config protocol. Configure the Management VLAN ID of the switch. If the help output shows a parameter in angle brackets, you must replace the parameter with a value. (switch) #network parms ? Enter the IP Address. If there are no - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 39
direct connection to the console port. You cannot access the system remotely until the system has an IP address and subnet mask. You can set the network configuration information manually, or you can configure the system to accept these settings from a BOOTP or DHCP server on your network. For more - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 40
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2-12 v1.0, February 2007 Overview - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 41
Access Commands This section describes the management access and basic port configuration commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 3.1 "Network Interface Commands" on page 3-1 • Section 3.3 "Console Port Access Commands" on page - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 42
gateway of the device. The IP Address and the gateway must be on the same subnet. Format network (parms | parameter) [] Mode Privileged EXEC 3.1.3 network mgmt_vlan This command configures the Management VLAN ID. Default 1 Format network mgmt_vlan Mode - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 43
do not affect the configuration of the front panel ports through which traffic is switched or routed. Format show network Modes Privileged EXEC User EXEC IP Address The IP address of the interface. The factory default value is 0.0.0.0 Subnet Mask The IP subnet mask for this interface - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 44
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Network Configuration Protocol Current Java Mode Web Mode Indicates which network protocol is being used. The options are bootp | dhcp | none. Specifies if the switch should allow access to the Java applet in the header frame. Enabled - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 45
the task. The tool is applicable to all NETGEAR 7000-series managed switches, and allows you to configure the following parameters: 1. The administrator's user password and administrator-enable password 2. Management CPU IP address and network mask 3. System name and location information - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 46
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The following is an example of an ezconfig session. NETGEAR EZ Configuration Utility Hello and Welcome! This utility will walk you thru assigning the IP address for the switch management CPU. It will allow you - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 47
ProSafe 7300 Series Layer-3 Switches, Software Ver- There are changes detected, do you wish to save the changes permanently (Y/N)? y The configuration changes have been saved succesfully. Please enter 'show running-config' to see the final configuration. Thanks for using EzConfig! 3.3 Console Port - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 48
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.3.3 serial baudrate This command specifies the communication rate of the terminal interface. The supported rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. Default 9600 Format serial baudrate - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 49
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.3.5 show serial This command displays serial communication settings for the switch. Format show serial Modes Privileged EXEC User EXEC Serial Port Login Timeout (minutes) Specifies the time, in - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 50
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4 Telnet Commands This section describes the commands you use to configure and view telnet settings. You can use telnet to manage the device from a remote management host. 3.4.1 telnet This command establishes - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 51
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4.3 transport output telnet This command the session is ended or an abnormal network error ends it. Default enabled Format transport output telnet Mode Line Config 3.4.3.1 no transport output - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 52
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4.5 session-timeout This command sets the telnet session timeout value.The timeout value unit of time is minutes. A value of 0 indicates that a session remains active indefinitely. Default 0 Format session-timeout - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 53
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4.7 telnetcon the telnet connection session timeout value to the default. Note: Changing the timeout value for active show telnet Modes Privileged EXEC User EXEC Outbound Telnet Login Timeout Indicates the number of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 54
the ProSafe 7300 Series Layer-3 Switches, Software Ver- User EXEC Remote Connection Login Timeout (minutes) This object indicates the number of minutes a remote connection session is allowed to remain inactive before being logged off. May be specified as a number from 1 to 160. The factory default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 55
the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.5 Secure Shell (SSH) Command This section describes the commands you use to configure SSH access to the switch. Use SSH to access the switch from a remote management host. Note: The system allows a maximum of 5 SSH sessions. 3.5.1 ip ssh - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 56
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.5.3 sshcon maxsessions This command specifies the maximum number of SSH connection sessions that can be established. A value of 0 indicates that no ssh connection can be established. The range is 0 to 5. Default 5 Format sshcon - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 57
switch. Access to the switch by using a Web browser is enabled by default. Everything you can view and configure by using the CLI is also available by using the Web. 3.6.1 ip http secure-port This command is used to set the SSL port where port can be 1-65535 and the default is port 443. Default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 58
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.6.2 ip http secure-protocol This command is used to set protocol levels (versions). The protocol level can be set to TLS1, SSL3 or to both TLS1 and SSL3. Default SSL3 and TLS1 Format ip http secure-protocol [SSL3 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 59
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.6.5 network javamode This command specifies whether or not the switch should allow access to the Java applet in the header frame of the Web interface. When access is enabled, the Java applet can be - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 60
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7 User Account Commands This section describes the commands you use to add, manage, and delete system users. The 7300 Series Managed Switch has two default users: admin and guest. The admin user can view and configure system settings - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 61
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7.2 users passwd Use this command to change a password. Passwords are a maximum of eight alphanumeric characters. If a user is authorized for authentication or encryption is enabled, the password length must be at - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 62
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7.4 users snmpv3 authentication This command specifies the authentication protocol to be used for the specified user. The valid authentication protocols are none, md5 or sha. If you specify md5 or sha, the login password is also - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 63
This command displays current telnet and serial port connections to the switch. Format show loginsession Mode Privileged EXEC ID Login Session ID User Name The name the user will use to login using the serial port or Telnet. Connection From IP address of the Telnet client machine or EIA - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 64
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- SNMPv3 Access Mode SNMPv3 Authentication SNMPv3 Encryption This field displays the SNMPv3 Access Mode. If the value is set to ReadWrite, the SNMPv3 user is able to set and retrieve parameters on the system - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 65
and system setup commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 4.1 "Port Configuration Commands" on page 4-1 • Section 4.2 "Pre-login Banner and System Prompt Commands" on page 4-9 • Section 4.3 "Simple Network Time Protocol (SNTP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 66
ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.2 interface range This command gives you access to a range of port interfaces, allowing the same port configuration to be applied to a set of ports. Format interface range - Mode Global Config 4.1.3 interface vlan - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 67
any extra bytes that Layer-2 headers might require. To configure the IP MTU size, which is the maximum size of the IP packet (IP Header + IP payload), see Section 14.2.9 "ip mtu" on page 14-11. Default Format Mode 1518 (untagged) mtu Interface Config Port and System Setup Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 68
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.7.1 no mtu This command sets the default MTU size (in bytes) for the interface. Format no mtu Mode Interface Config 4.1.8 shutdown This command disables a port. Note: You can use the shutdown - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 69
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.9 shutdown all This command disables all ports. Note: You can use the shutdown command on physical and port-channel (LAG) interfaces, but not on VLAN routing interfaces. Default Format Mode enabled shutdown - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 70
Global Config 4.1.12.1 no monitor session This command removes the monitor session (port monitoring) designation from the source probe port, the destination monitored port and all VLANs. Once the port is removed from the VLAN, the user must manually add the port to any desired VLANs. Note: This - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 71
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.13 no monitor This command removes all the source ports and a destination port and restores the default value for mirroring session mode for all the configured sessions. Note: This is a stand-alone "no" - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 72
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Admin Mode Physical Mode Physical Status Link Status Link Trap LACP Mode Probe - this port is a probe port. Selects the Port control administration state. The port must be enabled in order for it to be - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 73
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interface Media Type Physical Mode Physical Status Link Status Loop Status Partner Flow Control Valid slot and port number separated by forward slashes. "Copper" or "Fiber" for combo port. Either "Auto" or fixed - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 74
ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3 Simple Network Time Protocol (SNTP) Commands This section describes the commands you use to automatically configure resets the poll interval for SNTP broadcast client back to the default broadcast or unicast. Default disabled Format sntp - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 75
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3.3 sntp client port This command sets the SNTP client port id to a value from 1-65535. Default 123 Format sntp client port Mode Global Config 4.3.3.1 no sntp client port This command resets the SNTP client port back to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 76
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3.5.1 no sntp unicast client poll-timeout This command resets the poll timeout for SNTP unicast clients to its default value. Format no sntp unicast client poll-timeout Mode Global Config 4.3.6 sntp - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 77
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3.8 sntp server This command configures an SNTP server (a maximum of three). The optional priority can be a value of 1-3, the version a value of 1-4, and the port id a value of 1-65535. Format sntp - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 78
