Panasonic PTLB80NTU Lcd Projector

Panasonic PTLB80NTU - LCD PROJECTOR Manual

Get Panasonic PTLB80NTU - LCD PROJECTOR PDF manuals and user guides View all Panasonic PTLB80NTU manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic PTLB80NTU manual content summary:

  • Panasonic PTLB80NTU | Lcd Projector - Page 1
    Operating Instructions LCD Projector Commercial Use Model No. PT-LB80NTU PT-LB80U PT-LB78U PT-LB75NTU PT-LB75U Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0244-3 ENGLISH
  • Panasonic PTLB80NTU | Lcd Projector - Page 2
    with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-LB80NTU / PT-LB80U / PT-LB78U / PT-LB75NTU / PT-LB75U Serial number: WARNING
  • Panasonic PTLB80NTU | Lcd Projector - Page 3
    , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there PT-LB80NTU / PT-LB80U / PT-LB78U / PT-LB75NTU / PT-LB75U Trade Name: Panasonic Responsible party: Panasonic Corporation of North America Address: One Panasonic
  • Panasonic PTLB80NTU | Lcd Projector - Page 4
    See "Setting up" on page 15. 2. Connect with other devices See "Connections" on page 17. 3. Prepare the Remote control See "Remote control" on page 14. 4. Start projecting See "Switching the projector on/off" on page 18. 5. Adjust the image See "Menu Navigation" on page 27. B When you start the
  • Panasonic PTLB80NTU | Lcd Projector - Page 5
    écautions lors de l'utilisation 58 Sécurit 58 Remplacement de l'unité de la lampe 59 LAMP and TEMP Indicators 39 Managing the indicated problems 39 Care and Replacement 40 Cleaning the projector 40 Replacing the Lamp unit 41 Troubleshooting 43 Settings Maintenance Appendix ENGLISH - 5
  • Panasonic PTLB80NTU | Lcd Projector - Page 6
    wall outlet. Continued use of the projector in this condition may result in fire or electric shocks. Contact an Authorized Service Center for repairs. Insert the from the wall outlet immediately when problem occurred. Do not place the projector on soft materials such as carpets or sponge mats.
  • Panasonic PTLB80NTU | Lcd Projector - Page 7
    . Do not allow infants or pets to touch the remote control unit. Keep the remote control unit out of the reach of infants and pets after using it. CAUTIONS Do not cover the air inlet port or the air outlet port. Doing so may cause the projector to overheat, which can cause fire or damage
  • Panasonic PTLB80NTU | Lcd Projector - Page 8
    or leaving the remote control with batteries inside may lamp unit and check the inside of the projector. Ask an Authorized Service Center to clean inside the projector at least once a year. If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems
  • Panasonic PTLB80NTU | Lcd Projector - Page 9
    an untrusted third party. Locking out or prevent anyone else from using the projector by an untrusted third party. Security instruction Change your password regularly. Do not use too simple password to guess. Any of Authorized Service Centers will never ask you for the password. Do not share your
  • Panasonic PTLB80NTU | Lcd Projector - Page 10
    Accessories Make sure the following accessories are provided with your projector. Remote control for PT-LB80NTU / LB75NTU (x1)*1 N2QAYB000260 Remote control for PT-LB80U / LB78U / LB75U (x1)*2 N2QAYB000262 AA batteries for Remote control (x2) Power cord secure lock (x1) TTRA0185 Power cord (x1
  • Panasonic PTLB80NTU | Lcd Projector - Page 11
    method. Press G to proceed to the ALTITUDE setting. ENGLISH PLEASE SELECT LANGUAGE SELECT ENTER Press F G I H buttons of the remote control or control panel on the projector to highlight the required language, and press the ENTER button to proceed to the next setting. J OPTION Select the
  • Panasonic PTLB80NTU | Lcd Projector - Page 12
    (page 21) POWER indicator (page 21) LAMP indicator (page 39) TEMP indicator (page 39) Ambient Luminance Sensor (ALS) (page 30) Remote control signal receptor (page 23) RELEASE button Press to release the locked POWER button when turning on the projector. (page 19) POWER button Switch between
  • Panasonic PTLB80NTU | Lcd Projector - Page 13
