Netgear XCM8806 Chassis XCM88PS1 Power Supply Installation Guide
Netgear XCM8806 Chassis Manual
View all Netgear XCM8806 Chassis manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear XCM8806 Chassis manual content summary:
- Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 1
8800 Series 100-240VAC PSU XCM88PS1 Hardware Installation Guide 350 East Plumeria Drive San Jose, CA 95134 USA February 2011 201-13472-02 1.0 - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 2
Installation Guide © 2011 NETGEAR, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc. Technical Support Thank - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 3
Contents Overview 4 Safety Information 4 Power Supply Cords 6 Pre-Installation Requirements 6 Installing an 8800 Series 100-240VAC PSU 7 Removing an 8800 Series 100-240VAC PSU 9 Front Panel LEDs 10 Fuse 10 Specifications 10 Contents | 3 - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 4
, specifications, and instructions for installing and PSUs. See the NETGEAR 8800 Series Chassis Switch User Manual for information on configuring your switch service personnel should perform service to switches and their components. Trained service personnel have read all related installation manuals - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 5
the hardware installation guide that describes your switch. • See Appendix A of the hardware installation guide that describes your the power supply into an electrical outlet when the power supply is outside the chassis; doing so would expose a hazardous energy and poses a potential shock and fire - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 6
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Power Supply Cords The following power supply cords are provided in the package with the PSU: Table 1. Power supply cords Model 10041 10042 10043 10044 - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 7
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Installing an 8800 Series 100-240VAC PSU CAUTION: Make sure that the PSU circuit is not overloaded. Use proper over-current protection, such as a circuit- - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 8
installed power supply, connect an appropriate AC power cord as follows: a. If necessary, remove the power cord retaining bracket as described in the hardware installation guide for your switch. b. Connect the new AC power cord to the AC input on the front of the switch to the wall outlet on the - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 9
cord: a. Remove the power cord retainer as described in the hardware installation guide for your switch. b. Completely disconnect and remove the old power cord. the PSU to support the weight as it is pulled out from the switch. 6. To install a replacement PSU, follow the instructions in the previous - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 10
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Front Panel LEDs The front panel of the 8800 Series 100-240VAC PSU provides status LEDs. The following table describes the operation of these LEDs. - Netgear XCM8806 Chassis | XCM88PS1 Power Supply Installation Guide - Page 11
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide More PSUs are needed to support the load if the low-line power range is used to power the switch. The software determines the maximum available power required for the switch
350 East Plumeria Drive
San Jose, CA 95134
USA
February 2011
201-13472-02
1.0
8800 Series 100-240VAC
PSU XCM88PS1
Hardware Installation Guide