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Client Supported Modes SNTP Version Port Client Mode Poll Interval Poll Timeout Poll Retry Supported SNTP Modes (Broadcast, Unicast, or Multicast). The highest SNTP version the client supports SNTP Client Port Configured SNTP Client - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 79
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Port Last Attempt Time Last Attempt Status Total Unicast Requests Failed Unicast Requests Server Port Number Last server attempt time for the specified server. Last server attempt status for the server. Number of requests - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 80
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.1 network mac-address This command sets locally administered MAC addresses. The following rules apply: • Bit 6 of byte 0 (called the U/L bit) indicates whether the address is universally administered (b'0') or - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 81
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.3 bridge aging-time This command configures the forwarding database address aging timeout in seconds. In an IVL system, the [fdbid | all] parameter is required. Default 300 Format bridge aging-time - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 82
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.4 show forwardingdb agetime This command displays the timeout for address aging. In an IVL system, the [fdbid | all] parameter is required. Default all Format show forwardingdb agetime [fdbid | all - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 83
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interfaces Forwarding Interfaces The list of interfaces that are designated for forwarding (Fwd:) and filtering (Flt:). The resultant forwarding list is derived from combining - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 84
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.7 show mac-address-table staticfiltering This command displays the Static Filtering entries in the Multicast Forwarding Database (MFDB) table. Format show mac-address-table staticfiltering Mode Privileged - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 85
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.5 DNS Client Commands The Domain Name System (DNS) is an Internet directory service. DNS is used to translate domain names to IP addresses. A DNS Client (often referred to as a resolver) uses a defined - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 86
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.5.1 ip domain-lookup To enable the IP Domain Naming System (DNS)-based host name-to-address translation, use the ip domain-lookup global configuration command. To disable the DNS, use the no form of this - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 87
ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode [no] ip host name address Global Config 4.5.5 clear host To delete entries from the host name-to-address display the default domain name, a list of name server hosts, the static and the cached list of host names and addresses, use - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 88
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4-24 Port and System Setup Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 89
the 7300 Series Managed Switch CLI. STP switch. For every configuration command, there is a show command that displays the configuration setting. 5.1 STP Configuration Commands This section describes the commands you use to configure Spanning Tree Protocol (STP). Note: STP is enabled by default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 90
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.1.1 no spanning-tree This command sets the spanning-tree operational mode to disabled. While disabled, the spanning-tree configuration is retained and can be changed, but is not activated. Format no - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 91
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.4 spanning-tree configuration revision This command sets the Configuration Identifier Revision Level for use in identifying the configuration that this switch is currently using. The Configuration Identifier Revision Level - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 92
ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.6.1 no spanning-tree edgeport all This command disables Edge Port mode for all ports (IEEE 802.1w functionality supported) • 802.1s - MST BPDUs are transmitted (IEEE 802.1s functionality supported) Default 802.1s Format spanning-tree - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 93
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.8.1 no spanning-tree forward-time This command sets the Bridge Forward Delay parameter for the common and internal spanning tree to the default value of 15. Format no spanning-tree forward-time Mode - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 94
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.11 spanning-tree max-hops This command sets the MSTP Max Hops parameter to a new value for the common and internal spanning tree. The max-hops value is a range from 1 to 127. Default 20 Format spanning-tree - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 95
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode {external-cost | auto}| port-priority } Interface Config 5.1.12.1 no spanning-tree mst This command sets the Path Cost or Port Priority for this port within the multiple spanning tree - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 96
ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Global Config 5.1.14 spanning-tree mst priority This command sets the bridge priority for a specific to the default value, i.e. 32768. Format spanning-tree mst priority Mode Global Config 5.1.15 spanning-tree mst vlan This - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 97
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.15.1 no spanning-tree mst vlan This command removes an association between a multiple spanning tree instance and a VLAN so that the VLAN is again be associated with the common and internal spanning - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 98
ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.18 spanning-tree bpduforwarding Normally a switch will not forward Spanning Tree Protocol (STP) BPDU packets if STP is disabled. However, if in some network setup, the user to view information about STP configuration and status. 5.2.1 show - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 99
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Time Since Topology Change Topology Change Count Topology Change Designated Root Root Path Cost Root Port Identifier Root Port Max Age Root Port Bridge Forward Delay Hello Time Bridge Hold Time Bridge Max - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 100
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- When you include the brief keyword, this command displays spanning tree settings for the bridge and the following information appears. Bridge Priority Configured value. Bridge Identifier The bridge - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 101
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Configuration Digest Key MST Instances Identifier used to identify the configuration currently being used. List of all multiple spanning tree instances configured on the switch 5.2.3 show spanning-tree interface - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 102
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.2.4 show spanning-tree mst port detailed This command displays the detailed settings and parameters for a specific switch port within a particular multiple spanning tree instance. The parameter - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 103
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Designated Bridge Designated Port Identifier Bridge Identifier of the bridge with the Designated Port. Port on the Designated Bridge that offers the lowest cost to the LAN. If you specify 0 (defined as the default CIST ID) as - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 104
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- CST Regional Root CST Port Cost The regional root identifier in use for this port. The configured path cost for this port. 5.2.5 show spanning-tree mst port summary This command displays the settings of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 105
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Associated FIDs Associated VLANs List of forwarding database identifiers associated with this instance. List of VLAN IDs associated with this instance. 5.2.7 show spanning-tree vlan This command displays the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 106
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5-18 Spanning Tree Protocol Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 107
available in the 7300 Series Managed Switch CLI. VLANs allow users located on different physical networks to be on the same logical network. The VLAN Commands section includes the following topics: • Section 6.1 "VLAN Configuration Commands" on page 6-1 • Section 6.2 "VLAN Show Commands" on page - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 108
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.2 network mgmt_vlan This command configures the Management VLAN ID. Default 1 Format network mgmt_vlan Mode Privileged EXEC 6.1.2.1 no network mgmt_vlan This command sets the Management VLAN ID to the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 109
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.4.1 no vlan acceptframe This command sets the frame acceptance mode per interface to Admit All. For Admit All mode, untagged frames or priority frames received on this interface are accepted and - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 110
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.7 vlan name This command changes the name of a VLAN. The name is an alphanumeric string of up to 32 characters, and the ID is a valid VLAN identification number. ID range is 1-4094. Default VLAN ID 1 - default; other VLANS - blank - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 111
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.9 vlan participation all This command configures the degree of participation for all interfaces in a VLAN. The ID is a valid VLAN identification number. Format vlan participation all {exclude | include - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 112
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.10.1 no vlan port acceptframe all This command sets the frame acceptance mode for all interfaces to Admit All. For Admit All mode, untagged frames or priority frames received on this interface are - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 113
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.13 vlan port ingressfilter all This command enables ingress filtering for all ports. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 114
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.16.1 no vlan protocol group add protocol This command removes the from this protocol-based VLAN group that is identified by this . The possible values for protocol are ip, arp, and ipx. Format - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 115
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.19 protocol vlan group This command adds the physical interface to the protocol-based VLAN identified by . You can associate multiple interfaces with a group, but you can only associate each - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 116
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.21 vlan pvid This command changes the VLAN ID per interface. When an untagged packet comes to the switch, it will be tagged with the PVID value as the VLAN ID for further processing. By default, every port belongs to VLAN 1 and the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 117
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.2 VLAN Show Commands This section describes the commands you use to view VLAN settings. 6.2.1 show vlan This command displays a list of all configured VLANs. Format show vlan Modes Privileged EXEC User EXEC VLAN ID There - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 118
7300 Series Layer-3 Switches, Software Ver- Interface Current Configured Tagging Valid slot and port number separated by forward slashes. It is possible to set the parameters for all ports by using the selectors on the top line. Determines the degree of participation of this port in this VLAN. The - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 119
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.2.3 show vlan port This command displays VLAN port information. Format show vlan port { | all} Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 120
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.3 Provisioning (IEEE 802.1p) Commands This section describes the commands you use to configure provisioning, which allows you to prioritize ports. 6.3.1 vlan port priority all This command configures the port priority assigned - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 121