    Attach a commercial burglar prevention cable. Remote control signal receptor (page 23) Lamp unit compartment (page 41) About Your Projector Security lock Attach the commercial shackle lock, manufactured by Kensington, to protect your projector. Compatible with the Kensington MicroSaver Security
  • Panasonic PTLB80NTU | Lcd Projector - Page 14
    Preparation About Your Projector Remote control POWER button Switch between stand-by mode and projection mode. (page 19/page 20) The PAGE buttons are only for PT-LB80NTU/ PT-LB75NTU. See CD-ROM contents. Display the main menu. (page 27) Navigate through the menus with FGIH, and activate the menu
  • Panasonic PTLB80NTU | Lcd Projector - Page 15
    : 3) Throw distance (L) PT-LB80NTU / LB80U Throw distance (L) PT-LB78U / LB75NTU / LB75U Screen diagonal Minimum distance Maximum distance use the projector at a raised or a horizontally tilted position as it may cause malfunction of the projector. • You can tilt the projector body approximately
  • Panasonic PTLB80NTU | Lcd Projector - Page 16
    projecting from rear INSTALLATION: FRONT/CEILING INSTALLATION: REAR/CEILING NOTE: • A translucent screen is required for rear projection. • When mounting the projector in the ceiling, the optional ceiling mount bracket (ET-PKB80) is required. Front leg adjusters and throwing angle You can adjust
  • Panasonic PTLB80NTU | Lcd Projector - Page 17
    instructions of each peripheral device. The peripheral devices must be turned off. One RGB cable is provided with the projector. If necessary, prepare commercial connecting cables that match with the projector the audio connection manually. Connecting example: PT-LB80NTU/PT-LB75NTU only) ENGLISH - 17
  • Panasonic PTLB80NTU | Lcd Projector - Page 18
    guide rail of the AC IN terminal of the projector and slide it in. Rail guide Latch 3. Slide the power cord secure lock up along the side guide rail and remove. Rail guide wall outlet or by switching off the main power. The internal lamp cooling fan keeps operating by the internal power supply, and
  • Panasonic PTLB80NTU | Lcd Projector - Page 19
    will not be displayed. See "STARTUP LOGO" on page 34. Q By remote control operation 1. Press the POWER button. 2. The POWER indicator flashes in green flicker for the characteristics of the lamp. Those are normal and will not affect the performance of the projector. • When the internal cooling
  • Panasonic PTLB80NTU | Lcd Projector - Page 20
    the POWER button again in 10 seconds. 3. The POWER indicator will flash in orange. The projector is cooling the lamp. 4. The POWER and POWER LOCK indicator switch to red. J By remote control operation 1. Press the POWER button. The confirmation screen will be displayed. Without any operation for
  • Panasonic PTLB80NTU | Lcd Projector - Page 21
    projector on/off POWER and POWER LOCK indicators The POWER indicator informs you the status of the power and the POWER LOCK indicator shows the status of the RELEASE button. When the LAMP Only when NETWORK STANDBY in NETWORK menu is ON. (PT-LB80NTU/PT-LB75NTU only) The power is on and preparing for
  • Panasonic PTLB80NTU | Lcd Projector - Page 22
    the SIGNAL SEARCH in OPTION menu is deactivated, select the required input method by pressing the INPUT SELECT buttons of the remote control or the INPUT SELECT button of the projector several times. See "SIGNAL SEARCH" on page 35, "Switching the input signal" on page 24 or "INPUT SELECT button" on
  • Panasonic PTLB80NTU | Lcd Projector - Page 23
    You can operate the projector with the remote control within the remote range 15 m (49'2"), approximately ± 30° vertically and horizontally. Q Facing to the projector Make sure the remote control emitter is facing to the remote control signal receptor of the projector when pressing the buttons
  • Panasonic PTLB80NTU | Lcd Projector - Page 24
    Remote control operation Switching the input signal You can switch the input method manually by pressing the COMPUTER, WIRELESS (PT-LB80NTU/PT guide on the upper right of the screen. Highlighted in yellow is selected terminal. See "INPUT GUIDE audio sound through the projector will stop. Press the
  • Panasonic PTLB80NTU | Lcd Projector - Page 25
