Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps Hydromatic SHE
Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps Manual
 |
View all Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps manuals
Add to My Manuals
Save this manual to your list of manuals |
Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps manual content summary:
- Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 1
safety instructions in this manual or on pump. This is the safety alert symbol. When you see this symbol on your pump or in this manual, look is required in normal operation. for overhaul, see instructions under "Service". California Proposition 65 Warning This product and related accessories - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 2
, burn, or kill. When installing, operating, or servicing this pump, follow the safety instructions listed below. 1. DO NOT splice the electrical power lift pump by power cord. CORD LIFT WARNING 1. Attempting to lift or support pump by power cord can damage cord and cord connections. 2. Cord may - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 3
is being removed for service, remove oil and replace it with new oil at reassembly. Use only oil listed in parts list in this manual. When filling with upside down to drain oil. a. Remove the three capscrews that secure the support legs. b. Remove the seven capscrews that secure the suction plate. c. - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 4
Hold the rotor shaft assembly and unscrew the impeller by turning it counter-clockwise. a. Remove impeller and clean it. b. If no more service is needed, reverse instructions above to reassemble the pump. c. Fill the pump with clean dielectric oil (Part No. U1978A). d. Be sure that the oil level is - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 5
EXPLODED VIEW 1 10 2 3 4 5 6A 6B 7 8 9 5740 1207 repair parts list Key Part Part No. Description Qty Number 1 Cord 115V 20' 1 1 Cord 115V 30' 1 1 Cord 230V 20' 1 1 Cord 230V 30' 1 • Cord Seal Ring 1 2 Motor Housing 1 3 Seal-Ring 1 4 Motor 1 5 Volute Case 1 6A Seal - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 6
TROUBLES-REMEDIES Sudden Starts. If the power is on to the pump when thermal overload resets, the pump may start without warning. If you are working on the pump, you may get an electrical shock or the impeller may catch fingers or tools. Disconnect the power before servicing instructions - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 7
You must pay all labor and shipping charges associated with this warranty and must request warranty service through the installing dealer as soon as a problem is discovered. No request for service will be accepted if received after the Warranty Period has expired. This warranty is not transferable - Pentair Pentair Hydromatic SHEF Series Cast Iron Effluent Pumps | Hydromatic SHE - Page 8
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
INSTALLATION, OPERATION & PARTS MANUAL
SHEF40
Submersible/Effluent Pump
© 2013 Pentair, Ltd. All Rights Reserved.
W-03-408 (Rev. 02/20/13)
293 WRIGHT STREET, DELAVAN, WI 53115
WWW.HYDROMATIC.COM
PH: 888±957±8677
MOTOR & CORD SPECIFICATIONS
SAFETY INFORMATION
Carefully read and follow all safety instructions in this
manual or on pump.
This is the safety alert symbol.
When you see this
symbol on your pump or in this manual, look for one of the
following signal words and be alert to the potential for
personal injury!
warns about hazards that
will
cause serious
personal injury, death or major property damage if ignored.
warns about hazards that
can
cause serious
personal injury, death or major property damage if ignored.
warns about hazards that
will
or
can
cause
minor personal injury or property damage if ignored.
The word
NOTICE
indicates special instructions which are
important but not related to hazards.
1.
Read these rules and instructions carefully.
Failure
to follow them could cause serious bodily injury and/or
property damage.
2.
Check your local codes before installing. You must
comply with their rules.
3.
Vent sewage or septic tank according to local codes.
4.
Do not install pump in any location classified as
hazardous by National Electrical Code, ANSI/NFPA
80-1984 or the Canadian Electrical Code.
Hazardous voltage. Can shock,
burn, or kill.
During operation the pump is in water.
To avoid fatal shocks, proceed as follows if pump needs
servicing:
Do not smoke or use devices that can generate sparks in a
septic (gaseous) environment.
5A. Disconnect power to outlet box before unplugging pump.
5B. Take extreme care when changing fuses. Do not stand
in water or put your finger in the fuse socket.
5C. Do not modify the cord and plug. When using the cord
and plug, plug into a grounded outlet only. When wiring
to a system control, connect the pump ground lead to
the system ground.
6. Be sure that
construction and
access to septic sumps
conform with all OSHA
requirements.
7. Do not run the pump
dry. Dry running can
overheat the pump,
(causing burns to
anyone handling it) and
will void the warranty.
8. The pump normally runs hot. To avoid burns when
servicing pump, allow it to cool for 20 minutes after
shutdown before handling it.
9. The pump is permanently lubricated. No oiling or
greasing is required in normal operation. for overhaul,
see instructions under “Service”.
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
DESCRIPTION
This submersible / effluent pump is designed for effluent and
wastewater removal, sump drainage, dewatering and flood
control. Units have built in thermal overload protection with
automatic reset. The mechanical seal and ball bearings on
the motor shaft are permanently lubricated. Stainless steel
hardware and a heavy duty lift out handle allow for easy
disassembly after extended use.
NOTICE:
This unit is not designed for applications involving
salt water or brine! Use with salt water or brine will void
warranty.
SPECIFICATIONS
Power supply required
.............
See “Motor, Switch and Cord
Specifications” chart below
Motor duty
.............................................................
Intermittent
Maximum Liquid Temperature
..........................
120°F (49°C)
Discharge Adapter
...............................................
1-1/2" NPT
Motor
Individual
Cord
Switch Setting
Discharge
Model
Motor
Full
Branch Circuit
Length*
in inches (mm)
Adapter
Number
HP
Voltage
Load Amps
Required (Amps)
in ft. (m)
On
Off
Size
SHEF40M1
4/10
115/1
12.0
15
20 (6.1)
-
-
1-1/2"
SHEF40A1
4/10
115/1
12.0
15
20 (6.1)
11.5 (292)
3.5 (89)
1-1/2"
SHEF40M2
4/10
230/1
6.0
15
20 (6.1)
-
-
1-1/2"
SHEF40A2
4/10
230/1
6.0
15
20 (6.1)
11.5 (292)
3.5 (89)
1-1/2"
*30' cord optional.