available in the 7300 Series Managed Switch CLI. DHCP automatically allocates and manages client TCP/ IP configurations. DHCP uses UDP as its transport protocol and supports a number of features that facilitate in administration address allocations. The DHCP Server Commands section includes the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 122
ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1 DHCP Server Commands (DHCP Config Pool Mode) This section describes the commands you to configure the DHCP server settings for the switch. 7.1.1 ip dhcp pool This command configures a DHCP address pool name on a DHCP server and enters DHCP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 123
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.2.1 no client-identifier This command deletes the client identifier. Format no client-identifier Mode DHCP Pool Config 7.1.3 client-name This command specifies the name for a DHCP client. Name is a string - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 124
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.5 dns-server This command specifies the IP servers available to a DHCP client. Address parameters are valid IP addresses; each made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid. Default none Format - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 125
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode host [mask | prefix-length] DHCP Pool Config 7.1.7.1 no host This command removes the IP address of the DHCP client. Format no host Mode DHCP Pool Config 7.1.8 lease This command configures the duration - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 126
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.9 network Use this command to configure the subnet number and mask for a DHCP address pool on the server. Network-number is a valid IP address, made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 127
Switches, Software Ver- 7.1.11.1 no domain-name This command removes the domain name. Format no domain-name Mode DHCP Pool Config 7.1.12 netbios-name-server This command configures NetBIOS Windows Internet Naming Service (WINS) name servers that are available to DHCP clients. One IP address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 128
ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.13.1 no netbios-node-type This command removes the NetBIOS node Type. Format no netbios-node-type Mode DHCP Pool Config 7.1.14 next-server This command configures the next server in the boot process of a DHCP client. Address is the IP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 129
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.15.1 no option This command removes the options. Format no option Mode DHCP Pool Config 7.2 DHCP Server Commands (Global Config Mode) This section describes the commands you to configure the DHCP server settings for - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 130
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.2.2 ip dhcp ping packets This command is used to specify the number, in a range from 2-10, of packets a DHCP server sends to a pool address as part of a ping operation. By default the number of packets sent - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 131
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.2.4 ip dhcp bootp automatic This command enables the allocation of the addresses to the bootp client. The addresses are from the automatic address pool. Default disabled Format ip dhcp bootp automatic Mode Global - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 132
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.3 DHCP Server Clear and Show Commands This section describes the commands you to delete various DHCP information and the commands you use to view DHCP configuration information and statistics. 7.3.1 clear ip dhcp binding This - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 133
dhcp global configuration This command displays address bindings for the specific IP address on the DHCP server. If no IP address is specified, the bindings corresponding to all the addresses are displayed. Format show ip dhcp global configuration Modes Privileged EXEC User EXEC Service DHCP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 134
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The following additional field is displayed for Dynamic pool type: Network The network number and the mask for the DHCP address pool. The following additional fields are displayed for Manual pool type: Client Name - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 135
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- DHCP RELEASE DHCP INFORM Message Sent: DHCP OFFER DHCP ACK DHCP NACK The number of DHCPRELEASE messages the server has received. The number of DHCPINFORM messages the server has received. The number of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 136
the DHCP server will contain two optional fields: Circuit ID and Remote ID. The circuit ID option contains the port information where the DHCP client request originated. The remote ID option contains the MAC address of the relay agent (the switch management CPU's own MAC address). Default disabled - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 137
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.4.3 bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The parameter has a range of 1 to 16. Default 4 Format bootpdhcprelay maxhopcount - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 138
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.4.5 bootpdhcprelay serverip This command configures the server IP Address for BootP/DHCP Relay on the system. The parameter is an IP address in a 4-digit dotted decimal format. Default 0.0.0.0 Format bootpdhcprelay - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 139
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Discarded Is the number of packets discarded. 7.4.7 bootpdhcprelay backup-serverip To configure the IP address of the backup DHCP server , use the bootpdhcprelay backup-serverip command. - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 140
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7-20 v1.0, February 2007 DHCP Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 141
Protocol (GVRP), and Garp Multicast Registration Protocol (GVMP) commands available in the 7300 Series Managed Switch CLI. GARP is a protocol that allows client stations to register with the switch for membership in VLANS (by using GVMP) or multicast groups (by using GMRP). This section contains the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 142
the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.1 GARP Commands This section describes the commands you use to configure GARP and view GARP status. The commands in this section affect both GVMP and GMRP. 8.1.1 set garp timer join This command sets the GVRP join time for one or all ports - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 143
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.1.2 set garp timer leave This command sets the GVRP leave time. Leave time is the time to wait after receiving an unregister request for a VLAN or a multicast group before deleting the VLAN entry. This can be - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 144
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.1.3 set garp port and per GARP participation. The time may range from 200 to 6000 (centiseconds). The value 1000 centiseconds is 10 seconds. Note: This command has an effect only when GVRP is enabled. Default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 145
GVRP-enabled switches exchange VLAN configuration information, which allows GVRP to provide dynamic VLAN creation on trunk ports and automatic VLAN pruning. Note: If GVRP is disabled, the system does not forward GVRP messages. 8.2.1 set gvrp adminmode This command enables GVRP. Default disabled - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 146
attributes are a VLAN or multicast group. There is an instance of this timer on a per-Port, per-GARP participant basis. Permissible values are 10 to 100 centiseconds (0.1 to 1.0 seconds). The factory default is 20 centiseconds (0.2 seconds). The finest granularity of specification is one centisecond - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 147
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- LeaveAll Timer Port GMRP Mode GARP participant basis. Permissible values are 20 to 600 centiseconds (0.2 to 6.0 seconds). The factory default is 60 centiseconds (0.6 seconds). This Leave All Time controls - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 148
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.3.1.1 routing is disabled and port-channel (LAG) membership is removed from an interface that has GARP enabled. Default gmrp configuration { | all} Modes Privileged EXEC User EXEC Interface This displays the slot/port of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 149
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Join Timer Leave Timer LeaveAll Timer Port GMRP Mode Specifies the interval between the transmission of GARP PDUs registering (or re-registering) membership for an attribute. Current attributes are a VLAN or multicast group - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 150
Series Layer-3 Switches, Software Ver- Type Description Interfaces hexadecimal numbers that are separated by colons, for example 01:23:45:67:89:AB. In an IVL system the MAC address is displayed as 8 bytes. Displays the type of the entry. Static entries are those that are configured by the end user - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 151
describes the command you use to configure Port Security on the switch. Port security, which is also known as port MAC locking, allows you to secure the network by locking allowable MAC addresses on a given port. Packets with a matching source MAC address are forwarded normally, and all other - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 152
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.1 port-security This command enables port locking at the system level (Global Config) or port level (Interface Config) Default disabled Format port-security Modes Global Config Interface Config - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 153
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.3 port-security max-static This command sets the maximum number of statically locked MAC addresses allowed on a specific port. Default 20 Format port-security max-static Mode Interface - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 154
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.6 show port-security This command displays the port-security settings for the entire system. Format show port-security Mode Privileged EXEC Admin Mode Port Locking mode for the entire system - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 155
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.10 show port-security violation This command displays the source MAC address of the last packet that was discarded on a locked port. Format show port-security violation Mode Privileged - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 156
ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.1.1 no storm-control broadcast This command disables broadcast storm recovery mode. The threshold implementation follows a percentage pattern. If the broadcast traffic on any Ethernet port as for broadcast. Default disable Format storm- - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 157
ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.3.1 no storm-control unicast all This command disables multicast storm recovery mode. Format no storm-control unicast all Mode Global Config 9.2.4 storm-control broadcast This command enables broadcast storm recovery mode in per-port - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 158
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.5.1 no storm port when the port becomes oversubscribed and dropping all traffic for small bursts of time during the congestion condition. This can lead to high-priority and/or network control traffic loss. Default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 159
displays switch configuration information. Format show storm-control Mode Privileged EXEC Broadcast Storm Recovery Mode May be enabled or disabled. The factory default is disabled. 802.3x Flow Control Mode May be enabled or disabled. The factory default is disabled. Port-Based Traffic - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 160
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9-10 Port-Based Traffic Control Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 161
