Oki ES3640exMFPGA Finisher Unit Installation Guide

Oki ES3640exMFPGA Manual

Get Oki ES3640exMFPGA PDF manuals and user guides View all Oki ES3640exMFPGA manuals
Add to My Manuals
Save this manual to your list of manuals

Oki ES3640exMFPGA manual content summary:

  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 1
    Finisher Unit Installation Guide Components Step 1: Prepare the Printer 1. Turn the printer off (!) and disconnect the power cord (") and interface cable (#). 2. Using a screwdriver, remove the breakout panels on the side of the printer. 1 Finisher Unit 2 Finisher stand 3 Finisher Stacker 4
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 2
    3. Install the metal brackets where the breakout panels were. Step 2: Prepare the Inverter Before assembling the finisher, you must adjust the height of the inverter unit to match the finisher: ! Inverter as supplied " Inverter changed for use with 4-tray finisher. 4. Open the face-up stacker (!),
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 3
    2. Remove the two bottom caps: a. Turn the inverter over. 3. Turn the inverter around and remove the screws holding the metal brackets in place. Keep the screws and brackets handy: they are used to help secure the extension plate once it is repositioned. b. Remove the two screws securing the
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 4
    5. Pull forward on the extension plate to disengage the pins from the top channel stops, then slide it down into the inverter and push back to engage the pins on the bottom channel stops. 7. Turn the inverter around and reinstall the brackets. 6. Reattach the extension plate using the screws you
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 5
    using one screw on either side. 2. Attach the finisher stand to the inverter with 2 screws. 4. Attach the guard rail on the inverter stand to the printer using 2 screws. 5
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 6
    3. Place the finisher cover near the back of the finisher. Locate the tab (!) on the right side of the cover. 6. Place the large stopper over the tab on the cover and turn it to lock it in position. 4. Hold the clear band perpendicular to the cover and slip one end over the tab (!), then pivot the
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 7
    8. Pull the finisher platform about half way out, then loosen the screw on the locking piece (!: viewed from the opposite direction) so that it drops through the slot below it. This keeps the platform from moving while you attach the finisher to it. 9. Position the finisher on the stand and attach
  • Oki ES3640exMFPGA | Finisher Unit Installation Guide - Page 8
    1. Connect the finisher's cable to the inverter (!). Use the cable supplied to connect the inverter to the printer ("). 13. Push the finisher against the printer until the prongs on the printer brackets fit into the holes in the finisher. Note: If you need to, turn the levellers (!) on
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Finisher Unit Installation Guide
Components
1
Finisher Unit
7
Inverter Stand
2
Finisher stand
8
Clear Band
3
Finisher Stacker
9
Band Stopper, Small
4
Finisher Cover
10
Band Stopper, Large
5
Power Cord
11
Metal Brackets
6
Inverter Unit
12
Cable (inverter to printer)
Not illustrated: Screws
Step 1:
Prepare the Printer
1. Turn the printer off (
!
) and disconnect the
power cord (
"
) and interface cable (
#
).
2. Using a screwdriver, remove the breakout
panels on the side of the printer.