    Basic Operation Remote control operation Projecting an image in INDEX-WINDOW mode You . See "PICTURE MODE" on page 30. See "CLOSED CAPTION SETTING" on page 36. Controlling the volume of the speaker You can control the volume of the built-in speakers and output audio sound. Press "+" side of the
  • Panasonic PTLB80NTU | Lcd Projector - Page 26
    Remote control operation Enlarging the centered area You can enlarge the projected image down to a centered area for emphasizing within the range of 1x to 2x. Q Shifting
  • Panasonic PTLB80NTU | Lcd Projector - Page 27
    Menu Navigation The menu system allows you to access functions which do not have their own dedicated buttons on the remote control. The menu options are structured and categorized. You can navigate through the menu with F G H I buttons. Navigating through the MENU J Displaying the main menu Press
  • Panasonic PTLB80NTU | Lcd Projector - Page 28
    Menu Navigation Main menu and Sub-menu The main menu has 6 options. Select the required menu item and press ENTER to display the sub-menu. Underlined items are factory default settings. NOTE: • Some default settings vary by the selected input signal. • sub-menu items vary according to the selected
  • Panasonic PTLB80NTU | Lcd Projector - Page 29
    GUIDE DETAILED SIMPLE OFF STARTUP LOGO ON OFF USER COMPUTER2 SELECT INPUT OUTPUT RGB/YPBPR AUTO RGB YPBPR WIDE MODE OFF ON LAMP POWER STANDARD ECO-MODE LAMP WIRELESS (PT-LB80NTU/PT-LB75NTU only) NETWORK NAME CHANGE INPUT PASSWORD PASSWORD CHANGE NETWORK STANDBY WEB CONTROL LIVE
  • Panasonic PTLB80NTU | Lcd Projector - Page 30
    PICTURE menu Remote control Control panel MENU RETURN COLOR You can adjust the color ON: Active OFF: Deactive NOTE: • Do not cover the Ambient Luminance Sensor (ALS) of the projector. See "Ambient Luminance Sensor (ALS)" on page 12. • AUTO is not available when INSTALLATION setting
  • Panasonic PTLB80NTU | Lcd Projector - Page 31
    . J For S-VIDEO/VIDEO signals Q TV-SYSTEM When the video signal is changed, the setting switches automatically. You can switch the setting manually to match the video data. Press I H to cycle through the options. AUTO NTSC NTSC 4.43 PAL SECAM PAL-N PAL-M NOTE: • AUTO setting will select from
  • Panasonic PTLB80NTU | Lcd Projector - Page 32
    Remote control Control menu and Sub-menu" on page 28. REALTIME KEYSTONE If the projector is aligned non-perpendicularly to the screen, or if the projection screen the REALTIME KEYSTONE is activated, you can correct the keystone manually. Image Operation NOTE: • If the projecting signal's dot
  • Panasonic PTLB80NTU | Lcd Projector - Page 33
    POSITION menu Q 16:9 The squeezed signal will be projected in 16:9 ratio. Q THROUGH The image will be projected without any size adjustment. Q S4:3 The input signal will be sized down 75 % and projected. S4:3 mode is effective when projecting 4:3 image on to a 16:9 screen. Q AUTO The signal
  • Panasonic PTLB80NTU | Lcd Projector - Page 34
    Remote control Control panel MENU RETURN See "Navigating through the MENU" on page 27. See "Main menu and Sub-menu" on page 28. INPUT GUIDE OUT RGB/YPBPR The projector will detect the signal from with AUTO setting, select RGB or YPBPR manually. WIDE MODE When projecting WIDE signals, switch
  • Panasonic PTLB80NTU | Lcd Projector - Page 35
    lamp replacement timing. See "Replacing the Lamp unit" on page 41. • When the lamp unit is replaced with the new unit, the setting need to be reset to "0". POWER OFF TIMER You can set the off timer to switch off the power of the projector for COMPUTER signals. See "Remote control" on page 14. NOTE
  • Panasonic PTLB80NTU | Lcd Projector - Page 36
    can reset all of the customized settings to the factory defaults except WIRELESS and LAMP RUNTIME menu settings. 1. Press the ENTER button 2. Turn off the projector by pressing the POWER button. 3. Reset the projector by unplugging and plugging the power cord from the wall outlet.. 4. The minimum
  • Panasonic PTLB80NTU | Lcd Projector - Page 37
    SECURITY menu Remote control Control panel PASSWORD CHANGE MENU RETURN See "Navigating through the MENU" projecting mode started. Unless you perform the correct password operation, all of the button controls will be disabled except the POWER button. OFF Deactive ON Active NOTE: • When