the commands you use to configure SNMP on switch. 10.1.1 snmp-server This command sets the name and the physical location of the switch, and the organization responsible for the network. The range for , and is from 1 to 31 alphanumeric characters. Default none Format snmp - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 162
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.2 snmp-server community This command adds (and names) a new SNMP community. A community is a name associated with the switch and with a set of SNMP managers that manage it with a specified privileged - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 163
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.3.1 no snmp-server community ipaddr This command sets a client IP address for an SNMP community to 0.0.0.0. The name is the applicable community name. Format no snmp-server community ipaddr Mode - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 164
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.5.1 no snmp-server community mode This command deactivates an SNMP community. If the community is disabled, no SNMP requests using this community are accepted. In this case the SNMP manager associated with this - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 165
ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.8.1 no snmp-server traps violation This command disables the sending of new violation traps. Format no snmp-server traps violation Mode Interface Config 10.1.9 snmp-server traps This command enables the Authentication Flag. Default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 166
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.11 snmp-server traps linkmode This command enables Link Up/Down traps for the entire switch. When enabled, link traps are sent only if the Link Trap flag setting associated with the port is enabled. Section 10 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 167
ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.13.1 no snmp-server traps stpmode This command disables the sending of new root traps and topology change notification traps. Format no snmp-server Section 10.1.2 "snmp-server community" on page 10-2. Default snmpv2 Format snmptrap < - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 168
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.15 snmptrap snmpversion support a "no" form. Default Format Mode snmpv2 snmptrap snmpversion Global Config 10.1.16 snmptrap ipaddr This command assigns an IP address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 169
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.18 snmp trap link-status This command enables link status traps by interface. Note: This command is valid only when the Link Up/Down Flag is enabled. See 'snmp-server enable traps linkmode' command. Format - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 170
not have to be reset for changes to take effect. The SNMP agent of the switch complies with SNMP Versions 1, 2 or 3. For more information about the SNMP specification, see the SNMP RFCs. The SNMP agent sends traps through TCP/IP to an external SNMP manager based on the SNMP configuration (the trap - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 171
the ProSafe 7300 Series Layer-3 Switches, Software Ver- Client IP Mask Access Mode Status Subnet Mask is set to 0.0.0.0, an IP Address of 0.0.0.0 matches all IP addresses. The default value is 0.0.0.0 A mask to be ANDed with the requesting entity's IP address before comparison with IP Address. If - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 172
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Authentication Flag Link Up/Down Flag Multiple Users Flag Spanning Tree Flag Broadcast Storm Flag DVMRP Traps OSPF Traps PIM Traps Can be enabled or disabled. The factory default is enabled. Indicates whether - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 173
Series Managed Switch CLI. The Port-Based Access and Authentication Commands section includes the following topics: • Section 11.1 "Port-Based authentication login lists can be configured on the switch. When a list is created, the authentication method "local" is set as the first method. Port- - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 174
the user's login (authentication login list) is attempted. The 7300 Series Managed Switch software does not utilize multiple entries in the user's login. If the first entry returns a timeout, the user authentication attempt fails. Note: The default login list included with the default configuration - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 175
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.2 clear dot1x statistics This command resets the 802.1x statistics for the specified port or for all ports. Format clear dot1x statistics { | all} Mode Privileged EXEC 11.1.3 clear - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 176
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.7 dot1x max-req This command sets the maximum number of times the authenticator state machine on this port will transmit an EAPOL EAP Request/Identity frame before timing out the supplicant. The < - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 177
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.8.1 no dot1x port-control This command sets the authentication mode to be used on the specified port to 'auto'. Format no dot1x port-control Mode Interface Config 11.1.9 dot1x port-control all This command - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 178
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.11 dot1x re-authentication This command enables re-authentication of the supplicant for the specified port. Default disabled Format dot1x re-authentication Mode Interface Config 11.1.11.1 no - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 179
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- quiet-period: Sets the value, in seconds, of the timer used by the authenticator state machine on this port to define periods of time in which it will not attempt to acquire a supplicant. The quiet-period - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 180
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.14.1 no dot1x user This command removes the user from the list of users with access to the specified port or all ports. Format no dot1x user { | all} Mode Global Config 11.1.15 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 181
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Method 1 Method 2 Method 3 This displays the first method in the specified authentication login list, if any. This displays the second method in the specified authentication login list, if any. This displays - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 182
ProSafe 7300 Series Layer-3 Switches, Software Ver- Control Mode Operating Control Mode Reauthentication Enabled Key Transmission Enabled The configured control mode for this port machine on the specified port to determine when to send an EAPOL EAP Request/Identity frame to the supplicant. The value, - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 183
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Supplicant Timeout Server Timeout Maximum Requests Reauthentication Period Reauthentication Enabled Key Transmission Enabled Control Direction The timer used by the authenticator state machine on this port to timeout the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 184
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- EAPOL Logoff Frames Received Last EAPOL Frame Version Last EAPOL Frame Source EAP Response/Id Frames Received EAP Response Frames Received EAP Request/Id Frames Transmitted EAP Request Frames Transmitted Invalid EAPOL Frames Received EAP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 185
. 802.1x Port Security Displays the authentication login list assigned to the user for 802.1x port security. 11.2 RADIUS Commands This section describes the commands you use to configure the 7300 Series Managed Switch to use a Remote Authentication Dial-In User Service (RADIUS) server on your - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 186
to the configured RADIUS server. The number range is 1 - 65535, with 1812 being the default value. Note: To re-configure a RADIUS authentication server to use the default UDP , set the parameter to 1812. If you use the parameter, the command configures the IP address to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 187
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.2.1 no radius server host This command is used to remove the configured RADIUS authentication server or the RADIUS accounting server. If the 'auth' token is used, the previously configured RADIUS authentication server is removed - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 188
ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.5 radius server primary This command is used to configure the primary RADIUS authentication server for this RADIUS client. The primary server is the one that is used by default for handling RADIUS requests. The remaining configured servers - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 189
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.7.1 no radius server timeout This command sets the timeout value to the default value. Format no radius server timeout Mode Global Config 11.2.8 show radius This command is used to display the various RADIUS configuration items - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 190
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.9 show radius accounting This command is used to display the configured RADIUS accounting mode, accounting server and the statistics for the configured accounting server. Format show radius accounting - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 191
RADIUS packets received from this server on the accounting port and dropped for some other reason. 11.2.10 show radius statistics This command is used to display the statistics for RADIUS or configured server. To show the configured RADIUS server statistic, the IP Address specified must match that - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 192
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Access Accepts server. The number of RADIUS packets of unknown types, which were received from this server on the authentication port. The number of RADIUS packets received from this server on the authentication port - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 193
Configuration commands configure features and options of the switch. For every configuration command, there is a show command that displays the configuration setting. • Clear commands clear some or all of the settings to factory defaults. Port-Channel/LAG (802.3ad) Commands v1.0, February 2007 12 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 194
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1 Port-Channel Configuration Commands This section describes the commands you use to configure port-channels. Assign the LAG VLAN membership after you create a LAG. If you do not assign VLAN membership, the LAG might - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 195
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1.4 port-channel This command configures a new port-channel and generates a logical slot/port number for the port-channel. The field is a character string which allows the dash "-" character as - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 196
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1.6.1 no port-channel staticcapability This command disables the support of static port-channels on the device. Format no port-channel staticcapability Mode Global Config 12.1.7 port lacpmode This command enables - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 197
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1.9.1 no port-channel adminmode This command disables a port-channel (LAG). The option all sets every configured portchannel with the same administrative mode setting. Format no port-channel adminmode [all] Mode - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 198
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.2 Port-Channel Show Commands This section describes the commands you use to view port-channel status and configuration information. 12.2.1 show port-channel This command displays the static capability - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 199
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Link Trap Mode STP Mode Mbr Ports Port Speed Type Active Ports This object determines whether or not to send a trap when link status changes. The factory default is enabled. The Spanning Tree Protocol - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 200
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12-8 Port-Channel/LAG (802.3ad) Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 201
used to display device settings, statistics and other information. 13.1 Class of Service (CoS) Commands This section describes the commands you use to configure and view Class of Service (CoS) settings for the switch. The commands in this section allow you to control the priority and transmission - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 202
