Panasonic AJHD1400 AJHD1400 User Guide - Page 62
Error messages, Warning messages continued
View all Panasonic AJHD1400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 62 highlights
Error messages (continued) Warning messages (continued) Priority Monitor display Description Corrective action VTR operation E-00 (SERVO NOT LOCKED) E-93 (INVALID TC MODE) E-94 (TC SEQUENCE UNMATCH) E-01 (LOW RF) This appears when the servo is not locked for three or more seconds during playback or recording. Check the tape. Operation continues. (In 23.98/24 Hz mode) Display when the time code is recorded in DF mode. On the drop point of the time code, the video output is garbled and audio output is muted. Operation of VTR continues. When using this unit to playback a tape recorded from a variable frame rate camera, it is necessary to record the time code in NDF mode. Use the original tape recorded with the variable frame rate camera. Operation continues. (In 23.98/24 Hz, 25 Hz, 50 Hz mode) Appear when the relationship between the active frame information and time code is not regular during playback. The video output may not be regular (not smooth). Operation of VTR continues. The active frame information (top frame of the switched frame image) is recorded on the tape from a variable Use the original tape recorded with the variable frame rate camera. Operation continues. frame rate camera. To play it back with this unit, it is necessary to detect the 0 frame of the time code at the activation frame position. This appears when an envelope level approximately onethird of the normal level has been detected for more than Clean the video heads. one second during playback or recording. Operation continues. Low E-02 (HIGH ERROR RATE) This appears when the error rate has increased to the extent that correction or interpolation was applied to either the video or audio playback signals. Clean the video heads. Operation continues. Error messages Monitor display E-29 FRONT LOAD MOTOR E-31 LOADING MOTOR E-35 SERVO CONTROL ERROR Description Corrective action VTR operation The unit switches to eject mode and if the cassette fails to move up within 6 seconds, this error number flashes on the display. If the cassette does not move down inside the machine even when 6 Set the POWER switch to OFF and then to ON again. STOP seconds have elapsed since the cassette was inserted, the VTR is transferred to the eject mode. If the unloading operation is not completed within 6 seconds, this error number flashes on the display. When the loading operation is not completed within 6 seconds, the VTR is transferred to the eject (unloading) mode. Set the POWER switch to OFF and then to ON again. STOP If there is no response from the servo microcomputer for 1 second or more, this error number flashes on the display. Set the POWER switch to OFF and then to ON again. STOP E-37 SERVO COMM ERROR E-38 SERVO FG ERROR E-51 FRONT LOAD ERROR E-52 W-UP REEL NOT ROTA E-53 WINDUP ERROR If 10 seconds or more elapses and the servo microcomputer has not followed orders issued by the system control microcomputer, this error number flashes on the display. Set the POWER switch to OFF and then to ON again. STOP This appears when the automatic reel and capstan rotation adjustment, which is performed in the EJECT mode, has not been carried out properly when the unit's power was switched on. Set the POWER switch to OFF and then to ON again. STOP If the take-up reel rotates without engaging for a specific period of time during the start or end processing operation while loading is underway (half position), this error number flashes on the display. Set the POWER switch to OFF and then to ON again. STOP If the take-up reel fails to take up the tape while the tape is traveling in the state where the total amount of the tape has not yet been detected after the cassette was inserted, this error number flashes Set the POWER switch to OFF and then to ON again. STOP on the display. If there is an abnormally large discrepancy between the amount of tape taken up by the take-up reel and the amount of tape supplied by the supply reel while the tape is traveling after the total amount of the tape begins to be detected, this error number flashes on the Set the POWER switch to OFF and then to ON again. STOP display. 62