  • Panasonic PTLB80NTU | Lcd Projector - Page 38
    WIRELESS menu Remote control Control panel MENU RETURN See "Navigating through the MENU" on page 27. See "Main menu and Sub-menu" on page 28. NOTE: • The WIRELESS menu is available only with PT-LB80NTU/PT-LB75NTU. • See the wireless connecting information in the contents of the CD-ROM which is
  • Panasonic PTLB80NTU | Lcd Projector - Page 39
    the cause of the problem by status of the LAMP and/or TEMP indicators. 3. Follow the instruction for each indication below and solve the problem. 4. Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer. LAMP TEMP NOTE: • If no problem is found or
  • Panasonic PTLB80NTU | Lcd Projector - Page 40
    a cloth with water, wring the cloth well and then wipe the projector. Dry off the projector with dry cloth. Do not use petroleum benzine, thinner, any alcoholic replacing lamp unit. A replacement air filter is provided with a replacement lamp unit (ET-LAB80). Contact an Authorized Service Center
  • Panasonic PTLB80NTU | Lcd Projector - Page 41
    instructions which is provided with the lamp unit. • Do not use a lamp unit over 3 000 hours. Failure to observe this may result in explosion of the lamp. J Before replacing the lamp unit Contact an Authorized Service Center to purchase a replacement lamp unit (ET-LAB80). Switch off the projector
  • Panasonic PTLB80NTU | Lcd Projector - Page 42
    screws on the back of the projector until the screws turn freely, and remove the lamp unit cover. Lamp unit cover 3. Pull the used lamp unit gently from the projector. Grip the handle and keep the lamp unit paralleled when you remove the lamp. Some parts of the lamp unit are sharpened and may cause
  • Panasonic PTLB80NTU | Lcd Projector - Page 43
    Troubleshooting Should any problem persist, contact your dealer. Problem Cause Power does not turn on. No picture appears. The picture is fuzzy. The color is pale or grayish. No sound can be heard from the internal speaker. The control buttons of the projector do not operate. The Remote control
  • Panasonic PTLB80NTU | Lcd Projector - Page 44
    Technical Information List of compatible signals Mode Display resolution (dots)*1 Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) Picture quality*2 Terminals NTSC/NTSC 4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 525i (480i) 625i (576i) 525p (480p) 625p (576p) 1 125 (1 080)/60i 1 125 (1 080
  • Panasonic PTLB80NTU | Lcd Projector - Page 45
    connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer You can add the required parameter. The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending
  • Panasonic PTLB80NTU | Lcd Projector - Page 46
    COMPUTER2 NWP = WIRELESS (PT-LB80NTU/PT-LB75NTU only) Call back 0 = Standby 1 = Lamp on control active 2 = Lamp on 3 = Lamp off control active Turning off the while the INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. Manufacturer Panasonic NEC Key command
  • Panasonic PTLB80NTU | Lcd Projector - Page 47
    Information Screen size and throw distance for 16:9 aspect ratio Projection size (16 : 9) Throw distance (L) PT-LB80NTU / LB80U Throw distance (L) PT-LB78U / LB75NTU / LB75U Screen diagonal Minimum distance Maximum distance Minimum distance Maximum distance (SD) (LW) (LT) (LW) (LT
  • Panasonic PTLB80NTU | Lcd Projector - Page 48
    024 x 768) x 3 panels Manual zoom (1.2x)/Manual focus F 1.6 - 1.9, f 18.8 mm - 22.6 mm (PT-LB80NTU / LB80U) F 1.7 - 1.9, f 18.5 mm - 22.2 mm (PT-LB78U / LB75NTU / LB75U) 8.5:1 fixed (PT-LB80NTU / LB80U) 5:1 fixed (PT-LB78U / LB75NTU / LB75U) (page 15) UHM lamp (220 W) 3 200 lm (PT-LB80NTU / LB80U
  • Panasonic PTLB80NTU | Lcd Projector - Page 49
    (PT-LB80NTU/ PT-LB75NTU only) Compatible Wireless channel Distance IEEE802.11b/IEEE802.11g (Wireless LAN standard protocol) IEEE802.11b/IEEE802.11g: 1 - 13 channels 30 m (98'5") Depends on the usage environment Cabinet Dimensions Weight Certifications Power supply Operating range Remote control
  • Panasonic PTLB80NTU | Lcd Projector - Page 50