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.1 ip-precedence-mapping This command maps an IP precedence value to a default internal traffic class value Format no classofservice ip-precedence-mapping Modes Global Config Interface Config 13-2 Quality of Service - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 203
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.3 classofservice ip-dscp-mapping This command maps an IP DSCP value to an internal traffic class. The value is specified as either an integer from 0 to 63, or symbolically through one of the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 204
ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.5 cos-queue min-bandwidth This command specifies the minimum transmission bandwidth guarantee for each interface queue. The total number of queues supported per interface is platform specific command restores the default weighted scheduler - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 205
classes for a specific interface. The slot/port parameter is optional and is only valid on platforms that support independent per-port class of service mappings. If specified, the IP Precedence mapping table of the interface is displayed. If omitted, the most recent global configuration settings are - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 206
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode show classofservice ip-precedence-mapping [slot/ port] Privileged EXEC The following information is repeated for each user priority. IP Precedence The IP Precedence value. Traffic Class The - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 207
the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.11 show classofservice trust This command displays the current trust mode setting for a specific interface. The slot/port parameter is optional and is only valid on platforms that support independent per-port class of service mappings - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 208
ProSafe 7300 Series Layer-3 Switches, Software Ver- If you specify the interface, the following information also appears: Interface This displays the slot/port of the interface. If displaying the global configuration for a policy/class combination 3. Service • Adding and removing a policy - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 209
marking is allowed for both IP and non-IP packets, since it updates the 802.1p user priority field contained in the VLAN tag of the layer 2 packet header. 13.2.1 diffserv This command sets the DiffServ operational mode to active. While disabled, the DiffServ configuration is retained and can be - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 210
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3 DiffServ 31 characters uniquely identifying an existing DiffServ class. Note: The class-map-name 'default' is reserved and must not be used. The class type of match-all Service (QoS) Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 211
ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.1.1 no class-map This command eliminates an existing DiffServ class. The is the name of an existing DiffServ class ( The class name 'default Mode Class-Map Config Quality of Service (QoS) Commands v1.0, February 2007 13-11 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 212
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.5 match class-map This command adds to the specified class definition . Format no match class-map Mode Class-Map Config 13-12 Quality of Service (QoS) Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 213
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.6 match cos This command adds to the specified class definition a match condition for the Class of Service value (the only tag in a single tagged packet or the first or outer 802.1Q tag of a double VLAN tagged packet). The - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 214
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- To specify the match condition as a single keyword, the value for is one of the supported port name keywords. The currently supported values are: domain, echo, ftp, ftpdata, http, smtp, - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 215
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.11 match ip precedence This command adds to the specified class definition a match condition based on the value of the IP Precedence field in a packet, which is defined as the high-order three bits of the Service Type octet - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 216
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.13 match protocol This command adds to the specified class definition a match condition based on the value of the IP Protocol field in a packet using a single keyword notation or a numeric value - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 217
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.15 match srcip This command adds to the specified class definition a match condition based on the source IP address of a packet. The parameter specifies an IP address. The parameter specifies an IP address bit mask - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 218
ProSafe 7300 Series Layer-3 Switches, Software Ver- Use the policy commands to associate a traffic class that you define by using the class command set with one or more QoS policy attributes. Assign the class/policy association to an interface to form a service of policy is specific to the inbound - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 219
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.4.1.1 no policy-map This command eliminates an existing DiffServ policy. after specifying a police command for the policy-class instance. Quality of Service (QoS) Commands v1.0, February 2007 13-19 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 220
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode conform-color - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 221
ProSafe 7300 Series Layer-3 Switches, Software Ver- Default Format Mode Incompatibilities 1 mark-cos Policy-Class-Map Config Drop, Mark IP DSCP, IP Precedence, Police 13.4.7 mark ip defaults to transmit and the violate action defaults to drop. Quality of Service (QoS) Commands v1.0, - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 222
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- For set- cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef. For set-prec-transmit, an IP Precedence value is required. It is an integer from 0-7. For set-cos-transmit an 802.1p Quality of Service (QoS) Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 223
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.5 DiffServ Service Commands Use the DiffServ service commands to assign a DiffServ traffic conditioning policy, which you specified by using the policy commands, to an interface in the incoming direction - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 224
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.5.1.1 no service-policy This command configuration information for the specified class. The is the name of an existing DiffServ class. Format show class-map Modes Privileged EXEC User - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 225
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Values the user. The fields are evaluated in accordance with the class type. The possible Match Criteria fields are: Destination IP Address, Destination Layer 4 Port, Every, IP DSCP, IP Precedence, IP TOS, Protocol Keyword - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 226
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Policy Instance Table Size Policy Instance Table Max Policy Attribute Table Size Policy Attribute Table Max Service Table Size Service Table Max Current number of entries (rows) in the Policy Instance - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 227
ProSafe 7300 Series Layer-3 Switches, Software Ver- Committed Burst Size (KB) Committed Rate (Kbps) Conform Action Conform COS Conform DSCP Value Conform IP Precedence Value Drop Mark CoS Mark IP DSCP Mark IP on the same interface. Denotes the class of service value that is set in the 802.1p header - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 228
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Non-Conform COS Non-Conform DSCP Value Non-Conform IP Precedence Value Policing Style Redirect This field displays the CoS mark value if the non-conform action is set-cos-transmit. This field displays the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 229
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Operational Status Policy Name Policy Details The current operational status of this DiffServ service interface. The name of the policy attached to the interface in the indicated direction. Attached policy - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 230
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Interface Direction Operational Status Policy Name Privileged EXEC Valid slot and port number separated by forward slashes. The traffic direction of this interface service. The current operational status of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 231
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.6.7 show service-policy This command displays a summary of policy-oriented statistics information for all interfaces in the specified direction. Format show service-policy in Mode Privileged EXEC - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 232
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- If a MAC ACL by this name list. Each rule is appended to the list of configured rules for the list. Note: The 'no' form of this command is not supported since the rules within a MAC ACL cannot be deleted - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 233
ProSafe 7300 Series Layer-3 Switches, Software VLAN tag, this is the first (or outer) tag. The assign-queue parameter allows specification of a particular hardware queue for handling traffic that matches this rule. The allowed value is 0-(n-1), where n is the number of user configurable - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 234
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode {deny|permit} { | any} { | any} [ | ] [vlan {eq }] [cos ] [assign-queue ] Mac-Access-List Config 13.7.4 mac access-group This command attaches a specific MAC - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 235
you use to configure IP ACL settings. IP ACLs ensure that only authorized users have access to specific resources and block any unwarranted attempts to reach network resources. The following rules apply to IP ACLs: • The 7300 Series Managed Switch does not support IP ACL configuration for IP packet - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 236
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • Wildcard masking for ACLs operates differently from a subnet mask. A wildcard mask is in essence the inverse of a subnet mask. With a subnet mask, the mask has ones (1's) in the bit positions that are used for the network address, and - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 237
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- IP Extended ACL: Format Mode access-list {deny | permit} {every | {{icmp | igmp | ip | tcp | udp | } [{eq { | } [{eq {| < - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 238
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.8.3 show ip access-lists This command displays an IP ACL is the number used to identify the IP ACL. Format show ip access-lists Mode Privileged EXEC Rule - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 239
ProSafe 7300 Series Layer-3 Switches, Software Ver- ACL ID Sequence Number Access List name for a MAC access list or the numeric identifier for an IP that sequence number. If the sequence number is not specified by the user, a sequence number that is one greater than the highest sequence number - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 240
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13-40 Quality of Service (QoS) Commands v1.0, February 2007 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 241
This section describes the routing commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 14.1 "Address Resolution Protocol (ARP) Commands" on page 14-1 • Section 14.2 "IP Routing Commands" on page 14-7 • Section 14.3 "Router Discovery - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 242
Series Layer-3 Switches, Software Ver- The format is 6 two-digit hexadecimal numbers that are separated by colons, for example 00:06:29:32:81:40. Format arp Mode Global Config 14.1.1.1 no arp This command deletes an ARP entry. The value for is the IP address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 243
