Philips 26PF8946 Quick start guide (English)
Philips 26PF8946 Manual
 |
View all Philips 26PF8946 manuals
Add to My Manuals
Save this manual to your list of manuals |
Philips 26PF8946 manual content summary:
- Philips 26PF8946 | Quick start guide (English) - Page 1
LCD TV 26PF8946 Quick Use Guide Thank you for purchasing this Philips LCD Television set. You are now the proud owner of a LCD TV set which promises full value to you as a customer. Before you proceed to install the LCD TV, please follow the steps and diagrams as shown to familiarise yourself with - Philips 26PF8946 | Quick start guide (English) - Page 2
VESA specifications. Pull out the back plate cover to access the four installing interfaces. Installation of the LCD TV on the wall should be carried out by qualified servicemen.Improper or incorrect installation may render the set unsafe. 3 LED light and infrared sensors Aim remote control at - Philips 26PF8946 | Quick start guide (English) - Page 3
TV. NOTE: Use the Source button on the remote control to tune to the AV1 channel for the cable box signal. Once tuned, change channels at the cable box, ohm) on the end, then you're ready to connect it to the TV. If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna - Philips 26PF8946 | Quick start guide (English) - Page 4
Your HD Receiver's jack panel may be labeled dif ferently. 3 AUDIO VCR CONTROL DIGITAL AUDIO OUT OUT TO TV CH 3 CH 4 HDMI VIDEO in 2 S-VIDEO IN FROM ANT SATELLITE IN Coxial Cable Lead-in fom Cable Outlet, Cable Converter Box, or VHF/UHF Antenna Coaxial cable Lead-in from Satellite Dish or - Philips 26PF8946 | Quick start guide (English) - Page 5
TV into the HD Mode and tune to the computer's signal. Note : For the display resolutions available to your TV, refer to the Operating Instruction Manual Please contact your dealer or Philips at 1-888 PHILIPS device and the TV ON. 4 Press the Source button on the remote control to select the AV3
-
1 -
2 -
3 -
4 -
5
 |
 |
If you intend to install the LCD TV on the wall. ensure you have the following :
– Standard
VESA 100 bracket for LCD TV (not supplied) and four spacers found in the accessory bag.
3139 125
33871
Thank you for purchasing this Philips LCD Television set. You are now the proud owner
of a LCD TV set which promises full value to you as a customer. Before you proceed to
install the LCD TV, please follow the steps and diagrams as shown to familiarise yourself
with the correct and safe way of assembling the stand to the TV.
2
3
A
SSEMBLING THE
S
TAND
I
NSTALLING
LCD TV
ON THE
W
ALL
Bottom of swivel base
Check the stand arm is rigid and
properly installed. Place the
set upright.
VESA
Bracket
does not
fit
If your VESA bracket does not fit into the slot at
the rear of the LCD TV, proceed to make use of
the four spacers provided. Note : If VESA bracket
fits into the slot, you need not use the spacers.
1
2
3
Spacer
x 4
Screw the four spacers to the holes at the rear of
the set. Ensure the spacers are properly tightened
(torque of 1.2N-m or 1 lbf-in).
Tighten
VESA
bracket
to spacers
Close back plate cover by gently
pushing downwards.
Align arrow
to the center
1
For swivelling of the stand to function properly, adjust the swivel base at
the back of the stand until arrow is aligned in the center. Align the stand
studs into the holes at the bottom of the set. Put in the screws (provided)
into the 2 holes and tightened with a screwdriver.
CAUTION : While putting in the screws, hold onto the stand.
Place the set facing down on a protective
sheet close to the edge of a flat surface.
Ensure you have the following before
you assemble the stand :
–
Two screws
(supplied with set)
–
One Screwdriver
(not supplied)
4
Do the following when installing the LCD TV on the wall :
2
1
Ñ
Ñ
Ñ
!
Place the VESA bracket on the spacers and
tightened with the VESA bracket screws.
Open back plate cover by gently pulling upwards.
Quick Use Guide
LCD TV
26PF8946