    Technical Information Dimensions 368 (14 - 15/32") Unit: mm 233 (9 - 5/32") 3 - 3/32" 93 3 - 21/32" 4 - 5/32" - 3/16" 5 9 88 - 11/32" 3 - 7/16" 2 - 1/8" 54.5 97 3 - 13/16" 3 - 15/32" 88.6 103.6 194.4 4 - 1/16" 7 - 5/8" Trademark acknowledgements VGA and XGA are trademarks of International
  • Panasonic PTLB80NTU | Lcd Projector - Page 51
    Remote control 25 Remote control button 14 INITIALIZE ALL 36 INPUT GUIDE 34 INPUT PASSWORD 37 INPUT SELECT Control panel button 12 Remote control button 14 Selecting 24 INSTALLATION Menu 35 Projection method 16 K KEYSTONE 32 L LAMP Indicator 12 Indicator status 39 LAMP POWER 35 LAMP
  • Panasonic PTLB80NTU | Lcd Projector - Page 52
    13 Replacing Air filter 40 Lamp unit 41 RETURN Control panel button 12 Remote control 27 Remote control button 14 RGB/YPBPR 34 Troubleshooting 43 TV-SYSTEM 31 V VARIABLE AUDIO OUT 13 VIDEO Remote control 24 Remote control button 14 VIDEO IN 13 VOLUME 36 Remote control 25 Remote control
  • Panasonic PTLB80NTU | Lcd Projector - Page 53
    votre projecteur LCD Panasonic. Le numéro de série de votre produit se trouve sous le projecteur. Veuillez le noter dans l'espace ci-dessous prévu à cet effet et conserver cette notice en cas de maintenance requise. Numéro de modèle: PT-LB80NTU / PT-LB80U / PT-LB78U / PT-LB75NTU / PT-LB75U Numéro
  • Panasonic PTLB80NTU | Lcd Projector - Page 54
    est pas installé et utilisé conformément aux instructions fournies avec celuici, peut provoquer des interférences PT-LB80NTU / PT-LB80U / PT-LB78U / PT-LB75NTU / PT-LB75U Désignation commerciale:Panasonic Fabricant responsable: Panasonic Corporation of North America Adresse: One Panasonic
  • Panasonic PTLB80NTU | Lcd Projector - Page 55
    est installé au plafond. Si l'installation n'est pas faite correctement, cela peut entraîner des blessures ou des chocs électriques. Ne pas utiliser un support de montage au plafond qui n'est pas agréé. Ne pas manipuler le cordon d'alimentation avec les mains mouillées. Cela peut entraîner des chocs
  • Panasonic PTLB80NTU | Lcd Projector - Page 56
    contre des objets durs ou si on la laisse tomber et des blessures et des mauvais fonctionnements peuvent s'ensuivre. Avant de remplacer la lampe, veiller à débrancher la fiche du cordon d'alimentation de la prise de courant. Il y a risque d'électrocution ou d'explosion. Ne pas laisser des enfants ou
  • Panasonic PTLB80NTU | Lcd Projector - Page 57
    ce qui peut entraîner des dommages ou des blessures. Si la lampe s'est cassée, ventiler immédiatement la pièce. Ne pas toucher ni un médecin immédiatement. S'adresser au revendeur pour le remplacement de la lampe et l'inspection de l'intérieur du projecteur. Demander à un centre technique agr
  • Panasonic PTLB80NTU | Lcd Projector - Page 58
    ceci n'affecte pas le bon fonctionnement de votre LCD. Ce projecteur est équipé d'une lampe au mercure sous haute pression, dont les principales (pour éviter une telle situation, vous pouvez verrouiller le projecteur). Instructions de sécurité Modifiez fréquemment votre mot de passe. N'utilisez
  • Panasonic PTLB80NTU | Lcd Projector - Page 59
    ésentent en aucun cas des durées garanties. • Pour plus d'informations sur l'unité de lampe et la période de garantie, consulter les instructions fournies avec l'unité de lampe. • N'utilisez pas de lampe plus de 3 000 heures. Sinon la lampe pourrait exploser. J Avant de remplacer le l'unité de la
  • Panasonic PTLB80NTU | Lcd Projector - Page 60
    contient du verre. Si elle tombe ou qu'elle reçoit un choc, elle pourrait s'endommager ou éclater. Q Réinitialisation de DURÉE DE LA LAMPE 1. Brancher le cordon d'alimentation à une prise et mettre le projecteur sous tension. 2. Appuyer sur la touche MENU pour afficher le menu. 3. Appuyer sur
  • Panasonic PTLB80NTU | Lcd Projector - Page 61
  • Panasonic PTLB80NTU | Lcd Projector - Page 62
    NOTE: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Printed in Japan S0308-5039F(P) TQBJ0244-3
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
E
NGLISH
Operating Instructions
LCD Projector
Model No.
PT-LB80NTU
PT-LB80U
PT-LB78U
PT-LB75NTU
PT-LB75U
Before operating this product, please read the instructions carefully and save this manual for future use.
TQBJ0244-3
Commercial Use