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.1.3.1 no arp cachesize This command configures the default ARP cache size. Format no arp cachesize Mode Global Config 14.1.4 arp dynamicrenew This command enables the ARP component to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 244
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Global Config 14.1.7 arp retries This command configures the ARP count of maximum request for retries. The value for is an integer, which represents the maximum number of request for - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 245
ProSafe 7300 Series Layer-3 Switches, Software configured into IP Address Is the IP address of a device on a subnet attached to an existing routing interface. MAC Address Is the hardware MAC address of that device. Interface Is the routing slot/port associated with the device ARP entry. Routing - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 246
the ProSafe 7300 Series Layer-3 Switches, Software Ver- Type Age Is the type that was configured into Address Resolution Protocol (ARP) table information. Format show arp brief Mode Privileged EXEC Age Time (seconds) Is the time it takes for an ARP entry to age out. This value was configured - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 247
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2 IP Routing Commands This section describes the commands you use to enable and configure IP routing on the switch. 14.2.1 routing This command enables routing for an interface. You can view the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 248
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.3 ip address This command configures an IP address on an interface. You can also use this command to configure one or more secondary IP addresses on the interface. The value for is the IP Address of the interface - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 249
preference value of the static route is reset to its default. Format no ip route [{ | }] Mode Global Config 14.2.5 ip route default This command configures the default route. The value for is a valid IP address of the next hop router - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 250
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.6 ip route distance This command sets the default distance for static routes. Lower route preference values are preferred when determining the best route. The ip route and ip route default commands allow you to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 251
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.8 ip netdirbcast This command enables the forwarding of network-directed broadcasts. When enabled, network directed broadcasts are forwarded. When disabled they are dropped. Default disabled Format ip netdirbcast Mode - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 252
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The minimum IP MTU is 68 bytes.The maximum IP MTU is 1500 bytes. Default 1500 bytes Format ip mtu Mode Interface Config 14.2.9.1 no ip mtu This command resets the ip mtu to the default value. Format no ip mtu - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 253
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.13 clear ip route mpls This command removes only the MPLS route entries associated with from the route table. Format clear ip route mpls Mode Privileged EXEC 14.2.14 clear ip route ospf - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 254
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.16 clear ip route rip This command removes all the route entries learned over the network from OSPF protocol. Format clear ip route rip Mode Privileged EXEC 14.2.17 clear ip route rip This command removes - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 255
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.19 show ip interface This command displays all pertinent information about the IP interface. Format show ip interface Modes Privileged EXEC User EXEC Primary IP Address Displays the primary IP address and subnet - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 256
a frame, in bytes. 14.2.20 show ip interface This command displays summary information about IP configuration settings for all ports in the router. Format show ip interface Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. IP Address The IP - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 257
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- For each Next Hop Next Hop Intf Next Hop IP Address The outgoing router interface to use when forwarding traffic to the next destination. The outgoing router IP address to use when forwarding traffic to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 258
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Network Address Is a valid network address identifying the network on the specified interface. Subnet Mask Protocol Is a mask of the network and host portion of the IP address for the attached network. Tells - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 259
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.25 show ip stats This command displays IP statistical information. Refer to RFC 1213 for more information about the fields that are displayed. Format show ip stats Modes Privileged EXEC User EXEC 14.3 Router - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 260
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.3.2.1 no ip irdp address This command configures the default address to be used to advertise the router for the interface. Format no ip irdp address Mode Interface Config 14.3.3 ip irdp holdtime This command - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 261
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.3.5 ip irdp minadvertinterval This command configures the minimum time, in seconds, allowed between sending router advertisements from the interface. The range for minadvertinterval is three to the value of maxadvertinterval. Default 0.75 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 262
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interface Ad Mode Advertise Address Max Int Min Int Hold Time Preference Shows the . Displays the advertise mode, which indicates whether router discovery is enabled or disabled on this interface. Displays the IP address to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 263
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.4.2 show ip vlan This command displays the VLAN routing information for all VLANs with routing enabled. Format show ip vlan Modes Privileged EXEC User EXEC MAC Address used by Routing VLANs Is the MAC Address associated with - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 264
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.1.1 no ip vrrp This command disables the VRRP protocol on an interface. This command also removes a virtual router IP address as a secondary IP address on an interface. The parameter is the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 265
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.3.1 no ip vrrp mode This command disables the virtual router configured on the specified interface. Disabling the status field stops a virtual router. Format no ip vrrp mode Mode Interface - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 266
the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.6 ip vrrp preempt This command sets the preemption mode value for the virtual router configured on a specified interface. The parameter is the virtual router ID, which is an integer from 1 to 255 Default enabled Format ip vrrp - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 267
vrrp interface stats This command displays the statistical information about each virtual router configured on the 7300 Series Managed Switch switch. Format show ip vrrp interface stats Modes Privileged EXEC User EXEC Uptime The time that the virtual router has been up, in - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 268
ProSafe 7300 Series Layer-3 Switches, Software Ver- IP TTL errors Zero Priority Packets Received Zero Priority Packets Sent Invalid Type Packets Received Address for which address list does not match the locally configured list for type' not equal to locally configured one for this virtual router. - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 269
Managed Switch. This command takes no options. It displays information about each virtual router. Format show ip vrrp interface Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. VRID Represents the router ID of the virtual router. IP Address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 270
Switches, Software Ver- 14.5.12 show ip vrrp interface This command displays all configuration information and VRRP router statistics of a virtual router configured on a specific interface. Format show ip vrrp interface Modes Privileged EXEC User EXEC IP Address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 271
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.2 enable (OSPF) This command resets the default administrative mode of OSPF in the router (active). Default enabled Format enable Mode Router OSPF Config 14.6.2.1 no enable (OSPF) This command - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 272
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.4.1 no 1583compatibility This command disables OSPF 1583 compatibility. Format no 1583compatibility Mode Router OSPF Config 14.6.5 area default-cost This command configures the monetary default cost for the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 273
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.8 area nssa no-redistribute (OSPF) This command configures the NSSA ABR so that learned external routes will not be redistributed to the NSSA. Format area nssa no-redistribute Mode Router - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 274
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.12 area range This command creates a specified area range for a specified NSSA. The is a valid IP address. The is a valid subnet mask. The LSDB type must be specified by either - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 275
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.13.1 no area stub This command deletes a stub area for the specified area ID. Format no area stub Mode Router OSPF Config 14.6.14 area stub summarylsa This command configures This command configures the default Summary LSA - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 276
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.16 area virtual-link authentication This command configures default value for authentication type is none. Neither the default password key nor the default key id are configured. Default configures to 65535. Default 40 Format area < - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 277
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.17.1 no area virtual-link dead-interval This command configures the default command configures the hello > is 1 to 65535. Default 10 Format area command configures the default hello configures Default 5 Format area - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 278
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.19.1 no area virtual-link retransmit-interval This command configures the default retransmit interval for the OSPF virtual interface on the virtual interface identified by and . The - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 279
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.21.1 no default-information originate (OSPF) This command is used to control the advertisement of default routes. Format no default-information originate [metric] [metrictype] Mode Router OSPF - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 280
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.24 distribute-list out Use this command to specify the access list to filter routes Default 0 Format exit-overflow-interval Mode Router OSPF Config 14.6.25.1 no exit-overflow-interval This command configures the default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 281
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.26 external-lsdb-limit This command configures the external LSDB limit for OSPF. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 282
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.28 ip key ID. Default none Format ip ospf authentication {none | Default 10 Format ip ospf cost Mode Interface Config 14.6.29.1 no ip ospf cost This command configures the default cost on an OSPF interface. Format no ip - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 283
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.30 ip ospf dead-interval This command multiple of the Hello Interval (i.e. 4). Default 40 Format ip ospf dead-interval Mode Interface Config Routing Commands v1.0, February 2007 14-43 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 284
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.30.1 no ip ospf dead-interval This command sets the default OSPF dead interval for the specified interface. Format no ip ospf dead-interval Mode Interface Config 14.6.31 ip ospf hello-interval This - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 285
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.33 ip ospf retransmit-interval This command hour). Default 1 Format ip ospf transmit-delay Mode Interface Config 14.6.34.1 no ip ospf transmit-delay This command sets the default OSPF Transit - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 286
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.35 ip ospf mtu-ignore This command disables OSPF maximum transmission unit (MTU) mismatch detection. OSPF Database Description packets specify the size of the largest IP packet that can be sent - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 287
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.37.1 no redistribute This command configures OSPF protocol to prohibit redistribution of routes maximum-paths This command resets the number of paths that OSPF can report for a given destination back to its default value. Format no maximum - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 288
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.40 show ip ospf This command displays information relevant to the OSPF router. Format show ip ospf Mode Privileged EXEC Note: Some of the information below displays only if you enable OSPF and configure certain features - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 289
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- New LSAs Originated LSAs Received External LSDB Limit Default Metric Default Route Advertise Always Metric Metric Type Maximum Paths Redistributing Source Metric Metric Type Tag Subnets Distribute-List - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 290
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.41 show ip ospf area This command displays information about the area. The identifies the OSPF area that is being displayed. Format show ip ospf area Modes Privileged EXEC User EXEC AreaID Is - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 291
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.42 show ip ospf database Externals are not grouped by area. Format show ip ospf database Modes Privileged EXEC User EXEC Note: The information below is only routing calculations. Router Options are valid for router links only - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 292
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.43 show ip ospf interface This command displays brief information for the IFO object or virtual interface tables. Format show ip ospf interface Modes Privileged EXEC User EXEC Interface Valid slot and port 2007 Routing Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 293
ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.44 show ip ospf interface This command displays the information for the IFO object or virtual interface tables. Format show ip ospf interface Modes Privileged EXEC User EXEC IP Address Represents the IP address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 294
for a specific interface. The information below will only be displayed if OSPF is enabled. Format show ip ospf interface stats Modes Privileged EXEC User EXEC OSPF Area ID The area id of this OSPF interface. Spf Runs The number of times that the intra-area route table has - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 295
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Neighbor ip ospf neighbor { | all} Modes Privileged EXEC User EXEC Router ID A 4 digit dotted decimal number representing the neighbor interface. IP Address An IP address Routing Commands v1.0, February 2007 14-55 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 296
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- which router is the IP address of the neighbor. Format show ip ospf neighbor Modes Privileged EXEC User EXEC Interface Valid slot and port number v1.0, February 2007 Routing Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 297
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Events Permanence Hellos Suppressed Retransmission Queue Length Attempt - no recent queue of the specified neighbor router Id of the specified interface. Routing Commands v1.0, February 2007 14-57 - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 298
Privileged EXEC User EXEC Area ID Is a 32-bit identifier for the created stub area. Type of Service Is the type of service associated with the stub metric. The 7300 Series Managed Switch only supports Normal TOS. Metric Val The metric value is applied based on the TOS. It defaults to the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 299
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Modes Area Id Neighbor Hello Interval Dead Interval Retransmit Interval Transit Delay show ip ospf virtual-link Privileged EXEC User EXEC The area id of the requested OSPF area. The neighbor - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 300
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- State Neighbor State The OSPF Interface States are: down, loopback, waiting, point-to-point, designated router, and backup designated router. This is the state of the OSPF interface. The neighbor state. 14.7 Routing Information Protocol - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 301
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.3.1 no ip rip This command disables RIP on a router interface. Format no ip rip Mode Interface Config 14.7.4 auto-summary This command enables the RIP auto-summarization mode. Default disabled Format auto - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 302
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.6.1 no default-metric (RIP) This command is used to reset the default metric of distributed routes to its default value. Format no default-metric Mode Router RIP Config 14.7.7 distance rip This - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 303
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.8.2 no default-information originate This command is used to control the advertisement of default routes. Format no default-information originate Mode Router RIP Config 14.7.9 ip rip authentication This command - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 304
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.10.1 no ip rip receive version This command configures the interface to allow RIP control packets of the default version(s) to be received. Format no ip rip receive version Mode Interface Config - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 305
the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.13 split-horizon This command sets the RIP split horizon mode. Default simple match types presently being redistributed. Internal routes are redistributed by default. Default metric - not-configured; match - internal Format for - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 306
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.15 show ip rip This command displays information relevant to the RIP router. Format show ip rip Modes Privileged EXEC User EXEC RIP Admin Mode Enable or disable. Split Horizon Mode None, simple - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 307
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.16 show ip rip interface This command displays general information for each RIP interface. For this command to display successful results routing must be enabled per interface (i.e. ip rip). Format show ip rip interface - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 308
ProSafe 7300 Series Layer-3 Switches, Software Ver- Link State Indicates whether the RIP interface is up or down. This is a configured value. Authentication Type The RIP Authentication Type for the specified interface. The types are none, simple, and encrypt. This is a configured value. Default - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 309
(IGMP) snooping commands available in the 7300 Series Managed Switch CLI. The 7300 Series Managed Switch supports IGMP Versions 1, 2, and 3. The IGMP snooping feature can help conserve bandwidth because it allows the switch to forward IP multicast traffic only to connected hosts that request - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 310
checksum) and discarding of the frame upon checksum error. • Maintenance of the forwarding table entries based on the MAC address versus the IP address. • Flooding of unregistered multicast data packets to all ports in the VLAN. Default disabled Format ip igmpsnooping Modes Global - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 311
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.2.1 no ip igmpsnooping interfacemode This command disables IGMP Snooping on all interfaces. Format no ip igmpsnooping interfacemode Mode Global Config 15.1.3 ip igmpsnooping groupmembership-interval This - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 312
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.4 ip igmpsnooping maxresponse This command sets the IGMP Maximum Response time for the system, on a particular interface or VLAN. The Maximum Response time is the amount of time in seconds that a - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 313
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.5.1 no ip igmpsnooping mcrtexpiretime This command sets the Multicast Router Present Expiration time to 0. The time is set for the system, on a particular interface or a VLAN. Format no ip igmpsnooping mcrtexpiretime - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 314
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.7.1 no ip igmp mrouter interface This command disables the forwarding of IGMP packets to a multicast router via this interface. Format no ip igmp mrouter interface Mode Interface Config 15.1.8 ip igmpsnooping unknown - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 315
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Admin Mode Interfaces Enabled for IGMP Snooping Multicast Control Frame Count VLANS Enabled for IGMP Snooping This indicates whether or not IGMP Snooping is active on the switch. This is the list of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 316
Layer-3 Switches, Software Ver- When you specify a value for , the following additional information appears: VLAN Admin Mode Indicates whether IGMP Snooping is active on the VLAN. 15.2.2 show ip igmp mrouter interface This command displays information about statically configured ports - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 317
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Type Description Interfaces displayed as a MAC address and VLAN ID combination of 8 bytes. Displays the type of the entry, which is either static (added by the user) or dynamic (added to the table as a - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 318
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • IGMP Snooping Querier Address (a configurable globally) 'or' • Switch Management Interface Address 'or' • First configured interface address (for L3 switches only) The switch will check for each of these IP addresses not being - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 319
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.3.3 ip igmpsnooping querier query-interval To configure the IGMP querier query interval for a VLAN , use the ip igmpsnooping querier query-interval command. Valid range for - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 320
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15-12 v1.0, February 2007 IGMP Snooping Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 321
the FSM7326P Switch software. The IEEE and powered terminals. The specification involves delivering 48 volts to Internet Protocol (IP) telephones, wireless switch or hub and the terminals (mid-span). Mid-span devices are available with 1,6,12 or 24 ports network solves that problem and allows greater - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 322
of service (QoS) where key users are given higher priority to power in the event of a outage. Voice-over IP (VoIP), is the transmission of telephone calls over a data network like one of the many networks that make up the Internet. Other NETGEAR products that work with the 7300 Series Managed Switch - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 323
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.1 poe This command enables or disables the Power over Ethernet function on the specified port(s). Default enable Format poe Mode Global Config 16.1.2 poe priority This command sets the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 324
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.4 poe usagethreshold This command Class 0 1 2 3 4 Usage Default Optional Optional Optional Not Allowed Max Power 0.44-12.95 0.44-3.84 3.84-6.49 6.49-12.95 Reserved 16.1.5.2 Output The Output field - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 325
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.5.3 Limit The LIMIT field is the preset limit defined by the "config poe port limit" command. This value is stated in watts. 16.1.5.4 Status The Status field reports the state of power supplied to the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 326
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16-6 v1.0, February 2007 Power Over Ethernet Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 327
maintenance commands available in the 7300 Series Managed Switch CLI. The System Maintenance Commands section configuration setting. • Copy commands transfer or save configuration and informational files to and from the switch. • Clear commands clear some or all of the settings to factory defaults - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 328
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.1 System Information and Statistics Commands This section describes the commands you use to view information about system features, components, and configurations. 17.1.1 show arp switch This command displays connectivity - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 329
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Switch Description Machine Type Machine Model Serial Number FRU Number Part Number Maintenance Level Manufacturer Burned in MAC Address Software Version Operating System Network Processing Device Additional - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 330
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The display parameters, when the argument is , is as follows: Packets Received Without Error The total number of packets (including broadcast packets and multicast packets) received by the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 331
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Transmitted Without Error Broadcast Packets Transmitted Transmit Packet Errors Address Entries Currently In Use VLAN Entries Currently In Use Time Since Counters Last Cleared Total number of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 332
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- before and after a common bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets). Packets Received 128-255 Octets - The total number - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 333
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- multicast address. Note that this number does not include packets directed to the broadcast address. Broadcast longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 334
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Received Packets Not Forwarded bad Frame Check Sequence (FCS) with an integral number of octets Overruns - The total number of frames discarded as this port was overloaded with incoming packets, and could - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 335
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Transmitted Octets Upstream Threshold - The number of frames discarded due to lack of cell descriptors available for that packet's priority level. Total Bytes - The total number of octets of data ( - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 336
ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Transmitted Successfully Transmit Errors Transmit Discards Max Info - The maximum size of the Info (non-MAC) field that this port will receive or transmit. Total - The number of frames to the Broadcast address, including those that - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 337
number of frames discarded on this port when a lookup on a particular VLAN occurs while that entry in the VLAN table is being modified, or if the VLAN has not been configured. BPDU's received - The count of BPDU's (Bridge Protocol Data Units) received in the spanning tree layer. BPDU's Transmitted - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 338
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Dot1x Statistics Frames Transmitted - The number of EAPOL frames of any type that have been transmitted by this authenticator. The elapsed time, in days, hours, minutes, and seconds since the statistics for this port - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 339
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Octets Transmitted - The total number of octets transmitted out of the interface, including framing characters. Packets Transmitted without Errors - The total number of packets transmitted out of the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 340
ProSafe 7300 Series Layer-3 Switches, Software Ver- Time Since Counters Last Cleared VLAN Deletes - The number of VLANs on this switch occurred since the last reset. The number of Address to display the table entry for the requested MAC address and all entries following the requested MAC address - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 341
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode Mac Address Interface Interface Index Status Static Learned Management Self GMRP Learned Other show mac-addr-table [ | all] Privileged EXEC A unicast MAC address for which the switch has forwarding and - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 342
ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.1.9 show running-config Use this command to display/capture the current setting of different protocol packages supported on the switch. This command displays/captures commands with settings/ configurations that differ from the default value - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 343
restore various configurations to their factory defaults. 17.2.1 traceroute Use the traceroute command to discover the routes that packets actually take when traveling to their destination through the network on a hop-by-hop basis. The value should be a valid IP address. The [port] value - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 344
the tables managed by the IGMP Snooping function and attempts to delete these entries from the Multicast Forwarding Database. Format clear igmpsnooping Mode Privileged EXEC 17.2.5 clear pass This command resets all user passwords to the factory defaults without powering off the switch. You are - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 345
ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode clear traplog Privileged EXEC 17.2.9 clear vlan This command resets VLAN configuration parameters to the factory defaults. Format clear vlan , the parameter is the IP address of the server, is the path to the - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 346
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Table 17-1. Copy Parameters (continued) Source secure-server certificate. Downloads an HTTP secure-server certificate. Downloads an HTTP secure-server certificate. Downloads the startup configuration - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 347
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.2.11 logout This command closes the current telnet connection or resets the current serial connection. Note: Save configuration changes before logging out. Format Mode logout Privileged EXEC 17.2.12 ping This command - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 348
ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3 Logging Commands This section describes the commands you use to configure Default enabled Format logging buffered wrap Mode Privileged EXEC 17.3.2.1 no logging wrap This command disables wrapping of in-memory logging and configures - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 349
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3.3 (5), informational (6), or debug (7). Default disabled; critical Format logging console [ You can configure up to eight hosts. The is the IP address of the logging host. The value is a port number from - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 350
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3.6 logging port This command sets the local port number of the LOG client for logging messages. The can be in the range from 1 to 65535. Default 514 Format logging port Mode Global Config - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 351
Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Console Logging Severity Filter . Messages with an equal or lower numerical severity are logged. The mode for logging to configured syslog hosts. If set to disable logging stops to all syslog hosts. The number of - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 352
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3.9 show logging buffered address. Port Displays the server port number, which is the port on the local host from which syslog messages are sent. Host Status The state of logging to configured syslog - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 353
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3.12 show logging traplogs This command displays SNMP trap events and statistics. Format show logging traplogs Mode Privileged EXEC Number of Traps Since Last Reset Shows the number of traps since - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 354
Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.5 Configuration Scripting Commands Configuration Scripting allows you to generate text-formatted script files representing the current configuration of a system. You can upload these configuration script files to - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 355
ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.5.2 script delete This command deletes a specified script where the parameter is the name of the script to delete. The option deletes all the scripts present on the switch problems. It might not identify all problems - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 356
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.6 Packet Capture Packet capture commands assist in troubleshooting protocol-related problems with the management CPU. The packets to and from the management CPU can be captured in an internally allocated - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 357
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.6.3 capture all packets This command wrap Mode Global Config Default Enabled 17.6.4.1 no capture all packets This command disables the Buffer Wrapping configuration. Format no capture wrap - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 358
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.6.5 show capture packets This command displays packets being captured from the buffer. The output of the show command can be redirected to a text - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 359
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.8.2 terminal no length This command resets the number of lines displayed by the show running-config command before pausing to the default value of 18. Format terminal no length Mode Global Config - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 360
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17-34 v1.0, February 2007 System Maintenance Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 361
Server (port 49) • Time Service (port 37) The system supports a maximum of 128 interface address-port pairs. For example, you can have a single UDP port forwarded on 128 different routing interfaces, or you can have 128 UDP ports forwarded on a single routing interface. When the switch receives - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 362
Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 18.1 UDP Relay Configuration Commands This section describes configuration commands for setting up UDP relay service. 18.1.1 ip helper-address (global config mode) Use the Global Configuration ip helper-address command to have - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 363
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 18.1.2 ip helper-address (interface config mode) The ip helper-address interface configuration command enables forwarding User Datagram Protocol (UDP) Broadcast packets received on an interface. Many - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 364
Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 18-4 v1.0, February 2007 UDP Relay Commands - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 365
brief show ip ospf virtual-link show ip vrrp interface brief show ip vrrp interface show monitor show monitor session shiow msglog show logging buferred show port-channel brief show port-channel show remotecon show telnet show service-policy show service-policy in show vlan brief show - Netgear GSM7324NA | FSM7326P Command line reference manual - Page 366
for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.0.3.4 Command set igmp maxresponse set igmp mctrexpiretime snmp-server enable traps snmp-server enable traps bcaststorm snmp-server enable traps linkmode snmp-server enable traps multiusers snmp-server enable traps
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
 |
 |
202-10236-01
February 2007
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Command Line Interface
Reference for the ProSafe
7300 Series Layer-3
Switches, Software
Version 6.0